For PUNIT device, ISPDRIVER_IPC and GTDDRIVER_IPC resources are not
mandatory. So when PMC IPC driver creates a PUNIT device, if these
resources are not available then it creates dummy resource entries for
these missing resources. But during PUNIT device probe, doing ioremap on
these dummy resources generates following warning messages.

intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]

This patch fixes this issue by adding extra check for resource size
before performing ioremap operation.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Variable byte_data is being initialized and re-assigned with values that
are never read. Remove these as these redundant assignments. Cleans up
clang warning:

drivers/platform/x86/dell-smo8800.c:106:2: warning: Value stored to 'byte_data'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Commit f9cf3b28 ("platform/x86: hp-wmi: Refactor dock and tablet
state fetchers") consolidated the methods for docking and laptop mode
detection, but omitted to apply the correct mask for the laptop mode
(it always uses the constant for docking).

Fixes: f9cf3b28 ("platform/x86: hp-wmi: Refactor dock and tablet state fetchers")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Moves timer structure off stack and
into struct ips_driver.

Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: platform-driver-x86@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The local variable "err" will eventually be set to an appropriate value
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Source code review for a specific software refactoring showed the need
for another correction because the error code "-1" was returned so far
if a call of the function "sony_call_snc_handle" failed here.
Thus assign the return value from these two function calls also to
the variable "err" and provide it in case of a failure.

Fixes: d6f15ed8 ("sony-laptop: use soft rfkill status stored in hw")
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lkml.org/lkml/2017/10/31/463
Link: https://lkml.kernel.org/r/<CAHp75VcMkXCioCzmLE0+BTmkqc5RSOx9yPO0ectVHMrMvewgwg@mail.gmail.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This application uses the character device /dev/wmi/dell-smbios
to perform SMBIOS communications from userspace.

It offers demonstrations of a few simple tasks:
 - Running a class/select command
 - Querying a token value
 - Activating a token
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

It's important for the driver to provide a R/W ioctl to ensure that
two competing userspace processes don't race to provide or read each
others data.

This userspace character device will be used to perform SMBIOS calls
from any applications.

It provides an ioctl that will allow passing the WMI calling
interface buffer between userspace and kernel space.

This character device is intended to deprecate the dcdbas kernel module
and the interface that it provides to userspace.

To perform an SMBIOS IOCTL call using the character device userspace will
perform a read() on the the character device.  The WMI bus will provide
a u64 variable containing the necessary size of the IOCTL buffer.

The API for interacting with this interface is defined in documentation
as well as the WMI uapi header provides the format of the structures.

Not all userspace requests will be accepted.  The dell-smbios filtering
functionality will be used to prevent access to certain tokens and calls.

All whitelisted commands and tokens are now shared out to userspace so
applications don't need to define them in their own headers.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

For WMI operations that are only Set or Query readable and writable sysfs
attributes created by WMI vendor drivers or the bus driver makes sense.

For other WMI operations that are run on Method, there needs to be a
way to guarantee to userspace that the results from the method call
belong to the data request to the method call.  Sysfs attributes don't
work well in this scenario because two userspace processes may be
competing at reading/writing an attribute and step on each other's
data.

When a WMI vendor driver declares a callback method in the wmi_driver
the WMI bus driver will create a character device that maps to that
function.  This callback method will be responsible for filtering
invalid requests and performing the actual call.

That character device will correspond to this path:
/dev/wmi/$driver

Performing read() on this character device will provide the size
of the buffer that the character device needs to perform calls.
This buffer size can be set by vendor drivers through a new symbol
or when MOF parsing is available by the MOF.

Performing ioctl() on this character device will be interpretd
by the WMI bus driver. It will perform sanity tests for size of
data, test them for a valid instance, copy the data from userspace
and pass iton to the vendor driver to further process and run.

