- 06 Oct, 2015 3 commits
-
-
Taku Izumi authored
In multi-segment system, uncore devices may belong to buses whose segment number is other than 0: .... 0000:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03) ... 0001:7f:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03) ... 0001:bf:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03) ... 0001:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03 ... In that case, relation of bus number and physical id may be broken because "uncore_pcibus_to_physid" doesn't take account of PCI segment. For example, bus 0000:ff and 0001:ff uses the same entry of "uncore_pcibus_to_physid" array. This patch fixes this problem by introducing the segment-aware pci2phy_map instead. Signed-off-by:
Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: acme@kernel.org Cc: hpa@zytor.com Link: http://lkml.kernel.org/r/1443096621-4119-1-git-send-email-izumi.taku@jp.fujitsu.comSigned-off-by:
Ingo Molnar <mingo@kernel.org>
-
Kan Liang authored
This patch adds new PMUs to support cstate related free running (read-only) counters. These counters may be used simultaneously by other tools, such as turbostat. However, it still make sense to implement them in perf. Because we can conveniently collect them together with other events, and allow to use them from tools without special MSR access code. These counters include CORE_C*_RESIDENCY and PKG_C*_RESIDENCY. According to counters' scope and category, two PMUs are registered with the perf_event core subsystem. - 'cstate_core': The counter is available for each physical core. The counters include CORE_C*_RESIDENCY. - 'cstate_pkg': The counter is available for each physical package. The counters include PKG_C*_RESIDENCY. The events are exposed in sysfs for use by perf stat and other tools. The files are: /sys/devices/cstate_core/events/c*-residency /sys/devices/cstate_pkg/events/c*-residency These events only support system-wide mode counting. The /sys/devices/cstate_*/cpumask file can be used by tools to figure out which CPUs to monitor by default. The PMU type (attr->type) is dynamically allocated and is available from /sys/devices/core_misc/type and /sys/device/cstate_*/type. Sampling is not supported. Here is an example. - To caculate the fraction of time when the core is running in C6 state CORE_C6_time% = CORE_C6_RESIDENCY / TSC # perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 sleep 5 11838820015,,cstate_core/c6-residency/,5175919658,100.00 11877130740,,msr/tsc/,5175922010,100.00 For sleep, 99.7% of time we ran in C6 state. # perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 busyloop 1253316,,cstate_core/c6-residency/,4360969154,100.00 10012635248,,msr/tsc/,4360972366,100.00 For busyloop, 0.01% of time we ran in C6 state. Signed-off-by:Kan Liang <kan.liang@intel.com> Signed-off-by:
-
Ingo Molnar authored
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo: User visible changes: - Switch the default callchain output mode to 'graph,0.5,caller', to make it look like the default for other tools, reducing the learning curve for people used to 'caller' based viewing. (Arnaldo Carvalho de Melo) - Implement column based horizontal scrolling in the hists browser (top, report), making it possible to use the TUI for things like 'perf mem report' where there are many more columns than can fit in a terminal. (Arnaldo Carvalho de Melo) - Support sorting by symbol_iaddr with perf.data files produced by 'perf mem record'. (Don Zickus) - Display DATA_SRC sample type bit, i.e. when running 'perf evlist -v' the "DATA_SRC" wasn't appearing when set, fix it to look like: (Jiri Olsa) cpu/mem-loads/pp: ...SNIP... sample_type: IP|TID|TIME|ADDR|CPU|PERIOD|DATA_SRC - Introduce the 'P' event modifier, meaning 'max precision level, please', i.e.: $ perf record -e cycles:P usleep 1 Is now similar to: $ perf record usleep 1 Useful, for instance, when specifying multiple events. (Jiri Olsa) - Make 'perf -v' and 'perf -h' work. (Jiri Olsa) - Fail properly when pattern matching fails to find a tracepoint, i.e. '-e non:existent' was being correctly handled, with a proper error message about that not being a valid event, but '-e non:existent*' wasn't, fix it. (Jiri Olsa) Infrastructure changes: - Separate arch specific entries in 'perf test' and add an 'Intel CQM' one to be fun on x86 only. (Matt Fleming) Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
