- 28 Jul, 2019 9 commits
-
-
Baruch Siach authored
[ Upstream commit 7b75e49d ] Add a 1ms delay after reset deactivation. Otherwise the chip returns bogus ID value. This is observed with 88E6390 (Peridot) chip. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Justin Chen authored
[ Upstream commit 35cbef98 ] Currently we silently ignore filters if we cannot meet the filter requirements. This will lead to the MAC dropping packets that are expected to pass. A better solution would be to set the NIC to promisc mode when the required filters cannot be met. Also correct the number of MDF filters supported. It should be 17, not 16. Signed-off-by:
Justin Chen <justinpopo6@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Ido Schimmel authored
[ Upstream commit 54851aa9 ] When a route needs to be appended to an existing multipath route, fib6_add_rt2node() first appends it to the siblings list and increments the number of sibling routes on each sibling. Later, the function notifies the route via call_fib6_entry_notifiers(). In case the notification is vetoed, the route is not unlinked from the siblings list, which can result in a use-after-free. Fix this by unlinking the route from the siblings list before returning an error. Audited the rest of the call sites from which the FIB notification chain is called and could not find more problems. Fixes: 2233000c ("net/ipv6: Move call_fib6_entry_notifiers up for route adds") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reported-by:
Alexander Petrovskiy <alexpe@mellanox.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David Ahern authored
[ Upstream commit 49d05fe2 ] Paul reported that l2tp sessions were broken after the commit referenced in the Fixes tag. Prior to this commit rt6_check returned NULL if the rt6_info 'from' was NULL - ie., the dst_entry was disconnected from a FIB entry. Restore that behavior. Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by:
Paul Donohue <linux-kernel@PaulSD.com> Tested-by:
-
Matteo Croce authored
[ Upstream commit 2e605463 ] Avoid the situation where an IPV6 only flag is applied to an IPv4 address: # ip addr add 192.0.2.1/24 dev dummy0 nodad home mngtmpaddr noprefixroute # ip -4 addr show dev dummy0 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 inet 192.0.2.1/24 scope global noprefixroute dummy0 valid_lft forever preferred_lft forever Or worse, by sending a malicious netlink command: # ip -4 addr show dev dummy0 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 inet 192.0.2.1/24 scope global nodad optimistic dadfailed home tentative mngtmpaddr noprefixroute stable-privacy dummy0 valid_lft forever preferred_lft forever Signed-off-by:
Matteo Croce <mcroce@redhat.com> Reviewed-by:
-
Eric Dumazet authored
[ Upstream commit e5b1c6c6 ] im->tomb and/or im->sources might not be NULL, but we currently overwrite their values blindly. Using swap() will make sure the following call to kfree_pmc(pmc) will properly free the psf structures. Tested with the C repro provided by syzbot, which basically does : socket(PF_INET, SOCK_DGRAM, IPPROTO_IP) = 3 setsockopt(3, SOL_IP, IP_ADD_MEMBERSHIP, "\340\0\0\2\177\0\0\1\0\0\0\0", 12) = 0 ioctl(3, SIOCSIFFLAGS, {ifr_name="lo", ifr_flags=0}) = 0 setsockopt(3, SOL_IP, IP_MSFILTER, "\340\0\0\2\177\0\0\1\1\0\0\0\1\0\0\0\377\377\377\377", 20) = 0 ioctl(3, SIOCSIFFLAGS, {ifr_name="lo", ifr_flags=IFF_UP}) = 0 exit_group(0) = ? BUG: memory leak unreferenced object 0xffff88811450f140 (size 64): comm "softirq", pid 0, jiffies 4294942448 (age 32.070s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 ff ff ff ff 00 00 00 00 ................ 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 ................ backtrace: [<00000000c7bad083>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline] [<00000000c7bad083>] slab_post_alloc_hook mm/slab.h:439 [inline] [<00000000c7bad083>] slab_alloc mm/slab.c:3326 [inline] [<00000000c7bad083>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553 [<000000009acc4151>] kmalloc include/linux/slab.h:547 [inline] [<000000009acc4151>] kzalloc include/linux/slab.h:742 [inline] [<000000009acc4151>] ip_mc_add1_src net/ipv4/igmp.c:1976 [inline] [<000000009acc4151>] ip_mc_add_src+0x36b/0x400 net/ipv4/igmp.c:2100 [<000000004ac14566>] ip_mc_msfilter+0x22d/0x310 net/ipv4/igmp.c:2484 [<0000000052d8f995>] do_ip_setsockopt.isra.0+0x1795/0x1930 