- 26 Sep, 2016 40 commits
-
-
Baolin Wang authored
In most cases the 'card->erase_size' is power of 2, then the round_up/down() function is more efficient than '%' operation when the 'card->erase_size' is power of 2. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Tested-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Baolin Wang authored
In order to clean up the mmc_erase() function and do some optimization for erase size alignment, factor out the guts of erase size alignment into mmc_align_erase_size() function. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Tested-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Arnd Bergmann authored
platform_get_irq() returns an error value on failure, not NO_IRQ, so the error handling here could never work. This changes the code to propagate the error value instead. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Ai Kyuse authored
Add support for r8a7796 SoC. Signed-off-by:
Ai Kyuse <ai.kyuse.uw@renesas.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Ulf Hansson authored
In cases when the host->max_busy_timeout isn't specified, the calculated number of maximum discard sectors defaults to UINT_MAX. This may cause a too long timeout for a discard request. Avoid this by using a default maximum erase timeout of 60s, used when we calculate the maximum number of sectors that are allowed to be discarded per request. Do note that the minimum number of sectors to be discarded is still at least one "preferred erase size". Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com>
-
Thierry Reding authored
According to the TRM, the SD/MMC controller on Tegra124 supports 34-bit addressing, but testing shows that this doesn't work. On a device which has more than 2 GiB of RAM and LPAE enabled, buffer allocations can use addresses above the 32-bit boundary. One way to work around this would be to enable IOMMU physical to virtual address translations for the SD/MMC controllers, but that's not easy to implement without breaking existing use-cases. It's also not obvious why 34-bit addressing doesn't work as advertised. In order to fix this for existing users, add the SDHCI_QUIRK2_BROKEN_64_BIT_DMA quirk for now. Reported-by:
Paul Kocialkowski <contact@paulk.fr> Acked-by:
Stephen Warren <swarren@nvidia.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Shawn Lin authored
corecfg_clockmultiplier indicates clock multiplier value of programmable clock generator which should be the same value of SDHCI_CAPABILITIES_1. The default value of the register, corecfg_clockmultiplier, is 0x10. But actually it is a mistake by designer as our intention was to set it to be zero which means we don't support programmable clock generator. So we have to make it to be zero on bootloader which seems work fine until now. But now we find an issue that when deploying genpd support for it, the remove callback will trigger the genpd to poweroff the power domain for sdhci-of-arasan which manage the controller, phy and corecfg_* stuff. So when we do bind/unbind the driver, we have already reinit the controller and phy, but without doing that for corecfg_*. Regarding to only the corecfg_clockmultipler is wrong, let's fix it by explicitly marking it to be zero when probing. With this change, we could do bind/unbind successfully. Reported-by:
Ziyuan Xu <xzy.xu@rock-chips.com> Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by:
Ziyuan Xu <xzy.xu@rock-chips.com> Tested-by:
Ziyuan Xu <xzy.xu@rock-chips.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Andy Shevchenko authored
Intel Merrifield provides an interface to an external SD card. Enable it here. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Andy Shevchenko authored
Intel Merrifield is known to have an SDIO interface and on Intel Edison board a WiFi card is wired to it. Enable the interface here to allow WiFi card enumeration. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Andy Shevchenko authored
Refactor intel_mrfld_mmc_probe_slot() to use switch case. The change allows to add a support for SD and SDIO interfaces without any pain. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Jin Guojun authored
Hisilicon Hikey have no tuning function in dw_mmc-k3.c, so we must do the tuning function stub when we init UHS card. Signed-off-by:
Jin Guojun <kid.jin@hisilicon.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Shawn Lin authored
