DSI supports interleaving of command mode packets during the HSA, HFP, HBP and
BLLP blanking intervals in a video mode stream. This is useful as a user may
want to read or change the configuration of a panel without stopping the video
stream.

On OMAP DSI, we can queue HS or LP command mode packets in the TX FIFO, and
the DSI HW takes care of interleaving this data during the one of the blanking
intervals. The DSI HW needs to be programmed with the maximum amount of data
that can be interleaved in a particular blanking period. A blanking period
cannot be used to send command mode data for it's complete duration, there is
some amount of time required for the DSI data and clock lanes to transition
to the desired LP or HS state.

Based on the state of the lanes at the beginning and end of the blanking period,
we have different scenarios, with each scenario having a different value of time
required to transition to HS or LP. Refer to the section 'Interleaving Mode' in
OMAP TRM for more info on the scenarios and the equations to calculate the time
required for HS or LP transitions.

We use the scenarios which takes the maximum time for HS or LP transition, this
gives us the minimum amount of time that can be used to interleave command mode
data. The amount of data that can be sent during this minimum time is calculated
for command mode packets both in LP and HS. These are written to the registers
DSI_VM_TIMING4 to DSI_VM_TIMING6.

The calculations don't take into account the time required of transmitting BTA
when doing a DSI read, or verifying if a DSI write went through correctly. Until
these latencies aren't considered, the behaviour of DSI is unpredictable when
a BTA is interleaved during a blanking period. Enhancement of these calculations
is a TODO item.

The calculations are derived from DSI parameter calculation tools written by
Sebastien Fagard <s-fagard@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DISPC has two accumulator registers DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 each
with horizontal and vertical bit fields. The bit fields can take values in the
range of -1024 to 1023. Based on bit field values DISPC decides on which one out
of 8 phases the filtering starts. DISPC_VIDp_ACCU_0 is used for progressive
output and for interlaced output both DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1
are used.

The current accumulator values in DISPC scaling logic for chroma plane takes
default values for all color modes and rotation types. So, the horizontal and
vertical up and downsampling accumulator bit field values have been updated for
better performance.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge OMAP DSS HDMI audio patches from Ricardo Neri

Implement the DSS device driver audio support interface in the HDMI
panel driver and generic driver. The implementation relies on the
IP-specific functions that are defined at DSS probe time.

A mixed locking strategy is used. The panel's mutex is used when
the state of the panel is queried as required by the audio functions.
The audio state is protected using a spinlock as users of DSS HDMI
audio functionality might start/stop audio while holding a spinlock.
The mutex and the spinlock are held and released as needed by each
individual function to protect the panel state and the audio state.

Although the panel's audio_start functions does not check whether
the panel is active, the audio _ENABLED state can be reached only
from audio_enable, which does check the state of the panel. Also,
if the panel is ever disabled, the audio state will transition
to _DISABLED. Transitions are always protected by the audio lock.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

As the hdmi_lock mutex is inside the hdmi struct, rename to simply
"lock". This is only a change in the name. There are not changes
in functionality.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

As of today, the only know user of the DSS HDMI audio support is
ASoC. Hence, it makes sense to remap the speaker order to match
the ALSA speaker order. In the future, a dynamic mapping mechanism
may be implemented.

Remapping is needed as the HDMI speaker order is FL/FR/LFE/C/RL/RR/
RLC-FLC/RRC-FLC while the ALSA order is FL/FR/RL/RR/C/LFE/SL/SR.
Refer to CEA-861 Section 6.6.2 for further details.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

The generic HDMI driver does not need to know about the specific
settings of a given IP. Hence, it just passes the audio configuration
and the IP library parses such configuration and sets the IP
accordingly. This patch introduces an IP-specific audio configuration
function.

Also, this patch implements the audio config function for OMAP4. The
DMA, format and core config functions are no longer exposed to the
generic HDMI driver as they are IP-specific.