net/ipv4/ip_sockglue.c:959 [<000000004ee1e21f>] ip_setsockopt+0x3b/0xb0 net/ipv4/ip_sockglue.c:1248 [<0000000066cdfe74>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2618 [<000000009383a786>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3126 [<00000000d8ac0c94>] __sys_setsockopt+0x98/0x120 net/socket.c:2072 [<000000001b1e9666>] __do_sys_setsockopt net/socket.c:2083 [inline] [<000000001b1e9666>] __se_sys_setsockopt net/socket.c:2080 [inline] [<000000001b1e9666>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2080 [<00000000420d395e>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<000000007fd83a4b>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 24803f38 ("igmp: do not remove igmp souce list info when set link down") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Hangbin Liu <liuhangbin@gmail.com> Reported-by: syzbot+6ca1abd0db68b5173a4f@syzkaller.appspotmail.com Signed-off-by:
-
Haiyang Zhang authored
[ Upstream commit be4363bd ] There is an extra rcu_read_unlock left in netvsc_recv_callback(), after a previous patch that removes RCU from this function. This patch removes the extra RCU unlock. Fixes: 345ac089 ("hv_netvsc: pass netvsc_device to receive callback") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit fdd258d4 ] cfhsi_exit_module() calls unregister_netdev() under rtnl_lock(). but unregister_netdev() internally calls rtnl_lock(). So deadlock would occur. Fixes: c4125400 ("caif-hsi: Add rtnl support") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Brian King authored
[ Upstream commit ea811b79 ] This patch fixes an issue seen on Power systems with bnx2x which results in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons load in bnx2x_tx_int. Adding a read memory barrier resolves the issue. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
- 26 Jul, 2019 31 commits
-
-
Greg Kroah-Hartman authored
-
Junxiao Bi authored
commit bd293d07 upstream. When thin-volume is built on loop device, if available memory is low, the following deadlock can be triggered: One process P1 allocates memory with GFP_FS flag, direct alloc fails, memory reclaim invokes memory shrinker in dm_bufio, dm_bufio_shrink_scan() runs, mutex dm_bufio_client->lock is acquired, then P1 waits for dm_buffer IO to complete in __try_evict_buffer(). But this IO may never complete if issued to an underlying loop device that forwards it using direct-IO, which allocates memory using GFP_KERNEL (see: do_blockdev_direct_IO()). If allocation fails, memory reclaim will invoke memory shrinker in dm_bufio, dm_bufio_shrink_scan() will be invoked, and since the mutex is already held by P1 the loop thread will hang, and IO will never complete. Resulting in ABBA deadlock. Cc: stable@vger.kernel.org Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Josua Mayer authored
commit 80785f5a upstream. Armada 8040 needs four clocks to be enabled for MDIO accesses to work. Update the binding to allow the extra clock to be specified. Cc: stable@vger.kernel.org Fixes: 6d6a331f ("dt-bindings: allow up to three clocks for orion-mdio") Reviewed-by:
Josua Mayer <josua@solid-run.com> Signed-off-by:
-
Josua Mayer authored
commit 4aabed69 upstream. Allow up to four clocks to be specified and enabled for the orion-mdio interface, which are required by the Armada 8k and defined in armada-cp110.dtsi. Fixes a hang in probing the mvmdio driver that was encountered on the Clearfog GT 8K with all drivers built as modules, but also affects other boards such as the MacchiatoBIN. Cc: stable@vger.kernel.org Fixes: 96cb4342 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio") Reviewed-by:
-
Tejun Heo authored
commit f539da82 upstream. Depending on the number of devices, blkcg stats can go over the default seqfile buf size. seqfile normally retries with a larger buffer but since the ->pd_stat() addition, blkcg_print_stat() doesn't tell seqfile that overflow has happened and the output gets printed truncated. Fix it by calling seq_commit() w/ -1 on possible overflows. Signed-off-by:
Tejun Heo <tj@kernel.org> Fixes: 903d23f0 ("blk-cgroup: allow controllers to output their own stats") Cc: stable@vger.kernel.org # v4.19+ Cc: Josef Bacik <jbacik@fb.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Tejun Heo authored
