- 03 Mar, 2015 5 commits
-
-
Jurgen Kramer authored
commit 551c33e7 upstream. Increase si2168 cmd execute timeout to prevent firmware load failures. Tests shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware. Increase timeout to a safe value of 70ms. Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Reviewed-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Roi Dayan authored
commit c6c95ef4 upstream. We always unmap SGs with the same direction instead of unmapping with the direction the mapping was done, fix that. Fixes: 9a8b08fa ("IB/iser: Generalize iser_unmap_task_data and [...]") Signed-off-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Or Gerlitz authored
commit e9a7faf1 upstream. The MLX4_PROT_IB_IPV4 protocol should only be used with RoCEv2 and such. Removing this wrong usage allows to run multicast applications over RoCE. Fixes: d487ee77 ("IB/mlx4: Use IBoE (RoCE) IP based GIDs in the port GID table") Reported-by:
Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by:
-
Moshe Lazer authored
commit 0fb8bcf0 upstream. The deadlock occurs in __uverbs_modify_qp: we take a lock (idr_read_qp) and in case of failure in ib_resolve_eth_l2_attrs we don't release it (put_qp_read). Fix that. Fixes: ed4c54e5 ("IB/core: Resolve Ethernet L2 addresses when modifying QP") Signed-off-by:
Moshe Lazer <moshel@mellanox.com> Signed-off-by:
-
Ilya Nelkenbaum authored
commit c2be9dc0 upstream. When marshaling a user path to the kernel struct ib_sa_path, we need to zero smac and dmac and set the vlan id to the "no vlan" value. This is to ensure that Ethernet attributes are not used with InfiniBand QPs. Fixes: dd5f03be ("IB/core: Ethernet L2 attributes in verbs/cm structures") Signed-off-by:
Ilya Nelkenbaum <ilyan@mellanox.com> Signed-off-by:
-
- 02 Mar, 2015 35 commits
-
-
Hans de Goede authored
commit ce363c2b upstream. It seems that the same problems which lead to adding an rfkill blacklist and putting the Lenovo Yoga 2 11 on it are also present on the Lenovo Yoga 2 13 and Lenovo Yoga 2 Pro too: https://bugzilla.redhat.com/show_bug.cgi?id=1021036 https://forums.lenovo.com/t5/Linux-Discussion/Yoga-2-13-not-Pro-Linux-Warning/m-p/1517612 Testing has shown that the firmware rfkill settings are persistent over reboots. So blacklisting the driver is not good enough, if the wifi is blocked at the firmware level the wifi needs to be explictly unblocked through the ideapad-laptop interface. And at least on the Lenovo Yoga 2 13 the VPCCMD_RF register which on devices with hardware kill switch reports the hardware switch state, needs to be explictly set to 1 (radio enabled / not blocked). So this patch does 3 things to get proper rfkill handling on these models: 1) Instead of blacklisting the rfkill functionality, which means that people with a firmware blocked wifi get stuck in that situation, ignore the value reported by the not present hardware rfkill switch, as this is what is causing ideapad-laptop to wrongly report all radios as hardware blocks. But do register the rfkill interfaces so that the user can soft [un]block them. 2) On models without a hardware rfkill switch, explictly set VPCCMD_RF to 1 3) Drop the " 11" postfix from the dmi match string, as the entire Yoga 2 series is affected. Yoga 2 11: Reported-and-tested-by:
Vincent Gerris <vgerris@gmail.com> Yoga 2 13: Tested-by: madls05 <http://ubuntuforums.org/showthread.php?t=2215044> Yoga 2 Pro: Reported-and-tested-by:
Peter F. Patel-Schneider <pfpschneider@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Matthew Garrett <matthew.garrett@nebula.com> Cc: Gaudenz Steinlin <gaudenz@debian.org> Signed-off-by:
-
Daniel Borkmann authored