This creates an implicit policy that each driver will only be allowed
a single character device.  If a module matches multiple GUID's,
the wmi_devices will need to be all handled by the same wmi_driver.

The WMI vendor drivers will be responsible for managing inappropriate
access to this character device and proper locking on data used by
it.

When a WMI vendor driver is unloaded the WMI bus driver will clean
up the character device and any memory allocated for the call.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

When a userspace interface is introduced to dell-smbios filtering
support will be used to make sure that userspace doesn't make calls
deemed unsafe or that can cause the kernel drivers to get out of
sync.

A blacklist is provided for the following:
- Items that are in use by other kernel drivers
- Items that are deemed unsafe (diagnostics, write-once, etc)
- Any items in the blacklist will be rejected.

Following that a whitelist is provided as follows:
- Each item has an associated capability.  If a userspace interface
  accesses this item, that capability will be tested to filter
  the request.
- If the process provides CAP_SYS_RAWIO the whitelist will be
  overridden.

When an item is not in the blacklist, or whitelist and the process
is run with insufficient capabilities the call will be rejected.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

WSMT is as an attestation to the OS that the platform won't
modify memory outside of pre-defined areas.

If a platform has WSMT enabled in BIOS setup, SMM calls through
dcdbas will fail.  The only way to access platform data in these
instances is through the WMI SMBIOS calling interface.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

The dell-smbios stack only currently uses an SMI interface which grants
direct access to physical memory to the firmware SMM methods via a pointer.

This dispatcher driver adds a WMI-ACPI interface that is detected by WMI
probe and preferred over the SMI interface in dell-smbios.

Changing this to operate over WMI-ACPI will use an ACPI OperationRegion
for a buffer of data storage when SMM calls are performed.

This is a safer approach to use in kernel drivers as the SMM will
only have access to that OperationRegion.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

This splits up the dell-smbios driver into two drivers:
* dell-smbios
* dell-smbios-smm

dell-smbios can operate with multiple different dispatcher drivers to
perform SMBIOS operations.

Also modify the interface that dell-laptop and dell-wmi use align to this
model more closely.  Rather than a single global buffer being allocated
for all drivers, each driver will allocate and be responsible for it's own
buffer. The pointer will be passed to the calling function and each
dispatcher driver will then internally copy it to the proper location to
perform it's call.

Add defines for calls used by these methods in the dell-smbios.h header
for tracking purposes.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Currently userspace tools can access system tokens via the dcdbas
kernel module and a SMI call that will cause the platform to execute
SMM code.

With a goal in mind of deprecating the dcdbas kernel module a different
method for accessing these tokens from userspace needs to be created.

This is intentionally marked to only be readable as a process with
CAP_SYS_ADMIN as it can contain sensitive information about the
platform's configuration.

While adding this interface I found that some tokens are duplicated.
These need to be ignored from sysfs to avoid duplicate files.

MAINTAINERS was missing for this driver.  Add myself and Pali to
maintainers list for it.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

The proper way to indicate that a system is a 'supported' Dell System
is by the presence of this string in OEM strings.

Allowing the driver to load on non-Dell systems will have undefined
results.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

The only driver using this was dell-wmi, and it really was a hack.
The driver was getting a data attribute from another driver and this
type of action should not be encouraged.

Rather drivers that need to interact with one another should pass
data back and forth via exported functions.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

All communication on individual GUIDs should occur in separate drivers.
Allowing a driver to communicate with the bus to another GUID is just
a hack that discourages drivers to adopt the bus model.

The information found from the WMI descriptor driver is now exported
for use by other drivers.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

This is intended to be variable and provided by the platform.
Some platforms this year will be adopting a 32k WMI buffer, so don't
complain when encountering those platforms or any other future changes.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Some cases the wrong type was used for errors and checks can be
done more cleanly.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

There is a lot of error checking in place for the format of the WMI
descriptor buffer, but some of the potentially raised issues should
be considered critical failures.

