We shouldn't abuse exceptions: if the destination MTU is already higher
than what we're transmitting, no exception should be created.

Fixes: 52a589d5 ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff ("vxlan: update skb dst pmtu on tx path")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f15ca723 ("net: don't call update_pmtu unconditionally") avoids
that we try updating PMTU for a non-existent destination, but didn't clean
up cases where the check was already explicit. Drop those redundant checks.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to rfc7496 section 4.3 or 4.4:

   sprstat_policy:  This parameter indicates for which PR-SCTP policy
      the user wants the information.  It is an error to use
      SCTP_PR_SCTP_NONE in sprstat_policy.  If SCTP_PR_SCTP_ALL is used,
      the counters provided are aggregated over all supported policies.

We change to dump pr_assoc and pr_stream all status by SCTP_PR_SCTP_ALL
instead, and return error for SCTP_PR_SCTP_NONE, as it also said "It is
an error to use SCTP_PR_SCTP_NONE in sprstat_policy. "

Fixes: 826d253d ("sctp: add SCTP_PR_ASSOC_STATUS on sctp sockopt")
Fixes: d229d48d ("sctp: add SCTP_PR_STREAM_STATUS sockopt for prsctp")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: fix pedit set action offloads

Pieter says:

This set fixes set actions when using multiple pedit actions with
partial masks and with multiple keys per pedit action. Additionally
it fixes set ipv6 pedit action offloads when using it in combination
with other header keys.

The problem would only trigger if one combines multiple pedit actions
of the same type with partial masks, e.g.:

$ tc filter add dev netdev protocol ip parent ffff: \
    flower indev netdev \
    ip_proto tcp \
    action pedit ex munge \
    ip src set 11.11.11.11 retain 65535 munge \
    ip src set 22.22.22.22 retain 4294901760 pipe \
    csum ip and tcp pipe \
    mirred egress redirect dev netdev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously when populating the set ipv6 address action, we incorrectly
made use of pedit's key index to determine which 32bit word should be
set. We now calculate which word has been selected based on the offset
provided by the pedit action.

Fixes: 354b82bb ("nfp: add set ipv6 source and destination address")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we only allowed a single header key per pedit action to
change the header. This used to result in the last header key in the
pedit action to overwrite previous headers. We now keep track of them
and allow multiple header keys per pedit action.

Fixes: c0b1bd9a ("nfp: add set ipv4 header action flower offload")
Fixes: 354b82bb ("nfp: add set ipv6 source and destination address")
Fixes: f8b7b0a6 ("nfp: add set tcp and udp header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we did not correctly change headers when using multiple
pedit actions with partial masks. We now take this into account and
no longer just commit the last pedit action.

Fixes: c0b1bd9a ("nfp: add set ipv4 header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a missing call to rxrpc_put_peer() on the main path through the
rxrpc_error_report() function.  This manifests itself as a ref leak
whenever an ICMP packet or other error comes in.

In commit f3344303, the hand-off of the ref to a work item was removed
and was not replaced with a put.

Fixes: f3344303 ("rxrpc: Fix error distribution")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Other than asoc pmtu sync from all transports, sctp_assoc_sync_pmtu
is also processing transport pmtu_pending by icmp packets. But it's
meaningless to use sctp_dst_mtu(t->dst) as new pmtu for a transport.

The right pmtu value should come from the icmp packet, and it would
be saved into transport->mtu_info in this patch and used later when
the pmtu sync happens in sctp_sendmsg_to_asoc or sctp_packet_config.

Besides, without this patch, as pmtu can only be updated correctly
when receiving a icmp packet and no place is holding sock lock, it
will take long time if the sock is busy with sending packets.

Note that it doesn't process transport->mtu_info in .release_cb(),
as there is no enough information for pmtu update, like for which
asoc or transport. It is not worth traversing all asocs to check
pmtu_pending. So unlike tcp, sctp does this in tx path, for which
mtu_info needs to be atomic_t.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit db65f35f ("net: fec: add support of ethtool get_regs") introduce
ethool "--register-dump" interface to dump all FEC registers.

But not all silicon implementations of the Freescale FEC hardware module
have the FRBR (FIFO Receive Bound Register) and FRSR (FIFO Receive Start
Register) register, so we should not be trying to dump them on those that
don't.

To fix it we create a quirk flag, FEC_QUIRK_HAS_RFREG, and check it before
dump those RX FIFO registers.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in DP_INFO message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot found a use-after-free in inet6_mc_check [1]

The problem here is that inet6_mc_check() uses rcu
and read_lock(&iml->sflock)

So the fact that ip6_mc_leave_src() is called under RTNL
and the socket lock does not help us, we need to acquire
iml->sflock in write mode.