- 05 Oct, 2015 16 commits
-
-
Jiri Olsa authored
Currently we dont fail properly when pattern matching fails to find any tracepoint. Current behaviour: $ perf record -e 'sched:krava*' sleep 1 WARNING: event parser found nothinginvalid or unsupported event: 'sched:krava*' Run 'perf list' for a list of valid events usage: perf record [<options>] [<command>] or: perf record [<options>] -- <command> [<options>] This patch change: $ perf record -e 'sched:krava*' sleep 1 event syntax error: 'sched:krava*' \___ unknown tracepoint Error: File /sys/kernel/debug/tracing/events/sched/krava* not found. Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?. Run 'perf list' for a list of valid events usage: perf record [<options>] [<command>] or: perf record [<options>] -- <command> [<options>] Reported-by:Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Tested-by:
-
Arnaldo Carvalho de Melo authored
Do it using the recently introduced ui_brower scrolling mode, setting ui_browser.columns to the number of sort columns and then, when rendering each line, skipping as many initial columns as the user pressed the right arrow. As the user presses the left arrow, the ui_browser code will remove the scrolling counter and the left scrolling takes place. The right arrow key was an alias for ENTER, so people used to press it may get a bit annoyed at first, sorry! Ditto for ESC and the left key. Callchains can be left as is or we can, when rendering the Symbol column, store the at what position on the screen it is and then using ui_browser__gotorc() to print it from there, i.e. the callchain would move around with the symbol. Leaving it as is, i.e. at a fixed position, close to the left, saves precious screen real state for it, so I'm inclined to leave it as is now. Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Chandler Carruth <chandlerc@gmail.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-ccqq9sabgfge5dwbqjwh71ij@git.kernel.orgSigned-off-by:
-
Arnaldo Carvalho de Melo authored
If the classes derived from ui_browser want to do some sort of horizontal scrolling, they have just to set ui_browser->columns to the number of columns available. Those columns can be the number of characters on the screen, if what is desired is to scroll character by character, or the number of columns in a spreadsheet like table. This is what the hist_browser will do, skipping ui_browser->horiz_scroll columns when rendering each of its lines. Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-q6a22bpmpgcr1awgzrmd4jrs@git.kernel.orgSigned-off-by:
-
Arnaldo Carvalho de Melo authored
Which is the most common default found in other similar tools. Requested-by:
-
Matt Fleming authored
Peter reports that it's possible to trigger a WARN_ON_ONCE() in the Intel CQM code by combining a hardware event and an Intel CQM (software) event into a group. Unfortunately, the perf tools are not able to create this bundle and we need to manually construct a test case. For posterity, record Peter's proof of concept test case in tools/perf so that it presents a model for how we can perform architecture specific tests, or "arch tests", in perf in the future. The particular issue triggered in the test case is that when the counter for the hardware event overflows and triggers a PMI we'll read both the hardware event and the software event counters. Unfortunately, for CQM that involves performing an IPI to read the CQM event counters on all sockets, which in NMI context triggers the WARN_ON_ONCE(). Reported-by:
Matt Fleming <matt.fleming@intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kanaka Juvva <kanaka.d.juvva@intel.com> Cc: Vikas Shivappa <vikas.shivappa@intel.com> Cc: Vince Weaver <vince@deater.net> Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.uk Link: http://lkml.kernel.org/n/tip-3p4ra0u8vzm7m289a1m799kf@git.kernel.orgSigned-off-by:
-
Matt Fleming authored
Move out the x86-specific tests into tools/perf/arch/x86/tests and define an 'arch_tests' array, which is the list of tests that only apply to the build architecture. We can also now begin to get rid of some of the #ifdef code that is present in the generic perf tests. Signed-off-by:
-
Matt Fleming authored
Tests that only make sense for some architectures currently live in the same place as the generic tests. Move out the x86-specific tests into tools/perf/arch/x86/tests and define an 'arch_tests' array, which is the list of tests that only apply to the build architecture. The main idea is to encourage developers to add arch tests to build out perf's test coverage, without dumping everything in tools/perf/tests. Signed-off-by:
-
Jiri Olsa authored
Adding handling for '-h' and '-v' options to invoke help and version command respectively. Current behaviour is: $ perf -v Unknown option: -v Usage: perf [--version] [--help] [OPTIONS] COMMAND [ARGS] $ perf -h Unknown option: -h Usage: perf [--version] [--help] [OPTIONS] COMMAND [ARGS] New behaviour: $ perf -h usage: perf [--version] [--help] [OPTIONS] COMMAND [ARGS] The most commonly used perf commands are: annotate Read perf.data (created by perf record) and display annotated code archive Create archive with object files with build-ids found in perf.data file bench General framework for benchmark suites ... $ perf -v perf version 4.3.rc3.gc99e32 Updated man page. Requested-by: -
Jiri Olsa authored
We need to properly initialize column width for symbol_iaddr field, so all symbols could fit in the column. Signed-off-by:
-
Don Zickus authored
Sorting on 'symbol' gives to broad a resolution as it can cover a range of IP address. Use the iaddr instead to get proper sorting on IP addresses. Need to use the 'mem_sort' feature of perf record. New sort option is: symbol_iaddr, header label is 'Code Symbol'. $ perf mem report --stdio -F +symbol_iaddr # Overhead Samples Code Symbol Local Weight # ........ ............ ........................ ............ # 54.08% 1 [k] nmi_handle 192 4.51% 1 [k] finish_task_switch 16 3.66% 1 [.] malloc 13 3.10% 1 [.] __strcoll_l 11 Signed-off-by:Don Zickus <dzickus@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1444068369-20978-8-git-send-email-jolsa@kernel.orgSigned-off-by:
-
Jiri Olsa authored
We cant test 'P' modifier gets properly parsed, the functionality test itself is beyond this suite. Signed-off-by:
-
Jiri Olsa authored
The 'P' will cause the event to get maximum possible detected precise level. Following record: $ perf record -e cycles:P ... will detect maximum precise level for 'cycles' event and use it. Commiter note: Testing it: $ perf record -e cycles:P usleep 1 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.013 MB perf.data (9 samples) ] $ perf evlist cycles:P $ perf evlist -v cycles:P: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|PERIOD, disabled: 1, inherit: 1, mmap: 1, comm: 1, freq: 1, enable_on_exec: 1, task: 1, precise_ip: 2, sample_id_all: 1, mmap2: 1, comm_exec: 1 $ Signed-off-by: -
Jiri Olsa authored
It'll be used in following patch. Signed-off-by:
-
Jiri Olsa authored
The annotated_source::sizeof_sym_hist could easily overflow int size, resulting in crash in __symbol__inc_addr_samples. Changing its type int size_t as was probably intended from beginning based on the initialization code in symbol__alloc_hist. Signed-off-by:
-
Jiri Olsa authored
Adding DATA_SRC bit_name call to display sample_type properly. $ perf evlist -v cpu/mem-loads/pp: ...SNIP... sample_type: IP|TID|TIME|ADDR|CPU|PERIOD|DATA_SRC, ... Signed-off-by:
-
Jiri Olsa authored
Because there's no point, PATH_MAX is big enough. Signed-off-by:
-
- 03 Oct, 2015 1 commit
-
-
Ingo Molnar authored
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo: User visible changes: - Do event name substring search as last resort in 'perf list'. (Arnaldo Carvalho de Melo) E.g.: # perf list clock List of pre-defined events (to be used in -e): cpu-clock [Software event] task-clock [Software event] uncore_cbox_0/clockticks/ [Kernel PMU event] uncore_cbox_1/clockticks/ [Kernel PMU event] kvm:kvm_pvclock_update [Tracepoint event] kvm:kvm_update_master_clock [Tracepoint event] power:clock_disable [Tracepoint event] power:clock_enable [Tracepoint event] power:clock_set_rate [Tracepoint event] syscalls:sys_enter_clock_adjtime [Tracepoint event] syscalls:sys_enter_clock_getres [Tracepoint event] syscalls:sys_enter_clock_gettime [Tracepoint event] syscalls:sys_enter_clock_nanosleep [Tracepoint event] syscalls:sys_enter_clock_settime [Tracepoint event] syscalls:sys_exit_clock_adjtime [Tracepoint event] syscalls:sys_exit_clock_getres [Tracepoint event] syscalls:sys_exit_clock_gettime [Tracepoint event] syscalls:sys_exit_clock_nanosleep [Tracepoint event] syscalls:sys_exit_clock_settime [Tracepoint event] - Reduce min 'perf stat --interval-print/-I' to 10ms. (Kan Liang) perf stat --interval in action: # perf stat -e cycles -I 50 -a usleep $((200 * 1000)) print interval < 100ms. The overhead percentage could be high in some cases. Please proceed with caution. # time counts unit events 0.050233636 48,240,396 cycles 0.100557098 35,492,594 cycles 0.150804687 39,295,112 cycles 0.201032269 33,101,961 cycles 0.201980732 786,379 cycles # - Allow for max_stack greater than PERF_MAX_STACK_DEPTH, as when synthesizing callchains from Intel PT data. (Adrian Hunter) - Allow probing on kmodules without DWARF. (Masami Hiramatsu) - Fix a segfault when processing a perf.data file with callchains using "perf report --call-graph none". (Namhyung Kim) - Fix unresolved COMMs in 'perf top' when -s comm is used. (Namhyung Kim) - Register idle thread in 'perf top'. (Namhyung Kim) - Change 'record.samples' type to unsigned long long, fixing output of number of samples in 32-bit architectures. (Yang Shi) Signed-off-by:
-
- 02 Oct, 2015 4 commits
-
-
Kan Liang authored
The --interval-print parameter was limited to 100ms. However, for example, 10ms is required to do sophisticated bandwidth analysis using uncore events. The test shows that the overhead of the system-wide uncore monitoring with 10ms interval is only ~2%. So this patch reduces the minimal interval-print allowd to 10ms. But 10ms may not work well for all cases. For example, when the cpus/threads number is very large, for system-wide core event monitoring the overhead could be high. To handle this issue, a warning will be displayed when the interval-print is set between 10ms to 100ms. So users can make a decision according to their specific cases. # perf stat -e uncore_imc_1/cas_count_read/ -a --interval-print 10 -- sleep 1 print interval < 100ms. The overhead percentage could be high in some cases. Please proceed with caution. # time counts unit events 0.010200451 0.10 MiB uncore_imc_1/cas_count_read/ 0.020475117 0.02 MiB uncore_imc_1/cas_count_read/ 0.030692800 0.01 MiB uncore_imc_1/cas_count_read/ 0.040948161 0.02 MiB uncore_imc_1/cas_count_read/ 0.051159564 0.00 MiB uncore_imc_1/cas_count_read/ Signed-off-by: -
Yang Shi authored
When run "perf record -e", the number of samples showed up is wrong on some 32 bit systems, i.e. powerpc and arm. For example, run the below commands on 32 bit powerpc: perf probe -x /lib/libc.so.6 malloc perf record -e probe_libc:malloc -a ls perf.data [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.036 MB perf.data (13829241621624967218 samples) ] Actually, "perf script" just shows 21 samples. The number of samples is also absurd since samples is long type, but it is printed as PRIu64. Build test ran on x86-64, x86, aarch64, arm, mips, ppc and ppc64. Signed-off-by:
