[Why]
Color corruption can occur on bootup into a login
manager that applies a non-linear gamma LUT because
the LUT may not actually be powered on before writing.

It's cleared on the next full pipe reprogramming as
we switch to LUTB from LUTA and the pipe accessing
the LUT has taken it out of light sleep mode.

[How]
The MPCC_OGAM_MEM_PWR_FORCE register does not force
the current power mode when set to 0. It only forces
when set light sleep, deep sleep or shutdown.

The register to actually force power on and ignore
sleep modes is MPCC_OGAM_MEM_PWR_DIS - a value of 0
will enable power requests and a value of 1 will
disable them.

When PWR_FORCE!=0 is combined with PWR_DIS=0 then
MPCC OGAM memory is forced into the state specified
by the force bits.

If PWR_FORCE is 0 then it respects the mode specified
by MPCC_OGAM_MEM_LOW_PWR_MODE if the RAM LUT is not
in use.

We set that bit to shutdown on low power, but otherwise
it inherits from bootup defaults.

So for the fix:

1. Update the sequence to "force" power on when needed

We can use MPCC_OGAM_MEM_PWR_DIS for this to turn on the
memory even when the block is in bypass and pending to be
enabled for the next frame.

We need this for both low power enabled or disabled.

If we don't set this then we can run into issues when we
first program the LUT from bootup.

2. Don't apply FORCE_SEL

Once we enable power requests with DIS=0 we run into the
issue of the RAM being forced into light sleep and being
unusable for display output. Leave this 0 like we used to
for DCN20.

3. Rely on MPCC OGAM init to determine light sleep/deep sleep

MPC low power debug mode isn't enabled on any ASIC currently
but we'll respect the setting determined during init if it
is.

Lightly tested as working with IGT tests and desktop color
adjustment.

4. Change the MPC resource default for DCN30

It was interleaving the dcn20 and dcn30 versions before
depending on the sequence.

5. REG_WAIT for it to be on whenever we're powering up the
memory

Otherwise we can write register values too early and we'll
get corruption.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We added these in DMCUB for runtime feature detection
but we didn't have helpers to call these with DC error
handling/logging.

[How]
Add helpers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Hardware team remeasured, need to update timings
to increase latency slightly and avoid intermittent
underflows.

[How]
sr exit latency update.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit fd1c85d3

[Why]
We are not implementing the planned new HW sequence
to disable HUBP.

[How]
Revert most related changes to minimize possibility
of regression.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit f8e792dc

[Why]
We are not implementing the planned new HW
sequence for HUBP disable.

[How]
Revert most related changes to minimize regressions.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In following sequence driver will add counter twice on
same edp stream.
1. Boot into OS.
2. Set timing with edp only.
3. Set timing with edp and external monitor.
4. Set visibility on for edp.

Step 2 and 3 will add seamless boot counter twice and
subtract it once in step 4.

[How]
Remove global counter and calculate it is used.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
To get the pixel statistics on every frame, change ABM
sample rate from 2 to 1.

[How]
Change LS, HS and BL sample rate to 1.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use debugfs API directly instead of drm middle layer.

v2: squash in build fix (Alex)
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Retrieving radeon device struct from ring struct will be
used in next patch where debugfs's show function can only pass
one private data pointer.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove the 'radeon_packet3_check_t' typedef as it is not used.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/nislands_smc.h: Replace one-element array with flexible-array member in struct NISLANDS_SMC_SWSTATE

There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

Use flexible-array member in struct NISLANDS_SMC_SWSTATE, instead of
one-element array.

