The current renesas_usbhs driver triggers

BUG: scheduling while atomic: ksoftirqd/0/3/0x00000102

with enabled CONFIG_DEBUG_ATOMIC_SLEEP, by submitting DMA transfers from
an atomic (tasklet) context, which is not supported by the shdma dmaengine
driver. Fix it by switching to a work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

list.h already provide helpers to find the first entry and to move list
nodes to the tail of another list. This patch simply uses those helpers,
no functional changes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds SS descriptors to the ACM & generic serial gadget. The
ACM part was tested with minicom + dummy + send / receive files over
ttyACM <=> ttyGS0.
The generic serial part (f_serial) was not tested (haven't found a
driver on the host side).
The nokia & multi gadget use HS at most.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since commit 72c973dd aka ("usb: gadget: add usb_endpoint_descriptor to
struct usb_ep) the descriptor is part of the ep. Most gadgets like
g_zero or masstorage call config_ep_by_speed() to grab an available
endpoint which may be used for FS/HS/SS bulk/iso/intr and in a second
they assign the proper descriptor by calling config_ep_by_speed(). This
is good so far. A few of them like ncm call config_ep_by_speed() only if
ep->desc not assigned earlier. That means ep->desc is never assigned if
the endpoint was used by another gadget before it was removed.

Some of those gadgets also assign ep->driver_data to NULL on reset or
ep_disable part _but_ keep a reference to this endpoint. At ep_enable
time they assign driver_data to their private data. This probably needs
a clean up of its own.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Problem:
 pch_udc continues operation even if VBUS becomes Low.
 pch_udc performs D+ pulling up before VBUS becomes High.
 USB device should be controlled according to VBUS state.

Root cause:
 The current pch_udc is not always monitoring VBUS.

Solution:
 The change of VBUS is detected using an interrupt of GPIO.
 If VBUS became Low, pch_udc handles 'disconnect'.
 After VBUS became High, a pull improves D+, and pch_udc
 handles 'connect'.

[ balbi@ti.com : make it actually compile ]
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Problem:
 In USB Suspend, pch_udc handles 'disconnect'.

Root cause:
 The current pch_udc is not monitoring VBUS.
 When USB cable is disconnected, USB Device Controller generates
 an interrupt of USB Suspend.
 pch_udc cannot distinguish it is USB Suspend or disconnect.
 Therefore, pch_udc handles 'disconnect' after an interrupt of
 USB Suspend happend.

Solution:
 VBUS is detected through GPIO.
 After an interrupt produced USB Suspend, if VBUS is Low,
 pch_udc handles 'disconnect'.
 If VBUS is High, pch_udc handles 'suspend'.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

_ep to ep is a pointer substraction so ep won't be zero unless _ep was
8. This was not intendent by the author, it was probably a typo while
checking for NULL of the argument.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If the stream check fails then we leave ep->desc assigend but we return
with an error code. The caller assumes the endpoint is not enabled
(which is the case) but it can not enable it again due to this
assigment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add IAD to bind the two interfaces of ECM so that it works properly
in composite gadget mode.
Signed-off-by: Thirupathi <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove one define of FSG_NO_INTR_EP and we still have that we can use.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The m.nazarewicz@samsung.com email address is no longer valid,
so this commit replaces it with mina86@mina86.com which is
employer-agnostic and thus should be valid for foreseeable
feature.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch converts checkpatch output of
|./scripts/checkpatch.pl drivers/usb/gadget/dummy_hcd.c -file

from
|total: 22 errors, 174 warnings, 2642 lines checked

to
|total: 0 errors, 0 warnings, 2632 lines checked
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch makes use of usb_endpoint_type() instead of the open coding.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

dummy_hcd provides (alloc|free)_stream() callbacks but there are not
doing anything. The transfer side also lacks matching of streams. This
patch changes this and implements stream allocation / de-allocation
support and proper urb <=> req matching.
The UDC side exposes a limit of 16 streams. DWC3, the only USB3 UDC has
no limitations in this regard except that it _needs_ to know that
streams will be used at the ep_enable time. At the host side, there is
no real limit either: XHCI can allocate any number of streams as long as
it does not run out of memory. The UAS gadget currently requests 16
streams and the UAS host side fallbacks from the requested 256 down to
16 which is fine.
From the UASP point of view (the only specified user), the number of
used streams does not really matter. The only limitation is that the
host may not use a higher stream than the gadget requested and can deal
with.

The dummy stream support has been modelled after current UAS + XHCI +
DWC3 + UASP usage which helps me testing:
- the device announces that each ep supports 16 streams (even it could
  more than that).
- the device side looks into Companion descriptor at ep_enable time and
  enables them according to it.
- the host side tries to enable the requested number of streams but the
  upper limit is the Comanion descriptor. None (zero streams) is an
  error condition, less is okay.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
Adding debugging messages.