If the buffer size or header don't match, this is a good indication
that the buffer format changed in a way that the rest of the data
should not be relied upon.

For the remaining data set vectors, continue to notate a warning
in undefined results, but as those are fields that the descriptor
intended to refer to other applications, don't fail if they're new
values.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Drivers properly using the wmibus can pass their wmi_device
pointer rather than the GUID back to the WMI bus to evaluate
the proper methods.

Any "new" drivers added that use the WMI bus should use this
rather than the old wmi_evaluate_method that would take the
GUID.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Later on these structures will be brought up to userspace.
the word "class" is a reserved word in c++ and this will prevent
uapi headers from being included directly in c++ programs.

To make life easier on these applications, prepare the change now.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

The fusb302 driver as merged in staging uses "typec_fusb302" as i2c-id
rather then just "fusb302" and needs us to set a number of device-
properties, adjust the intel_cht_int33fe driver accordingly.

One of the properties set is max-snk-mv which makes the fusb302 driver
negotiate up to 12V charging voltage, which is a bad idea on boards
which are not setup to handle this, so this commit also adds 2 extra
sanity checks to make sure that the expected Whiskey Cove PMIC +
TI bq24292i charger combo, which can handle 12V, is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Merge branch 'i2c/cht-wc-fusb302-immutable' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c/cht-wc-fusb302-immutable immutable branch from Wolfram Sang:

as discussed before, here is the immutable branch for the i2c-cht-wc
driver, so you can safely apply Hans' patch [1]

"platform/x86: intel_cht_int33fe: Update fusb302 type string, add properties"

on top of this.

[1] http://patchwork.ozlabs.org/patch/824314/

Add touchscreen platform data for the Digma e200 tablet.
Signed-off-by: Sergey Tshovrebov <sinxwal@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The GP-electronic T701 has its LCD panel mounted upside-down, initially
my plan was to fix this by transparently rotating the image in the i915
driver (my "drm/i915: Deal with upside-down mounted LCD" patch), but
that approach has been rejected instead the kernel will now export
a "panel orientation" property on the drm-connector for the panel and
let userspace deal with it.

But userspace expects the touchscreen coordinates to match the panel
coordinates *before* applying any rotation, so now that we no longer hide
the upside-down-ness of the LCD panel from userspace the coordinates being
generated are wrong and we need to apply a rotation of 180 degrees to the
coordinates to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

peaq_wmi_exit will only ever get called if peaq_wmi_init succeeds, so
there is no need to repeat the checks from peaq_wmi_init.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add missing terminating entry to peaq_dmi_table.

Fixes: 3b952061 ("platform/x86: peaq-wmi: Add DMI check before ...")
Cc: stable@vger.kernel.org
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The Lenovo Yoga 920-13IKB does not have a hw rfkill switch, and trying
to read the hw rfkill switch through the ideapad module causes it to
always report as blocked.

This commit adds the Lenovo Yoga 920-13IKB to the no_hw_rfkill dmi list,
fixing the WiFI breakage.
Signed-off-by: Philipp Hug <philipp@hug.cx>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Radio LED detection method implemented in commit 4f62568c
("fujitsu-laptop: Support radio LED") turned out to be incorrect as it
causes a radio LED to be erroneously detected on a Fujitsu Lifebook E751
which has a slide switch (and thus no radio LED).  Use bit 17 of
flags_supported (the value returned by method S000 of ACPI device
FUJ02E3) to determine whether a radio LED is present as it seems to be a
more reliable indicator, based on comparing DSDT tables of four Fujitsu
Lifebook models (E744, E751, S7110, S8420).

Fixes: 4f62568c ("fujitsu-laptop: Support radio LED")
Reported-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Added support for HP ProBook 440 G4 laptops by including the accelerometer
orientation quirk for that device. Testing was performed based on the
axis orientation guidelines here:
https://www.kernel.org/doc/Documentation/misc-devices/lis3lv02d
which states "If the left side is elevated, X increases (becomes positive)".

