There exist duplicated macro definitions in rtl8150.c, remove them.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rionet_active is allocated from the page allocator and the allocation
order is calculated on the assumption that the page size is 4KB, so it
wastes memory on more than 4K page systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug appeared in a384a33b
("via-rhine: RHINE_WAIT_FOR macro removal). It can be noticed
during suspend/resume.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Lv <DavidLv@viatech.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

In IPv4, if an RTA_IIF attribute is specified within an RTM_GETROUTE
message, then a route is searched as if a packet was received on the
specified 'iif' interface.

However in IPv6, RTA_IIF is not interpreted in the same way:
'inet6_rtm_getroute()' always calls 'ip6_route_output()', regardless the
RTA_IIF attribute.

As a result, in IPv6 there's no way to use RTM_GETROUTE in order to look
for a route as if a packet was received on a specific interface.

Fix 'inet6_rtm_getroute()' so that RTA_IIF is interpreted as "lookup a
route as if a packet was received on the specified interface", similar
to IPv4's 'inet_rtm_getroute()' interpretation.
Reported-by: Ami Koren <amikoren@yahoo.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been
renamed to eth_hw_addr_random(). This patch fixes it also in the new driver
lpc_eth.c.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If both addresses equal, nothing needs to be done. If the device is down,
then we simply copy the new address to dev->dev_addr. If the device is up,
then we add another loopback device with the new address, and if that does
not fail, we remove the loopback device with the old address. And only
then, we update the dev->dev_addr.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An infinite loop occurred if garp_attr_create was called with the values
of an existing attribute. This might happen if a previous leave request
for the attribute has not yet been followed by a PDU transmission (or,
if the application previously issued a join request for the attribute
and is now issuing another one, without having issued a leave request).

If garp_attr_create finds an existing attribute having the same values,
return the address to it. Its state will then get updated (i.e., if it
was in a leaving state, it will move into a non-leaving state and not
get deleted during the next PDU transmission).

To accomplish this fix, collapse garp_attr_insert into garp_attr_create
(which is its only caller).

Thanks to Jorge Boncompte [DTI2] <jorge@dti2.net> for contributing to
this fix.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When K >= 0xFFFF0000, AND needs the two least significant bytes of K as
its operand, but EMIT2() gives it the least significant byte of K and
0x2. EMIT() should be used here to replace EMIT2().
Signed-off-by: Feiran Zhuang  <zhuangfeiran@ict.ac.cn>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.

Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.

How to reproduce this bug ?

                       -----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24  \--|-- eth1-/                       |
                       --------------------------------

1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1

then eth0 is the active slave, and MAC of bond0 is MAC of eth0.

2 on hostA, ping 192.168.100.2

3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.

4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever the station informs the AP that it is about to leave the
operating channel, the timestamp should be recorded. It is handled
in scan resume but not in scan start. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add myself as maintainer as suggested by Stanislaw Gruszka.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With flag 'GFP_ATOMIC', probability of allocation failure is more.
Add error handling after kmalloc() call to avoid null dereference.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix comment as well.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While investigating another bug, I found that the code on the incoming path
in __netif_receive_skb will only set skb->skb_iif if it is already 0.  When
dev_forward_skb() is used in the case of interfaces like veth, skb_iif may
already have been set.  Making dev_forward_skb() cause the packet to look
like a newly received packet would seem to the the correct behaviour here,
as otherwise the wrong incoming interface can be reported for such a packet.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1.  Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest.  This lead to the wrong network namespace
being picked up by sockets (like ICMP).  Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While it is desirable to rate limit certain messages, it is not
desirable to rate limit the incrementing of counters associated
with those messages.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the driver version number to better match version of out of tree
driver that has similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This was pointed out to me by Xiaojun Zhang on Source Forge.

CC: Xiaojun Zhang <zhangxiaojun@sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.

The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now skb_add_rx_frag() has a truesize parameter, we can fix cdc-phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now skb_add_rx_frag() has a truesize parameter, we can fix f_phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HZ is more likely to be 1000 these days.

timer handlers are run from softirq, no need to disable bh

skb priority 1 is TC_PRIO_FILLER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two channels here.  User space starts counting channels at one
but in the kernel we start at zero.  If the user passes in a zero
channel that's invalid and could lead to memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the bug that may prevent from mac to be configured,
while there is an empty slot for it.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add define of SH7734 register and sh_eth_reset_hw_crc function.