The following log we found indicate the fact that dw_mmc didn't treat EBE or SBE as a similar problem as CRC error. -EIO is quite not informative as it may indicate that the device is broken rather than that of tuning stuff. ... [ 89.057226] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5 [ 89.058811] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5 [ 89.059415] bcmsdh_sdmmc: Failed to Read byte F1:@0x1000e=ff, Err: -84 [ 89.254248] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 199 [ 89.273912] dhd_set_suspend: Remove extra suspend setting [ 89.274478] dhd_enable_packet_filter: enter, value = 0 64 bytes from 112.90.83.112: icmp_seq=24 ttl=53 time=1321 ms 64 bytes from 112.90.83.112: icmp_seq=25 ttl=53 time=319 ms 64 bytes from 112.90.83.112: icmp_seq=26 ttl=53 time=69.8 ms 64 bytes from 112.90.83.112: icmp_seq=27 ttl=53 time=37.5 ms ... For the host, when failing to sample cmd's response due to tuning stuff, we still return -EIO as it's quite vague to figure out whether it related to signal or just the broken devices, especially for the card type detection when booting kernel as all things go well but the cmd set used. But for the data phase, if receiving the cmd's response which carriess data transfer, we should have more confidence that it is very probably related to the tuning stuff. Just as the log shown above, we sometimes suffer too much this kind of pain as the dw_mmc return -EIO for the case, so mmc-core will not do retune and caller drivers like bcm's wifi driver, still retry the failure more and more until dw_mmc finally generate CRC. Adrian suggested that drivers who care the specific cases should call mmc_retune_needed rather than doing it in mmc core. It makes sense but I'm considering that -EILSEQ actually means illegal sequence , so we use it for CRC cases. Meanwhile, SBE/EBE indicate the illegal sequence of start bit or end bit for data0~7. So I realize that we should use -EILSEQ for them both as well CRC cases. Suggested-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Guodong Xu authored
Dwmmc host controller may in unknown state when entering kernel boot. One example is when booting from eMMC, bootloader need initialize MMC host controller into some state so it can read. In order to make sure MMC host controller in a clean initial state, this reset support is added. With this patch, a 'resets' property can be added into dw_mmc device tree node. The hardware logic is: dwmmc host controller IP receives a reset signal from a 'reset provider' (eg. power management unit). The 'resets' property points to this reset signal. So, during dwmmc driver probe, it can use this signal to reset itself. Refer to [1] for more information. [1] Documentation/devicetree/bindings/reset/reset.txt Signed-off-by:
Guodong Xu <guodong.xu@linaro.org> Signed-off-by:
Xinwei Kong <kong.kongxinwei@hisilicon.com> Signed-off-by:
Zhangfei Gao <zhangfei.gao@linaro.org> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Guodong Xu authored
Add resets property to synopsys-dw-mshc bindings. It is intended to represent the hardware reset signal present internally in some host controller IC designs. See Documentation/devicetree/bindings/reset/reset.txt for details. Signed-off-by:
Guodong Xu <guodong.xu@linaro.org> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Jaehoon Chung authored
If ciu/biu clock are NULL, clk_disable_unprepare should be just returned. In clk_disable_unprepare(), already checked whether clk is error or NULL. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Shawn Lin authored
The intention to remove it comes from the conflict of what the mmc-core does with the way dw_mmc treats disable-wp. We could see that 'disable-wp' is supported by core but it's deprecated by dw_mmc as we don't expect it to be existed for each slot subnode but should be in the parent node. Based on searching for all the upstream dts using dw_mmc, we're confident that none of them use the deprecated way. Maybe we should take old dtb in consideration but it was a flag day since the time we was considering to take it away. The fact is that there are none of dts using the deprecated way since v3.18 or even earlier. So personally I don't believe the old dtb would/could bootup current kernel(may not?). Let's remove it now. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Krzysztof Kozlowski authored
Chipsets before Exynos5420 did not support HS400 so if MMC core tries to configure HS400 timing, this might or might not work. Warn in such cases because this is DTB misconfiguration. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Daniel Glöckner authored
CMD23 aka SET_BLOCK_COUNT was introduced with MMC v3.1. Older versions of the specification allowed to terminate multi-block transfers only with CMD12. The patch fixes the following problem: mmc0: new MMC card at address 0001 mmcblk0: mmc0:0001 SDMB-16 15.3 MiB mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 ... blk_update_request: I/O error, dev mmcblk0, sector 0 Buffer I/O error on dev mmcblk0, logical block 0, async page read mmcblk0: unable to read partition table Signed-off-by:
Daniel Glöckner <dg@emlix.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Ulf Hansson authored
