When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC

Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 92418fb1 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.

This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255.  Fix this by making i
a u16.

Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

KCSAN reported the following data-race [1]

The fix will also prevent the compiler from optimizing out
the condition.

[1]

BUG: KCSAN: data-race in neigh_resolve_output / neigh_resolve_output

write to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 1:
 neigh_event_send include/net/neighbour.h:443 [inline]
 neigh_resolve_output+0x78/0x480 net/core/neighbour.c:1474
 neigh_output include/net/neighbour.h:511 [inline]
 ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
 __ip_finish_output net/ipv4/ip_output.c:308 [inline]
 __ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
 ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
 NF_HOOK_COND include/linux/netfilter.h:294 [inline]
 ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
 dst_output include/net/dst.h:436 [inline]
 ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
 __ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
 ip_queue_xmit+0x45/0x60 include/net/ip.h:237
 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
 tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
 __tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
 tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
 tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
 tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598
 tcp_write_timer+0xd1/0xf0 net/ipv4/tcp_timer.c:618

read to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 0:
 neigh_event_send include/net/neighbour.h:442 [inline]
 neigh_resolve_output+0x57/0x480 net/core/neighbour.c:1474
 neigh_output include/net/neighbour.h:511 [inline]
 ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
 __ip_finish_output net/ipv4/ip_output.c:308 [inline]
 __ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
 ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
 NF_HOOK_COND include/linux/netfilter.h:294 [inline]
 ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
 dst_output include/net/dst.h:436 [inline]
 ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
 __ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
 ip_queue_xmit+0x45/0x60 include/net/ip.h:237
 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
 tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
 __tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
 tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
 tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
 tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "42f5cda5" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.

This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.

Fixes: 42f5cda5 ("vsock/virtio: set SOCK_DONE on peer shutdown")
Cc: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three small fixes:
 * we hit a failure path bug related to
   ieee80211_txq_setup_flows()
 * also use kvmalloc() to make that less likely
 * fix a timing value shortly after boot (during
   INITIAL_JIFFIES)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.

Fixes: 109cc165 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).

 # iw wlan0 station get fc:ec:da:64:a6:dd
 Station fc:ec:da:64:a6:dd (on wlan0)
	inactive time:	4294894049 ms
	.
	.
	connected time:	70 seconds

Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.

To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.

Fixes: 557fc4a0 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

If ieee80211_txq_setup_flows() fails, we don't clean up LED
state properly, leading to crashes later on, fix that.

Fixes: dc8b274f ("mac80211: Move up init of TXQs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20191105154110.1ccf7112ba5d.I0ba865792446d051867b33153be65ce6b063d98c@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Hendrik reported routes in the main table using source address are not
removed when the address is removed. The problem is that fib_sync_down_addr
does not account for devices in the default VRF which are associated
with the main table. Fix by updating the table id reference.

Fixes: 5a56a0b3 ("net: Don't delete routes in different VRFs")
Reported-by: Hendrik Donner <hd@os-cillation.de>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :

1) fib6_nh->last_probe has an initial value of 0.

   While probably okay on 64bit kernels, this causes an issue
   on 32bit kernels since the time_after(jiffies, 0 + interval)
   might be false ~24 days after boot (for HZ=1000)

2) The data-race found by KCSAN
   I could use READ_ONCE() and WRITE_ONCE(), but we also can
   take the opportunity of not piling-up too many rt6_probe_deferred()
   works by using instead cmpxchg() so that only one cpu wins the race.

[1]
BUG: KCSAN: data-race in find_match / find_match

write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1:
 rt6_probe net/ipv6/route.c:663 [inline]
 find_match net/ipv6/route.c:757 [inline]
 find_match+0x5bd/0x790 net/ipv6/route.c:733
 __find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
 find_rr_leaf net/ipv6/route.c:852 [inline]
 rt6_select net/ipv6/route.c:896 [inline]
 fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
 ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
 ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
 fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
 ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
 ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
 ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
 ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
 inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
 inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
 tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
 tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735

read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
 rt6_probe net/ipv6/route.c:657 [inline]
 find_match net/ipv6/route.c:757 [inline]
 find_match+0x521/0x790 net/ipv6/route.c:733
 __find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
 find_rr_leaf net/ipv6/route.c:852 [inline]
 rt6_select net/ipv6/route.c:896 [inline]
 fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
 ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
 ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
 fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
 ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
 ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
 ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
 ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
 inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
 inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
 __tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: cc3a86c8 ("ipv6: Change rt6_probe to take a fib6_nh")
Fixes: f547fac6 ("ipv6: rate-limit probes for neighbourless routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.

Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.

Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
   right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
   of the existing locks and stray code for now. This should
   solve the problem reported by Marc.

[1] https://git.kernel.org/torvalds/c/4bd2c03be7
[2] https://patchwork.ozlabs.org/patch/1189139/

Fixes: 4bd2c03b ("net: hns: remove ndo_poll_controller")
Cc: lipeng <lipeng321@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Exactly same layout as the default DW5821e module, just a different
vid/pid.

