Default rlimit RLIMIT_MEMLOCK is 64KB, causes bpf map failure.
e.g.
[root@lab bpf]#./xdp1 -N $(</sys/class/net/eth2/ifindex)
failed to create a map: 1 Operation not permitted

Fix it.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcm_sf2 and b53 replicate the same operations: clear all VLANs and set
their ports to the default VLAN tag (1 for these devices) so export the
b53 function doing just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creating a macvtap interface with the liquidio VF driver as lower device
causes this alarming message to show up in dmesg:

    liquidio_link_ctrl_cmd_completion Unknown cmd 27

That's actually a false alarm because cmd 27 is the value of the macro
OCTNET_CMD_SET_UC_LIST which is known.  It's a control command sent from
host to NIC firmware to set the unicast MAC address list of the macvtap
lower device.

Make the false alarm go away by adding a case for OCTNET_CMD_SET_UC_LIST
in liquidio_link_ctrl_cmd_completion().
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases, like internal vSwitch, the host doesn't provide
send indirection table updates. This patch sets the table to be
equal weight after subchannels are all open. Otherwise, all workload
will be on one TX channel.

As tested, this patch has largely increased the throughput over
internal vSwitch.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for CAP_NET_ADMIN with ns_capable() instead of capable()
to allow usage of ppp in user namespace other than the init one.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2017-10-27

This patchset is a proposal of how the Traffic Control subsystem can
be used to offload the configuration of the Credit Based Shaper
(defined in the IEEE 802.1Q-2014 Section 8.6.8.2) into supported
network devices.

As part of this work, we've assessed previous public discussions
related to TSN enabling: patches from Henrik Austad (Cisco), the
presentation from Eric Mann at Linux Plumbers 2012, patches from
Gangfeng Huang (National Instruments) and the current state of the
OpenAVNU project (https://github.com/AVnu/OpenAvnu/).

Overview
========

Time-sensitive Networking (TSN) is a set of standards that aim to
address resources availability for providing bandwidth reservation and
bounded latency on Ethernet based LANs. The proposal described here
aims to cover mainly what is needed to enable the following standards:
802.1Qat and 802.1Qav.

The initial target of this work is the Intel i210 NIC, but other
controllers' datasheet were also taken into account, like the Renesas
RZ/A1H RZ/A1M group and the Synopsis DesignWare Ethernet QoS
controller.

Proposal
========

Feature-wise, what is covered here is the configuration interfaces for
HW implementations of the Credit-Based shaper (CBS, 802.1Qav). CBS is
a per-queue shaper. Given that this feature is related to traffic
shaping, and that the traffic control subsystem already provides a
queueing discipline that offloads config into the device driver (i.e.
mqprio), designing a new qdisc for the specific purpose of offloading
the config for the CBS shaper seemed like a good fit.

For steering traffic into the correct queues, we use the socket option
SO_PRIORITY and then a mechanism to map priority to traffic classes /
Tx queues. The qdisc mqprio is currently used in our tests.

As for the CBS config interface, this patchset is proposing a new
qdisc called 'cbs'. Its 'tc' cmd line is:

$ tc qdisc add dev IFACE parent ID cbs locredit N hicredit M sendslope S \
     idleslope I

   Note that the parameters for this qdisc are the ones defined by the
   802.1Q-2014 spec, so no hardware specific functionality is exposed here.

Per-stream shaping, as defined by IEEE 802.1Q-2014 Section 34.6.1, is
not yet covered by this proposal.

v2: Merged patch 6 of the original series into patch 4 based on feedback
    from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
l2tp: register sessions atomically

Currently l2tp_session_create() allocates a session, partially
initialises it and finally registers it. It therefore exposes sessions
that aren't fully initialised to the rest of the system, because
pseudo-wire specific initialisation can only happen after
l2tp_session_create() returns.
This leads to several crashes when these sessions are used or deleted.

This series starts by splitting session registration out of
l2tp_session_create() (patch #1). Thus allowing pseudo-wires code to
terminate the initialisation phase before registration.

Then patch #2 fixes the eth pseudo-wire code. This requires protecting
the session's netdevice pointer with RCU, because it still needs to be
updated concurrently after the session got registered.

Remaining patches take care of ppp pseudo-wires. RCU protection is
needed there too, for the same reasons. This time it's the pppol2tp
socket pointer that gets protected. For clarity, and since the
conversion requires more modifications, introducing RCU is done in
its own patch (#3). Then patch #4 only has to take care of fixing
sessions initialisation and registration (and adapting part of the
deletion process).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

pppol2tp_connect() initialises L2TP sessions after they've been exposed
to the rest of the system by l2tp_session_register(). This puts
sessions into transient states that are the source of several races, in
particular with session's deletion path.