Also, this helps with the ongoing efforts to enable -Warray-bounds by
fixing the following warnings:

drivers/gpu/drm/radeon/ni_dpm.c: In function ‘ni_convert_power_state_to_smc’:
drivers/gpu/drm/radeon/ni_dpm.c:2521:20: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2521 |   smc_state->levels[i].dpm2.MaxPS =
      |   ~~~~~~~~~~~~~~~~~^~~
drivers/gpu/drm/radeon/ni_dpm.c:2523:20: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2523 |   smc_state->levels[i].dpm2.NearTDPDec = NISLANDS_DPM2_NEAR_TDP_DEC;
      |   ~~~~~~~~~~~~~~~~~^~~
drivers/gpu/drm/radeon/ni_dpm.c:2524:20: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2524 |   smc_state->levels[i].dpm2.AboveSafeInc = NISLANDS_DPM2_ABOVE_SAFE_INC;
      |   ~~~~~~~~~~~~~~~~~^~~
drivers/gpu/drm/radeon/ni_dpm.c:2525:20: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2525 |   smc_state->levels[i].dpm2.BelowSafeInc = NISLANDS_DPM2_BELOW_SAFE_INC;
      |   ~~~~~~~~~~~~~~~~~^~~
drivers/gpu/drm/radeon/ni_dpm.c:2526:35: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2526 |   smc_state->levels[i].stateFlags |=
      |                                   ^~
drivers/gpu/drm/radeon/ni_dpm.c:2526:35: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2526 |   smc_state->levels[i].stateFlags |=
      |   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~
 2527 |    ((i != (state->performance_level_count - 1)) && power_boost_limit) ?
      |    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 2528 |    PPSMC_STATEFLAG_POWERBOOST : 0;
      |    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/radeon/ni_dpm.c:2442:20: warning: array subscript 1 is above array bounds of ‘NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’ {aka ‘struct NISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
 2442 |   smc_state->levels[i + 1].aT = cpu_to_be32(a_t);

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109Build-tested-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/6023ed54.BfIY+9Uz81I6nq19%25lkp@intel.com/Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: Replace one-element array with flexible-array in struct _ATOM_Vega10_GFXCLK_Dependency_Table

There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

Use flexible-array member in struct _ATOM_Vega10_GFXCLK_Dependency_Table,
instead of one-element array.

Also, this helps with the ongoing efforts to enable -Warray-bounds and
fix the following warning:

drivers/gpu/drm/amd/amdgpu/../pm/powerplay/hwmgr/vega10_hwmgr.c: In function ‘vega10_get_pp_table_entry_callback_func’:
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/hwmgr/vega10_hwmgr.c:3113:30: warning: array subscript 4 is above array bounds of ‘ATOM_Vega10_GFXCLK_Dependency_Record[1]’ {aka ‘struct _ATOM_Vega10_GFXCLK_Dependency_Record[1]’} [-Warray-bounds]
 3113 |     gfxclk_dep_table->entries[4].ulClk;
      |     ~~~~~~~~~~~~~~~~~~~~~~~~~^~~

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109Build-tested-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/6023ff3d.WY3sSCkGRQPdPlVo%25lkp@intel.com/Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

Refactor the code according to the use of a flexible-array member in
struct SISLANDS_SMC_SWSTATE, instead of a one-element array, and use
the struct_size() helper to calculate the size for the allocation.

Also, this helps with the ongoing efforts to enable -Warray-bounds and
fix the following warnings:

drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:2448:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:2449:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:2450:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:2451:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:2452:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/si_dpm.c:5570:20: warning: array
subscript 1 is above array bounds of ‘SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’
{aka ‘struct SISLANDS_SMC_HW_PERFORMANCE_LEVEL[1]’} [-Warray-bounds]

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109Build-tested-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/6023be58.sk66L%2FV4vuSJI5mI%25lkp@intel.com/Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There are spelling mistakes in error and warning messages, the text
power_dpm_force_perfomance_level is missing a letter r and should be
power_dpm_force_performance_level.  Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use debugfs API directly instead of drm middle layer.

