Current description of the compatible property for at24 is quite vague.

State explicitly that any "<manufacturer>,<model>" pair is accepted as
long as a correct fallback is used for non-atmel chips.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Rob Herring <robh@kernel.org>

Replace spaces with tabs in the definition of AT24_FLAG_NO_RDROL.

Fixes: 9d404411091c ("eeprom: at24: support eeproms that do not auto-rollover reads")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).

On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.

Make the driver check if the write-protect GPIO was defined in the
device tree and pull it low whenever writing to the EEPROM.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).

On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.

Add a new optional property to the device tree binding document, which
allows to specify the GPIO line to which the write-protect pin is
connected.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>

The chip size passed via devicetree, i2c, or acpi device ids is now no
longer limited to a power of two. So the temporary fix can be removed.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Fundamental properties such as capacity and page size differ among
at24-type chips. But these chips do not have an id register, so this
can't be discovered at runtime.

Traditionally, at24-type eeprom properties were determined in two ways:
- by passing a 'struct at24_platform_data' via platform_data, or
- by naming the chip type in the devicetree, which passes a 'magic
  number' to probe(), which is then converted to a 'struct
  at24_platform_data'.

Recently a bug was discovered because the magic number rounds down all
chip sizes to the lowest power of two. This was addressed by
a work-around commit 5478e478 ("eeprom: at24: correctly set the
size for at24mac402"), with the wish that magic numbers should over
time be converted to structs.

This patch replaces the magic numbers with 'struct at24_chip_data'.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

A regmap_config struct is pretty big and declaring two of them
statically just to tweak the reg_bits value adds unnecessary bloat.

Declare the regmap config locally in at24_probe() instead.

Bloat-o-meter output for ARM:

add/remove: 0/2 grow/shrink: 1/0 up/down: 4/-272 (-268)
Function                                     old     new   delta
at24_probe                                  1560    1564      +4
regmap_config_8                              136       -    -136
regmap_config_16                             136       -    -136
Total: Before=7012, After=6744, chg -3.82%
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

There are a couple symbols defined in the driver source file which are
missing the at24_ prefix. This patch fixes that.

For module params: use module_param_named() in order to not break
userspace.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Fix issues reported by checkpatch for at24.c.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add the link to my git tree to the at24 section.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Some multi-address eeproms in the at24 family may not automatically
roll-over reads to the next slave address. On those eeproms, reads
that straddle slave boundaries will not work correctly.

Solution:
Mark such eeproms with a flag that prevents reads straddling
slave boundaries. Add the AT24_FLAG_NO_RDROL flag to the eeprom
entry in the device_id table, or add 'no-read-rollover' to the
eeprom devicetree entry.

Note that I have not personally enountered an at24 chip that
does not support read rollovers. They may or may not exist.
However, my hardware requires this functionality because of
a quirk.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Adds an optional property for at24 eeproms. This parameterless
property indicates that the multi-address eeprom does not
automatically roll over reads to the next slave address.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The driver gained DT support recently, so we should add the binding docs
in the MAINTAINERS file.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

This binding documentation is for the at24 driver, so the filename
should reflect it. This avoids confusion because we also have an
"eeprom" driver in Linux but it doesn't support DT even.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Remove remaining now unneeded code dealing with SMBUS details.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Remove the old and now unused read functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add regmap-based read function and instead of using three different
read functions (standard, mac, serial) use just one and factor out the
read offset adjustment for mac and serial to at24_adjust_read_offset.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Remove the old and now unused write functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add a regmap-based write function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Change return type of at24_translate_offset to *at24_client to make
member regmap accessible for subsequent patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

This patch adds basic regmap support to be used by subsequent
patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixlets for x86:

   - Fix the ESPFIX double fault handling for 5-level pagetables

   - Fix the commandline parsing for 'apic=' on 32bit systems and update
     documentation

   - Make zombie stack traces reliable

   - Fix kexec with stack canary

   - Fix the delivery mode for APICs which was missed when the x86
     vector management was converted to single target delivery. Caused a
     regression due to the broken hardware which ignores affinity
     settings in lowest prio delivery mode.

   - Unbreak modules when AMD memory encryption is enabled

   - Remove an unused parameter of prepare_switch_to"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Switch all APICs to Fixed delivery mode
  x86/apic: Update the 'apic=' description of setting APIC driver
  x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case
  x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR)
  x86: Remove unused parameter of prepare_switch_to
  x86/stacktrace: Make zombie stack traces reliable
  x86/mm: Unbreak modules that use the DMA API
  x86/build: Make isoimage work on Debian
  x86/espfix/64: Fix espfix double-fault handling on 5-level systems

Pull x86 page table isolation fixes from Thomas Gleixner:
 "Four patches addressing the PTI fallout as discussed and debugged
  yesterday:

   - Remove stale and pointless TLB flush invocations from the hotplug
     code

   - Remove stale preempt_disable/enable from __native_flush_tlb()