The commit 1ef5e49e ("mmc: sdhci-of-esdhc: add/remove some quirks according to vendor version") moved sdhci-of-esdhc away from using the ->platform_init() callback. As it was the only user of it and that it seems reasonable to believe that it won't be needed again, let's just remove it. Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com>
-
Andy Shevchenko authored
The commit 52ac7acf ("mmc: sdhci-pci: Convert to use managed functions pcim_* and devm_*") converted ->probe() / ->remove() functions to use device managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and sdhci_pci_remove_slot(). Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Shawn Lin authored
When using mmc_io_rw_extended, it's intent to avoid null pointer of card and invalid func number. But actually it didn't prevent that as the seg_size already use the card. Currently the wrapper function sdio_io_rw_ext_helper already use card before calling mmc_io_rw_extended, so we should move this check to there. As to the func number, it was token from '(ocr & 0x70000000) >> 28' which should be enough to guarantee that it won't be larger than 7. But we should prevent the caller like wifi drivers modify this value. So let's move this check into sdio_io_rw_ext_helper either. Also we remove the BUG_ON for mmc_send_io_op_cond since all possible paths calling this function are protected by checking the arguments in advance. After deploying these changes, we could not see any panic within SDIO API even if func drivers abuse the SDIO func APIs. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Shawn Lin authored
packed should always exist without calling its cleanup function explicitly. Moreover, we have use it when preparing packed list. So I don't believe we should ever fall into this check again when doing mmc_blk_packed_hdr_wrq_prep or mmc_blk_end_packed_req,etc. And the code of mmc_blk_end_packed_req is trying to use packed before checking it which makes it quite weird. This patch is trying to remove these two checks and move it to the mmc_blk_prep_packed_list. If we find packed is null, then we should never use MMC_BLK_PACKED_CMD. By doing this, we could fall back to non-packed request if finding null packed, though it's impossible theoretically. After removing these two BUG_ONs, we also remove all other similar checks within the routine of mmc_blk_issue_rw_rq which checks the error handling of packed request. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Jungseung Lee authored
The switch failure message in mmc_select_timing() had been removed since that is invalid: commit 0400ed0a ("mmc: core: remove the invalid message in mmc_select_timing") Now, in the case when mmc_select_hs() return error in mmc_select_timing(), there is nothing to print failure message. Let's make for mmc_select_hs() print message itself in the failure case. Signed-off-by:
Jungseung Lee <js07.lee@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
Populating card_busy caused a side-effect on a chip variant we don't have documentation for (r8a73a4). So, enable it and voltage switching only on devices known to support those features. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Fixes: 452e5eef ("mmc: tmio: Add UHS-I mode support")
-
Wolfram Sang authored
card_busy is only used/tested on SDHI for R-Car Gen2 and later. Move it to the SDHI driver, so we can then activate it conditionally depending on the SDHI type. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Michael Weiser authored
The sunxi-mmc driver does not take into account the processor may be big endian when writing the DMA descriptors. This causes cards not to be detected when running a big-endian kernel. Change the descriptors for IDMA to use __le32 and ensure they are suitably swapped before writing. Tested successfully on the Cubieboard2. Signed-off-by:
Michael Weiser <michael.weiser@gmx.de> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-mmc@vger.kernel.org Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Jean-Francois Moine authored
clk_round_rate() may return an error. Check it. Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Douglas Anderson authored
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble turning on when the card clock is slow or off. Strangely these problems appear to show up consistently on some boards while other boards work fine, but on the boards where it shows up the problem reproduces 100% of the time and is quite consistent in its behavior. These problems can be fixed by always making sure that we power on the PHY (and turn on its DLL) when the card clock is faster than about 50 MHz. Once on, we need to make sure that we never power down the PHY / turn off its DLL until the clock is faster again. We'll add logic for handling this into the sdhci-of-arasan driver. Note that right now the only user of a PHY in the sdhci-of-arasan driver is arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY implementations need this workaround, so the logic is only contingent on having a PHY to control. If future Arasan controllers don't have this problem we can add code to decide if we want this flow or not. Also note that we check for slow clocks by checking for <= 400 kHz rather than checking for 50 MHz. This keeps things the most consistent and also means we can power the PHY on at max speed (where the DLL will lock fastest). Presumably anyone who intends to run with a card clock of < 50 MHz and > 400 kHz will be running on a device where this problem is fixed anyway. I believe this brings some resolution to the problems reported before. See the commit 6fc09244 ("mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes"). Signed-off-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Christopher Freeman authored