This patch centralises the initialisation code into
pppol2tp_session_init(), which is called before the registration phase.
The only field that can't be set before session registration is the
pppol2tp socket pointer, which has already been converted to RCU. So
pppol2tp_connect() should now be race-free.

The session's .session_close() callback is now set before registration.
Therefore, it's always called when l2tp_core deletes the session, even
if it was created by pppol2tp_session_create() and hasn't been plugged
to a pppol2tp socket yet. That'd prevent session free because the extra
reference taken by pppol2tp_session_close() wouldn't be dropped by the
socket's ->sk_destruct() callback (pppol2tp_session_destruct()).
We could set .session_close() only while connecting a session to its
pppol2tp socket, or teach pppol2tp_session_close() to avoid grabbing a
reference when the session isn't connected, but that'd require adding
some form of synchronisation to be race free.

Instead of that, we can just let the pppol2tp socket hold a reference
on the session as soon as it starts depending on it (that is, in
pppol2tp_connect()). Then we don't need to utilise
pppol2tp_session_close() to hold a reference at the last moment to
prevent l2tp_core from dropping it.

When releasing the socket, pppol2tp_release() now deletes the session
using the standard l2tp_session_delete() function, instead of merely
removing it from hash tables. l2tp_session_delete() drops the reference
the sessions holds on itself, but also makes sure it doesn't remove a
session twice. So it can safely be called, even if l2tp_core already
tried, or is concurrently trying, to remove the session.
Finally, pppol2tp_session_destruct() drops the reference held by the
socket.

Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

pppol2tp_session_create() registers sessions that can't have their
corresponding socket initialised. This socket has to be created by
userspace, then connected to the session by pppol2tp_connect().
Therefore, we need to protect the pppol2tp socket pointer of L2TP
sessions, so that it can safely be updated when userspace is connecting
or closing the socket. This will eventually allow pppol2tp_connect()
to avoid generating transient states while initialising its parts of the
session.

To this end, this patch protects the pppol2tp socket pointer using RCU.

The pppol2tp socket pointer is still set in pppol2tp_connect(), but
only once we know the function isn't going to fail. It's eventually
reset by pppol2tp_release(), which now has to wait for a grace period
to elapse before it can drop the last reference on the socket. This
ensures that pppol2tp_session_get_sock() can safely grab a reference
on the socket, even after ps->sk is reset to NULL but before this
operation actually gets visible from pppol2tp_session_get_sock().

The rest is standard RCU conversion: pppol2tp_recv(), which already
runs in atomic context, is simply enclosed by rcu_read_lock() and
rcu_read_unlock(), while other functions are converted to use
pppol2tp_session_get_sock() followed by sock_put().
pppol2tp_session_setsockopt() is a special case. It used to retrieve
the pppol2tp socket from the L2TP session, which itself was retrieved
from the pppol2tp socket. Therefore we can just avoid dereferencing
ps->sk and directly use the original socket pointer instead.

With all users of ps->sk now handling NULL and concurrent updates, the
L2TP ->ref() and ->deref() callbacks aren't needed anymore. Therefore,
rather than converting pppol2tp_session_sock_hold() and
pppol2tp_session_sock_put(), we can just drop them.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sessions must be initialised before being made externally visible by
l2tp_session_register(). Otherwise the session may be concurrently
deleted before being initialised, which can confuse the deletion path
and eventually lead to kernel oops.

Therefore, we need to move l2tp_session_register() down in
l2tp_eth_create(), but also handle the intermediate step where only the
session or the netdevice has been registered.

We can't just call l2tp_session_register() in ->ndo_init() because
we'd have no way to properly undo this operation in ->ndo_uninit().
Instead, let's register the session and the netdevice in two different
steps and protect the session's device pointer with RCU.

And now that we allow the session's .dev field to be NULL, we don't
need to prevent the netdevice from being removed anymore. So we can
drop the dev_hold() and dev_put() calls in l2tp_eth_create() and
l2tp_eth_dev_uninit().

Fixes: d9e31d17 ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sessions created by l2tp_session_create() aren't fully initialised:
some pseudo-wire specific operations need to be done before making the
session usable. Therefore the PPP and Ethernet pseudo-wires continue
working on the returned l2tp session while it's already been exposed to
the rest of the system.
This can lead to various issues. In particular, the session may enter
the deletion process before having been fully initialised, which will
confuse the session removal code.

This patch moves session registration out of l2tp_session_create(), so
that callers can control when the session is exposed to the rest of the
system. This is done by the new l2tp_session_register() function.

Only pppol2tp_session_create() can be easily converted to avoid
modifying its session after registration (the debug message is dropped
in order to avoid the need for holding a reference on the session).

