Patch from Ben Dooks

Add some basic documentation about the support for
the S3C2412 and S3C2413 CPUs--
Signed-off-by: Ben Dooks &lt;ben-linux@fluff.org&gt;Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

This patch adds support for the Ajeco 1ARM Single Board Computer, a
VME form factor SBC based on the Atmel AT91 SoC, with 64M RAM, seven
serial ports, three ethernet ports, IDE, CF, USB host and device,
and S-Video/VGA out.--
Signed-off-by: Lennert Buytenhek &lt;buytenh@wantstofly.org&gt;Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

While reviewing the IRQ autoprobing code i found the attached buglet.
probe_irq_on()/off() calls must always be in pairs, because the generic IRQ
code uses a global semaphore to serialize all autoprobing activites.
(which does make sense) The ARM code's probe_irq_*() implementation does
not do this, but if this driver is ever used on another platform, this bug
might bite.

(It probably does not trigger in practice, because a zero probing mask
returned should be rare - but still.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add the rest of the supported S3C24XX family to the
configuration selection for ARCH_S3C2410. This should
try and make it clearer for people trying to find the
S3C2440 or freinds where they can be found.--
Signed-off-by: Ben Dooks &lt;ben-linux@fluff.org&gt;Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add SMDK2413 to the list of the machines being
built for ARCH_S3C2410, thus ensursing our all
machines build has an representitive of the
S3C2412/S3C2413 CPU series--
Signed-off-by: Ben Dooks &lt;ben-linux@fluff.org&gt;Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Make CPU uppercase on the SMDK2440 KConfig entries--
Signed-off-by: Ben Dooks &lt;ben-linux@fluff.org&gt;Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Milan Svoboda

IXP4XX platform can happily live without pci bus. This patch modifies
Kconfig to support this option and modifies Makefile so pci only files
are compiled only when pci is really selected.

Patch is tested and ixdp465 runs fine with or without the pci bus.--
Signed-off-by: Milan Svoboda &lt;msvoboda@ra.rockwell.com&gt;Signed-off-by: Deepak Saxena &lt;dsaxena@plexity.net&gt;Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

DEFAULT_FIQ was entirely unused.  MODE_* are just redefinitions
of *_MODE.  Use *_MODE instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As for RETINSTR/LOADREGS macros, these were for compatibility
with 26-bit ARMs.  No longer required, so remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

proc-v6 contains some compatibility to be able to use the V6
"cps" instruction.  However, the kernel makes use of this
instruction elsewhere extensively, so there's no point keeping
this compatibility anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As for RETINSTR, LOADREGS is a left-over from the 26-bit days.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

RETINSTR is a left-over from the days when we had 26-bit and
32-bit CPU support integrated into the same tree.  Since this
is no longer the case, we can now remove RETINSTR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
  [ARM] 3648/1: Update struct ucontext layout for coprocessor registers
  [ARM] Add identifying number for non-rt sigframe
  [ARM] Gather common sigframe saving code into setup_sigframe()
  [ARM] Gather common sigframe restoration code into restore_sigframe()
  [ARM] Re-use sigframe within rt_sigframe
  [ARM] Merge sigcontext and sigmask members of sigframe
  [ARM] Replace extramask with a full copy of the sigmask
  [ARM] Remove rt_sigframe puc and pinfo pointers
  [ARM] 3647/1: S3C24XX: add Osiris to the list of simtec pm machines
  [ARM] 3645/1: S3C2412: irq support for external interrupts
  [ARM] 3643/1: S3C2410: Add new usb clocks
  [ARM] 3642/1: S3C24XX: Add machine SMDK2413
  [ARM] 3641/1: S3C2412: Fixup gpio register naming
  [ARM] 3640/1: S3C2412: Use S3C24XX_DCLKCON instead of S3C2410_DCLKCON
  [ARM] 3639/1: S3C2412: serial port support
  [ARM] 3638/1: S3C2412: core clocks
  [ARM] 3637/1: S3C24XX: Add mpll clock, and set as fclk parent
  [ARM] 3636/1: S3C2412: Add selection of CPU_ARM926
  [ARM] 3635/1: S3C24XX: Add S3C2412 core cpu support
  [ARM] 3633/1: S3C24XX: s3c2410 gpio bugfix - wrong pin nos
  ...

This reverts commit 786dc1d3.

As Al so eloquently points out, the patch is crap. The old code was fine,
the new code was bogus.