Yang Shi <yang.shi@linaro.org> Cc: linaro-kernel@lists.linaro.org Link: http://lkml.kernel.org/r/1443563383-4064-1-git-send-email-yang.shi@linaro.org [ Bumped the 'hits' var used together with record.samples to 'unsigned long long' too ] Signed-off-by:
-
Masami Hiramatsu authored
Allow probing on kernel modules when 'perf' is built without debuginfo support. Currently perf-probe --module requires linking with libdw, but this doesn't make sense. E.g. ---- # make NO_DWARF=1 # ./perf probe -m pcspkr pcspkr_event%return Error: unknown switch `m' ---- With this patch ---- # ./perf probe -m pcspkr pcspkr_event%return Added new event: probe:pcspkr_event (on pcspkr_event%return in pcspkr) You can now use it in all perf tools, such as: perf record -e probe:pcspkr_event -aR sleep 1 ---- Signed-off-by:Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/20151002125832.18617.78721.stgit@localhost.localdomainSigned-off-by:
-
Arnaldo Carvalho de Melo authored
Some PMUs, like the 'intel_bts' one can be used as an event name, i.e.: $ perf record -e intel_bts:// usleep 1 Is a valid event name. But the code printing such PMUs was not honouring the 'event_glob' parameter, so the following line was always appearing: $ intel_bts// [Kernel PMU event] Fix it: $ [acme@felicio linux]$ perf list data List of pre-defined events (to be used in -e): uncore_imc/data_reads/ [Kernel PMU event] uncore_imc/data_writes/ [Kernel PMU event] $ Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-ajb71858n7q7ao77b8pyy74w@git.kernel.orgSigned-off-by:
-
- 01 Oct, 2015 8 commits
-
-
Arnaldo Carvalho de Melo authored
Before: # perf list _alloc_ | head -10 # After: # perf list _alloc_ | head -10 ext4:ext4_alloc_da_blocks [Tracepoint event] ext4:ext4_get_implied_cluster_alloc_exit [Tracepoint event] kmem:kmem_cache_alloc_node [Tracepoint event] kmem:mm_page_alloc_extfrag [Tracepoint event] kmem:mm_page_alloc_zone_locked [Tracepoint event] xen:xen_mmu_alloc_ptpage [Tracepoint event] # And it works for all types of events: # perf list br List of pre-defined events (to be used in -e): branch-instructions OR branches [Hardware event] branch-misses [Hardware event] branch-load-misses [Hardware cache event] branch-loads [Hardware cache event] branch-instructions OR cpu/branch-instructions/ [Kernel PMU event] branch-misses OR cpu/branch-misses/ [Kernel PMU event] filelock:break_lease_block [Tracepoint event] filelock:break_lease_noblock [Tracepoint event] filelock:break_lease_unblock [Tracepoint event] syscalls:sys_enter_brk [Tracepoint event] syscalls:sys_exit_brk [Tracepoint event] # Suggested-by: -
Adrian Hunter authored
Adjust the validation to allow for max_stack greater than PERF_MAX_STACK_DEPTH. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lkml.kernel.org/r/1443186956-18718-18-git-send-email-adrian.hunter@intel.comSigned-off-by:
-
Namhyung Kim authored
The patch f9db0d0f ("perf callchain: Allow disabling call graphs per event") added an ability to enable/disable callchain recording per event. But it had a problem when the enablement setting is changed at 'perf report' time using -g/--call-graph option. For example, the following scenario will get a segfault. $ perf record -ag sleep 1 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.500 MB perf.data (2555 samples) ] $ perf report -g none perf: Segmentation fault -------- backtrace -------- perf[0x53a98a] /usr/lib/libc.so.6(+0x335af)[0x7f4e91df95af] This is because callchain_param.sort() callback was not set but it tried to call the function as it had the PERF_SAMPLE_CALLCHAIN bit. Signed-off-by:
Namhyung Kim <namhyung@kernel.org> Tested-by:
-
Namhyung Kim authored
The perf top didn't add the idle/swapper thread to the machine's thread list and its comm was displayed as ':0'. Fix it. Signed-off-by:
-
Namhyung Kim authored