In the future, we should convert all this stuff to RCU.

[1]
BUG: KASAN: use-after-free in ipv6_addr_equal include/net/ipv6.h:521 [inline]
BUG: KASAN: use-after-free in inet6_mc_check+0xae7/0xb40 net/ipv6/mcast.c:649
Read of size 8 at addr ffff8801ce7f2510 by task syz-executor0/22432

CPU: 1 PID: 22432 Comm: syz-executor0 Not tainted 4.19.0-rc7+ #280
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
 print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
 ipv6_addr_equal include/net/ipv6.h:521 [inline]
 inet6_mc_check+0xae7/0xb40 net/ipv6/mcast.c:649
 __raw_v6_lookup+0x320/0x3f0 net/ipv6/raw.c:98
 ipv6_raw_deliver net/ipv6/raw.c:183 [inline]
 raw6_local_deliver+0x3d3/0xcb0 net/ipv6/raw.c:240
 ip6_input_finish+0x467/0x1aa0 net/ipv6/ip6_input.c:345
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:426
 ip6_mc_input+0x48a/0xd20 net/ipv6/ip6_input.c:503
 dst_input include/net/dst.h:450 [inline]
 ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ipv6_rcv+0x120/0x640 net/ipv6/ip6_input.c:271
 __netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4913
 __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5023
 netif_receive_skb_internal+0x12c/0x620 net/core/dev.c:5126
 napi_frags_finish net/core/dev.c:5664 [inline]
 napi_gro_frags+0x75a/0xc90 net/core/dev.c:5737
 tun_get_user+0x3189/0x4250 drivers/net/tun.c:1923
 tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:1968
 call_write_iter include/linux/fs.h:1808 [inline]
 do_iter_readv_writev+0x8b0/0xa80 fs/read_write.c:680
 do_iter_write+0x185/0x5f0 fs/read_write.c:959
 vfs_writev+0x1f1/0x360 fs/read_write.c:1004
 do_writev+0x11a/0x310 fs/read_write.c:1039
 __do_sys_writev fs/read_write.c:1112 [inline]
 __se_sys_writev fs/read_write.c:1109 [inline]
 __x64_sys_writev+0x75/0xb0 fs/read_write.c:1109
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457421
Code: 75 14 b8 14 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 34 b5 fb ff c3 48 83 ec 08 e8 1a 2d 00 00 48 89 04 24 b8 14 00 00 00 0f 05 <48> 8b 3c 24 48 89 c2 e8 63 2d 00 00 48 89 d0 48 83 c4 08 48 3d 01
RSP: 002b:00007f2d30ecaba0 EFLAGS: 00000293 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 000000000000003e RCX: 0000000000457421
RDX: 0000000000000001 RSI: 00007f2d30ecabf0 RDI: 00000000000000f0
RBP: 0000000020000500 R08: 00000000000000f0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 00007f2d30ecb6d4
R13: 00000000004c4890 R14: 00000000004d7b90 R15: 00000000ffffffff