The QMI interface is exposed in USB configuration #1:

P:  Vendor=413c ProdID=81e0 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5821e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>

A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.

V2: used sizeof as request by Alexander

Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.

Fixes: 52feb444 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: d9b8d8e1 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.

Fixes: 72e2fb07 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahamees says:

====================
Mellanox, mlx5 fixes 2019-11-06

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

No -stable this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.

Fixes: a2928d28 ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: Fixes for -net

Misc fixes for stmmac.

Patch 1/11 and 2/11, use the correct variable type for bitrev32() calls.

Patch 3/11, fixes the random failures the we were seing when running selftests.

Patch 4/11, prevents a crash that can occur when receiving AVB packets and with
SPH feature enabled on XGMAC.

Patch 5/11, fixes the correct settings for CBS on XGMAC.

Patch 6/11, corrects the interpretation of AVB feature on XGMAC.

Patch 7/11, disables Flow Control for AVB enabled queues on XGMAC.

Patch 8/11, disables MMC interrupts on XGMAC, preventing a storm of interrupts.

Patch 9/11, fixes the number of packets that were being taken into account in
the RX path cleaning function.

Patch 10/11, fixes an incorrect descriptor setting that could cause IP
misbehavior.

Patch 11/11, fixes the IOC generation mechanism when multiple descriptors
are used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.

Fixes: a993db88 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.

Fix this.

Fixes: ec222003 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.

Fixes: b6cdf09f ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.

Fixes: ec6ea8e3 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.

Fixes: c2b69474 ("net: stmmac: xgmac: Correct RAVSEL field interpretation")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.

Fixes: ec6ea8e3 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.

Fixes: 67afd6d1 ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.

To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.

Fixes: 091810db ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bitrev32 function returns an u32 var, not an int. Fix it.

Fixes: 0efedbf1 ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bitrev32 function returns an u32 var, not an int. Fix it.

Fixes: 477286b5 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Missing register size validation in bitwise and cmp offloads.

2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
   from Dan Carpenter.

3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
   Stefano Brivio.

4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
   from Jozsef Kadlecsik.

5) Fix unaligned access to private data area of nf_tables instructions,
   from Lukas Wunner.

6) Relax check for object updates, reported as a regression by
   Eric Garver, patch from Fernando Fernandez Mancera.

7) Crash on ebtables dnat extension when used from the output path.
   From Florian Westphal.

8) Fix bogus EOPNOTSUPP when updating basechain flags.

9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If a pnet table entry is to be added mentioning a valid ethernet
interface, but an invalid infiniband or ISM device, the dev_put()
operation for the ethernet interface is called twice, resulting
in a negative refcount for the ethernet interface, which disables
removal of such a network interface.

This patch removes one of the dev_put() calls.

Fixes: 890a2cb4 ("net/smc: rework pnet table")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net/tls: add a TX lock

Some time ago Pooja and Mallesham started reporting crashes with
an async accelerator. After trying to poke the existing logic into
shape I came to the conclusion that it can't be trusted, and to
preserve our sanity we should just add a lock around the TX side.

First patch removes the sk_write_pending checks from the write
space callbacks. Those don't seem to have a logical justification.

Patch 2 adds the TX lock and patch 3 associated test (which should
hang with current net).

Mallesham reports that even with these fixes applied the async
accelerator workload still occasionally hangs waiting for socket
memory. I suspect that's strictly related to the way async crypto
is integrated in TLS, so I think we should get these into net or
net-next and move from there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test which spawns 16 threads and performs concurrent
send and recv calls on the same socket.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.

TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.

This has two problems:
 - writers don't wake other threads up when they leave the kernel;
   meaning that this scheme works for single extra thread (second
   application thread or delayed work) because memory becoming
   available will send a wake up request, but as Mallesham and
   Pooja report with larger number of threads it leads to threads
   being put to sleep indefinitely;
 - the delayed work does not get _scheduled_ but it may _run_ when
   other writers are present leading to crashes as writers don't
   expect state to change under their feet (same records get pushed
   and freed multiple times); it's hard to reliably bail from the
   work, however, because the mere presence of a writer does not
   guarantee that the writer will push pending records before exiting.

Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.

The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.

Fixes: a42055e8 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Mallesham  Jatharakonda <mallesh537@gmail.com>
Reported-by: Pooja Trivedi <poojatrivedi@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_write_pending being not zero does not guarantee that partial
record will be pushed. If the thread waiting for memory times out
the pending record may get stuck.

In case of tls_device there is no path where parial record is
set and writer present in the first place. Partial record is
set only in tls_push_sg() and tls_push_sg() will return an
error immediately. All tls_device callers of tls_push_sg()
will return (and not wait for memory) if it failed.

Fixes: a42055e8 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.

Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>