commit 4c672e4b upstream. It has been reported that generating an MLD listener report on devices with large MTUs (e.g. 9000) and a high number of IPv6 addresses can trigger a skb_over_panic(): skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20 head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0 dev:port1 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:100! invalid opcode: 0000 [#1] SMP Modules linked in: ixgbe(O) CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4 [...] Call Trace: <IRQ> [<ffffffff80578226>] ? skb_put+0x3a/0x3b [<ffffffff80612a5d>] ? add_grhead+0x45/0x8e [<ffffffff80612e3a>] ? add_grec+0x394/0x3d4 [<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d [<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45 [<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68 [<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182 [<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d [<ffffffff8025112b>] ? irq_exit+0x4e/0xd3 [<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46 [<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70 mld_newpack() skb allocations are usually requested with dev->mtu in size, since commit 72e09ad1 ("ipv6: avoid high order allocations") we have changed the limit in order to be less likely to fail. However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb) macros, which determine if we may end up doing an skb_put() for adding another record. To avoid possible fragmentation, we check the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong assumption as the actual max allocation size can be much smaller. The IGMP case doesn't have this issue as commit 57e1ab6e ("igmp: refine skb allocations") stores the allocation size in the cb[]. Set a reserved_tailroom to make it fit into the MTU and use skb_availroom() helper instead. This also allows to get rid of igmp_skb_size(). Reported-by:
Wei Liu <lw1a2.jing@gmail.com> Fixes: 72e09ad1 ("ipv6: avoid high order allocations") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: David L Stevens <david.stevens@oracle.com> Acked-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Johan Hovold authored
commit ebbeba12 upstream. Fix attribute-creation race with userspace by using the default group to create also the contingent gpio device attributes. Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - all changes in drivers/gpio/gpiolib.c - adjusted context ] Signed-off-by:
-
Daniel Borkmann authored
commit 2061dcd6 upstream. I.e. one-to-many sockets in SCTP are not required to explicitly call into connect(2) or sctp_connectx(2) prior to data exchange. Instead, they can directly invoke sendmsg(2) and the SCTP stack will automatically trigger connection establishment through 4WHS via sctp_primitive_ASSOCIATE(). However, this in its current implementation is racy: INIT is being sent out immediately (as it cannot be bundled anyway) and the rest of the DATA chunks are queued up for later xmit when connection is established, meaning sendmsg(2) will return successfully. This behaviour can result in an undesired side-effect that the kernel made the application think the data has already been transmitted, although none of it has actually left the machine, worst case even after close(2)'ing the socket. Instead, when the association from client side has been shut down e.g. first gracefully through SCTP_EOF and then close(2), the client could afterwards still receive the server's INIT_ACK due to a connection with higher latency. This INIT_ACK is then considered out of the blue and hence responded with ABORT as there was no alive assoc found anymore. This can be easily reproduced f.e. with sctp_test application from lksctp. One way to fix this race is to wait for the handshake to actually complete. The fix defers waiting after sctp_primitive_ASSOCIATE() and sctp_primitive_SEND() succeeded, so that DATA chunks cooked up from sctp_sendmsg() have already been placed into the output queue through the side-effect interpreter, and therefore can then be bundeled together with COOKIE_ECHO control chunks. strace from example application (shortened): socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...}, msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF close(3) = 0 tcpdump before patch (fooling the application): 22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684] 22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591] 22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT] tcpdump after patch: 14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729] 14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492] 14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...] 14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0] 14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...] 14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0] 14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...] 14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0] 14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN] 14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK] 14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE] Looks like this bug is from the pre-git history museum. ;) Fixes: 08707d54 ("lksctp-2_5_31-0_5_1.patch") Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Alexander Duyck authored