Allocated by task 22437:
 save_stack+0x43/0xd0 mm/kasan/kasan.c:448
 set_track mm/kasan/kasan.c:460 [inline]
 kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
 __do_kmalloc mm/slab.c:3718 [inline]
 __kmalloc+0x14e/0x760 mm/slab.c:3727
 kmalloc include/linux/slab.h:518 [inline]
 sock_kmalloc+0x15a/0x1f0 net/core/sock.c:1983
 ip6_mc_source+0x14dd/0x1960 net/ipv6/mcast.c:427
 do_ipv6_setsockopt.isra.9+0x3afb/0x45d0 net/ipv6/ipv6_sockglue.c:743
 ipv6_setsockopt+0xbd/0x170 net/ipv6/ipv6_sockglue.c:933
 rawv6_setsockopt+0x59/0x140 net/ipv6/raw.c:1069
 sock_common_setsockopt+0x9a/0xe0 net/core/sock.c:3038
 __sys_setsockopt+0x1ba/0x3c0 net/socket.c:1902
 __do_sys_setsockopt net/socket.c:1913 [inline]
 __se_sys_setsockopt net/socket.c:1910 [inline]
 __x64_sys_setsockopt+0xbe/0x150 net/socket.c:1910
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 22430:
 save_stack+0x43/0xd0 mm/kasan/kasan.c:448
 set_track mm/kasan/kasan.c:460 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
 kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
 __cache_free mm/slab.c:3498 [inline]
 kfree+0xcf/0x230 mm/slab.c:3813
 __sock_kfree_s net/core/sock.c:2004 [inline]
 sock_kfree_s+0x29/0x60 net/core/sock.c:2010
 ip6_mc_leave_src+0x11a/0x1d0 net/ipv6/mcast.c:2448
 __ipv6_sock_mc_close+0x20b/0x4e0 net/ipv6/mcast.c:310
 ipv6_sock_mc_close+0x158/0x1d0 net/ipv6/mcast.c:328
 inet6_release+0x40/0x70 net/ipv6/af_inet6.c:452
 __sock_release+0xd7/0x250 net/socket.c:579
 sock_close+0x19/0x20 net/socket.c:1141
 __fput+0x385/0xa30 fs/file_table.c:278
 ____fput+0x15/0x20 fs/file_table.c:309
 task_work_run+0x1e8/0x2a0 kernel/task_work.c:113
 tracehook_notify_resume include/linux/tracehook.h:193 [inline]
 exit_to_usermode_loop+0x318/0x380 arch/x86/entry/common.c:166
 prepare_exit_to_usermode arch/x86/entry/common.c:197 [inline]
 syscall_return_slowpath arch/x86/entry/common.c:268 [inline]
 do_syscall_64+0x6be/0x820 arch/x86/entry/common.c:293
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8801ce7f2500
 which belongs to the cache kmalloc-192 of size 192
The buggy address is located 16 bytes inside of
 192-byte region [ffff8801ce7f2500, ffff8801ce7f25c0)
The buggy address belongs to the page:
page:ffffea000739fc80 count:1 mapcount:0 mapping:ffff8801da800040 index:0x0
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffffea0006f6e548 ffffea000737b948 ffff8801da800040
raw: 0000000000000000 ffff8801ce7f2000 0000000100000010 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8801ce7f2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8801ce7f2480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8801ce7f2500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                         ^
 ffff8801ce7f2580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
 ffff8801ce7f2600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The binding table's 'cluster_scope' list is rcu protected to handle
races between threads changing the list and those traversing the list at
the same moment. We have now found that the function named_distribute()
uses the regular list_for_each() macro to traverse the said list.
Likewise, the function tipc_named_withdraw() is removing items from the
same list using the regular list_del() call. When these two functions
execute in parallel we see occasional crashes.

This commit fixes this by adding the missing _rcu() suffixes.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The udpv6_encap_enable() function is part of the ipv6 code, and if that is
configured as a loadable module and rxrpc is built in then a build failure
will occur because the conditional check is wrong:

  net/rxrpc/local_object.o: In function `rxrpc_lookup_local':
  local_object.c:(.text+0x2688): undefined reference to `udpv6_encap_enable'

Use the correct config symbol (CONFIG_AF_RXRPC_IPV6) in the conditional
check rather than CONFIG_IPV6 as that will do the right thing.

Fixes: 5271953c ("rxrpc: Use the UDP encap_rcv hook")
Reported-by: kbuild-all@01.org
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When commit 27097255 ("[IPV6]: ROUTE: Add Router Reachability
Probing (RFC4191).") introduced router probing, the rt6_probe() function
required that a neighbour entry existed. This neighbour entry is used to
record the timestamp of the last probe via the ->updated field.

Later, commit 2152caea ("ipv6: Do not depend on rt->n in rt6_probe().")
removed the requirement for a neighbour entry. Neighbourless routes skip
the interval check and are not rate-limited.

This patch adds rate-limiting for neighbourless routes, by recording the
timestamp of the last probe in the fib6_info itself.

Fixes: 2152caea ("ipv6: Do not depend on rt->n in rt6_probe().")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.

Fixes: 42138085 ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

net/rxrpc/output.c: In function 'rxrpc_reject_packets':
net/rxrpc/output.c:527:11: warning:
 variable 'ioc' set but not used [-Wunused-but-set-variable]

'ioc' is the correct kvec num when sending a BUSY (or an ABORT) response
packet.

Fixes: ece64fec ("rxrpc: Emit BUSY packets when supposed to rather than ABORTs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix an uninitialised variable introduced by the last patch.  This can cause
a crash when a new call comes in to a local service, such as when an AFS
fileserver calls back to the local cache manager.

Fixes: c1e15b49 ("rxrpc: Fix the packet reception routine")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
unicast links to the affected node.

Unfortunately, this 'improvement' introduced two bugs, which each and
one alone cause only limited problems, but combined lead to seemingly
stochastic unicast link resets, depending on the amount of broadcast
traffic transmitted.

The first issue, a missing initialization of the 'tolerance' field of
the receiver broadcast link, was recently fixed by commit 047491ea
("tipc: set link tolerance correctly in broadcast link").