For pppol2tp_connect() and l2tp_eth_create()), more work is needed.
That'll be done in followup patches. For now, let's just register the
session right after its creation, like it was done before. The only
difference is that we can easily take a reference on the session before
registering it, so, at least, we're sure it's not going to be freed
while we're working on it.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This causes build failures:

In file included from net/ipv4/tcp_input.c:79:0:
./include/linux/unaligned/access_ok.h:7:28: error: redefinition of
'get_unaligned_le16'
In file included from ./include/asm-generic/unaligned.h:17:0,
                 from ./arch/arm/include/generated/asm/unaligned.h:1,
                 from net/ipv4/tcp_input.c:76:
./include/linux/unaligned/le_struct.h:6:19: note: previous definition
of 'get_unaligned_le16' was here
In file included from net/ipv4/tcp_input.c:79:0:
./include/linux/unaligned/access_ok.h:12:28: error: redefinition of
'get_unaligned_le32'

Plain "asm/access_ok.h", which is already included, is
sufficient.

Fixes: 60e2a778 ("tcp: TCP experimental option for SMC")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds checks at approprate places whether *dma_map*() call has
succeeded or not.

Original Work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kirr: In particular with

	ethtool -C <ifname> rx-usecs 0 rx-frames 0

now it is possible to disable RX delays when NIC usage requires low-latency.

See this thread for context:

	https://www.spinics.net/lists/netdev/msg217665.html

My specific case is that:

We have many computers with gigabit Realtek NICs. For 2 such computers
connected to a gigabit store-and-forward switch the minimum round-trip
time for small pings (`ping -i 0 -w 3 -s 56 -q peer`) is ~ 30μs.

However it turned out that when Ethernet frame length transitions 127 ->
128 bytes (`ping -i 0 -w 3 -s {81 -> 82} -q peer`) the lowest RTT
transitions step-wise to ~ 270μs.

As David Light said this is RX interrupt mitigation done by NIC which creates
the latency. For workloads when low-latency is required with e.g. Intel,
BCM etc NIC drivers one just uses `ethtool -C rx-usecs ...` to reduce
the time NIC delays before interrupting CPU, but it turned out
`ethtool -C` is not supported by r8169 driver.

Like Stéphane ANCELOT I've traced the problem down to IntrMitigate being
hardcoded to != 0 for our chips (we have 8168 based NICs):

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/realtek/r8169.c#n5460
static void rtl_hw_start_8169(struct net_device *dev) {
        ...
        /*
         * Undocumented corner. Supposedly:
         * (TxTimer << 12) | (TxPackets << 8) | (RxTimer << 4) | RxPackets
         */
        RTL_W16(IntrMitigate, 0x0000);

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/realtek/r8169.c#n6346
static void rtl_hw_start_8168(struct net_device *dev) {
        ...
        RTL_W16(IntrMitigate, 0x5151);

and then I've also found

	https://www.spinics.net/lists/netdev/msg217665.html

and original Francois' patch:

	https://www.spinics.net/lists/netdev/msg217984.html
	https://www.spinics.net/lists/netdev/msg218207.html

So could we please finally get support for tuning r8169 interrupt
coalescing in tree? (so that next poor soul who hits the problem does
not need to go all the way to dig into driver sources and internet
wildly and finally patch locally

        -RTL_W16(IntrMitigate, 0x5151);
        +RTL_W16(IntrMitigate, 0x5100);

guessing whether it is right or not and also having to care to deploy
the patch everywhere it needs to be used, etc...).

To do so I've took original Francois's patch from 2012 and reworked it a bit:

- updated to latest net-next.git;
- adjusted scaling setup based on feedback from Hayes to pick up scaling
  vector depending not only on link speed but also on CPlusCmd[0:1] and to
  adjust CPlusCmd[0:1] correspondingly when setting timings;
- improved a bit (I think so) error handling.

I've tested the patch on "RTL8168d/8111d" (XID 083000c0) and with it and
`ethtool -C rx-usecs 0 rx-frames 0` on both ends it improves:

- minimum RTT latency:

        ~270μs ->  ~30μs (small packet),
        ~330μs -> ~110μs (full 1.5K ethernet frame)

- average RTT latency:

        ~480μs ->  ~50μs (small packet),
        ~560μs -> ~125μs (full 1.5K ethernet frame)

( before:

        root@neo1:# ping -i 0 -w 3 -s 82 -q neo2
        PING neo2.kirr.nexedi.com (192.168.102.21) 82(110) bytes of data.

        --- neo2.kirr.nexedi.com ping statistics ---
        5906 packets transmitted, 5905 received, 0% packet loss, time 2999ms
        rtt min/avg/max/mdev = 0.274/0.485/0.607/0.026 ms, ipg/ewma 0.508/0.489 ms

        root@neo1:# ping -i 0 -w 3 -s 1472 -q neo2
        PING neo2.kirr.nexedi.com (192.168.102.21) 1472(1500) bytes of data.

