bgmac uses bcm47xx_nvram.h which is only available when BCM47XX was
selected. Earlier BCMA_HOST_SOC depended on BCM47XX so this was not
build on any other archs, but that changed. We should modify this
driver to get access to the nvram or the variables through platform
data.

This fixes a build problem in linux-next reported by Stephen Rothwell:

drivers/net/ethernet/broadcom/bgmac.c:19:27: fatal error: bcm47xx_nvram.h: No such file or directory
 #include <bcm47xx_nvram.h>
                           ^
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

taken from Ralink linux and windows drivers:

0x1b75, 0x7733 AirLive 450Mbps Wireless-N Dual Band USB Adapter
0x0b05, 0x17bc ASUS USB-N66 450Mbps Dual Band USB Adapter
0x0b05, 0x17ad ASUS USB-N66 Dual Band N Network Adapter
0x050d, 0x1103 Belkin Wireless Adapter
0x148f, 0xf301 Cameo Ralink3573 3x3 single band USB dongle
0x7392, 0x7733 Edimax
0x0e66, 0x0020 Hawking HD45U Dual Band USB Wireless-N Adapter
0x0e66, 0x0021 Hawking HD45U Dual Band Wls-450N Adapter
0x04bb, 0x094e I-O DATA WN-AG450U Wireless LAN Adapter
0x0789, 0x016b Logitec LAN-W450AN/U2
0x0846, 0x9012 NETGEAR WNDA4100 N900 Wireless Dual Band USB Adapter
0x0846, 0x9019 NETGEAR WNDA4200D Wireless Dual Band USB Adapter
0x2019, 0xed19 Planex GW-USDual450
0x148f, 0x3573 Ralink 802.11n USB Wireless LAN Card
0x0df6, 0x0067 Sitecom Wireless Dualband Network Adapter N750 X6
0x0df6, 0x006a Sitecom Wireless Dualband Network Adapter N900 X7
0x0586, 0x3421 ZyXEL Dual-Band Wireless N450 USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When antenna diversity combining is enabled in the EEPROM,
the initial values for the MAIN/ALT config have to be
programmed correctly. This patch adds it for AR9285.

Since the diversity combining macros are common to all chip
families, remove the redundant AR9285 macros and move the
definitions to phy.h.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We support maximum simultaneous 2 non-AP station interfaces and
they can assume role of Station/P2P client/P2P GO.
Advertise this support to cfg80211 so that concurrent P2P/STA
operation is possible.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We already have 'struct mwifiex_ie_types_header' with same
definition. Hence host_cmd_tlv is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For PCIe cards, when wrong firmware is downloaded, firmware is
failed to be ready in 10 seconds. We should return an error at
this point. But currently we are sending first command to firmware.
As expected firmware doesn't respond to this command and command
timeout occurs.

This patch fixes the problem by removing unnecessary 'ret'
variable modifications in "if (ret) {" block.
The block is just supposed to update "adapter->winner" flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.

Replace mdelay with msleep(non-blocking API) to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.

This patch removes 1000 retries macro usage, because 100secs
time is not practical.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().

USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.

Also, this change matches our handling for SDIO and PCIe
interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().

Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.

scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is bug fix for an invalid boundry check for WPS IE.
We should check max IE length against defined macro; instead we were
checking it against size of pointer. Fix it.
Also move IE length check before allocation of memory.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During P2P handshake, P2P client needs to send deauth after EAPOL
FAILURE to GO. We need add bss mode for P2P client when handle deauth
request.

Without this change, deauth can not be sent out from P2P client side.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Before sending command to firmware, we need to check the frame type.
We skip registering the mgmt frame that has already been registered.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some GO will send deauth or disassoc packet at the end of WPS
handshake, which causes P2P connecion failure due to the race
condition between event path and data path.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In function 'mwifiex_write_data_complete' it need tx info to find
the mwifiex_private to updates statistics and wake up tx queues.
Or we may trigger tx queues timeout when transmitting lots of mgmt
frames.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Maintain total outstanding packet count for RA list instead of total
outstanding size as packet count metric seems more reasonable for
checking threshold etc.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pkt_count is used to determine if BA can be formed on this RA list
by comparing it with randomly generated BA threshold. The pkt_count
variable name here is ambiguous and does not reflect its usage
correctly. Rename it to ba_pkt_count.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under uAP mode mwifiex may stop all net tx queues on forwarding
packets. This may stop some tx queues and they never have chance
to be waked up. There is also no need to check tx_pending and
stop queues here. Because local host has such kind of check when
transmitting packets and it's not proper to have forwarding affect
local transmitting.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Steinar reported reallocations of skb->head with IPv6, leading to
a warning in skb_try_coalesce()

It turns out iwl3945 has several problems :

1) skb->truesize is underestimated.
   We really consume PAGE_SIZE bytes for a fragment,
   not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Stewart <pstew@google.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In production code, don't use -Werror,
as it causes random compilation failures due to compiler version and options used.

With every new version of gcc, it becomes stricter and report more warnings.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The git tree is in github.com nowadays.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I forgot to add an entry to MAINTAINERS when submitting the driver.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for TCP and UDP HW checksum offloading.
RX chain is allways configured for offload mode.
In case of checksum error in RX path the DMA L4 error bit(5)
will be set to 1 and driver will drop the packet.
TX checksum offloading is configrable (ethtool -K).
TX descriptors are configured for checksum offload according
to the SKB protocol type (TCP/UDP, IPV4/6), Upon mismatch drop
the TX packet (checksum required but not TCP/UDP IPV4/6 type).
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Release fragments in the order of allocation; including one for skb head
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Note that the driver doesn't directly use this field, but it should be
correctly defined in any case.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* CUS217 specific initvals have to be programmed.
* iniAdditional is not used for AR9462/AR9565, remove it.
* Handle channel 2484 for regulatory compliance.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Right now, even though these chips support cross-band
FCC, the code is non-functional since we bail out early if
the channelFlags differ. Fix this so that cross-band
FCC works for cards that support this feature.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next 99e94940:
brcmsmac: Reduce log spam in heavy tx, make err print in debug

 brcmsmac bcma0:0: phyerr 0x10, rate 0x14
 brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The return value of bcma_erom_get_addr_desc() is a unsigned value and it
could wrap around in the two complement writing. This happens for one
core in the BCM4708 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is better to return the actual error code than just -1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To make it possible to use the SoC host interface with ARM SoCs do not
depend on the MIPS driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>