The perf top uses 'dso,symbol' sort keys by default so it overlooked a problem in task's comm resolving. When the sort key contains 'comm', some task's comm is not shown properly. This is because the perf_top__mmap_read_idx() checks the cpumode value improperly. The cpumode value of non-sample events are 0 (PERF_RECORD_MISC_CPUMODE_ UNKNOWN) so the events will be ignored by the switch statement. This patch allows it for non-sample events. Signed-off-by:
-
Namhyung Kim authored
A previous patch added a synthesized comm event for forked child process but it missed that the event should contain area for sample_id_hdr at the end. It worked by accident since the perf_event union contains bigger event structs like mmap_events. This patch fixes it by dynamically allocating event struct including those area like in perf_event__synthesize_thread_map(). Reported-by:
Arnaldo Carvalho de Melo <acme@kernel.org> Signed-off-by:
-
Vaishali Thakkar authored
The DEFINE_PCI_DEVICE_TABLE() macro is deprecated. Use 'struct pci_device_id' instead of DEFINE_PCI_DEVICE_TABLE(), with the goal of getting rid of this macro completely. This Coccinelle semantic patch performs this transformation: @@ identifier a; declarer name DEFINE_PCI_DEVICE_TABLE; initializer i; @@ - DEFINE_PCI_DEVICE_TABLE(a) + const struct pci_device_id a[] = i; Signed-off-by:
Vaishali Thakkar <vthakkar1994@gmail.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/20151001085201.GA16939@localhostSigned-off-by:
-
Ingo Molnar authored
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core Pull perf/core improvements and fixes: User visible changes: - By default use the most precise "cycles" hw counter available, i.e. when the user doesn't specify any event, it will try using cycles:ppp, cycles:pp, etc. (Arnaldo Carvalho de Melo) - Remove blank lines, headers when piping output in 'perf list', so that it can be sanely used with 'wc -l', etc. (Arnaldo Carvalho de Melo) - Amend documentation about max_stack and synthesized callchains. (Adrian Hunter) - Fix 'perf probe -l' for probes added to kernel module functions. (Masami Hiramatsu) Build fixes: - Fix shadowed declarations that break the build on older distros. (Jiri Olsa) - Fix build break on powerpc due to sample_reg_masks. (Sukadev Bhattiprolu) Signed-off-by:
-
- 30 Sep, 2015 8 commits
-
-
Arnaldo Carvalho de Melo authored
If the user doesn't specify any event, try the most precise "cycles" available, i.e. start by "cycles:ppp" and go on removing "p" till it works. E.g. $ perf record usleep 1 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.017 MB perf.data (11 samples) ] $ perf evlist cycles:pp $ perf evlist -v cycles:pp: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|PERIOD, disabled: 1, inherit: 1, mmap: 1, comm: 1, freq: 1, enable_on_exec: 1, task: 1, precise_ip: 2, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1 $ grep 'model name' /proc/cpuinfo | head -1 model name : Intel(R) Core(TM) i7-3667U CPU @ 2.00GHz $ When 'cycles' appears explicitely is specified this will not be tried, i.e. the user has full control of the level of precision to be used: $ perf record -e cycles usleep 1 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.016 MB perf.data (9 samples) ] $ perf evlist cycles $ perf evlist -v cycles: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|PERIOD, disabled: 1, inherit: 1, mmap: 1, comm: 1, freq: 1, enable_on_exec: 1, task: 1, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1 $ Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Chandler Carruth <chandlerc@gmail.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Wang Nan <wangnan0@huawei.com> Link: https://www.youtube.com/watch?v=nXaxk27zwlk Link: http://lkml.kernel.org/n/tip-b1ywebmt22pi78vjxau01wth@git.kernel.orgSigned-off-by: -
Arnaldo Carvalho de Melo authored
So that one can, for instance, use it with wc -l: # perf list *:*write* | wc -l 60 Or to look for the "bio" tracepoints, without 'perf list' headers: # perf list *:*bio* | head block:block_bio_backmerge [Tracepoint event] block:block_bio_bounce [Tracepoint event] block:block_bio_complete [Tracepoint event] block:block_bio_frontmerge [Tracepoint event] block:block_bio_queue [Tracepoint event] block:block_bio_remap [Tracepoint event] # Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-ts7sc0x8u4io4cifzkup4j44@git.kernel.orgSigned-off-by: -