commit 5de0073f upstream. If use_delay was non-zero when the latency target of a cgroup was set to zero, it will stay stuck until io.latency is enabled on the cgroup again. This keeps readahead disabled for the cgroup impacting performance negatively. Signed-off-by:
-
Konstantin Khlebnikov authored
commit 3a10f999 upstream. After commit 991f61fe ("Blk-throttle: reduce tail io latency when iops limit is enforced") wait time could be zero even if group is throttled and cannot issue requests right now. As a result throtl_select_dispatch() turns into busy-loop under irq-safe queue spinlock. Fix is simple: always round up target time to the next throttle slice. Fixes: 991f61fe ("Blk-throttle: reduce tail io latency when iops limit is enforced") Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: stable@vger.kernel.org # v4.19+ Signed-off-by:
-
Lee, Chiasheng authored
commit e244c469 upstream. With Link Power Management (LPM) enabled USB3 links transition to low power U1/U2 link states from U0 state automatically. Current hub code detects USB3 remote wakeups by checking if the software state still shows suspended, but the link has transitioned from suspended U3 to enabled U0 state. As it takes some time before the hub thread reads the port link state after a USB3 wake notification, the link may have transitioned from U0 to U1/U2, and wake is not detected by hub code. Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup handling This patch should be added to stable kernels since 4.13 where LPM was kept enabled during suspend/resume Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by:
Lee, Chiasheng <chiasheng.lee@intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Szymon Janc authored
commit 1d87b88b upstream. Microsoft Surface Precision Mouse provides bogus identity address when pairing. It connects with Static Random address but provides Public Address in SMP Identity Address Information PDU. Address has same value but type is different. Workaround this by dropping IRK if ID address discrepancy is detected. > HCI Event: LE Meta Event (0x3e) plen 19 LE Connection Complete (0x01) Status: Success (0x00) Handle: 75 Role: Master (0x00) Peer address type: Random (0x01) Peer address: E0:52:33:93:3B:21 (Static) Connection interval: 50.00 msec (0x0028) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Master clock accuracy: 0x00 .... > ACL Data RX: Handle 75 flags 0x02 dlen 12 SMP: Identity Address Information (0x09) len 7 Address type: Public (0x00) Address: E0:52:33:93:3B:21 Signed-off-by:
Szymon Janc <szymon.janc@codecoup.pl> Tested-by:
Maarten Fonville <maarten.fonville@gmail.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199461 Cc: stable@vger.kernel.org Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Alexander Shishkin authored
commit 918b8646 upstream. Commit 4e0eaf23 ("intel_th: msu: Fix single mode with IOMMU") switched the single mode code to use dma mapping pages obtained from the page allocator, but with IOMMU disabled, that may lead to using SWIOTLB bounce buffers and without additional sync'ing, produces empty trace buffers. Fix this by using a DMA32 GFP flag to the page allocation in single mode, as the device supports full 32-bit DMA addressing. Signed-off-by:
Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: 4e0eaf23 ("intel_th: msu: Fix single mode with IOMMU") Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reported-by:
Ammy Yi <ammy.yi@intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190621161930.60785-4-alexander.shishkin@linux.intel.comSigned-off-by:
-
liaoweixiong authored
commit b83408b5 upstream. In case of the last page containing bitflips (ret > 0), spinand_mtd_read() will return that number of bitflips for the last page while it should instead return max_bitflips like it does when the last page read returns with 0. Signed-off-by:
Weixiong Liao <liaoweixiong@allwinnertech.com> Reviewed-by:
Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by:
Frieder Schrempf <frieder.schrempf@kontron.de> Cc: stable@vger.kernel.org Fixes: 7529df46 ("mtd: nand: Add core infrastructure to support SPI NANDs") Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by:
-
Xiaolei Li authored