commit a5a519b2 upstream. In recent testing I had disabled CONFIG_IP_MULTIPLE_TABLES and as a result when I ran "cat /proc/net/fib_trie" the main trie was displayed multiple times. I found that the problem line of code was in the function fib_trie_seq_next. Specifically the line below caused the indexes to go in the opposite direction of our traversal: h = tb->tb_id & (FIB_TABLE_HASHSZ - 1); This issue was that the RT tables are defined such that RT_TABLE_LOCAL is ID 255, while it is located at TABLE_LOCAL_INDEX of 0, and RT_TABLE_MAIN is 254 with a TABLE_MAIN_INDEX of 1. This means that the above line will return 1 for the local table and 0 for main. The result is that fib_trie_seq_next will return NULL at the end of the local table, fib_trie_seq_start will return the start of the main table, and then fib_trie_seq_next will loop on main forever as h will always return 0. The fix for this is to reverse the ordering of the two tables. It has the advantage of making it so that the tables now print in the same order regardless of if multiple tables are enabled or not. In order to make the definition consistent with the multiple tables case I simply masked the to RT_TABLE_XXX values by (FIB_TABLE_HASHSZ - 1). This way the two table layouts should always stay consistent. Fixes: 93456b6d ("[IPV4]: Unify access to the routing tables") Signed-off-by:
Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by:
-
Seth Forshee authored
commit 6d00f37e upstream. d1c7e29e (HID: i2c-hid: prevent buffer overflow in early IRQ) changed hid_get_input() to read ihid->bufsize bytes, which can be more than wMaxInputLength. This is the case with the Dell XPS 13 9343, and it is causing events to be missed. In some cases the missed events are releases, which can cause the cursor to jump or freeze, among other problems. Limit the number of bytes read to min(wMaxInputLength, ihid->bufsize) to prevent such problems. Fixes: d1c7e29e "HID: i2c-hid: prevent buffer overflow in early IRQ" Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Sasha Levin authored
commit db27ebb1 upstream. Max unacked packets/bytes is an int while sizeof(long) was used in the sysctl table. This means that when they were getting read we'd also leak kernel memory to userspace along with the timeout values. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Sasha Levin authored
commit 6b8d9117 upstream. The timeout entries are sizeof(int) rather than sizeof(long), which means that when they were getting read we'd also leak kernel memory to userspace along with the timeout values. Signed-off-by:
-
Andrew Elble authored
commit 27870207 upstream. Fixes: e01580bf ("gfs2: use generic posix ACL infrastructure") Reported-by:
Eric Meddaugh <etmsys@rit.edu> Tested-by:
Andrew Elble <aweits@rit.edu> Signed-off-by:
Steven Whitehouse <swhiteho@redhat.com> Signed-off-by:
-
Dan Carpenter authored
commit e4940626 upstream. The problem here is that we check: if (dev >= SNDRV_CARDS) Then we increment "dev". if (!joystick_port[dev++]) Then we use it as an offset into a array with SNDRV_CARDS elements. if (!request_region(joystick_port[dev], 8, "Riptide gameport")) { This has 3 effects: 1) If you use the module option to specify the joystick port then it has to be shifted one space over. 2) The wrong error message will be printed on failure if you have over 32 cards. 3) Static checkers will correctly complain that are off by one. Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Uwe Kleine-König authored
commit 4ff0f034 upstream. The right check for conf_reg to be invalid it testing against -1 not 0 as is done in the rest of the driver. This fixes an oops that can be triggered by: cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/* Fixes: ae75ff81 ("pinctrl: pinctrl-imx: add imx pinctrl core driver") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Gavin Shan authored