The audio configuration function caters for 16-bit through 24-bit
audio samples with sample rates from 32kHz and up to 192kHz as well
as up to 8 audio channels.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Add support for more sample rates when calculating N and CTS. This
covers all the audio sample rates that an HDMI source is allowed
to transmit according to the HDMI 1.4a specification.

Also, reorganize the logic for the calculation when using deep color.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

The N and CTS parameters are relevant to all HDMI implementations and
not specific to a given IP. Hence, the calculation is relocated
into the generic HDMI driver.

Also, deep color is not queried but it is still considered in the
calculation of N. This is to be changed when deep color functionality is
implemented in the driver.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Utilize a snd_aes_iec958 struct to write the parameters of the IEC-60958
channel status word into the HDMI IP registers. Hence, the user of the
driver has full control of what parameters are written in the word.

Also, some of the parameters of the I2S structure have been removed
as they are actually IEC-60958 parameters.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Instead of having OMAPDSS HDMI audio functionality depending on the
ASoC HDMI audio driver, use a new config option so that
potential users, including ASoC, may select if needed.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Decouple the enable/disable operation of the HDMI audio wrapper from
audio start/stop. Otherwise, an audio FIFO underflow may occur. The
audio wrapper enablement must be done after configuration and
before audio playback is started.
Signed-off-by: Axel Castaneda Gonzalez <x0055901@ti.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

According to the most up-to-date documentation from Texas Instruments,
the configuration of High Bitrate Audio is not possible. Also, it is
not possible to set polarity of the I2S Word Select signal. This patch
removes the invalid settings.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Instead of having its own definitions for CEA-861 and IEC-60958, the HDMI
driver should use those provided by ALSA. This patch removes the definitions
that are already provided by ALSA.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Remove the ASoC OMAP HDMI audio codec. The goal of removing the codec
is to, in subsequent patches, give way to the implementation of the HDMI
audio support using the DSS device driver audio interface. This
approach will expose the HDMI audio functionality to any interested entity.

In a separate patch, ASoC will use this new approach to expose HDMI audio
to ALSA.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

To improve readability, split the video_enable HDMI IP operation
into two separate functions for enabling and disabling video.
The video_enable function is also modified to return an error value.

While there, update these operations for the OMAP4 IP accordingly.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

To improve readability, split the audio_enable HDMI IP operation
into two separate functions for enabling and disabling audio.
The audio_enable function is also modified to return an error value.

While there, update these operations for the OMAP4 IP accordingly.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

There exist several display technologies and standards that support audio as
well. Hence, it is relevant to update the DSS device driver to provide an audio
interface that may be used by an audio driver or any other driver interested in
the functionality.

The audio_enable function is intended to prepare the relevant
IP for playback (e.g., enabling an audio FIFO, taking in/out of reset
some IP, enabling companion chips, etc). It is intended to be called before
audio_start. The audio_disable function performs the reverse operation and is
intended to be called after audio_stop.

While a given DSS device driver may support audio, it is possible that for
certain configurations audio is not supported (e.g., an HDMI display using a
VESA video timing). The audio_supported function is intended to query whether
the current configuration of the display supports audio.

The audio_config function is intended to configure all the relevant audio
parameters of the display. In order to make the function independent of any
specific DSS device driver, a struct omap_dss_audio is defined. Its purpose
is to contain all the required parameters for audio configuration. At the
moment, such structure contains pointers to IEC-60958 channel status word and
CEA-861 audio infoframe structures. This should be enough to support HDMI and
DisplayPort, as both are based on CEA-861 and IEC-60958. The omap_dss_audio
structure may be extended in the future if required.

The audio_enable/disable, audio_config and audio_supported functions could be
implemented as functions that may sleep. Hence, they should not be called
while holding a spinlock or a readlock.

The audio_start/audio_stop function is intended to effectively start/stop audio
playback after the configuration has taken place. These functions are designed
to be used in an atomic context. Hence, audio_start should return quickly and be
called only after all the needed resources for audio playback (audio FIFOs,
DMA channels, companion chips, etc) have been enabled to begin data transfers.
audio_stop is designed to only stop the audio transfers. The resources used
for playback are released using audio_disable.