commit e1884ffd upstream. At present, the flow of calculating AC timing of read/write cycle in SDR mode is that: At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min. Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min. But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now. This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement. Fixes: edfee361 ("mtd: nand: mtk: add ->setup_data_interface() hook") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by:
Xiaolei Li <xiaolei.li@mediatek.com> Reviewed-by:
-
Dan Carpenter authored
commit 0bdf8a82 upstream. ECRYPTFS_SIZE_AND_MARKER_BYTES is type size_t, so if "rc" is negative that gets type promoted to a high positive value and treated as success. Fixes: 778aeb42 ("eCryptfs: Cleanup and optimize ecryptfs_lookup_interpose()") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> [tyhicks: Use "if/else if" rather than "if/if"] Cc: stable@vger.kernel.org Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Jorge Ramirez-Ortiz authored
commit 5e6b6651 upstream. mutexes can sleep and therefore should not be taken while holding a spinlock. move clk_get_rate (can sleep) outside the spinlock protected region. Fixes: 83736352 ("mmc: sdhci-msm: Update DLL reset sequence") Cc: stable@vger.kernel.org Signed-off-by:
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Vinod Koul <vkoul@kernel.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Nathan Lynch authored
commit 0aa82c48 upstream. During post-migration device tree updates, we can oops in pseries_update_drconf_memory() if the source device tree has an ibm,dynamic-memory-v2 property and the destination has a ibm,dynamic_memory (v1) property. The notifier processes an "update" for the ibm,dynamic-memory property but it's really an add in this scenario. So make sure the old property object is there before dereferencing it. Fixes: 2b31e3ae ("powerpc/drmem: Add support for ibm, dynamic-memory-v2 property") Cc: stable@vger.kernel.org # v4.16+ Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Greg Kurz authored
commit 02c5f539 upstream. Since 902bdc57, get_pci_dev() calls pci_get_domain_bus_and_slot(). This has the effect of incrementing the reference count of the PCI device, as explained in drivers/pci/search.c: * Given a PCI domain, bus, and slot/function number, the desired PCI * device is located in the list of PCI devices. If the device is * found, its reference count is increased and this function returns a * pointer to its data structure. The caller must decrement the * reference count by calling pci_dev_put(). If no device is found, * %NULL is returned. Nothing was done to call pci_dev_put() and the reference count of GPU and NPU PCI devices rockets up. A natural way to fix this would be to teach the callers about the change, so that they call pci_dev_put() when done with the pointer. This turns out to be quite intrusive, as it affects many paths in npu-dma.c, pci-ioda.c and vfio_pci_nvlink2.c. Also, the issue appeared in 4.16 and some affected code got moved around since then: it would be problematic to backport the fix to stable releases. All that code never cared for reference counting anyway. Call pci_dev_put() from get_pci_dev() to revert to the previous behavior. Fixes: 902bdc57 ("powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn") Cc: stable@vger.kernel.org # v4.16 Signed-off-by:
Greg Kurz <groug@kaod.org> Reviewed-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by:
-
Ravi Bangoria authored
commit f474c28f upstream. powerpc hardware triggers watchpoint before executing the instruction. To make trigger-after-execute behavior, kernel emulates the instruction. If the instruction is 'load something into non-volatile register', exception handler should restore emulated register state while returning back, otherwise there will be register state corruption. eg, adding a watchpoint on a list can corrput the list: # cat /proc/kallsyms | grep kthread_create_list c00000000121c8b8 d kthread_create_list Add watchpoint on kthread_create_list->prev: # perf record -e mem:0xc00000000121c8c0 Run some workload such that new kthread gets invoked. eg, I just logged out from console: list_add corruption. next->prev should be prev (c000000001214e00), \ but was c00000000121c8b8. (next=c00000000121c8b8). WARNING: CPU: 59 PID: 309 at lib/list_debug.c:25 __list_add_valid+0xb4/0xc0 CPU: 59 PID: 309 Comm: kworker/59:0 Kdump: loaded Not tainted 5.1.0-rc7+ #69 ... NIP __list_add_valid+0xb4/0xc0 LR __list_add_valid+0xb0/0xc0 Call Trace: __list_add_valid+0xb0/0xc0 (unreliable) __kthread_create_on_node+0xe0/0x260 kthread_create_on_node+0x34/0x50 create_worker+0xe8/0x260 worker_thread+0x444/0x560 kthread+0x160/0x1a0 ret_from_kernel_thread+0x5c/0x70 List corruption happened because it uses 'load into non-volatile register' instruction: Snippet from __kthread_create_on_node: c000000000136be8: addis r29,r2,-19 c000000000136bec: ld r29,31424(r29) if (!