commit 6f20e7f2 upstream. When calling to early_setup(), we pick "boot_paca" up for the master CPU and initialize that with initialise_paca(). At that point, the SLB shadow buffer isn't populated yet. Updating the SLB shadow buffer should corrupt what we had in physical address 0 where the trap instruction is usually stored. This hasn't been observed to cause any trouble in practice, but is obviously fishy. Fixes: 6f4441ef ("powerpc: Dynamically allocate slb_shadow from memblock") Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Sergei Shtylyov authored
commit 2e9dcdae upstream. In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit # should be no higher than 15, however the corresponding check is obviously off- by-one. Fixes: 04577994 ("clk: gate: add CLK_GATE_HIWORD_MASK") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit 86d68a58 upstream. The "> 0" here should ">= 0" so we free map_entries[0]. Fixes: 926172d4 ('efi: Export EFI runtime memory mapping to sysfs') Signed-off-by:
Dave Young <dyoung@redhat.com> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit 7d82bf34 upstream. If the call to devm_kzalloc() fails, nothing must be cleant up. This was missed before because gpio_rcar_probe() had a "return" statement after the first "goto err0". Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Fixes: df0c6c80 ("gpio: rcar: Add minimal runtime PM support") Signed-off-by:
-
Lars-Peter Clausen authored
commit 7331ea47 upstream. Commit f6b2a045 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM setup") converted the driver to register the board level DAPM elements with the card's DAPM context rather than the CODEC's DAPM context. The change overlooked that the speaker widget event callback accesses the widget's codec field which is only valid if the widget has been registered in a CODEC DAPM context. This patch modifies the callback to take an alternative route to get the CODEC. Fixes: f6b2a045 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM setup") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Al Viro authored
commit 0a280962 upstream. X-Coverup: just ask spender Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 7e0e953b upstream. use_pde()/unuse_pde() in ->follow_link()/->put_link() resp. Signed-off-by:
-
Al Viro authored
commit 0db59e59 upstream. As it is, we have debugfs_remove() racing with symlink traversals. Supply ->evict_inode() and do freeing there - inode will remain pinned until we are done with the symlink body. And rip the idiocy with checking if dentry is positive right after we'd verified debugfs_positive(), which is a stronger check... Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
commit 045c47ca upstream. When reading blkio.throttle.io_serviced in a recently created blkio cgroup, it's possible to race against the creation of a throttle policy, which delays the allocation of stats_cpu. Like other functions in the throttle code, just checking for a NULL stats_cpu prevents the following oops caused by that race. [ 1117.285199] Unable to handle kernel paging request for data at address 0x7fb4d0020 [ 1117.285252] Faulting instruction address: 0xc0000000003efa2c [ 1137.733921] Oops: Kernel access of bad area, sig: 11 [#1] [ 1137.733945] SMP NR_CPUS=2048 NUMA PowerNV [ 1137.734025] Modules linked in: bridge stp llc kvm_hv kvm binfmt_misc autofs4 [ 1137.734102] CPU: 3 PID: 5302 Comm: blkcgroup Not tainted 3.19.0 #5 [ 1137.734132] task: c000000f1d188b00 ti: c000000f1d210000 task.ti: c000000f1d210000 [ 1137.734167] NIP: c0000000003efa2c LR: c0000000003ef9f0 CTR: c0000000003ef980 [ 1137.734202] REGS: c000000f1d213500 TRAP: 0300 Not tainted (3.19.0) [ 1137.734230] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 42008884 XER: 20000000 [ 1137.734325] CFAR: 0000000000008458 DAR: 00000007fb4d0020 DSISR: 40000000 SOFTE: 0 GPR00: c0000000003ed3a0 c000000f1d213780 c000000000c59538 0000000000000000 GPR04: 0000000000000800 0000000000000000 0000000000000000 0000000000000000 GPR08: ffffffffffffffff 00000007fb4d0020 00000007fb4d0000 c000000000780808 GPR12: 0000000022000888 c00000000fdc0d80 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 000001003e120200 c000000f1d5b0cc0 0000000000000200 