Get rid of the need to check if boot_dev_sts is valid on every access
to value read from these registers.

This is done by storing the register value in hdev props ONLY if
register is enabled.

This way if register is NOT enabled all capability bits will not be set.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

If device is not idle after user closes the FD we must reset device
as next user that will try to open FD will encounter a non-functional
device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Sometimes it is useful to allow the command to continue running despite
the timeout occurred, to differentiate between really stuck or just very
time consuming commands. This can be achieved by passing a new debug
flag alongside the cs, HL_CS_FLAGS_SKIP_RESET_ON_TIMEOUT.

Anyway, if the timeout occurred, a warning print shall be issued,
however this shall not fail the submission.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In order for driver to be aware of process or thread crashes inside
GAUDI's CPU, we introduce a new event which contains all relevant
information. Upon event reception, driver will dump information and
will reset the device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In the collective wait, we put jobs on the QMANs of all the NICs. The
code takes into account if a port is disabled only in case of PCI card.
When this info arrives from the f/w, the code doesn't take it into
account, and it tries to schedule jobs on NICs that aren't enabled and
thats a bug.

To fix this, after the f/w sends us the list of disabled ports, we
update the state of the QMANs according to that list. In addition,
we need to update the HW_CAP bits so the collective wait operation
will not try to use those QMANs. We also need to update the collective
master monitor mask.

Moreover, we need to add a protection for such future cases and in case
the user will try to submit work to those QMANs.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Update the firmware interface files to their latest version.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Current implementation uses a single interrupt interface towards
FW, this interface is causing races between interrupt types.
We split this interface to interface per interrupt type.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

There is no dependency when probing multiple devices so indicate to the
kernel that it can probe our devices in ASYNC fashion.

This shortens insmod of the driver from ~2 minutes to 20 seconds on
a system with 8 devices.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Update the QM stop on error masks to also stop on ARB errors.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

nic_ports_mask is used by the networking part of the driver.
In the compute part, we use the HW_CAP bits to select what is active
and what is not.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

This fix was applied since there was an incorrect reported CPU ID to GIC
such that an error in MME2 QMAN aliased to be an arriving from DMA0_QM.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

After all the latest changes to the reset code, there were some
redundancy and errors in the flows.

If the Linux FIT is loaded to the ASIC CPU, we need to communicate
with it only via GIC. If it is not loaded, we need to either use
COMMS protocol (for newer f/w) or MSG_TO_CPU register (for older f/w).

In addition, if we halted the device CPU then we need to mark that
the driver will do the reset, regardless of the capabilities.

Also, to prevent false errors, we need to keep track whether the
device CPU was already halted. If so, we shouldn't try to halt it
again.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Using negative logic (i.e. fw_security_disabled) is confusing.

Modify the flag to use positive logic (fw_security_enabled).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

This is needed because legacy FW 'communication' protocol will soon
become obsolete.
Because COMMS is a boot protocol, communicating through it is supported
only until Linux is loaded to the device CPU, where in that case we
will fallback to the former implementation.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Security is set based on PCI ID, and after reading preboot status bits.
GIC usage is set in both scenarios since GIC can't be used when security
is enabled.
Moreover, writing to GIC/SP is enabled only after Linux is fully loaded.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

On newer releases, host won't be able to trigger an interrupt directly
to the ASIC GIC controller.
To be able to decide whether GIC can/not be used, we must read device's
preboot status bits in a stage that precedes the possible first use of
GIC (when device is in dirty state).
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

To harden the event queue mechanism, we add a running index to the
control header of the entry.

The firmware writes the index in each entry and the driver verifies
that the index of the current entry is larger by 1 of the index of
the previous entry.

In case it isn't, the driver will treat the entry as if it wasn't
valid (it won't process it but won't skip it).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Scrubbing memory after every unmap is very costly in terms of
performance. If a user wants it he can enable it but the default
should prioritize performance.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

As iATU configuration is done by FW, driver should not try and
move HBM bar.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Reading of GIC privileged status will be done after F/W is loaded,
because privileged GIC capability is only available with the correct
ARMCP version, and after it's loaded.
Such versions necessarily support COMMS, so GIC alternatives (SP regs)
will be read directly from dynamic regs.

As well, initiation of DMA QMANs will occur after F/W is loaded
since it depends on GIC configuration.