__list_add_valid(new, prev, next)) c000000000136bf0: mr r3,r30 c000000000136bf4: mr r5,r28 c000000000136bf8: mr r4,r29 c000000000136bfc: bl c00000000059a2f8 <__list_add_valid+0x8> Register state from WARN_ON(): GPR00: c00000000059a3a0 c000007ff23afb50 c000000001344e00 0000000000000075 GPR04: 0000000000000000 0000000000000000 0000001852af8bc1 0000000000000000 GPR08: 0000000000000001 0000000000000007 0000000000000006 00000000000004aa GPR12: 0000000000000000 c000007ffffeb080 c000000000137038 c000005ff62aaa00 GPR16: 0000000000000000 0000000000000000 c000007fffbe7600 c000007fffbe7370 GPR20: c000007fffbe7320 c000007fffbe7300 c000000001373a00 0000000000000000 GPR24: fffffffffffffef7 c00000000012e320 c000007ff23afcb0 c000000000cb8628 GPR28: c00000000121c8b8 c000000001214e00 c000007fef5b17e8 c000007fef5b17c0 Watchpoint hit at 0xc000000000136bec. addis r29,r2,-19 => r29 = 0xc000000001344e00 + (-19 << 16) => r29 = 0xc000000001214e00 ld r29,31424(r29) => r29 = *(0xc000000001214e00 + 31424) => r29 = *(0xc00000000121c8c0) 0xc00000000121c8c0 is where we placed a watchpoint and thus this instruction was emulated by emulate_step. But because handle_dabr_fault did not restore emulated register state, r29 still contains stale value in above register state. Fixes: 5aae8a53 ("powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors") Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: stable@vger.kernel.org # 2.6.36+ Signed-off-by:
-
Christophe Leroy authored
commit 6ecb78ef upstream. Previously, only IBAT1 and IBAT2 were used to map kernel linear mem. Since commit 63b2bc61 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX"), we may have all 8 BATs used for mapping kernel text. But the suspend/restore functions only save/restore BATs 0 to 3, and clears BATs 4 to 7. Make suspend and restore functions respectively save and reload the 8 BATs on CPUs having MMU_FTR_USE_HIGH_BATS feature. Reported-by:
Andreas Schwab <schwab@linux-m68k.org> Cc: stable@vger.kernel.org Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Helge Deller authored
commit 10835c85 upstream. On parisc the privilege level of a process is stored in the lowest two bits of the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0 for the kernel and privilege level 3 for user-space. So userspace should not be allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege level to e.g. 0 to try to gain kernel privileges. This patch prevents such modifications by always setting the two lowest bits to one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are modified via ptrace calls in the native and compat ptrace paths. Link: https://bugs.gentoo.org/481768Reported-by:
Jeroen Roovers <jer@gentoo.org> Cc: <stable@vger.kernel.org> Tested-by:
Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Helge Deller authored
commit 34c32fc6 upstream. On parisc the privilege level of a process is stored in the lowest two bits of the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0 for the kernel and privilege level 3 for user-space. So userspace should not be allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege level to e.g. 0 to try to gain kernel privileges. This patch prevents such modifications in the regset support functions by always setting the two lowest bits to one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are modified via ptrace regset calls. Link: https://bugs.gentoo.org/481768 Cc: <stable@vger.kernel.org> # v4.7+ Tested-by:
-
Ard Biesheuvel authored