   - Plug the memory leak in the write_ldt() error path"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ldt: Make LDT pgtable free conditional
  x86/ldt: Plug memory leak in error path
  x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()
  x86/smpboot: Remove stale TLB flush invocations

Pull timer fixes from Thomas Gleixner:
 "A pile of fixes for long standing issues with the timer wheel and the
  NOHZ code:

   - Prevent timer base confusion accross the nohz switch, which can
     cause unlocked access and data corruption

   - Reinitialize the stale base clock on cpu hotplug to prevent subtle
     side effects including rollovers on 32bit

   - Prevent an interrupt storm when the timer softirq is already
     pending caused by tick_nohz_stop_sched_tick()

   - Move the timer start tracepoint to a place where it actually makes
     sense

   - Add documentation to timerqueue functions as they caused confusion
     several times now"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timerqueue: Document return values of timerqueue_add/del()
  timers: Invoke timer_start_debug() where it makes sense
  nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()
  timers: Reinitialize per cpu bases on hotplug
  timers: Use deferrable base independent of base::nohz_active

Pull smp fixlet from Thomas Gleixner:
 "A trivial build warning fix for newer compilers"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Move inline keyword at the beginning of declaration

Pull scheduler fixes from Thomas Gleixner:
 "Three patches addressing the fallout of the CPU_ISOLATION changes
  especially with NO_HZ_FULL plus documentation of boot parameter
  dependency"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/isolation: Document boot parameters dependency on CONFIG_CPU_ISOLATION=y
  sched/isolation: Enable CONFIG_CPU_ISOLATION=y by default
  sched/isolation: Make CONFIG_NO_HZ_FULL select CONFIG_CPU_ISOLATION

Pull perf fixes from Thomas Gleixner:

 - plug a memory leak in the intel pmu init code

 - clang fixes

 - tooling fix to avoid including kernel headers

 - a fix for jvmti to generate correct debug information for inlined
   code

 - replace backtick with a regular shell function

 - fix the build in hardened environments

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Plug memory leak in intel_pmu_init()
  x86/asm: Allow again using asm.h when building for the 'bpf' clang target
  tools arch s390: Do not include header files from the kernel sources
  perf jvmti: Generate correct debug information for inlined code
  perf tools: Fix up build in hardened environments
  perf tools: Use shell function for perl cflags retrieval

Pull irq fixes from Thomas Gleixner:
 "A rather large update after the kaisered maintainer finally found time
  to handle regression reports.

   - The larger part addresses a regression caused by the x86 vector
     management rework.

     The reservation based model does not work reliably for MSI
     interrupts, if they cannot be masked (yes, yet another hw
     engineering trainwreck). The reason is that the reservation mode
     assigns a dummy vector when the interrupt is allocated and switches
     to a real vector when the interrupt is requested.

     If the MSI entry cannot be masked then the initialization might
     raise an interrupt before the interrupt is requested, which ends up
     as spurious interrupt and causes device malfunction and worse. The
     fix is to exclude MSI interrupts which do not support masking from
     reservation mode and assign a real vector right away.

   - Extend the extra lockdep class setup for nested interrupts with a
     class for the recently added irq_desc::request_mutex so lockdep can
     differeniate and does not emit false positive warnings.

   - A ratelimit guard for the bad irq printout so in case a bad irq
     comes back immediately the system does not drown in dmesg spam"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
  genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
  x86/vector: Use IRQD_CAN_RESERVE flag
  genirq: Introduce IRQD_CAN_RESERVE flag
  genirq/msi: Handle reactivation only on success
  gpio: brcmstb: Make really use of the new lockdep class
  genirq: Guard handle_bad_irq log messages
  kernel/irq: Extend lockdep class for request mutex

Pull objtool fixes from Thomas Gleixner:
 "Three fixlets for objtool:

   - Address two segfaults related to missing parameter and clang
     objects

   - Make it compile clean with clang"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with clang-compiled objects
  objtool: Fix seg fault caused by missing parameter
  objtool: Fix Clang enum conversion warning

Pull char/misc fixes from Greg KH:
 "Here are six small fixes of some of the char/misc drivers that have
  been sent in to resolve reported issues.

  Nothing major, a binder use-after-free fix, some thunderbolt bugfixes,
  a hyper-v bugfix, and an nvmem driver fix. All of these have been in
  linux-next with no reported issues for a while"

* tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  nvmem: meson-mx-efuse: fix reading from an offset other than 0
  binder: fix proc->files use-after-free
  vmbus: unregister device_obj->channels_kset
  thunderbolt: Mask ring interrupt properly when polling starts
  MAINTAINERS: Add thunderbolt.rst to the Thunderbolt driver entry
  thunderbolt: Make pathname to force_power shorter

Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are two driver core fixes for 4.15-rc6, resolving some reported
  issues.

  The first is a cacheinfo fix for DT based systems to resolve a
  reported issue that has been around for a while, and the other is to
  resolve a regression in the kobject uevent code that showed up in
  4.15-rc1.

  Both have been in linux-next for a while with no reported issues"

* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kobject: fix suppressing modalias in uevents delivered over netlink
  drivers: base: cacheinfo: fix cache type for non-architected system cache

Pull staging fixes from Greg KH:
 "Here are three staging driver fixes for 4.15-rc6

  The first resolves a bug in the lustre driver that came about due to a
  broken cleanup patch, due to crazy list usage in that codebase.

  The remaining two are ion driver fixes, finally getting the CMA
  interaction to work properly, resolving two regressions in that area
  of the code.

  All have been in linux-next with no reported issues for a while"

* tag 'staging-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: android: ion: Fix dma direction for dma_sync_sg_for_cpu/device
  staging: ion: Fix ion_cma_heap allocations
  staging: lustre: lnet: Fix recent breakage from list_for_each conversion

Pull TTY fix from Greg KH:
 "Here is a single tty fix for a reported issue that you wrote the patch
  for :)

  It's been in linux-next for a week or so with no reported issues"

* tag 'tty-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  n_tty: fix EXTPROC vs ICANON interaction with TIOCINQ (aka FIONREAD)

Pull USB/PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.15-rc6.

  Nothing major, but there are a number of regression fixes in here that
  resolve issues that have been reported a bunch. There are also the
  usual xhci fixes as well as a number of new usb serial device ids.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: xhci: Add XHCI_TRUST_TX_LENGTH for Renesas uPD720201
  xhci: Fix use-after-free in xhci debugfs
  xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate
  USB: serial: ftdi_sio: add id for Airbus DS P8GR
  usb: Add device quirk for Logitech HD Pro Webcam C925e
  usb: add RESET_RESUME for ELSA MicroLink 56K
  usbip: fix usbip bind writing random string after command in match_busid
  usbip: stub_rx: fix static checker warning on unnecessary checks
  usbip: prevent leaking socket pointer address in messages
  usbip: stub: stop printing kernel pointer addresses in messages
  usbip: vhci: stop printing kernel pointer addresses in messages
  USB: Fix off by one in type-specific length check of BOS SSP capability
  USB: serial: option: adding support for YUGA CLM920-NC5
  phy: rcar-gen3-usb2: select USB_COMMON
  phy: rockchip-typec: add pm_runtime_disable in err case
  phy: cpcap-usb: Fix platform_get_irq_byname's error checking.
  phy: tegra: fix device-tree node lookups
  USB: serial: qcserial: add Sierra Wireless EM7565
  USB: serial: option: add support for Telit ME910 PID 0x1101
  USB: chipidea: msm: fix ulpi-node lookup

The blackfin architecture has seen no maintainer action of any kind since
April 2015.  No new code, no pull requests, no acks to patches, no response
to mails, nothing.

The web site has an expired certificate (expiration Sep 2017, issued in
2013), the mailing list sees no answers either, with one exception:

  https://sourceforge.net/p/adi-buildroot/mailman/adi-buildroot-devel/
  >
  > Steven is no longer working on this for ADI. Acked by me if this works. Thanks.
  >
  > Best regards,
  > Aaron Wu
  > Analog Devices Inc.

But, Aaron doesn't seem to respond to queries either.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sparc bugfix from David Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: repair calling incorrect hweight function from stubs

Andy prefers to be paranoid about the pagetable free in the error path of
write_ldt(). Make it conditional and warn whenever the installment of a
secondary LDT fails.
Requested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The error path in write_ldt() tries to free 'old_ldt' instead of the newly
allocated 'new_ldt', resulting in a memory leak. It also misses to clean up a
half populated LDT pagetable, which is not a leak as it gets cleaned up
when the process exits.

Free both the potentially half populated LDT pagetable and the newly
allocated LDT struct. This can be done unconditionally because once an LDT
is mapped subsequent maps will succeed, because the PTE page is already
populated and the two LDTs fit into that single page.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: f55f0501 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1712311121340.1899@nanosSigned-off-by: Ingo Molnar <mingo@kernel.org>

The preempt_disable/enable() pair in __native_flush_tlb() was added in
commit:

  5cf0791d ("x86/mm: Disable preemption during CR3 read+write")

... to protect the UP variant of flush_tlb_mm_range().

That preempt_disable/enable() pair should have been added to the UP variant
of flush_tlb_mm_range() instead.

The UP variant was removed with commit:

  ce4a4e56 ("x86/mm: Remove the UP asm/tlbflush.h code, always use the (formerly) SMP code")

... but the preempt_disable/enable() pair stayed around.

The latest change to __native_flush_tlb() in commit:

  6fd166aa ("x86/mm: Use/Fix PCID to optimize user/kernel switches")

... added an access to a per CPU variable outside the preempt disabled
regions, which makes no sense at all. __native_flush_tlb() must always
be called with at least preemption disabled.

Remove the preempt_disable/enable() pair and add a WARN_ON_ONCE() to catch
bad callers independent of the smp_processor_id() debugging.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171230211829.679325424@linutronix.deSigned-off-by: Ingo Molnar <mingo@kernel.org>