Ths second issue, where we omit to reset the 'stale_cnt' field of
the same link after a 'stale' period is over, leads to this counter
accumulating over time, and in the absence of the 'tolerance' criteria
leads to the above described symptoms. This commit adds the missing
initialization.

Fixes: a4dc70d4 ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WHen an llc sock is added into the sk_laddr_hash of an llc_sap,
it is not marked with SOCK_RCU_FREE.

This causes that the sock could be freed while it is still being
read by __llc_lookup_established() with RCU read lock. sock is
refcounted, but with RCU read lock, nothing prevents the readers
getting a zero refcnt.

Fix it by setting SOCK_RCU_FREE in llc_sap_add_socket().

Reported-by: syzbot+11e05f04c15e03be5254@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-10-10

This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.

For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Similarly to what has been done in 8b4c3cdd ("net: sched: Add policy
validation for tc attributes"), fix classifier code to add validation of
TCA_CHAIN and TCA_KIND netlink attributes.

tested with:
 # ./tdc.py -c filter

v2: Let sch_api and cls_api share nla_policy they have in common, thanks
    to David Ahern.
v3: Avoid EXPORT_SYMBOL(), as validation of those attributes is not done
    by TC modules, thanks to Cong Wang.
    While at it, restore the 'Delete / get qdisc' comment to its orginal
    position, just above tc_get_qdisc() function prototype.

Fixes: 5bc17018 ("net: sched: introduce multichain support for filters")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.

This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.

Fixes: f38d138a ("net/ethtool: support set coalesce per queue")
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ethtool_get_rxnfc(), the eth command 'cmd' is compared against
'ETHTOOL_GRXFH' to see whether it is necessary to adjust the variable
'info_size'. Then the whole structure of 'info' is copied from the
user-space buffer 'useraddr' with 'info_size' bytes. In the following
execution, 'info' may be copied again from the buffer 'useraddr' depending
on the 'cmd' and the 'info.flow_type'. However, after these two copies,
there is no check between 'cmd' and 'info.cmd'. In fact, 'cmd' is also
copied from the buffer 'useraddr' in dev_ethtool(), which is the caller
function of ethtool_get_rxnfc(). Given that 'useraddr' is in the user
space, a malicious user can race to change the eth command in the buffer
between these copies. By doing so, the attacker can supply inconsistent
data and cause undefined behavior because in the following execution 'info'
will be passed to ops->get_rxnfc().

This patch adds a necessary check on 'info.cmd' and 'cmd' to confirm that
they are still same after the two copies in ethtool_get_rxnfc(). Otherwise,
an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
	Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
	Flags: bus master, fast devsel, latency 0, IRQ 16
	I/O ports at e000 [size=256]
	Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
	Memory at e0000000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Endpoint, MSI 01
	Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
	Capabilities: [d0] Vital Product Data
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
	Capabilities: [170] Latency Tolerance Reporting
	Kernel driver in use: r8169
	Kernel modules: r8169

We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes.  That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.

However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes.  It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.

After apply the patch, the ethernet adapter works fine before suspend
and after resume.  So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.

This patch reverts commit 7bb05b85
"r8169: don't use MSI-X on RTL8106e".

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85 ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-10-14

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix xsk map update and delete operation to not call synchronize_net()
   but to piggy back on SOCK_RCU_FREE for sockets instead as we are not
   allowed to sleep under RCU, from Björn.

2) Do not change RLIMIT_MEMLOCK in reuseport_bpf selftest if the process
   already has unlimited RLIMIT_MEMLOCK, from Eric.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Arnd writes:
  "ARM: SoC fixes for 4.19

   Two last minute bugfixes, both for NXP platforms:

   * The Layerscape 'qbman' infrastructure suffers from probe ordering
     bugs in some configurations, a two-patch series adds a hotfix for
     this. 4.20 will have a longer set of patches to rework it.

   * The old imx53-qsb board regressed in 4.19 after the addition
     of cpufreq support, adding a set of explicit operating points
     fixes this."

* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  soc: fsl: qman_portals: defer probe after qman's probe
  soc: fsl: qbman: add APIs to retrieve the probing status
  ARM: dts: imx53-qsb: disable 1.2GHz OPP

Fix a leak of afs_server structs.  The routine that installs them in the
various lookup lists and trees gets a ref on leaving the function, whether
it added the server or a server already exists.  It shouldn't increment
the refcount if it added the server.

The effect of this that "rmmod kafs" will hang waiting for the leaked
server to become unused.

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just drop the "linux" part of the path, it was never correct.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 256ac037 ("dt-bindings: document devicetree bindings for mux-controllers and gpio-mux")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The file is GPL v2 or later.
Acked-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Access to the list of cells by /proc/net/afs/cells has a couple of
problems:

 (1) It should be checking against SEQ_START_TOKEN for the keying the
     header line.