In case F/W isn't loaded there's no problem since either way
there won't be any GIC IRQ handling.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Fix issue in which the input to the function is_asic_secured was device
PCI_IDS number instead of the asic_type enumeration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

LKD should provide hard reset cause to preboot prior to
loading any FW components (in case needed).
Current implementation is based on the new FW 'COMMS' protocol
In cased 'COMMS' is disabled - reset cause won't be sent.
Currently, only 2 reset causes are shared: HEARTBEAT & TDR.

Sending the reset cause will provide the missing watchdog
info that the firmware needs to provide to the BMC.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

An information print notifying on starting to load the f/w was removed
by mistake when moving to the new dynamic f/w loading mechanism.

Restore that print as the F/W loading usually takes between 10 to 20
seconds and this print helps the user know the status of the driver
load.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Due to new security restrictions, GIC controller can no
longer be accessed from user/kernel.
To monitor that, a new status bit will be read from preboot
caps, indicating whether direct access to GIC is blocked.

In case it is blocked, driver will use scratchpad registers
instead of using GIC interface on two main scenarios:
The first of which LKD triggers interrupts to F/W through GIC,
and the second of when LKD configures all engines/QMANs
to write to GIC when they want to report an error.

From F/W perspective, it will poll on all SPs, and once IRQ
number is retrieved, SP register is cleared, and it will perform the
write to the GIC to trigger the IRQ handler.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Maintain both STS1 and ERR1 registers used for status communication
with F/W.
Those are not maintained as we currently have less than 31
statuses/error defined and so LKD did not refer to those register.
The reason to read them now is to try to support future f/w versions
with current driver.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

When attempting to read FW component's version we should break if input
FW component is invalid in order to avoid using uninitialized
destination pointer.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

When setting "DMA mask from FW" we are reading PSOC_GLOBAL_CONF register
which is allowed only once FW has done it's iATU configuration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Print the user given pointer and error code on failure to get user
pages for easier debugging.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Change casting code according to kernel coding style.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Some users might want to implement their own policy of when the device
is unusable so we need to ignore this status in the driver and continue
loading as normal.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Implementing dynamic linux image load to the device.
This patch also implements the FW communication steps during the
boot-fit.
This patch also enables the dynamic protocol based on the compatibility
flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Implementing dynamic boot fit image load to the device.
Note that some necessary adjustment were added to the static loader as
well so that both loaders can co-exist.
as this is not the final FW load stage the dynamic FW load is still
forced to be non functional.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Hint address failure that results in a valid mapping with an address
that was allocated by the driver is not a real failure.

Therefore, the driver shouldn't notify about this in kernel log. The
user is responsible to check the returned address.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Indicate "progress" instead of "error" when reporting progress status.

Change "u-boot stopped by user" to "Cannot boot" message as
CPU_BOOT_STATUS_UBOOT_NOT_READY may indicate a fatal error that prevent
u-boot from loading firmware.
Signed-off-by: Guy Nisan <gnisan@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

iATU (internal Address Translation Unit of the PCI controller)
configuration is being done by FW right after driver enables
the PCI device. Hence, driver must add a minor sleep afterwards
in order to make sure FW finishes configuring iATU regions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Update the common and GAUDI firmware header files to the latest version.

The latest version use the correct endianness types so this commit also
contains minor changes to the code to use the correct conversions when
reading/writing to the firmware structures.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

LKD has interfaces in which it receives device address.
For instance the debugfs_read/write variants receives device address for
CFG/SRAM/DRAM for read/write and need to translate to the mapped PCI BAR
address.

In addition, the dynamic FW load protocol dictates that the address to
which the LKD will copy the image for the next FW component will be
received as a device address and can be placed either in SRAM or DRAM.

We need to distinguish those regions as the access methods to those
regions are different (in DRAM we possibly need to set the BAR base).

Looking forward this code will be used to remove duplicated code in the
debugfs_read/write that search the memory region for the input device
address.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

First stage of the dynamic FW load protocol is to reset the protocol to
avoid residues from former load cycles.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Instead of using multiple ASIC specific copies of functions to read the
FW version use single common one that gets ASIC specific arguments.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Use mmu cache range invalidation instead of entire cache invalidation
because it yields better performance.

In GOYA and GAUDI, always use entire cache invalidation because these
ASICs don't support range invalidation.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>