Masami Hiramatsu authored
perf probe shows more precisely message when it finds given %return target function is inlined. Without this fix: ---- # ./perf probe -V getname_flags%return Return probe must be on the head of a real function. Debuginfo analysis failed. Error: Failed to show vars. ---- With this fix: ---- # ./perf probe -V getname_flags%return Failed to find "getname_flags%return", because getname_flags is an inlined function and has no return point. Debuginfo analysis failed. Error: Failed to show vars. ---- Suggested-by: -
Masami Hiramatsu authored
perf probe --list will get a segfault if the first kprobe event is on a module and the second or latter one is on the kernel. e.g. ---- # ./perf probe -q -m pcspkr pcspkr_event # ./perf probe -q vfs_read # ./perf probe -l Segmentation fault (core dumped) ---- This is because the debuginfo_cache fails to handle NULL module name, which causes segfault on strcmp. (Note that strcmp("something", NULL) always causes segfault) To fix this debuginfo_cache__open always translates the NULL module name to "kernel" (this is correct, because NULL module name means opening the debuginfo for the kernel) ---- # ./perf probe -l probe:pcspkr_event (on pcspkr_event@drivers/input/misc/pcspkr.c in pcspkr) probe:vfs_read (on vfs_read@ksrc/linux-3/fs/read_write.c) ---- Signed-off-by: -
Masami Hiramatsu authored
Perf probe always failed to find appropriate line numbers because of failing to find .text start address offset from debuginfo. e.g. ---- # ./perf probe -m pcspkr pcspkr_event:5 Added new events: probe:pcspkr_event (on pcspkr_event:5 in pcspkr) probe:pcspkr_event_1 (on pcspkr_event:5 in pcspkr) You can now use it in all perf tools, such as: perf record -e probe:pcspkr_event_1 -aR sleep 1 # ./perf probe -l Failed to find debug information for address ffffffffa031f006 Failed to find debug information for address ffffffffa031f016 probe:pcspkr_event (on pcspkr_event+6 in pcspkr) probe:pcspkr_event_1 (on pcspkr_event+22 in pcspkr) ---- This fixes the above issue as below. 1. Get the relative address of the symbol in .text by using map->start. 2. Adjust the address by adding the offset of .text section in the kernel module binary. With this fix, perf probe -l shows lines correctly. ---- # ./perf probe -l probe:pcspkr_event (on pcspkr_event:5@drivers/input/misc/pcspkr.c in pcspkr) probe:pcspkr_event_1 (on pcspkr_event:5@drivers/input/misc/pcspkr.c in pcspkr) ---- Reported-by: -
Masami Hiramatsu authored
Fix a trival bug about libdwfl usage of the report session, it should explicitly begin and end a report session around dwfl_report_offline(). Signed-off-by:
-
Masami Hiramatsu authored
Fix to remove dot suffix (e.g. .const, .isra) from the second or latter events which has suffix numbers. Since the previous commit 35a23ff9 ("perf probe: Cut off the gcc optimization postfixes from function name") didn't care about the suffix numbered events, therefore we'll have an error when we add additional events on the same dot suffix functions. e.g. ---- # ./perf probe -f -a get_sigframe.isra.2.constprop.3 \ -a get_sigframe.isra.2.constprop.3 Failed to write event: Invalid argument Error: Failed to add events. ---- This fixes above issue as below: ---- # ./perf probe -f -a get_sigframe.isra.2.constprop.3 \ -a get_sigframe.isra.2.constprop.3 Added new events: probe:get_sigframe (on get_sigframe.isra.2.constprop.3) probe:get_sigframe_1 (on get_sigframe.isra.2.constprop.3) You can now use it in all perf tools, such as: perf record -e probe:get_sigframe_1 -aR sleep 1 ---- Signed-off-by:
-
Arnaldo Carvalho de Melo authored
Map 't', 'T' (text, local, global), 'w' and 'W' (weak text, local, global) as STT_FUNC, and the rest as STT_OBJECT Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-sbwcixulpc5v1xuxn3xvm0nn@git.kernel.orgSigned-off-by:
-
