Add a property to keep the analog calibration cell powered.
This feature is specific to the Microchip SDHCI IP and outside
of the standard SDHCI register map.

By always keeping it on, after a full reset sequence, we make sure
that this feature is activated and not disabled.

We expose a hardware property to the DT as this feature can be used
to adapt SDHCI behavior vs. how the SDCAL SoC pin is connected
on the board.

Note that managing properly this property would reduce
power consumption on some SAMA5D2 SiP revisions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add the specific microchip,sdcal-inverted property to at91 sdhci
device binding.
This optional property describes how the SoC SDCAL pin is connected.
It could be handled at SiP, SoM or board level.

This property read by at91 sdhci driver will allow to put in place a
software workaround that would reduce power consumption.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Make sdmmc_idma_validate_data to avoid the following warning
from sparse:

drivers/mmc/host/mmci_stm32_sdmmc.c:28:5: warning: symbol 'sdmmc_idma_validate_data' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add PCI Ids for Intel JSL.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for low power mode to the Ingenic's MMC/SD Controller.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for probing mmc driver on the X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add the MMC bindings for the X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for probing mmc driver on the JZ4760 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add the MMC bindings for the JZ4760 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for 8bit mode, now supports 1bit/4bit/8bit modes.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix sparse warnings:

drivers/mmc/host/sdhci-pci-core.c:1599:6: warning: symbol 'amd_sdhci_reset' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.

Therefore, add a new compatible, to adapt the Intel's LGM
SDXC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a new compatible to use the sdhc-arasan host controller driver
with the SDXC PHY to support on Intel's Lightning Mountain(LGM) SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds a specific busy_complete callback for sdmmc variant.

sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.

The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds busy_completion callback at mmci_host_ops
to allow to define a specific busy completion by variant.

The legacy code corresponding to busy completion used
by ux500 variants is moved to ux500_busy_complete function.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the stm32_sdmmc variant, the datatimer is active not only during
data transfers with the DPSM, but also while waiting for the busyend
IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an
incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which
simply breaks the behaviour.

Address this by updating the datatimer value before sending a command
having the MMC_RSP_BUSY flag set. To inform the mmc core about the
maximum supported busy timeout, which also depends on the current
clock rate, set ->max_busy_timeout (in ms).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix the following sparse warnings by making any functions not used
outsde the mmci.c driver static.

drivers/mmc/host/mmci.c:422:6: warning: symbol 'mmci_dma_release' was not declared. Should it be static?
drivers/mmc/host/mmci.c:430:6: warning: symbol 'mmci_dma_setup' was not declared. Should it be static?
drivers/mmc/host/mmci.c:465:5: warning: symbol 'mmci_prep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:481:6: warning: symbol 'mmci_unprep_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:490:6: warning: symbol 'mmci_get_next_data' was not declared. Should it be static?
drivers/mmc/host/mmci.c:498:5: warning: symbol 'mmci_dma_start' was not declared. Should it be static?
drivers/mmc/host/mmci.c:533:6: warning: symbol 'mmci_dma_finalize' was not declared. Should it be static?
drivers/mmc/host/mmci.c:542:6: warning: symbol 'mmci_dma_error' was not declared. Should it be static?
drivers/mmc/host/mmci.c:951:6: warning: symbol 'mmci_variant_init' was not declared. Should it be static?
drivers/mmc/host/mmci.c:956:6: warning: symbol 'ux500v2_variant_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are a couple of statements that are indented by an extra
space, clean this up by remove the extraneous spaces.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is a hunk of code that is indented one level too deep, fix
this by removing the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Simplify this function implementation by using a known wrapper function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.

Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

PM has been reworked, so eMMC gets now detected on R-Car H3 ES1.0 and
2.0 as well as M3-N without the workaround. Card detect and write
protect also still work. Remove the workaround.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add MAINTAINERS entry for Actions Semi SD/MMC driver with its binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently
supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is
supported but it is untested. There is no SDIO support for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add devicetree YAML binding for Actions Semi Owl SoC's SD/MMC/SDIO
controller.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SD Host controller on Milbeaut consists of two controller parts.
One is core controller F_SDH30, this is similar to sdhci-fujitsu
controller.
Another is bridge controller.
This bridge controller is not compatible with sdhci-fujitsu controller.
This is special for Milbeaut series. This has some functions.
For example, reset control, clock enable/select for SDR50/25/12, set
property of SD physical pins, retuning control, set capabilityies.

This bridge controller requires special procedures at reset or clock
enablement or change for further tuning of clock.
Signed-off-by: Takao Orito <orito.takao@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add the device-tree binding documentation for Milbeaut SDHCI driver.
Signed-off-by: Takao Orito <orito.takao@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

AMD SDHC 0x7906 requires a hard reset to clear all internal state.
Otherwise it can get into a bad state where the DATA lines are always
read as zeros.

This change requires firmware that can transition the device into
D3Cold for it to work correctly. If the firmware does not support
transitioning to D3Cold then the power state transitions are a no-op.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In sdhci_do_reset we call the reset callback which is typically
sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the
controller to reset. If SDHCI_RESET_ALL was passed as the flag, the
controller will clear the IRQ mask. If during that 100ms the card is
removed there is no notification to the MMC system that the card was
removed. So from the drivers point of view the card is always present.

By making sdhci_reinit compare the present state it can schedule a
rescan if the card was removed while a reset was in progress.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "A set of fixes that have trickled in over the last couple of weeks:

   - MAINTAINER update for Cavium/Marvell ThunderX2

   - stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
     CAN interfaces

   - i.MX fixes for voltage regulator GPIO mappings, fixes voltage
     scaling issues

   - More i.MX fixes for various issues on i.MX eval boards: interrupt
     storm due to u-boot leaving pins in new states, fixing power button
     config, a couple of compatible-string corrections.

   - Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets

   - A few documentation tweaks and a fix of a memory leak in the reset
     subsystem"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  MAINTAINERS: update Cavium ThunderX2 maintainers
  ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
  ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
  ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
  ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
  arm64: dts: zii-ultra: fix ARM regulator GPIO handle
  ARM: sunxi: Fix CPU powerdown on A83T
  ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
  arm64: dts: imx8mn: fix compatible string for sdma
  arm64: dts: imx8mm: fix compatible string for sdma
  reset: fix reset_control_ops kerneldoc comment
  ARM: dts: imx6-logicpd: Re-enable SNVS power key
  soc: imx: gpc: fix initialiser format
  ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
  arm64: dts: ls1028a: fix a compatible issue
  reset: fix reset_control_get_exclusive kerneldoc comment
  reset: fix reset_control_lookup kerneldoc comment
  reset: fix of_reset_control_get_count kerneldoc comment
  reset: fix of_reset_simple_xlate kerneldoc comment
  reset: Fix memory leak in reset_control_array_put()

Pull IIO fixes and staging driver from Greg KH:
 "Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole
  new staging driver.

  The IIO fixes resolve some reported issues, all are tiny.

  The staging driver addition is the vboxsf filesystem, which is the
  VirtualBox guest shared folder code. Hans has been trying to get
  filesystem reviewers to review the code for many months now, and
  Christoph finally said to just merge it in staging now as it is
  stand-alone and the filesystem people can review it easier over time
  that way.

  I know it's late for this big of an addition, but it is stand-alone.

  The code has been in linux-next for a while, long enough to pick up a
  few tiny fixes for it already so people are looking at it.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: Fix error return code in vboxsf_fill_super()
  staging: vboxsf: fix dereference of pointer dentry before it is null checked
  staging: vboxsf: Remove unused including <linux/version.h>
  staging: Add VirtualBox guest shared folder (vboxsf) support
  iio: adc: stm32-adc: fix stopping dma
  iio: imu: inv_mpu6050: fix no data on MPU6050
  iio: srf04: fix wrong limitation in distance measuring
  iio: imu: adis16480: make sure provided frequency is positive

Pull char/misc driver fixes from Greg KH:
 "Here are a number of late-arrival driver fixes for issues reported for
  some char/misc drivers for 5.4-rc7

  These all come from the different subsystem/driver maintainers as
  things that they had reports for and wanted to see fixed.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  intel_th: pci: Add Jasper Lake PCH support
  intel_th: pci: Add Comet Lake PCH support
  intel_th: msu: Fix possible memory leak in mode_store()
  intel_th: msu: Fix overflow in shift of an unsigned int
  intel_th: msu: Fix missing allocation failure check on a kstrndup
  intel_th: msu: Fix an uninitialized mutex
  intel_th: gth: Fix the window switching sequence
  soundwire: slave: fix scanf format
  soundwire: intel: fix intel_register_dai PDI offsets and numbers
  interconnect: Add locking in icc_set_tag()
  interconnect: qcom: Fix icc_onecell_data allocation
  soundwire: depend on ACPI || OF
  soundwire: depend on ACPI
  thunderbolt: Drop unnecessary read when writing LC command in Ice Lake
  thunderbolt: Fix lockdep circular locking depedency warning
  thunderbolt: Read DP IN adapter first two dwords in one go

Pull configfs regression fix from Christoph Hellwig:
 "Fix a regression from this merge window in the configfs symlink
  handling (Honggang Li)"

* tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs:
  configfs: calculate the depth of parent item

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes for x86:

   - Make the tsc=reliable/nowatchdog command line parameter work again.
     It was broken with the introduction of the early TSC clocksource.

   - Prevent the evaluation of exception stacks before they are set up.
     This causes a crash in dumpstack because the stack walk termination
     gets screwed up.

   - Prevent a NULL pointer dereference in the rescource control file
     system.

   - Avoid bogus warnings about APIC id mismatch related to the LDR
     which can happen when the LDR is not in use and therefore not
     initialized. Only evaluate that when the APIC is in logical
     destination mode"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early
  x86/dumpstack/64: Don't evaluate exception stacks before setup
  x86/apic/32: Avoid bogus LDR warnings
  x86/resctrl: Prevent NULL pointer dereference when reading mondata

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for timekeepoing and clocksource drivers:

   - VDSO data was updated conditional on the availability of a VDSO
     capable clocksource. This causes the VDSO functions which do not
     depend on a VDSO capable clocksource to operate on stale data.
     Always update unconditionally.

   - Prevent a double free in the mediatek driver

   - Use the proper helper in the sh_mtu2 driver so it won't attempt to
     initialize non-existing interrupts"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping/vsyscall: Update VDSO data unconditionally
  clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
  clocksource/drivers/mediatek: Fix error handling

Pull scheduler fixes from Thomas Gleixner:
 "Two fixes for scheduler regressions:

   - Plug a subtle race condition which was introduced with the rework
     of the next task selection functionality. The change of task
     properties became unprotected which can be observed inconsistently
     causing state corruption.

   - A trivial compile fix for CONFIG_CGROUPS=n"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix pick_next_task() vs 'change' pattern race
  sched/core: Fix compilation error when cgroup not selected

Pull perf tooling fixes from Thomas Gleixner:

 - Fix the time sorting algorithm which was broken due to truncation of
   big numbers

 - Fix the python script generator fail caused by a broken tracepoint
   array iterator

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Fix time sorting
  perf tools: Remove unused trace_find_next_event()
  perf scripting engines: Iterate on tep event arrays directly

Pull irq fixlet from Thomas Gleixner:
 "A trivial fix for a kernel doc regression where an argument change was
  not reflected in the documentation"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation