- 23 Feb, 2017 40 commits
-
-
Richard Weinberger authored
commit 843741c5 upstream. When the operation fails we also have to undo the changes we made to ->xattr_names. Otherwise listxattr() will report wrong lengths. Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Patrick Scheuring authored
commit da25311c upstream. The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop. Therefore it also needs a keyboard reset to detect the Elantech touchpad. Otherwise the touchpad appears to be dead. With this patch the touchpad is detected: $ dmesg | grep -E "(i8042|Elantech|elantech)" [ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.680372] i8042: Attempting to reset device connected to KBD port [ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e) [ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f. [ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74 [ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6 Signed-off-by:
Patrick Scheuring <patrick.scheuring.dev@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Jan Kara authored
commit a2ed0b39 upstream. When isofs_mount() is called to mount a device read-write, it returns EACCES even before it checks that the device actually contains an isofs filesystem. This may confuse mount(8) which then tries to mount all subsequent filesystem types in read-only mode. Fix the problem by returning EACCES only once we verify that the device indeed contains an iso9660 filesystem. Fixes: 17b7f7cfReported-by:
Kent Overstreet <kent.overstreet@gmail.com> Reported-by:
Karel Zak <kzak@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Dan Carpenter authored
commit e7cb08e8 upstream. We accidentally overwrite the original saved value of "flags" so that we can't re-enable IRQs at the end of the function. Presumably this function is mostly called with IRQs disabled or it would be obvious in testing. Fixes: aceeffbb ("zfcp: trace full payload of all SAN records (req,resp,iels)") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johannes Berg authored
commit ea720935 upstream. In mac80211, multicast A-MSDUs are accepted in many cases that they shouldn't be accepted in: * drop A-MSDUs with a multicast A1 (RA), as required by the spec in 9.11 (802.11-2012 version) * drop A-MSDUs with a 4-addr header, since the fourth address can't actually be useful for them; unless 4-address frame format is actually requested, even though the fourth address is still not useful in this case, but ignored Accepting the first case, in particular, is very problematic since it allows anyone else with possession of a GTK to send unicast frames encapsulated in a multicast A-MSDU, even when the AP has client isolation enabled. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Ming Lei authored
commit bcd8f2e9 upstream. This patch fixes one use-after-free report[1] by KASAN. In __scsi_scan_target(), when a type 31 device is probed, SCSI_SCAN_TARGET_PRESENT is returned and the target will be scanned again. Inside the following scsi_report_lun_scan(), one new scsi_device instance is allocated, and scsi_probe_and_add_lun() is called again to probe the target and still see type 31 device, finally __scsi_remove_device() is called to remove & free the device at the end of scsi_probe_and_add_lun(), so cause use-after-free in scsi_report_lun_scan(). And the following SCSI log can be observed: scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36 scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0 scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added scsi 0:0:2:0: scsi scan: Sending REPORT LUNS to (try 0) scsi 0:0:2:0: scsi scan: REPORT LUNS successful (try 0) result 0x0 scsi 0:0:2:0: scsi scan: REPORT LUN scan scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36 scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0 scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added BUG: KASAN: use-after-free in __scsi_scan_target+0xbf8/0xe40 at addr ffff88007b44a104 This patch fixes the issue by moving the putting reference at the end of scsi_report_lun_scan(). [1] KASAN report ================================================================== [ 3.274597] PM: Adding info for serio:serio1 [ 3.275127] BUG: KASAN: use-after-free in __scsi_scan_target+0xd87/0xdf0 at addr ffff880254d8c304 [ 3.275653] Read of size 4 