A new enum omap_dss_audio_state is introduced to help the implementations of
the interface to keep track of the audio state. The initial state is _DISABLED;
then, the state transitions to _CONFIGURED, and then, when it is ready to
play audio, to _ENABLED. The state _PLAYING is used when the audio is being
rendered.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>

Merge OMAP DSS cleanups that restructure the omapdss driver to facilitate
implementing device tree support in the future.

The Beagleboard xM gpio used for TFP410 powerdown is connected through
an I2C attached chip which means setting the GPIO can sleep. Code that
calls tfp410_power_on/off holds a mutex, so sleeping should be fine.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Move the platform-data based display device initialization into a
separate function, so that we may later add of-based initialization.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We currently use the id of the dsi platform device (dsidev->id) as the
DSI hardware module ID. This works because we assign the ID manually in
arch/arm/mach-omap2/display.c at boot time.

However, with device tree the platform device IDs are automatically
assigned to an arbitrary number, and we can't use it.

Instead of using dsidev->id during operation, this patch stores the
value of dsidev->id to a private field of the dsi driver at probe(). The
future device tree code can thus set the private field with some other
way.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Now that each output driver creates their own display devices, the
output drivers can also initialize those devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.

With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.

To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We currently have a two ways to set a "default panel device" for dss, to
which the overlays are connected when the omapdss driver is loaded:

- in textual format (name of the display) as cmdline parameter
- as a pointer to the panel device from board file via pdata

The current code handles this in a bit too complex way by using both of
the above methods during runtime. However, with DT we don't have pdata
anymore, so the code handling the second case won't work anymore. The
current code has also the problem that it modifies the platform_data.

This patch simplifies the code a bit by using the pointer method only
inside the probe function, and stores the name of the panel device. This
way we only need to handle the textual format during operation and also
avoid modifying the platform_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Change omapfb to use platform_driver_probe and add __init & __exit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Now that we are using platform_driver_probe() we can add __inits and
__exits all around.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Now that the core.c doesn't fail if output driver's init fails, we can
change the uses of platform_driver_register to platform_driver_probe.
This will allow us to use __init in the following patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Instead of having an ugly #ifdef mess in the core.c for creating debugfs
files, add a dss_debugfs_create_file() function that the dss drivers
can use to create the debugfs files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Initialize and uninitialize the output drivers by using arrays of
pointers to the init/uninit functions. This simplifies the code
slightly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Now that the omapdss_core device is the parent for all other dss
devices, we don't need to use the dss_runtime_get/put anymore. Instead,
enabling omapdss_core will happen automatically when a child device is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.

This patch modifies the dpi.c and sdi.c to create drivers for the
platform devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.

This patch modifies arch/arm/mach-omap2/display.c to create platform
devices for DPI and SDI, and later patches will implement driver for
them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Instead of using omap_device_build() to create the omap_devices for DSS
hwmods, create them with a custom function. This will allow us to create
a parent-child hierarchy for the devices so that the omapdss_core device
is parent for the rest of the dss hwmod devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The platform devices for omapdss, dss and dispc drivers are always
present, so we can use platform_driver_probe instead of
platform_driver_register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

For unknown reasons we seem to have a return in each of the omapdss's
uninit functions, which is a void function.

Remove the returns.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The DSI driver uses dsi_get_dsidev_id() to get the ID number for the DSI
instance. However, there were a few places where dsidev->id was used
instead of the function. Fix those places to use the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

To ease device tree adaptation in the future, rewrite TFP410 platform
data handling to be done inside probe(), so that probe() is the only
place where we need to handle the DT/pdata choice.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omapfb_parse_vram_param()'s check for end pointer returned from
simple_strtoul() is wrong, causing the code to bug if the second or
later vram parameters are non-parseable, for example
"omapfb.vram=0:2M,:5M".

However, even in that case the code will most likely bail out with
-EINVAL in the following checks, so the bug is probably not a fatal one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>