Up to now reading the stolen time of a remote cpu was not possible in a
performant way under Xen. This made support of runqueue steal time via
paravirt_steal_rq_enabled impossible.

With the addition of an appropriate hypervisor interface this is now
possible, so add the support.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Add support for the Xen HYPERVISOR_vm_assist hypercall.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Update some Xen headers to be able to use new functionality.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

req_start is simply an alias of the "offset" function parameter, and
req_end is being used just once in each function. (And both variables
were loop invariant anyway, so should at least have got initialized
outside the loop.)
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

There's no point calling xen_pcibk_config_read() here - all it'll do is
return whatever conf_space_read() returns for the field which was found
here (and which would be found there again). Also there's no point
clearing tmp_val before the call.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Other than for raw BAR values, flags are properly separated in the
internal representation.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

It is now identical to bar_init().
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

The kernel.h macro DIV_ROUND_UP performs the computation
(((n) + (d) - 1) /(d)) but is perhaps more readable.

The Coccinelle script used to make this change is as follows:
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

System workqueues have been able to handle high level of concurrency
for a long time now and there's no reason to use dedicated workqueues
just to gain concurrency.  Replace dedicated xenbus_frontend_wq with the
use of system_wq.

Unlike a dedicated per-cpu workqueue created with create_workqueue(),
system_wq allows multiple work items to overlap executions even on
the same CPU; however, a per-cpu workqueue doesn't have any CPU
locality or global ordering guarantees unless the target CPU is
explicitly specified and the increase of local concurrency shouldn't
make any difference.

In this case, there is only a single work item, increase of concurrency
level by switching to system_wq should not make any difference.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

System workqueues have been able to handle high level of concurrency
for a long time now and there's no reason to use dedicated workqueues
just to gain concurrency.  Replace dedicated xen_pcibk_wq with the
use of system_wq.

Unlike a dedicated per-cpu workqueue created with create_workqueue(),
system_wq allows multiple work items to overlap executions even on
the same CPU; however, a per-cpu workqueue doesn't have any CPU
locality or global ordering guarantees unless the target CPU is
explicitly specified and thus the increase of local concurrency shouldn't
make any difference.

Since the work items could be pending, flush_work() has been used in
xen_pcibk_disconnect(). xen_pcibk_xenbus_remove() calls free_pdev()
which in turn calls xen_pcibk_disconnect() for every pdev to ensure that
there is no pending task while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

This will match how PMU errors are reported at check_hw_exists()'s
msr_fail label, which is reached when VPMU initialzation fails.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

The pv_time_ops structure contains a function pointer for the
"steal_clock" functionality used only by KVM and Xen on ARM. Xen on x86
uses its own mechanism to account for the "stolen" time a thread wasn't
able to run due to hypervisor scheduling.

Add support in Xen arch independent time handling for this feature by
moving it out of the arm arch into drivers/xen and remove the x86 Xen
hack.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Replace explicit computation of vma page count by a call to
vma_pages().
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

The EFI DT parameters for bare metal are located under /chosen node,
while for Xen Dom0 they are located under /hyperviosr/uefi node. These
parameters under /chosen and /hyperviosr/uefi are not expected to appear
at the same time.

Parse these EFI parameters and initialize EFI like the way for bare
metal except the runtime services because the runtime services for Xen
Dom0 are available through hypercalls and they are always enabled. So it
sets the EFI_RUNTIME_SERVICES flag if it finds /hyperviosr/uefi node and
bails out in arm_enable_runtime_services() when EFI_RUNTIME_SERVICES
flag is set already.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>

Sometimes it needs to check if there is a subnode of given node in FDT
by given name. Introduce this helper to get the subnode if it exists.

CC: Rob Herring <robh@kernel.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Julien Grall <julien.grall@arm.com>

When running on Xen hypervisor, runtime services are supported through
hypercall. Add a Xen specific function to initialize runtime services.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>

Move x86 specific codes to architecture directory and export those EFI
runtime service functions. This will be useful for initializing runtime
service on ARM later.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>

Add a "uefi" node under /hypervisor node in FDT, then Linux kernel could
scan this to get the UEFI information.

CC: Rob Herring <robh@kernel.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Move xen_early_init() before efi_init(), then when calling efi_init()
could initialize Xen specific UEFI.

Check if it runs on Xen hypervisor through the flat dts.

Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>

The kernel will get the event-channel IRQ through
HVM_PARAM_CALLBACK_IRQ.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

This new delivery type which is for ARM shares the same value with
HVM_PARAM_CALLBACK_TYPE_VECTOR which is for x86.

val[15:8] is flag: val[7:0] is a PPI.
To the flag, bit 8 stands the interrupt mode is edge(1) or level(0) and
bit 9 stands the interrupt polarity is active low(1) or high(0).
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Sync the changes of HVM_PARAM_CALLBACK_VIA ABI introduced by
Xen commit <ca5c54b6ff05> (public/hvm: export the HVM_PARAM_CALLBACK_VIA
ABI in the API).
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Add a bus_notifier for AMBA bus device in order to map the device
mmio regions when DOM0 booting with ACPI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Add a bus_notifier for platform bus device in order to map the device
mmio regions when DOM0 booting with ACPI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Add a new type of Xen map space for Dom0 to map device's MMIO region.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Use xen_xlate_map_ballooned_pages to setup grant table. Then it doesn't
rely on DT or ACPI to pass the start address and size of grant table.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Make xen_xlate_map_ballooned_pages work with 64K pages. In that case
Kernel pages are 64K in size but Xen pages remain 4K in size. Xen pfns
refer to 4K pages.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

Move xlated_setup_gnttab_pages to common place, so it can be reused by
ARM to setup grant table.

Rename it to xen_xlate_map_ballooned_pages.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>

ACPI 6.0 introduces a new table STAO to list the devices which are used
by Xen and can't be used by Dom0. On Xen virtual platforms, the physical
UART is used by Xen. So here it hides UART from Dom0.

CC: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
CC: Len Brown <lenb@kernel.org> (supporter:ACPI)
CC: linux-acpi@vger.kernel.org (open list:ACPI)
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull fuse fix from Miklos Szeredi:
 "This makes sure userspace filesystems are not broken by the parallel
  lookups and readdir feature"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: serialize dirops by default

Pull overlayfs fixes from Miklos Szeredi:
 "This contains fixes for a dentry leak, a regression in 4.6 noticed by
  Docker users and missing write access checking in truncate"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: warn instead of error if d_type is not supported
  ovl: get_write_access() in truncate
  ovl: fix dentry leak for default_permissions

overlay needs underlying fs to support d_type. Recently I put in a
patch in to detect this condition and started failing mount if
underlying fs did not support d_type.

But this breaks existing configurations over kernel upgrade. Those who
are running docker (partially broken configuration) with xfs not
supporting d_type, are surprised that after kernel upgrade docker does
not run anymore.

https://github.com/docker/docker/issues/22937#issuecomment-229881315

So instead of erroring out, detect broken configuration and warn
about it. This should allow existing docker setups to continue
working after kernel upgrade.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 45aebeaf ("ovl: Ensure upper filesystem supports d_type")
Cc: <stable@vger.kernel.org> 4.6

Pull MIPS fix from Ralf Baechle:
 "Only a single fix for 4.7 pending at this point.  It fixes an issue
  that may lead to corruption of the cache mode bits in the page table"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix possible corruption of cache mode by mprotect.

Pull powerpc fixes from Michael Ellerman:

 - tm: Always reclaim in start_thread() for exec() class syscalls from
   Cyril Bur

 - tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0 from Michael
   Neuling

 - eeh: Fix wrong argument passed to eeh_rmv_device() from Gavin Shan

 - Initialise pci_io_base as early as possible from Darren Stevens

* tag 'powerpc-4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Initialise pci_io_base as early as possible
  powerpc/tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0
  powerpc/eeh: Fix wrong argument passed to eeh_rmv_device()
  powerpc/tm: Always reclaim in start_thread() for exec() class syscalls

Pull drm fixes frlm Dave Airlie:
 "Just some AMD and Intel fixes, the AMD ones are further production
  Polaris fixes, and the Intel ones fix some early timeouts, some PCI ID
  changes and a couple of other fixes.

  Still a bit Internet challenged here, hopefully end of next week will
  solve it"

* tag 'drm-fixes-for-v4.7-rc6' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Fix missing unlock on error in i915_ppgtt_info()
  drm/amd/powerplay: workaround for UVD clock issue
  drm/amdgpu: add ACLK_CNTL setting for polaris10
  drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
  drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
  drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
  drm/i915: Add more Kabylake PCI IDs.
  drm/i915: Avoid early timeout during AUX transfers
  drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
  drm/i915/lpt: Avoid early timeout during FDI PHY reset
  drm/i915/bxt: Avoid early timeout during PLL enable
  drm/i915: Refresh cached DP port register value on resume
  drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
  drm/amd/powerplay: disable FFC.
  drm/amd/powerplay: add some definition for FFC feature on polaris.

Pull spi fixes from Mark Brown:
 "A few small driver-specific fixes for SPI, all in the normal important
  if you hit them category especially the rockchip driver fix which
  addresses a race which has been exposed more frequently with some
  recent performance improvements"

* tag 'spi-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sunxi: fix transfer timeout
  spi: sun4i: fix FIFO limit
  spi: rockchip: Signal unfinished DMA transfers
  spi: spi-ti-qspi: Suspend the queue before removing the device