wait_event_interruptible_timeout() will return early if the blocked process receives a signal, causing the driver to abort the tuning procedure and possibly leaving the controller in a bad state. Since the tuning command is expected to complete quickly (<50ms) and we've set a timeout, use wait_event_timeout() instead. Signed-off-by:
Christopher Freeman <cfreeman@nvidia.com> Tested-by:
Robert Foss <robert.foss@collabora.com> Signed-off-by:
Robert Foss <robert.foss@collabora.com> Reviewed-by:
Benson Leung <bleung@chromium.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Haibo Chen authored
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL, the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV is set to 0xF, it means SDCLK << 29, not SDCLK << 28. Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Haibo Chen authored
Now, when call esdhc_set_timeout() to set the data timeout counter value, IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this. Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Markus Elfring authored
The field "owner" is set by core. Thus delete an extra initialisation. Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Uri Yanai authored
The SD Status register contains several important fields related to the SD Card proprietary features. Those fields may be used by user space applications for vendor specific usage. None of those fields are exported today by the driver to user space. In this patch, we are reading the SD Status register and exporting (using MMC_DEV_ATTR) the SD Status register to the user space. Signed-off-by:
Uri Yanai <uri.yanai@sandisk.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
kmalloc will print enough information in case of failure. Signed-off-by:
Wolfram Sang <wsa-dev@sang-engineering.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Julia Lawall authored
Use of_property_read_bool to check for the existence of a property. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e1,e2; statement S2,S1; @@ - if (of_get_property(e1,e2,NULL)) + if (of_property_read_bool(e1,e2)) S1 else S2 // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Ben Dooks authored
The core MMC code adds two (optional) regulator properites that drivers should use to get their supplies. This is not documented anywhere so add information on it. Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Wei Yongjun authored
In clk_set_rate() or clk_prepare_enable() error handling case, the error return code ret is not set, so sdhci_bcm_kona_probe() return 0 in those error cases. Signed-off-by:
Wei Yongjun <weiyj.lk@gmail.com> Acked-by:
Ray Jui <ray.jui@broadcom.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Nicholas Mc Guire authored
wait_for_completion_timeout_interruptible returns long not unsigned long so dma_time, which is used exclusively here, is changed to long. Fixes: 1b66e94e ("mmc: moxart: Add MOXA ART SD/MMC driver") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Hans de Goede authored
Some devices need a while to boot their firmware after providing clks / de-asserting resets before they are ready to receive sdio commands. This commits adds a post-power-on-delay-ms devicetree property to mmc-pwrseq-simple for use with such devices. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Hans de Goede authored
On some boards (android tablets) different batches use different sdio wifi modules. This is not a problem since mmc/sdio is an enumerable bus, so we only need to describe and activate the mmc controller in dt and then the kernel will automatically load the right driver. Sometimes it is useful to specify certain ethernet properties for these "unknown" sdio devices, specifically we want the boot-loader to be able to set "local-mac-address" as some of these sdio wifi modules come without an eeprom / without a factory programmed mac address. Since the exact device is unknown (differs per batch) we cannot use a wifi-chip specific compatible, thus sometimes it is desirable to have a mmc function node, without having to make up an otherwise unused compatible for the node, so make the compatible property optional. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-