by task kworker/u10:0/27 [ 3.275903] CPU: 3 PID: 27 Comm: kworker/u10:0 Not tainted 4.8.0 #2121 [ 3.276258] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014 [ 3.276797] Workqueue: events_unbound async_run_entry_fn [ 3.277083] ffff880254d8c380 ffff880259a37870 ffffffff94bbc6c1 ffff880078402d80 [ 3.277532] ffff880254d8bb80 ffff880259a37898 ffffffff9459fec1 ffff880259a37930 [ 3.277989] ffff880254d8bb80 ffff880078402d80 ffff880259a37920 ffffffff945a0165 [ 3.278436] Call Trace: [ 3.278528] [<ffffffff94bbc6c1>] dump_stack+0x65/0x84 [ 3.278797] [<ffffffff9459fec1>] kasan_object_err+0x21/0x70 [ 3.279063] device: 'psaux': device_add [ 3.279616] [<ffffffff945a0165>] kasan_report_error+0x205/0x500 [ 3.279651] PM: Adding info for No Bus:psaux [ 3.280202] [<ffffffff944ecd22>] ? kfree_const+0x22/0x30 [ 3.280486] [<ffffffff94bc2dc9>] ? kobject_release+0x119/0x370 [ 3.280805] [<ffffffff945a0543>] __asan_report_load4_noabort+0x43/0x50 [ 3.281170] [<ffffffff9507e1f7>] ? __scsi_scan_target+0xd87/0xdf0 [ 3.281506] [<ffffffff9507e1f7>] __scsi_scan_target+0xd87/0xdf0 [ 3.281848] [<ffffffff9507d470>] ? scsi_add_device+0x30/0x30 [ 3.282156] [<ffffffff94f7f660>] ? pm_runtime_autosuspend_expiration+0x60/0x60 [ 3.282570] [<ffffffff956ddb07>] ? _raw_spin_lock+0x17/0x40 [ 3.282880] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160 [ 3.283200] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0 [ 3.283563] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250 [ 3.283882] [<ffffffff9507efc1>] do_scan_async+0x41/0x450 [ 3.284173] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610 [ 3.284492] [<ffffffff941a8954>] ? pwq_dec_nr_in_flight+0x124/0x2a0 [ 3.284876] [<ffffffff941d1770>] ? preempt_count_add+0x130/0x160 [ 3.285207] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0 [ 3.285526] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0 [ 3.285844] [<ffffffff941aa810>] ? process_one_work+0x12d0/0x12d0 [ 3.286182] [<ffffffff941bb365>] kthread+0x1c5/0x260 [ 3.286443] [<ffffffff940855cd>] ? __switch_to+0x88d/0x1430 [ 3.286745] [<ffffffff941bb1a0>] ? kthread_worker_fn+0x5a0/0x5a0 [ 3.287085] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40 [ 3.287368] [<ffffffff941bb1a0>] ? kthread_worker_fn+0x5a0/0x5a0 [ 3.287697] Object at ffff880254d8bb80, in cache kmalloc-2048 size: 2048 [ 3.288064] Allocated: [ 3.288147] PID = 27 [ 3.288218] [<ffffffff940b27ab>] save_stack_trace+0x2b/0x50 [ 3.288531] [<ffffffff9459f246>] save_stack+0x46/0xd0 [ 3.288806] [<ffffffff9459f4bd>] kasan_kmalloc+0xad/0xe0 [ 3.289098] [<ffffffff9459c07e>] __kmalloc+0x13e/0x250 [ 3.289378] [<ffffffff95078e5a>] scsi_alloc_sdev+0xea/0xcf0 [ 3.289701] [<ffffffff9507de76>] __scsi_scan_target+0xa06/0xdf0 [ 3.290034] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160 [ 3.290362] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0 [ 3.290724] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250 [ 3.291055] [<ffffffff9507efc1>] do_scan_async+0x41/0x450 [ 3.291354] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610 [ 3.291695] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0 [ 3.292022] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0 [ 3.292325] [<ffffffff941bb365>] kthread+0x1c5/0x260 [ 3.292594] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40 [ 3.292886] Freed: [ 3.292945] PID = 27 [ 3.293016] [<ffffffff940b27ab>] save_stack_trace+0x2b/0x50 [ 3.293327] [<ffffffff9459f246>] save_stack+0x46/0xd0 [ 3.293600] [<ffffffff9459fa61>] kasan_slab_free+0x71/0xb0 [ 3.293916] [<ffffffff9459bac2>] kfree+0xa2/0x1f0 [ 3.294168] [<ffffffff9508158a>] scsi_device_dev_release_usercontext+0x50a/0x730 [ 3.294598] [<ffffffff941ace9a>] execute_in_process_context+0xda/0x130 [ 3.294974] [<ffffffff9508107c>] scsi_device_dev_release+0x1c/0x20 [ 3.295322] [<ffffffff94f566f6>] device_release+0x76/0x1e0 [ 3.295626] [<ffffffff94bc2db7>] kobject_release+0x107/0x370 [ 3.295942] [<ffffffff94bc29ce>] kobject_put+0x4e/0xa0 [ 3.296222] [<ffffffff94f56e17>] put_device+0x17/0x20 [ 3.296497] [<ffffffff9505201c>] scsi_device_put+0x7c/0xa0 [ 3.296801] [<ffffffff9507e1bc>] __scsi_scan_target+0xd4c/0xdf0 [ 3.297132] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160 [ 3.297458] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0 [ 3.297829] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250 [ 3.298156] [<ffffffff9507efc1>] do_scan_async+0x41/0x450 [ 3.298453] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610 [ 3.298777] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0 [ 3.299105] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0 [ 3.299408] [<ffffffff941bb365>] kthread+0x1c5/0x260 [ 3.299676] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40 [ 3.299967] Memory state around the buggy address: [ 3.300209] ffff880254d8c200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 3.300608] ffff880254d8c280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 3.300986] >ffff880254d8c300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 3.301408] ^ [ 3.301550] ffff880254d8c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 3.301987] ffff880254d8c400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 3.302396] ================================================================== Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Paul Mackerras authored
commit 1a34439e upstream. Debugging a data corruption issue with virtio-net/vhost-net led to the observation that __copy_tofrom_user was occasionally returning a value 16 larger than it should. Since the return value from __copy_tofrom_user is the number of bytes not copied, this means that __copy_tofrom_user can occasionally return a value larger than the number of bytes it was asked to copy. In turn this can cause higher-level copy functions such as copy_page_to_iter_iovec to corrupt memory by copying data into the wrong memory locations. It turns out that the failing case involves a fault on the store at label 79, and at that point the first unmodified byte of the destination is at R3 + 16. Consequently the exception handler for that store needs to add 16 to R3 before using it to work out how many bytes were not copied, but in this one case it was not adding the offset to R3. To fix it, this moves the label 179 to the point where we add 16 to R3. I have checked manually all the exception handlers for the loads and stores in this code and the rest of them are correct (it would be excellent to have an automated test of all the exception cases). This bug has been present since this code was initially committed in May 2002 to Linux version 2.5.20. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Ondrej Mosnáček authored
commit 50d2e6dc upstream. The cipher block size for GCM is 16 bytes, and thus the CTR transform used in crypto_gcm_setkey() will also expect a 16-byte IV. However, the code currently reserves only 8 bytes for the IV, causing an out-of-bounds access in the CTR transform. This patch fixes the issue by setting the size of the IV buffer to 16 bytes. Fixes: 84c91152 ("[CRYPTO] gcm: Add support for async ciphers") Signed-off-by:
Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Miklos Szeredi authored
commit cb3ae6d2 upstream. Make sure userspace filesystem is returning a well formed list of xattr names (zero or more nonzero length, null terminated strings). [Michael Theall: only verify in the nonzero size case] Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Miklos Szeredi authored
commit a09f99ed upstream. Fuse allowed VFS to set mode in setattr in order to clear suid/sgid on chown and truncate, and (since writeback_cache) write. The problem with this is that it'll potentially restore a stale mode. The poper fix would be to let the filesystems do the suid/sgid clearing on the relevant operations. Possibly some are already doing it but there's no way we can detect this. So fix this by refreshing and recalculating the mode. Do this only if ATTR_KILL_S[UG]ID is set to not destroy performance for writes. This is still racy but the size of the window is reduced. Signed-off-by:
-
Miklos Szeredi authored
commit 5e2b8828 upstream. Without "default_permissions" the userspace filesystem's lookup operation needs to perform the check for search permission on the directory. If directory does not allow search for everyone (this is quite rare) then userspace filesystem has to set entry timeout to zero to make sure permissions are always performed. Changing the mode bits of the directory should also invalidate the (previously cached) dentry to make sure the next lookup will have a chance of updating the timeout, if needed. Reported-by:
Jean-Pierre André <jean-pierre.andre@wanadoo.fr> Signed-off-by:
-
Sascha Silbe authored
commit 6cd997db upstream. con3270 contains an optimisation that reduces the amount of data to be transmitted to the 3270 terminal by putting a Repeat to Address (RA) order into the data stream. The RA order itself takes up space, so con3270 only uses it if there's enough space left in the line buffer. Otherwise it just pads out the line manually. For lines that were _just_ short enough that the RA order still fit in the line buffer, the line was instead padded with an insufficient amount of spaces. This was caused by examining the size of the allocated line buffer rather than the length of the string to be displayed. For con3270_cline_end(), we just compare against the line length. For con3270_update_string() however that isn't available anymore, so we check whether the Repeat to Address order is present. Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Tested-by:
Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by:
Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by:
Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Sascha Silbe authored
commit c14f2aac upstream. con3270 contains an optimisation that reduces the amount of data to be transmitted to the 3270 terminal by putting a Repeat to Address (RA) order into the data stream. The RA order itself takes up space, so con3270 only uses it if there's enough space left in the line buffer. Otherwise it just pads out the line manually. For lines too long to include the RA order, one byte was left uninitialised. This was caused by an off-by-one bug in the loop that pads out the line. Since the buffer is allocated from a common pool, the single byte left uninitialised contained some previous buffer content. Usually this was just a space or some character (which can result in clutter but is otherwise harmless). Sometimes, however, it was a Repeat to Address order, messing up the entire screen layout and causing the display to send the entire buffer content on every keystroke. Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Reported-by:
-
gmail authored
commit e81d4477 upstream. The commit 6050d47a: "ext4: bail out from make_indexed_dir() on first error" could end up leaking bh2 in the error path. [ Also avoid renaming bh2 to bh, which just confuses things --tytso ] Signed-off-by:
yangsheng <yngsion@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Anton Blanchard authored
commit 5045ea37 upstream. __kernel_get_syscall_map() and __kernel_clock_getres() use cmpli to check if the passed in pointer is non zero. cmpli maps to a 32 bit compare on binutils, so we ignore the top 32 bits. A simple test case can be created by passing in a bogus pointer with the bottom 32 bits clear. Using a clk_id that is handled by the VDSO, then one that is handled by the kernel shows the problem: printf("%d\n", clock_getres(CLOCK_REALTIME, (void *)0x100000000)); printf("%d\n", clock_getres(CLOCK_BOOTTIME, (void *)0x100000000)); And we get: 0 -1 The bigger issue is if we pass a valid pointer with the bottom 32 bits clear, in this case we will return success but won't write any data to the pointer. I stumbled across this issue because the LLVM integrated assembler doesn't accept cmpli with 3 arguments. Fix this by converting them to cmpldi. Fixes: a7f290da ("[PATCH] powerpc: Merge vdso's and add vdso support to 32 bits kernel") Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Trond Myklebust authored
commit 304020fe upstream. If the file permissions change on the server, then we may not be able to recover open state. If so, we need to ensure that we mark the file descriptor appropriately. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Tested-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Kyle Jones authored
commit decc5360 upstream. Signed-off-by:
Kyle Jones <kyle@kf5jwc.us> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Daniel Glöckner authored
commit 0ed50abb upstream. CMD23 aka SET_BLOCK_COUNT was introduced with MMC v3.1. Older versions of the specification allowed to terminate multi-block transfers only with CMD12. The patch fixes the following problem: mmc0: new MMC card at address 0001 mmcblk0: mmc0:0001 SDMB-16 15.3 MiB mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 ... blk_update_request: I/O error, dev mmcblk0, sector 0 Buffer I/O error on dev mmcblk0, logical block 0, async page read mmcblk0: unable to read partition table Signed-off-by:
Daniel Glöckner <dg@emlix.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Jan Remmet authored
commit 8f9165c9 upstream. http://www.ti.com/lit/pdf/SWCZ010: DCDC o/p voltage can go higher than programmed value Impact: VDDI, VDD2, and VIO output programmed voltage level can go higher than expected or crash, when coming out of PFM to PWM mode or using DVFS. Description: When DCDC CLK SYNC bits are 11/01: * VIO 3-MHz oscillator is the source clock of the digital core and input clock of VDD1 and VDD2 * Turn-on of VDD1 and VDD2 HSD PFETis synchronized or at a constant phase shift * Current pulled though VCC1+VCC2 is Iload(VDD1) + Iload(VDD2) * The 3 HSD PFET will be turned-on at the same time, causing the highest possible switching noise on the application. This noise level depends on the layout, the VBAT level, and the load current. The noise level increases with improper layout. When DCDC CLK SYNC bits are 00: * VIO 3-MHz oscillator is the source clock of digital core * VDD1 and VDD2 are running on their own 3-MHz oscillator * Current pulled though VCC1+VCC2 average of Iload(VDD1) + Iload(VDD2) * The switching noise of the 3 SMPS will be randomly spread over time, causing lower overall switching noise. Workaround: Set DCDCCTRL_REG[1:0]= 00. Signed-off-by:
Jan Remmet <j.remmet@phytec.de> Signed-off-by:
Mark Brown <broonie@kernel.org> [bwh: Backported to 3.2: use tps65910_clear_bits()] Signed-off-by:
-
Anssi Hannula authored
commit eb1a74b7 upstream. The DragonFly quirk added in 42e3121d ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly") applies a custom dB map on the volume control when its range is reported as 0..50 (0 .. 0.2dB). However, there exists at least one other variant (hw v1.0c, as opposed to the tested v1.2) which reports a different non-sensical volume range (0..53) and the custom map is therefore not applied for that device. This results in all of the volume change appearing close to 100% on mixer UIs that utilize the dB TLV information. Add a fallback case where no dB TLV is reported at all if the control range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also restrict the quirk to only apply to the volume control as there is also a mute control which would match the check otherwise. Fixes: 42e3121d ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly") Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Reported-by:
David W <regulars@d-dub.org.uk> Tested-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: keep using dev_info()] Signed-off-by:
-
Jack Morgenstein authored
commit a7e1f049 upstream. When switching from polling-based fw commands to event-based fw commands, there is a race condition which could cause a fw command in another task to hang: that task will keep waiting for the polling sempahore, but may never be able to acquire it. This is due to mlx4_cmd_use_events, which "down"s the sempahore back to 0. During driver initialization, this is not a problem, since no other tasks which invoke FW commands are active. However, there is a problem if the driver switches to polling mode and then back to event mode during normal operation. The "test_interrupts" feature does exactly that. Running "ethtool -t <eth device> offline" causes the PF driver to temporarily switch to polling mode, and then back to event mode. (Note that for VF drivers, such switching is not performed). Fix this by adding a read-write semaphore for protection when switching between modes. Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Greg Kroah-Hartman authored
commit 2fae9e5a upstream. This patch fixes a NULL pointer dereference caused by a race codition in the probe function of the legousbtower driver. It re-structures the probe function to only register the interface after successfully reading the board's firmware ID. The probe function does not deregister the usb interface after an error receiving the devices firmware ID. The device file registered (/dev/usb/legousbtower%d) may be read/written globally before the probe function returns. When tower_delete is called in the probe function (after an r/w has been initiated), core dev structures are deleted while the file operation functions are still running. If the 0 address is mappable on the machine, this vulnerability can be used to create a Local Priviege Escalation exploit via a write-what-where condition by remapping dev->interrupt_out_buffer in tower_write. A forged USB device and local program execution would be required for LPE. The USB device would have to delay the control message in tower_probe and accept the control urb in tower_open whilst guest code initiated a write to the device file as tower_delete is called from the error in tower_probe. This bug has existed since 2003. Patch tested by emulated device. Reported-by:
James Patrick-Evans <james@jmp-e.com> Tested-by:
-
Takashi Iwai authored
commit db685779 upstream. The pointer callbacks of ali5451 driver may return the value at the boundary occasionally, and it results in the kernel warning like snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024 It seems that folding the position offset is enough for fixing the warning and no ill-effect has been seen by that. Reported-by:
Enrico Mioso <mrkiko.rs@gmail.com> Tested-by:
-
Pan Xinhui authored
commit 11b7e154 upstream. When we merge two contiguous partitions whose signatures are marked NVRAM_SIG_FREE, We need update prev's length and checksum, then write it to nvram, not cur's. So lets fix this mistake now. Also use memset instead of strncpy to set the partition's name. It's more readable if we want to fill up with duplicate chars . Fixes: fa2b4e54 ("powerpc/nvram: Improve partition removal") Signed-off-by:
Pan Xinhui <xinhui.pan@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
commit 07d0e9a8 upstream. If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ init complete following H_REG_CRQ. If this occurs, we can end up having called scsi_block_requests and not a resulting unblock until the init complete happens, which may never occur, and we end up hanging I/O requests. This patch ensures the host action stay set to IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and unblock unless we receive an init complete. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by:
-
Baoquan He authored
commit c3db901c upstream. The current code missed freeing domain id when free a domain of struct dma_ops_domain. Signed-off-by:
Baoquan He <bhe@redhat.com> Fixes: ec487d1a ('x86, AMD IOMMU: add domain allocation and deallocation functions') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Xin Long authored
commit 66388f2c upstream. Once a chunk is enqueued successfully, sctp queues can take care of it. Even if it is failed to transmit (like because of nomem), it should be put into retransmit queue. If sctp report this error to users, it confuses them, they may resend that msg, but actually in kernel sctp stack is in charge of retransmit it already. Besides, this error probably is not from the failure of transmitting current msg, but transmitting or retransmitting another msg's chunks, as sctp_outq_flush just tries to send out all transports' chunks. This patch is to make sctp_cmd_send_msg return avoid, and not return the transmit err back to sctp_sendmsg Fixes: 8b570dc9 ("sctp: only drop the reference on the datamsg after sending a msg") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Mike Galbraith authored
commit 420902c9 upstream. If we hold the superblock lock while calling reiserfs_quota_on_mount(), we can deadlock our own worker - mount blocks kworker/3:2, sleeps forever more. crash> ps|grep UN 715 2 3 ffff880220734d30 UN 0.0 0 0 [kworker/3:2] 9369 9341 2 ffff88021ffb7560 UN 1.3 493404 123184 Xorg 9665 9664 3 ffff880225b92ab0 UN 0.0 47368 812 udisks-daemon 10635 10403 3 ffff880222f22c70 UN 0.0 14904 936 mount crash> bt ffff880220734d30 PID: 715 TASK: ffff880220734d30 CPU: 3 COMMAND: "kworker/3:2" #0 [ffff8802244c3c20] schedule at ffffffff8144584b #1 [ffff8802244c3cc8] __rt_mutex_slowlock at ffffffff814472b3 #2 [ffff8802244c3d28] rt_mutex_slowlock at ffffffff814473f5 #3 [ffff8802244c3dc8] reiserfs_write_lock at ffffffffa05f28fd [reiserfs] #4 [ffff8802244c3de8] flush_async_commits at ffffffffa05ec91d [reiserfs] #5 [ffff8802244c3e08] process_one_work at ffffffff81073726 #6 [ffff8802244c3e68] worker_thread at ffffffff81073eba #7 [ffff8802244c3ec8] kthread at ffffffff810782e0 #8 [ffff8802244c3f48] kernel_thread_helper at ffffffff81450064 crash> rd ffff8802244c3cc8 10 ffff8802244c3cc8: ffffffff814472b3 ffff880222f23250 .rD.....P2.".... ffff8802244c3cd8: 0000000000000000 0000000000000286 ................ ffff8802244c3ce8: ffff8802244c3d30 ffff880220734d80 0=L$.....Ms .... ffff8802244c3cf8: ffff880222e8f628 0000000000000000 (.."............ ffff8802244c3d08: 0000000000000000 0000000000000002 ................ crash> struct rt_mutex ffff880222e8f628 struct rt_mutex { wait_lock = { raw_lock = { slock = 65537 } }, wait_list = { node_list = { next = 0xffff8802244c3d48, prev = 0xffff8802244c3d48 } }, owner = 0xffff880222f22c71, save_state = 0 } crash> bt 0xffff880222f22c70 PID: 10635 TASK: ffff880222f22c70 CPU: 3 COMMAND: "mount" #0 [ffff8802216a9868] schedule at ffffffff8144584b #1 [ffff8802216a9910] schedule_timeout at ffffffff81446865 #2 [ffff8802216a99a0] wait_for_common at ffffffff81445f74 #3 [ffff8802216a9a30] flush_work at ffffffff810712d3 #4 [ffff8802216a9ab0] schedule_on_each_cpu at ffffffff81074463 #5 [ffff8802216a9ae0] invalidate_bdev at ffffffff81178aba #6 [ffff8802216a9af0] vfs_load_quota_inode at ffffffff811a3632 #7 [ffff8802216a9b50] dquot_quota_on_mount at ffffffff811a375c #8 [ffff8802216a9b80] finish_unfinished at ffffffffa05dd8b0 [reiserfs] #9 [ffff8802216a9cc0] reiserfs_fill_super at ffffffffa05de825 [reiserfs] RIP: 00007f7b9303997a RSP: 00007ffff443c7a8 RFLAGS: 00010202 RAX: 00000000000000a5 RBX: ffffffff8144ef12 RCX: 00007f7b932e9ee0 RDX: 00007f7b93d9a400 RSI: 00007f7b93d9a3e0 RDI: 00007f7b93d9a3c0 RBP: 00007f7b93d9a2c0 R8: 00007f7b93d9a550 R9: 0000000000000001 R10: ffffffffc0ed040e R11: 0000000000000202 R12: 000000000000040e R13: 0000000000000000 R14: 00000000c0ed040e R15: 00007ffff443ca20 ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b Signed-off-by:
Mike Galbraith <efault@gmx.de> Acked-by:
Frederic Weisbecker <fweisbec@gmail.com> Acked-by:
Mike Galbraith <mgalbraith@suse.de> Signed-off-by:
-
Daeho Jeong authored
commit 93e3b4e6 upstream. Now, ext4_do_update_inode() clears high 16-bit fields of uid/gid of deleted and evicted inode to fix up interoperability with old kernels. However, it checks only i_dtime of an inode to determine whether the inode was deleted and evicted, and this is very risky, because i_dtime can be used for the pointer maintaining orphan inode list, too. We need to further check whether the i_dtime is being used for the orphan inode list even if the i_dtime is not NULL. We found that high 16-bit fields of uid/gid of inode are unintentionally and permanently cleared when the inode truncation is just triggered, but not finished, and the inode metadata, whose high uid/gid bits are cleared, is written on disk, and the sudden power-off follows that in order. Signed-off-by:
Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by:
Hobin Woo <hobin.woo@samsung.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 24b923f0 upstream. This device uses GPIOs: 28 to switch between analog and digital modes: on digital mode, it should be set to 1. The code that sets it on analog mode is OK, but it misses the logic that sets it on digital mode. Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> [bwh: Backported to 3.2: adjust filenames] Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 1871d718 upstream. The cx231xx_set_agc_analog_digital_mux_select() callers expect it to return 0 or an error. Returning a positive value makes the first attempt to switch between analog/digital to fail. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit dafb65fb upstream. On this frontend, it takes a while to start output normal TS data. That only happens on state S9. On S8, the TS output is enabled, but it is not reliable enough. However, the zigzag loop is too fast to let it sync. As, on practical tests, the zigzag software loop doesn't seem to be helping, but just slowing down the tuning, let's switch to hardware algorithm, as the tuners used on such devices are capable of work with frequency drifts without any help from software. Signed-off-by:
-
Larry Finger authored
commit 0c9d3491 upstream. Some RTL8821AE devices sold in Great Britain have the country code of 0x25 encoded in their EEPROM. This value is not tested in the routine that establishes the regulatory info for the chip. The fix is to set this code to have the same capabilities as the EU countries. In addition, the channels allowed for COUNTRY_CODE_ETSI were more properly suited for China and Israel, not the EU. This problem has also been fixed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Shao Fu authored