0000000000000000 GPR24: 0000000000000001 c000000000c269e0 0000000000000020 c000000f1d5b0c80 GPR28: c000000000ca3a08 c000000000ca3dec c000000f1c667e00 c000000f1d213850 [ 1137.734886] NIP [c0000000003efa2c] .tg_prfill_cpu_rwstat+0xac/0x180 [ 1137.734915] LR [c0000000003ef9f0] .tg_prfill_cpu_rwstat+0x70/0x180 [ 1137.734943] Call Trace: [ 1137.734952] [c000000f1d213780] [d000000005560520] 0xd000000005560520 (unreliable) [ 1137.734996] [c000000f1d2138a0] [c0000000003ed3a0] .blkcg_print_blkgs+0xe0/0x1a0 [ 1137.735039] [c000000f1d213960] [c0000000003efb50] .tg_print_cpu_rwstat+0x50/0x70 [ 1137.735082] [c000000f1d2139e0] [c000000000104b48] .cgroup_seqfile_show+0x58/0x150 [ 1137.735125] [c000000f1d213a70] [c0000000002749dc] .kernfs_seq_show+0x3c/0x50 [ 1137.735161] [c000000f1d213ae0] [c000000000218630] .seq_read+0xe0/0x510 [ 1137.735197] [c000000f1d213bd0] [c000000000275b04] .kernfs_fop_read+0x164/0x200 [ 1137.735240] [c000000f1d213c80] [c0000000001eb8e0] .__vfs_read+0x30/0x80 [ 1137.735276] [c000000f1d213cf0] [c0000000001eb9c4] .vfs_read+0x94/0x1b0 [ 1137.735312] [c000000f1d213d90] [c0000000001ebb38] .SyS_read+0x58/0x100 [ 1137.735349] [c000000f1d213e30] [c000000000009218] syscall_exit+0x0/0x98 [ 1137.735383] Instruction dump: [ 1137.735405] 7c6307b4 7f891800 409d00b8 60000000 60420000 3d420004 392a63b0 786a1f24 [ 1137.735471] 7d49502a e93e01c8 7d495214 7d2ad214 <7cead02a> e9090008 e9490010 e9290018 And here is one code that allows to easily reproduce this, although this has first been found by running docker. void run(pid_t pid) { int n; int status; int fd; char *buffer; buffer = memalign(BUFFER_ALIGN, BUFFER_SIZE); n = snprintf(buffer, BUFFER_SIZE, "%d\n", pid); fd = open(CGPATH "/test/tasks", O_WRONLY); write(fd, buffer, n); close(fd); if (fork() > 0) { fd = open("/dev/sda", O_RDONLY | O_DIRECT); read(fd, buffer, 512); close(fd); wait(&status); } else { fd = open(CGPATH "/test/blkio.throttle.io_serviced", O_RDONLY); n = read(fd, buffer, BUFFER_SIZE); close(fd); } free(buffer); exit(0); } void test(void) { int status; mkdir(CGPATH "/test", 0666); if (fork() > 0) wait(&status); else run(getpid()); rmdir(CGPATH "/test"); } int main(int argc, char **argv) { int i; for (i = 0; i < NR_TESTS; i++) test(); return 0; } Reported-by:
Ricardo Marin Matinata <rmm@br.ibm.com> Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Jay Lan authored
commit 14675592 upstream. The output of KDB 'summary' command should report MemTotal, MemFree and Buffers output in kB. Current codes report in unit of pages. A define of K(x) as is defined in the code, but not used. This patch would apply the define to convert the values to kB. Please include me on Cc on replies. I do not subscribe to linux-kernel. Signed-off-by:
Jay Lan <jlan@sgi.com> Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
James Hogan authored
commit ca5d2564 upstream. Export the _save_msa asm function used by the lose_fpu(1) macro to GPL modules so that KVM can make use of it when it is built as a module. This fixes the following build error when CONFIG_KVM=m and CONFIG_CPU_HAS_MSA=y due to commit f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"): ERROR: "_save_msa" [arch/mips/kvm/kvm.ko] undefined! Fixes: f798217d (KVM: MIPS: Don't leak FPU/DSP to guest) Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9261/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
James Hogan authored
commit 3ce465e0 upstream. Export the _save_fp asm function used by the lose_fpu(1) macro to GPL modules so that KVM can make use of it when it is built as a module. This fixes the following build error when CONFIG_KVM=m due to commit f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"): ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined! Signed-off-by:
-
Ilya Dryomov authored