commit ed527b13 upstream. The CAAM driver currently violates an undocumented and slightly controversial requirement imposed by the crypto stack that a buffer referred to by the request structure via its virtual address may not be modified while any scatterlists passed via the same request structure are mapped for inbound DMA. This may result in errors like alg: aead: decryption failed on test 1 for gcm_base(ctr-aes-caam,ghash-generic): ret=74 alg: aead: Failed to load transform for gcm(aes): -2 on non-cache coherent systems, due to the fact that the GCM driver passes an IV buffer by virtual address which shares a cacheline with the auth_tag buffer passed via a scatterlist, resulting in corruption of the auth_tag when the IV is updated while the DMA mapping is live. Since the IV that is returned to the caller is only valid for CBC mode, and given that the in-kernel users of CBC (such as CTS) don't trigger the same issue as the GCM driver, let's just disable the output IV generation for all modes except CBC for the time being. Fixes: 854b06f7 ("crypto: caam - properly set IV after {en,de}crypt") Cc: Horia Geanta <horia.geanta@nxp.com> Cc: Iuliana Prodan <iuliana.prodan@nxp.com> Reported-by:
Sascha Hauer <s.hauer@pengutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by:
Horia Geanta <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> [ Horia: backported to 4.14, 4.19 ] Signed-off-by:
-
Steve Longerbeam authored
commit 3d1f62c6 upstream. The saturation bit was being set at bit 9 in the second 32-bit word of the TPMEM CSC. This isn't correct, the saturation bit is bit 42, which is bit 10 of the second word. Fixes: 1aa8ea0d ("gpu: ipu-v3: Add Image Converter unit") Signed-off-by:
Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by:
-
Darrick J. Wong authored
commit 1fdeaea4 upstream. Dave Chinner noticed that xfs_file_dio_aio_write returns EAGAIN without dropping the IOLOCK when its deciding not to wait, which means that we leak the IOLOCK there. Since we now make unaligned directio always wait, we have the opportunity to bail out before trying to take the lock, which should reduce the overhead of this never-gonna-work case considerably while also solving the dropped lock problem. Reported-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Brian Foster authored
commit 2032a8a2 upstream. XFS applies more strict serialization constraints to unaligned direct writes to accommodate things like direct I/O layer zeroing, unwritten extent conversion, etc. Unaligned submissions acquire the exclusive iolock and wait for in-flight dio to complete to ensure multiple submissions do not race on the same block and cause data corruption. This generally works in the case of an aligned dio followed by an unaligned dio, but the serialization is lost if I/Os occur in the opposite order. If an unaligned write is submitted first and immediately followed by an overlapping, aligned write, the latter submits without the typical unaligned serialization barriers because there is no indication of an unaligned dio still in-flight. This can lead to unpredictable results. To provide proper unaligned dio serialization, require that such direct writes are always the only dio allowed in-flight at one time for a particular inode. We already acquire the exclusive iolock and drain pending dio before submitting the unaligned dio. Wait once more after the dio submission to hold the iolock across the I/O and prevent further submissions until the unaligned I/O completes. This is heavy handed, but consistent with the current pre-submission serialization for unaligned direct writes. Signed-off-by:
Allison Henderson <allison.henderson@oracle.com> Reviewed-by:
-
Luis R. Rodriguez authored
commit 1b9598c8 upstream. statx(2) notes that any attribute that is not indicated as supported by stx_attributes_mask has no usable value. Commit 5f955f26 ("xfs: report crtime and attribute flags to statx") added support for informing userspace of extra file attributes but forgot to list these flags as supported making reporting them rather useless for the pedantic userspace author. $ git describe --contains 5f955f26 v4.11-rc6~5^2^2~2 Fixes: 5f955f26 ("xfs: report crtime and attribute flags to statx") Signed-off-by:
-
Darrick J. Wong authored
commit 15a268d9 upstream. Log recovery frees all the inodes stored in the unlinked list, which can cause expansion of the free inode btree. The ifree code skips block reservations if it thinks there's a per-AG space reservation, but we don't set up the reservation until after log recovery, which means that a finobt expansion blows up in xfs_trans_mod_sb when we exceed the transaction's block reservation. To fix this, we set the "no finobt reservation" flag to true when we create the xfs_mount and only set it to false if we confirm that every AG had enough free space to put aside for the finobt. Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Reviewed-by:
-
Darrick J. Wong authored
commit c4a6bf7f upstream. When XFS creates an O_TMPFILE file, the inode is created with nlink = 1, put on the unlinked list, and then the VFS sets nlink = 0 in d_tmpfile. If we crash before anything logs the inode (it's dirty incore but the vfs doesn't tell us it's dirty so we never log that change), the iunlink processing part of recovery will then explode with a pile of: XFS: Assertion failed: VFS_I(ip)->i_nlink == 0, file: fs/xfs/xfs_log_recover.c, line: 5072 Worse yet, since nlink is nonzero, the inodes also don't get cleaned up and they just leak until the next xfs_repair run. Therefore, change xfs_iunlink to require that inodes being put on the unlinked list have nlink == 0, change the tmpfile callers to instantiate nodes that way, and set the nlink to 1 just prior to calling d_tmpfile. Fix the comment for xfs_iunlink while we're at it. Signed-off-by:
-
Darrick J. Wong authored
commit e1f6ca11 upstream. Rename this flag variable to imply more strongly that it's related to the free inode btree (finobt) operation. No functional changes. Signed-off-by:
-
Darrick J. Wong authored
commit 3b50086f upstream. For VFS listxattr calls, xfs_xattr_put_listent calls __xfs_xattr_put_listent twice if it sees an attribute "trusted.SGI_ACL_FILE": once for that name, and again for "system.posix_acl_access". Unfortunately, if we happen to run out of buffer space while emitting the first name, we set count to -1 (so that we can feed ERANGE to the caller). The second invocation doesn't check that the context parameters make sense and overwrites the byte before the buffer, triggering a KASAN report: ================================================================== BUG: KASAN: slab-out-of-bounds in strncpy+0xb3/0xd0 Write of size 1 at addr ffff88807fbd317f by task syz/1113 CPU: 3 PID: 1113 Comm: syz Not tainted 5.0.0-rc6-xfsx #rc6 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: dump_stack+0xcc/0x180 print_address_description+0x6c/0x23c kasan_report.cold.3+0x1c/0x35 strncpy+0xb3/0xd0 __xfs_xattr_put_listent+0x1a9/0x2c0 [xfs] xfs_attr_list_int_ilocked+0x11af/0x1800 [xfs] xfs_attr_list_int+0x20c/0x2e0 [xfs] xfs_vn_listxattr+0x225/0x320 [xfs] listxattr+0x11f/0x1b0 path_listxattr+0xbd/0x130 do_syscall_64+0x139/0x560 While we're at it we add an assert to the other put_listent to avoid this sort of thing ever happening to the attrlist_by_handle code. Signed-off-by:
-
Dave Chinner authored
commit 2c307174 upstream. On a sub-page block size filesystem, fsx is failing with a data corruption after a series of operations involving copying a file with the destination offset beyond EOF of the destination of the file: 8093(157 mod 256): TRUNCATE DOWN from 0x7a120 to 0x50000 ******WWWW 8094(158 mod 256): INSERT 0x25000 thru 0x25fff (0x1000 bytes) 8095(159 mod 256): COPY 0x18000 thru 0x1afff (0x3000 bytes) to 0x2f400 8096(160 mod 256): WRITE 0x5da00 thru 0x651ff (0x7800 bytes) HOLE 8097(161 mod 256): COPY 0x2000 thru 0x5fff (0x4000 bytes) to 0x6fc00 The second copy here is beyond EOF, and it is to sub-page (4k) but block aligned (1k) offset. The clone runs the EOF zeroing, landing in a pre-existing post-eof delalloc extent. This zeroes the post-eof extents in the page cache just fine, dirtying the pages correctly. The problem is that xfs_reflink_remap_prep() now truncates the page cache over the range that it is copying it to, and rounds that down to cover the entire start page. This removes the dirty page over the delalloc extent from the page cache without having written it back. Hence later, when the page cache is flushed, the page at offset 0x6f000 has not been written back and hence exposes stale data, which fsx trips over less than 10 operations later. Fix this by changing xfs_reflink_remap_prep() to use xfs_flush_unmap_range(). Signed-off-by:
-
Darrick J. Wong authored
commit 4918ef4e upstream. Prior to remapping blocks, it is necessary to remove pages from the destination file's page cache. Unfortunately, the truncation is not aggressive enough -- if page size > block size, we'll end up zeroing subpage blocks instead of removing them. So, round the start offset down and the end offset up to page boundaries. We already wrote all the dirty data so the larger range shouldn't be a problem. Signed-off-by:
-