CAUSE:
The debugging messages are added to make sure of that major interrupt events
are occurring.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
USB Suspend interrupts occur frequently.

CAUSE:
When it is called pch_udc_reconnect() in USB Suspend, it repeats reset and
Suspend.

SOLUTION:
pch_udc_reconnect() does not enable all interrupts.  When an enumeration event
occurred the driver enables all interrupts.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
After a USB cable is connect/disconnected, the system rarely freezes.

CAUSE:
Since the USB device controller cannot know to disconnect the USB cable, when
it is used without detecting VBUS by GPIO, the UDC driver does not notify to
USB Gadget.

Since USB Gadget cannot know to disconnect, a false setting occurred when the
USB cable is connected/disconnect repeatedly.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
After USB Suspend, a system rarely freezes.

CAUSE:
When USB Suspend occurred, the driver is not notifying
a gadget of the event.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
If the return value of pch_udc_pcd_init() is False, the return value of
this function is unsettled.
Since pch_udc_pcd_init() always returns 0, there is not actually the issue.

CAUSE:
If pch_udc_pcd_init() is True, the variable, retval, is not set for an
appropriate value.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

ISSUE:
When the driver notifies a gadget of a disconnect event, a system
rarely freezes.

CAUSE:
When the driver calls dev->driver->disconnect(), it is not calling
spin_unlock().
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This will enable the system to check for activity of the usb gadget
and also in a later patch to control the usbphy power-domain.
When handling the power domain there, it will be possible to remove
another reference to architecture code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The helper functions were definied but never used until now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The SUDMAC uses 8-bit width only. So, when the driver uses SUDMAC,
we have to clear the MBW_32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In case of the SH7757, the irq number of USB module and SUDMAC
are the same. So, we have to set the IRQF_SHARED in such a case.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We've dereferenced req already, and we checked for bogus parameters at
the start of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is no reason why dummy_alloc_streams() and dummy_free_streams()
are global. Make them static instead.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This renames a function so "update" is spelled properly.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds sg support to dummy_hcd. It seems that uas is not able
to work with a hcd which does not support sg only based transfers.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves the part of the code which does the bare transfer into
its function. It is a preparion for the implementation of sg support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

While playing with uasp I noticed that it does not work with dummy_hcd.
The problem is that uasp requires a stream capable endpoint which it is
requesting at bind time like every other gadget. dummy_hcd however
initializes the max_stream value after connect once it knows if it runs
at SS or not.
I don't think that it is might be wrong to initialize the stream
capability even at HS speed. The gadget may not use this descriptor at
HS speed so it should not cause any damage.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge branches 'sched-urgent-for-linus', 'perf-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/accounting, proc: Fix /proc/stat interrupts sum

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracepoints/module: Fix disabling tracepoints with taint CRAP or OOT
  x86/kprobes: Add arch/x86/tools/insn_sanity to .gitignore
  x86/kprobes: Fix typo transferred from Intel manual

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
  x86, tsc: Fix SMI induced variation in quick_pit_calibrate()
  x86, opcode: ANDN and Group 17 in x86-opcode-map.txt
  x86/kconfig: Move the ZONE_DMA entry under a menu
  x86/UV2: Add accounting for BAU strong nacks
  x86/UV2: Ack BAU interrupt earlier
  x86/UV2: Remove stale no-resources test for UV2 BAU
  x86/UV2: Work around BAU bug
  x86/UV2: Fix BAU destination timeout initialization
  x86/UV2: Fix new UV2 hardware by using native UV2 broadcast mode
  x86: Get rid of dubious one-bit signed bitfield

gpio bug fixes for v3.3

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio: tps65910: Use correct offset for gpio initialization
  gpio/it8761e: Restrict it8761e gpio driver to x86.
  gpio-ml-ioh: cleanup __iomem annotation usage
  gpio-ml-ioh: cleanup NULL pointer checking
  gpio-pch: cleanup __iomem annotation usage
  gpio-pch: cleanup NULL pointer checking

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qnx4: don't leak ->BitMap on late failure exits
  qnx4: reduce the insane nesting in qnx4_checkroot()
  qnx4: di_fname is an array, for crying out loud...
  vfs: remove printk from set_nlink()
  wake up s_wait_unfrozen when ->freeze_fs fails

In checkin

  303395ac x86: Generate system call tables and unistd_*.h from tables

the feature macros in <asm/unistd.h> were unified between 32 and 64
bits.  Unfortunately 32 bits requires __ARCH_WANT_SYS_IPC and this was
inadvertently dropped.
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/CALLzPKbeXN5gdngo8uYYU8mAow=XhrwBFBhKfG811f37BubQOg@mail.gmail.com

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Permit key_serial() to be called with a const key pointer
  keys: fix user_defined key sparse messages
  ima: fix cred sparse warning
  MPILIB: Add a missing ENOMEM check

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

(struct qnx4_inode_entry *)(bh->b_data + some_offset)->di_fname
is not going to be NULL, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>