commit 7eb71e03 upstream. It turns out it's possible to get __remove_osd() called twice on the same OSD. That doesn't sit well with rb_erase() - depending on the shape of the tree we can get a NULL dereference, a soft lockup or a random crash at some point in the future as we end up touching freed memory. One scenario that I was able to reproduce is as follows: <osd3 is idle, on the osd lru list> <con reset - osd3> con_fault_finish() osd_reset() <osdmap - osd3 down> ceph_osdc_handle_map() <takes map_sem> kick_requests() <takes request_mutex> reset_changed_osds() __reset_osd() __remove_osd() <releases request_mutex> <releases map_sem> <takes map_sem> <takes request_mutex> __kick_osd_requests() __reset_osd() __remove_osd() <-- !!! A case can be made that osd refcounting is imperfect and reworking it would be a proper resolution, but for now Sage and I decided to fix this by adding a safe guard around __remove_osd(). Fixes: http://tracker.ceph.com/issues/8087 Cc: Sage Weil <sage@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Reviewed-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Ilya Dryomov authored
commit cc9f1f51 upstream. No reason to use BUG_ON for osd request list assertions. Signed-off-by:
Ilya Dryomov <idryomov@redhat.com> Reviewed-by:
-
Ilya Dryomov authored
commit 7c6e6fc5 upstream. It is important that both regular and lingering requests lists are empty when the OSD is removed. Signed-off-by:
Ilya Dryomov <ilya.dryomov@inktank.com> Reviewed-by:
-
Hector Marco-Gisbert authored
commit 4e7c22d4 upstream. The issue is that the stack for processes is not properly randomized on 64 bit architectures due to an integer overflow. The affected function is randomize_stack_top() in file "fs/binfmt_elf.c": static unsigned long randomize_stack_top(unsigned long stack_top) { unsigned int random_variable = 0; if ((current->flags & PF_RANDOMIZE) && !(current->personality & ADDR_NO_RANDOMIZE)) { random_variable = get_random_int() & STACK_RND_MASK; random_variable <<= PAGE_SHIFT; } return PAGE_ALIGN(stack_top) + random_variable; return PAGE_ALIGN(stack_top) - random_variable; } Note that, it declares the "random_variable" variable as "unsigned int". Since the result of the shifting operation between STACK_RND_MASK (which is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64): random_variable <<= PAGE_SHIFT; then the two leftmost bits are dropped when storing the result in the "random_variable". This variable shall be at least 34 bits long to hold the (22+12) result. These two dropped bits have an impact on the entropy of process stack. Concretely, the total stack entropy is reduced by four: from 2^28 to 2^30 (One fourth of expected entropy). This patch restores back the entropy by correcting the types involved in the operations in the functions randomize_stack_top() and stack_maxrandom_size(). The successful fix can be tested with: $ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done 7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0 [stack] 7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0 [stack] 7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0 [stack] 7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0 [stack] ... Once corrected, the leading bytes should be between 7ffc and 7fff, rather than always being 7fff. Signed-off-by:
Hector Marco-Gisbert <hecmargi@upv.es> Signed-off-by:
Ismael Ripoll <iripoll@upv.es> [ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ] Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Fixes: CVE-2015-1593 Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.netSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Arnd Bergmann authored
commit 61882b63 upstream. The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register are marked init but are called from a context that might be run after the __init sections are discarded, as the compiler points out: WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init() WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register() This removes the __init markings. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Mikulas Patocka authored
commit 22aa66a3 upstream. When the snapshot target is unloaded, snapshot_dtr() waits until pending_exceptions_count drops to zero. Then, it destroys the snapshot. Therefore, the function that decrements pending_exceptions_count should not touch the snapshot structure after the decrement. pending_complete() calls free_pending_exception(), which decrements pending_exceptions_count, and then it performs up_write(&s->lock) and it calls retry_origin_bios() which dereferences s->origin. These two memory accesses to the fields of the snapshot may touch the dm_snapshot struture after it is freed. This patch moves the call to free_pending_exception() to the end of pending_complete(), so that the snapshot will not be destroyed while pending_complete() is in progress. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit 2bec1f4a upstream. The function dm_get_md finds a device mapper device with a given dev_t, increases the reference count and returns the pointer. dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the device, tests that the device doesn't have DMF_DELETING or DMF_FREEING flag, drops _minor_lock and returns pointer to the device. dm_get_md then calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag, otherwise it increments the reference count. There is a possible race condition - after dm_find_md exits and before dm_get is called, there are no locks held, so the device may disappear or DMF_FREEING flag may be set, which results in BUG. To fix this bug, we need to call dm_get while we hold _minor_lock. This patch renames dm_find_md to dm_get_md and changes it so that it calls dm_get while holding the lock. Signed-off-by:
-
John Stultz authored
commit 29183a70 upstream. Additional validation of adjtimex freq values to avoid potential multiplication overflows were added in commit 5e5aeb43 (time: adjtimex: Validate the ADJ_FREQUENCY values) Unfortunately the patch used LONG_MAX/MIN instead of LLONG_MAX/MIN, which was fine on 64-bit systems, but being much smaller on 32-bit systems caused false positives resulting in most direct frequency adjustments to fail w/ EINVAL. ntpd only does direct frequency adjustments at startup, so the issue was not as easily observed there, but other time sync applications like ptpd and chrony were more effected by the bug. See bugs: https://bugzilla.kernel.org/show_bug.cgi?id=92481 https://bugzilla.redhat.com/show_bug.cgi?id=1188074 This patch changes the checks to use LLONG_MAX for clarity, and additionally the checks are disabled on 32-bit systems since LLONG_MAX/PPM_SCALE is always larger then the 32-bit long freq value, so multiplication overflows aren't possible there. Reported-by:
Josh Boyer <jwboyer@fedoraproject.org> Reported-by:
George Joseph <george.joseph@fairview5.com> Tested-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Sasha Levin <sasha.levin@oracle.com> Link: http://lkml.kernel.org/r/1423553436-29747-1-git-send-email-john.stultz@linaro.org [ Prettified the changelog and the comments a bit. ] Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sasha Levin authored
commit 5e5aeb43 upstream. Verify that the frequency value from userspace is valid and makes sense. Unverified values can cause overflows later on. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 8d1e5a1a upstream. With task_blocks_on_rt_mutex() returning early -EDEADLK we never add the waiter to the waitqueue. Later, we try to remove it via remove_waiter() and go boom in rt_mutex_top_waiter() because rb_entry() gives a NULL pointer. ( Tested on v3.18-RT where rtmutex is used for regular mutex and I tried to get one twice in a row. ) Not sure when this started but I guess 397335f0 ("rtmutex: Fix deadlock detector for real") or commit 3d5c9340 ("rtmutex: Handle deadlock detection smarter"). Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
-
NeilBrown authored
commit 26ac1073 upstream. Commit a7854487: md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write. Causes an RCW cycle to be forced even when the array is degraded. A degraded array cannot support RCW as that requires reading all data blocks, and one may be missing. Forcing an RCW when it is not possible causes a live-lock and the code spins, repeatedly deciding to do something that cannot succeed. So change the condition to only force RCW on non-degraded arrays. Reported-by:
Manibalan P <pmanibalan@amiindia.co.in> Bisected-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Tested-by:
NeilBrown <neilb@suse.de> Fixes: a7854487Signed-off-by:
-
Markos Chandras authored
commit acac4108 upstream. The "addi" instruction will trap on overflows which is not something we need in this code, so we replace that with "addiu". Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00430.html Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Signed-off-by:
Markos Chandras <markos.chandras@imgtec.com> Signed-off-by:
-