When tested, on lifting the left edge, x values became increasingly negative
thus indicating an inverted x-axis on the installed lis3lv02d chip.
This was compensated by adding an entry for this device in hp_accel.c
specifying the quirk as x_inverted. The patch was tested on a
ProBook 440 G4 device and x-axis as well as y and z-axis values are now
generated as per spec.
Signed-off-by: Osama Khan <osama.khan@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Ev Kontsevoy reported that he can't see the presence of
"/proc/sys/kernel/sched_itmt_enabled" on i9-7900x with Asrock x299
Taichi system even if he enabled "Turbo 3.0" in the BIOS.

The problem is that even if one core max is 200MHz more than others, the
current implementation couldn't enumerate that with the way the system
is configured.

The system by default configured for legacy mode (no HWP or speed shift
technology), in this mode only way we can enumerate via the mail box
interface as implemented in this driver. We were planing to only use
this driver for Broadwell, but we need to extend this because some
Skylake system has same issue as Braodwell systems.

On this system BIOS allows to change to HWP mode, where we expect that
we can enumerate favored core with ACPI-CPPC. But on this system the
core priority is 0xff for all cores in CPPC object. So this is not an
option.

Hence this change allows Skylake systems to be enumerate favored core
similar to Broadwell in legacy mode.
Reported-and-tested-by: Ev Kontsevoy <ev@kontsevoy.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

'default n' is a default behaviour of Kconfig options. So, remove
explicit line from Kconfig.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

linux/io.h defines readq() and ioremap_nocache() / iounmap() functions.

If not included, the build fails:

intel_telemetry_pltdrv.c:1165:31: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
intel_telemetry_pltdrv.c:1165:33: error: implicit declaration of function 'ioremap_nocache' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:1202:3: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:900:20: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]

Fix this by including linux/io.h.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add device-properties to make the bq24292i charger connected to
the bus get its input-current-limit from the fusb302 Type-C port
controller which is used on boards with the cht-wc PMIC,
as well as regulator_init_data for the 5V boost converter on
the bq24292i.

Since this means we now hook-up the bq24292i to the fusb302 Type-C port
controller add a check for the ACPI device which instantiates the fusb302.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

For devices not instantiated through ACPI the i2c-client's device-name
gets set to <busnr>-<addr> by default, e.g. "0-0022" this means that
the device-name is dependent on the order in which the i2c-busses are
enumerated.

In some cases having a predictable constant device-name is desirable,
for example on non device-tree platforms the link between a regulator
and its consumers is specified by the platform code by setting
regulator_init_data.consumers. This array identifies the regulator's
consumers by dev_name and supply(-name). Which requires a constant
dev_name.

This commit adds a dev_name field to i2c_board_info allowing
platform code to set a contstant dev_name so that the device can
be identified by its dev_name in other platform code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org> (live at ELCE17)
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (live at ELCE17)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently, update_no_reboot_bit() function implemented in this driver
uses mutex_lock() to protect its register updates. But this function is
called with in atomic context in iTCO_wdt_start() and iTCO_wdt_stop()
functions in iTCO_wdt.c driver, which in turn causes "sleeping into
atomic context" issue. This patch fixes this issue by replacing the
mutex_lock() with spin_lock() to protect the GCR read/write/update APIs.

Fixes: 9d855d46 ("platform/x86: intel_pmc_ipc: Fix iTCO_wdt GCS memory mapping failure")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kupuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Removes unnecessary header files included in the driver and sorts the
remaining ones in the alphabetical order.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Telemetry word is misspelled several times in this file as Telemtry. This
fixes the spelling mistake and folds in another minor typo.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Intel Telemetry driver depends on IPC1 interface. If IPC1 interface is
disabled on a given platform by the system firmware, the driver does not
load but prints misleading information in the dmesg logs.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>