It never dereferenced a user pointer, the "->" operator was to an array
member, which gives the _address_ of the member (in user space), not an
actual dereference at all.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from Daniel Jacobowitz

In order for userspace to find saved coprocessor registers, move them from
struct rt_sigframe into struct ucontext.  Also allow space for glibc's
sigset_t, so that userspace and kernelspace can use the same ucontext
layout.  Define the magic numbers for iWMMXt in the header file for easier
reference.  Include the size of the coprocessor data in the magic numbers.

Also define magic numbers and layout for VFP, not yet saved.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: radeon constify radeon microcode
  Add i915 ioctls to configure pipes for vblank interrupt.
  drm: update radeon to 1.25 add r200 vertex program support
  drm: radeon add a tcl state flush before accessing tcl vector space

* 'intelfb-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6:
  intelfb delousing

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (40 commits)
  [SPARC64]: Update defconfig.
  [SPARC64]: Make auxio a real driver.
  [PARPORT] sunbpp: Convert to new SBUS device framework.
  [Documentation]: Update probing info in sbus_drivers.txt
  [SCSI] qlogicpti: Convert to new SBUS device framework.
  [SCSI] esp: Fix bug in esp_remove_common.
  [NET] sunhme: Kill useless loop over sdevs in quattro_sbus_find().
  [NET] myri_sbus: Kill unused next_module struct member.
  [NET] myri_sbus: Convert to new SBUS device layer.
  [NET] sunqe: Convert to new SBUS driver layer.
  [NET] sunbmac: Convert over to new SBUS device framework.
  [NET] sunlance: Convert to new SBUS driver framework.
  [NET] sunhme: Convert to new SBUS driver framework.
  [NET] sunhme: Kill __sparc__ and __sparc_v9__ ifdefs.
  [SCSI] sparc: Port esp to new SBUS driver layer.
  [SOUND] sparc: Port amd7930 to new SBUS device layer.
  [SBUS]: Rewrite and plug into of_device framework.
  [SPARC]: Port of_device layer and make ebus use it.
  [SPARC]: Port sparc64 in-kernel device tree code to sparc32.
  [SPARC64]: Add of_device layer and make ebus/isa use it.
  ...

This is the minimal resume trace code to find which device resume (if
any) results in problems.  Usually, you'd use the information this
generates as a starting point to adding more fine-grained trace event
points.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Considering that there isn't a lot of hw we can depend on during resume,
this is about as good as it gets.

This is x86-only for now, although the basic concept (and most of the
code) will certainly work on almost any platform.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

GDB couldn't reliably tell the difference between the old and new
non-rt sigframes, so provide it with a number at the beginning which
will never appear in the old sigframe, and hence provide gdb with a
reliable way to tell the two apart.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Enable power management for Simtec Osiris
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Move the decoding of the IRQ_EXT4 and above out of
the entry macro, and into an chained irq handler
as the EXTINT registers move depending on the CPU
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Make the S3C2410 use the same usb clock naming
as the S3C2412
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add basic support for the Samsung/Aiji SMDK2413
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The current S3C2412 has used to moving S3C24XX_
for the generic form of an register has been
moved from the S3C2410.

Fixup S3C2410_EXTINTx and S3C2410_EINFLTx to
S3C24XX_EXTINTx and S3C24XX_EXTINTx

Depends on Patch #3635/1, Patch #3640/1
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The current S3C2412 support has moved to using
S3C24XX_DCLKCON unless the specific DCLKCON is
required (S3C2412_DCLKCON or S3C2410_DKCLKCON)

Move the few places using S3C2410_DCLKCON to
S3C24XX_DCLKCON

Depends on Patch #3635/1
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Clock support for the clocks on the Samsung S3C2412
and S3C2413 SoCs. This provides clock enables and
parent selection for all the standard clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Update the clocks with the MPLL clock, and
use it as the parent. Also export these to
the rest of arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Select CONFIG_CPU_ARM926 when CONFIG_CPU_S3C2412 is
selected.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add support for the Samsung S3C2412 and S3C2413 range
of SoCs. This patch contains the core identification,
debug macros, and basic register updates to get these
to build.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The s3c2410 gpio functions have a pair of bugs where
the code is using the pin function definitions instead
of the pin gpio numbers.

Also remove the changelog
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

Remove the remaining legacy __mem_isa() definitions for the ARM
platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

The ep93xx ohci bits have been merged into the gregkh-2.6 tree, which
means that they will probably go upstream soon, so make the core ep93xx
code instantiate an appropriate ep93xx-ohci platform device.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add an initial implementation of the clk_* API for the cirrus ep93xx
to the tree.  The initial implementation is somewhat minimal, with the
intention of extending it as we go along.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>