commit 02b5fffb upstream. Driver rtlwifi maintains its own regulatory information, The Chrome Autotest (https://www.chromium.org/chromium-os/testing/autotest-user-doc) showed some errors. This patch adds the necessary information for rtlwifi. Signed-off-by:
Shao Fu <shaofu@realtek.com> Signed-off-by:
-
Florian Westphal authored
commit 95a8d19f upstream. In case nf_conntrack_tuple_taken did not find a conflicting entry check that all entries in this hash slot were tested and restart in case an entry was moved to another chain. Reported-by:
Eric Dumazet <edumazet@google.com> Fixes: ea781f19 ("netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and get rid of call_rcu()") Signed-off-by:
Florian Westphal <fw@strlen.de> Acked-by:
Pablo Neira Ayuso <pablo@netfilter.org> [bwh: Backported to 3.2: - Adjust context - Use NF_CT_STAT_INC(), not the _ATOMIC variant, since we disable BHs] Signed-off-by:
-
Steffen Maier authored
commit aceeffbb upstream. This was lost with commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") but is necessary for problem determination, e.g. to see the currently active zone set during automatic port scan. For the large GPN_FT response (4 pages), save space by not dumping any empty residual entries. Signed-off-by:
Alexey Ishchuk <aishchuk@linux.vnet.ibm.com> Reviewed-by:
Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Steffen Maier authored
commit 94db3725 upstream. commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") started to add FC_CT_HDR_LEN which made zfcp dump random data out of bounds for RSPN GS responses because u.rspn.rsp is the largest and last field in the union of struct zfcp_fc_req. Other request/response types only happened to stay within bounds due to the padding of the union or due to the trace capping of u.gspn.rsp to ZFCP_DBF_SAN_MAX_PAYLOAD. Timestamp : ... Area : SAN Subarea : 00 Level : 1 Exception : - CPU id : .. Caller : ... Record id : 2 Tag : fsscth2 Request id : 0x... Destination ID : 0x00fffffc Payload short : 01000000 fc020000 80020000 00000000 xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx <=== 00000000 00000000 00000000 00000000 Payload length : 32 <=== struct zfcp_fc_req { [0] struct zfcp_fsf_ct_els ct_els; [56] struct scatterlist sg_req; [96] struct scatterlist sg_rsp; union { struct {req; rsp;} adisc; SIZE: 28+28= 56 struct {req; rsp;} gid_pn; SIZE: 24+20= 44 struct {rspsg; req;} gpn_ft; SIZE: 40*4+20=180 struct {req; rsp;} gspn; SIZE: 20+273= 293 struct {req; rsp;} rspn; SIZE: 277+16= 293 [136] } u; } SIZE: 432 Signed-off-by:
-
Steffen Maier authored
commit 771bf035 upstream. With commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") we lost the N_Port-ID where an ELS response comes from. With commit 7c7dc196 ("[SCSI] zfcp: Simplify handling of ct and els requests") we lost the N_Port-ID where a CT response comes from. It's especially useful if the request SAN trace record with D_ID was already lost due to trace buffer wrap. GS uses an open WKA port handle and ELS just a D_ID, and only for ELS we could get D_ID from QTCB bottom via zfcp_fsf_req. To cover both cases, add a new field to zfcp_fsf_ct_els and fill it in on request to use in SAN response trace. Strictly speaking the D_ID on SAN response is the FC frame's S_ID. We don't need a field for the other end which is always us. Signed-off-by:
-
Steffen Maier authored
commit 7c964ffe upstream. This information was lost with commit a54ca0f6 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") but is required to debug e.g. invalid handle situations. Signed-off-by:
-
Steffen Maier authored
commit d27a7cb9 upstream. Since commit a54ca0f6 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") HBA records no longer contain WWPN, D_ID, or LUN to reduce duplicate information which is already in REC records. In contrast to "regular" target ports, we don't use recovery to open WKA ports such as directory/nameserver, so we don't get REC records. Therefore, introduce pseudo REC running records without any actual recovery action but including D_ID of WKA port on open/close. Signed-off-by:
-