V3: Rebase net/HEAD.
V2: Do not split line of #if defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This way the USB variant of the driver uses usb_make_path in order to
provide bus-info compatible to other USB drivers (like e.g. asix.c).
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".

Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:
 1) Name string overrun fix in gianfar driver from Joe Perches.

 2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El

 3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso.

 4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso.

 5) Add a parameter to skb_add_rx_frag() so we can fix the truesize
    adjustments in the drivers that use it.  The individual drivers
    aren't fixed by this commit, but will be dealt with using follow-on
    commits.  From Eric Dumazet.

 6) Add some device IDs to qmi_wwan driver, from Andrew Bird.

 7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node().  From
    Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: fix a potential rcu_read_lock() imbalance in rt6_fill_node()
  net: add a truesize parameter to skb_add_rx_frag()
  gianfar: Fix possible overrun and simplify interrupt name field creation
  USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces
  USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces
  USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces
  qlcnic: Bug fix for LRO
  netfilter: nf_conntrack: permanently attach timeout policy to conntrack
  netfilter: xt_CT: fix assignation of the generic protocol tracker
  netfilter: xt_CT: missing rcu_read_lock section in timeout assignment
  netfilter: cttimeout: fix dependency with l4protocol conntrack module
  netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6
  vhost: fix release path lockdep checks
  vhost: don't forget to schedule()
  tools/virtio: stub out strong barriers
  tools/virtio: add linux/hrtimer.h stub
  tools/virtio: add linux/module.h stub

Pull "ARM: device tree work" from Arnd Bergmann:
 "Most of these patches convert code from using static platform data to
  describing the hardware in the device tree.  This is only the first
  half of the changes for v3.4 because a lot of patches for this topic
  came in the last week before the merge window.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
  Document: devicetree: add OF documents for arch-mmp
  ARM: dts: append DTS file of pxa168
  ARM: mmp: append OF support on pxa168
  ARM: mmp: enable rtc clk in pxa168
  i2c: pxa: add OF support
  serial: pxa: add OF support
  arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
  ARM: OMAP2+: Remove extra ifdefs for board-generic
  ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
  ASoC: DT: Add digital microphone binding to PAZ00 board.
  ARM: dt: Add ARM PMU to tegra*.dtsi
  ARM: at91: at91sam9x5cm/dt: add leds support
  ARM: at91: usb_a9g20/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add leds support
  ARM: at91: usb_a9g20/dt: add leds support
  ARM: at91/pio: add new PIO3 features
  ARM: at91: add sam9_smc.o to at91sam9x5 build
  ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
  ARM: at91/tc: add device tree support to atmel_tclib
  ...

Pull "ARM: driver specific updates" from Arnd Bergmann:
 "These are all specific to some driver.  They are typically the
  platform side of a change in the drivers directory, such as adding a
  new driver or extending the interface to the platform.  In cases where
  there is no maintainer for the driver, or the maintainer prefers to
  have the platform changes in the same branch as the driver changes,
  the patches to the drivers are included as well.

  A much smaller set of driver updates that depend on other branches
  getting merged first will be sent later.

  The new export of tegra_chip_uid conflicts with other changes in
  fuse.c.  In rtc-sa1100.c, the global removal of IRQF_DISABLED
  conflicts with the cleanup of the interrupt handling of that driver.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up aforementioned trivial conflicts.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
  ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
  mmc: sdhci-s3c: add platform data for the second capability
  ARM: SAMSUNG: support the second capability for samsung-soc
  ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
  ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
  ARM: EXYNOS: Enable MDMA driver
  regulator: Remove bq24022 regulator driver
  rtc: sa1100: add OF support
  pxa: magician/hx4700: Convert to gpio-regulator from bq24022
  ARM: OMAP3+: SmartReflex: fix error handling
  ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
  ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
  ARM: OMAP3+: SmartReflex: misc cleanups
  ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
  ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
  ARM: OMAP3+: hwmod: add SmartReflex IRQs
  ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
  ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
  ARM: OMAP3+: SmartReflex: Add a shutdown hook
  ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
  ...

Conflicts:
	arch/arm/mach-tegra/Makefile
	arch/arm/mach-tegra/fuse.c
	drivers/rtc/rtc-sa1100.c