 (2) It's only holding the RCU read lock, so it can't just walk over the
     list without following the proper RCU methods.

Fix these by using an hlist instead of an ordinary list and using the
appropriate accessor functions to follow it with RCU.

Since the code that adds a cell to the list must also necessarily change,
sort the list on insertion whilst we're at it.

Fixes: 989782dc ("afs: Overhaul cell database management")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ulf writes:
   "MMC core:
    - Avoid fragile multiblock reads for the last sector in SPI mode
    WIFI/SDIO:
    - libertas: Fixup suspend sequence for the SDIO card"

* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  libertas: call into generic suspend code before turning off power
  mmc: block: avoid multiblock reads for the last sector in SPI mode

Linus writes:
  "GPIO fix for the v4.19 series:
   - Fix up the interrupt parent for the irqdomains."

* tag 'gpio-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: Assign gpio_irq_chip::parents to non-stack pointer

Linus writes:
  "pin control fix for v4.19:

   A single pin control fix for v4.19:
   - Interrupt setup in the MCP23S08 driver."

* tag 'pinctrl-v4.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: mcp23s08: fix irq and irqchip setup order

Boris writes:
  "mdt: fix for 4.19-rc8

   * Fix a stack overflow in lib/bch.c"

* tag 'mtd/fixes-for-4.19-rc8' of git://git.infradead.org/linux-mtd:
  lib/bch: fix possible stack overrun

Dave writes:
  "drm fixes for 4.19-rc8

   single nouveau runtime reference and mst change"

* tag 'drm-fixes-2018-10-12-1' of git://anongit.freedesktop.org/drm/drm:
  drm/nouveau/drm/nouveau: Grab runtime PM ref in nv50_mstc_detect()

Doug writes:
  "RDMA fixes:

   Final for-rc pull request for 4.19

   We only have one bug to submit this time around.  It fixes a DMA
   unmap issue where we unmapped the DMA address from the IOMMU before
   we did from the card, resulting in a DMAR error with IOMMU enabled,
   or possible crash without."

* tag 'for-gkh' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/mlx5: Unmap DMA addr from HCA before IOMMU

Dmitry writes:
  "Input updates for v4.19-rc7

   - we added a few scheduling points into various input interfaces to
     ensure that large writes will not cause RCU stalls
   - fixed configuring PS/2 keyboards as wakeup devices on newer
     platforms
   - added a new Xbox gamepad ID."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: uinput - add a schedule point in uinput_inject_events()
  Input: evdev - add a schedule point in evdev_write()
  Input: mousedev - add a schedule point in mousedev_write()
  Input: i8042 - enable keyboard wakeups by default when s2idle is used
  Input: xpad - add support for Xbox1 PDP Camo series gamepad

Stephen writes:
  "A couple of warning fixes:

  Two fixes from Peter Oberparleiter <oberpar@linux.ibm.com>:
    Commit 6b7dca40 ("tracing: Allow gcov profiling on only ftrace subsystem")
   uncovered linker problems when using gcov kernel profiling on some
   architectures. These problems were likely introduced earlier, and are
   possibly related to compiler changes."

* tag 'next-fixes-20181012' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
  vmlinux.lds.h: Fix linker warnings about orphan .LPBX sections
  vmlinux.lds.h: Fix incomplete .text.exit discards

The previous patch introduced very large kernel stack usage and a Makefile
change to hide the warning about it.

From what I can tell, a number of things went wrong here:

- The BCH_MAX_T constant was set to the maximum value for 'n',
  not the maximum for 't', which is much smaller.

- The stack usage is actually larger than the entire kernel stack
  on some architectures that can use 4KB stacks (m68k, sh, c6x), which
  leads to an immediate overrun.

- The justification in the patch description claimed that nothing
  changed, however that is not the case even without the two points above:
  the configuration is machine specific, and most boards  never use the
  maximum BCH_ECC_WORDS() length but instead have something much smaller.
  That maximum would only apply to machines that use both the maximum
  block size and the maximum ECC strength.

The largest value for 't' that I could find is '32', which in turn leads
to a 60 byte array instead of 2048 bytes. Making it '64' for future
extension seems also worthwhile, with 120 bytes for the array. Anything
larger won't fit into the OOB area on NAND flash.

With that changed, the warning can be enabled again.

Only linux-4.19+ contains the breakage, so this is only needed
as a stable backport if it does not make it into the release.

Fixes: 02361bc7 ("lib/bch: Remove VLA usage")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>