        --- neo2.kirr.nexedi.com ping statistics ---
        5073 packets transmitted, 5073 received, 0% packet loss, time 2999ms
        rtt min/avg/max/mdev = 0.330/0.566/0.710/0.028 ms, ipg/ewma 0.591/0.544 ms

  after:

        root@neo1# ping -i 0 -w 3 -s 82 -q neo2
        PING neo2.kirr.nexedi.com (192.168.102.21) 82(110) bytes of data.

        --- neo2.kirr.nexedi.com ping statistics ---
        45815 packets transmitted, 45815 received, 0% packet loss, time 3000ms
        rtt min/avg/max/mdev = 0.036/0.051/0.368/0.010 ms, ipg/ewma 0.065/0.053 ms

        root@neo1:# ping -i 0 -w 3 -s 1472 -q neo2
        PING neo2.kirr.nexedi.com (192.168.102.21) 1472(1500) bytes of data.

        --- neo2.kirr.nexedi.com ping statistics ---
        21250 packets transmitted, 21250 received, 0% packet loss, time 3000ms
        rtt min/avg/max/mdev = 0.112/0.125/0.390/0.007 ms, ipg/ewma 0.141/0.125 ms

  the small -> 1.5K latency growth is understandable as it takes ~15μs
  to transmit 1.5K on 1Gbps on the wire and with 2 hosts and 1 switch
  and ICMP ECHO + ECHO reply the packet has to travel 4 ethernet
  segments which is already 60μs;

  probably something a bit else is also there as e.g. on Linux, even
  with `cpupower frequency-set -g performance`, on some computers I've
  noticed the kernel can be spending more time in software-only mode
  when incoming packets go in less frequently. E.g. this program can
  demonstrate the effect for ICMP ECHO processing:

  https://lab.nexedi.com/kirr/bcc/blob/43cfc13b/tools/pinglat.py

  (later this was found to be partly due to C-states exit latencies) )

We have this patch running in our testing setup for 1 months already
without any issues observed.

It remains to be clarified whether RX and TX timers use the same base.
For now I've set them equally, but Francois's original patch version
suggests it could be not the same.

I've got no feedback at all to my original posting of this patch and questions

	https://www.spinics.net/lists/netdev/msg457173.html

neither from Francois, nor from any people from Realtek during one month.

So I suggest we simply apply it to net-next.git now.

Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Stéphane ANCELOT <sancelot@free.fr>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bridge: make setlink/dellink notifications more accurate

Before this set the bridge would generate a notification on vlan add or del
even if they didn't actually do any changes, which confuses listeners and
is generally not preferred. We could also lose notifications on actual
changes if one adds a range of vlans and there's an error in the middle.
The problem with just breaking and returning an error is that we could
break existing user-space scripts which rely on the vlan delete to clear
all existing entries in the specified range and ignore the non-existing
errors (typically used to clear the current vlan config).
So in order to make the notifications more accurate while keeping backwards
compatibility we add a boolean that tracks if anything actually changed
during the config calls.

The vlan add is more difficult to fix because it always returns 0 even if
nothing changed, but we cannot use a specific error because the drivers
can return anything and we may mask it, also we'd need to update all places
that directly return the add result, thus to signal that a vlan was created
or updated and in order not to break overlapping vlan range add we pass
down the new boolean that tracks changes to the add functions to check
if anything was actually updated.

v6: moved "changed" in else branch in br|nbp_vlan_add, thanks to
    Toshiaki Makita and retested everything again
v5: fix br_vlan_add return (v1 leftover) spotted by Toshiaki Makita
v4: set changed always to false in the non-vlan config case and retested
v3: rebased to latest net-next and fixed non-vlan config functions reported
    by kbuild test bot
v2: pass changed down to vlan add instead of masking errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this patch we had cases that either sent notifications when there
were in fact no changes (e.g. non-existent vlan delete) or didn't send
notifications when there were changes (e.g. vlan add range with an error in
the middle, port flags change + vlan update error). This patch sends down
a boolean to the functions setlink/dellink use and if there is even a
single configuration change (port flag, vlan add/del, port state) then
we always send a notification. This is all done to keep backwards
compatibility with the opportunistic vlan delete, where one could
specify a vlan range that has missing vlans inside and still everything
in that range will be cleared, this is mostly used to clear the whole
vlan config with a single call, i.e. range 1-4094.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

two extra #include are not necessary in tcp.h
Remove them.

Fixes: 40304b2a ("bpf: BPF support for sock_ops")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: move 12 sysctls to namespaces

Ideally all TCP sysctls should be per netns.
This patch series takes care of 12 sysctls.

Remains the ones that need discussion :

sysctl_tcp_mem, sysctl_tcp_rmem, sysctl_tcp_wmem, and sysctl_tcp_max_orphans
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roman Yeryomin <leroi.lists@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Denis Kirjanov <kda@linux-powerpc.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Allen Pais <allen.lkml@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>