This also includes following debugfs file output changes:
1 amdgpu_evict_vram/amdgpu_evict_gtt output will not contain any braces.
  e.g. (0) --> 0
2 amdgpu_gpu_recover output will print return value of
  amdgpu_device_gpu_recover() instead of not so important "gpu recover"
  message.

v2: * checkpatch.pl: use '0444' instead of S_IRUGO.
    * remove S_IFREG from mode.
    * remove mode variable.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use debugfs API directly instead of drm middle layer.

v2: * checkpatch.pl: use '0444' instead of S_IRUGO.
    * remove S_IFREG from mode.
    * remove mode variable.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use debugfs API directly instead of drm middle layer.

v2: * checkpatch.pl: use '0444' instead of S_IRUGO.
    * remove S_IFREG from mode.
    * remove mode variable.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Removed unused CONFIG_DRM_AMDGPU_GART_DEBUGFS code.
We can use umr instead of this gart debugfs.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove unnecessary debugfs dentries and also radeon_ttm_debugfs_fini()
as drm_debugfs_cleanup() will recursively remove debugfs files.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Cleanup unnecessary debugfs dentries and surrounding functions.

v3: remove return value check for debugfs_create_file()
v2: remove ttm_debugfs_entries array.
    do not init variables.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes the rlc reference clock used for GPU timestamps.
Value is 100Mhz.  Confirmed with hardware team.

v2: reword commit message.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1480Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Disable it on those boards.  No functional change, this just
removes the message about VCE failing to initialize.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=197327Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

memalloc_nofs_save/restore are no longer sufficient to prevent recursive
lock warnings when holding locks that can be taken in MMU notifiers. Use
memalloc_noreclaim_save/restore instead.

Fixes: f920e413 ("mm: track mmu notifiers in fs_reclaim_acquire/release")
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

dcn21_validate_bandwidth() calls functions that use floating point math.
On my machine this sometimes results in simd exceptions when there are
other FPU users such as KVM virtual machines running. The screen freezes
completely in this case.

Wrapping the function with DC_FP_START()/DC_FP_END() seems to solve the
problem. This mirrors the approach used for dcn20_validate_bandwidth.

Tested on a AMD Ryzen 7 PRO 4750U (Renoir).

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206987Signed-off-by: Jan Kokemüller <jan.kokemueller@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fix potential integer overflow by casting actual_calculated_clock_100hz
to u64, in order to give the compiler complete information about the
proper arithmetic to use.

Notice that such variable is used in a context that expects
an expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:

actual_calculated_clock_100hz * post_divider

Fixes: 7a03fdf6 ("drm/amd/display: fix 64bit division issue on 32bit OS")
Addresses-Coverity-ID: 1501691 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes: 9037246b ("drm/amd/display: Add sysfs interface for set/get srm")
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This fixes incorrect TCC harvesting info reported to userspace.
The impact was a very very tiny performance degradation (unnecessary
GL2 cache flushes).
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fix the following coccicheck warning:

./drivers/gpu/drm/radeon/rs690.c:190:6-35: WARNING: Comparison to bool.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the following coccicheck warning:

./drivers/gpu/drm/amd/display/dc/inc/hw/clk_mgr_internal.h:319:11-23:
WARNING: Comparison to bool.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit 4a3dea89.

This causes blank screens for some users.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1388
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Remove NULL checks before vfree() to fix these warnings:
drivers/gpu/drm/amd/amdgpu/amdgpu_cs.c:102:2-8: WARNING: NULL
check before some freeing functions is not needed.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch is to make the error log more clear for fine grain tuning
function, it covers Raven/Raven2/Picasso/Renoir/Vangogh.
The fine grain tuning function uses the sysfs file -- pp_od_clk_voltage,
but only when another sysfs file -- power_dpm_force_performance_level is
switched to "manual" mode, it is allowed to access "pp_od_clk_voltage".
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Extend retry times of KIQ to avoid starvation situation caused by
long time full access of GPU by other VFs.
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This version brings along following fixes:
- Fix error handling in dc/dcn10/dcn10_hw_sequencer_debug.c
- DIO Supported for virtual displays
- memset dmub_rb_cmd to 0 which fixes issues talking with firmware
- fix 64bit division issue on 32bit OS
- move edp sink present detection to hw init to fix hang
- reverts a patch that caused 3x4K60 displays over MST
  with DSC enabled to not light up
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add new definition and union for dmub_rb_cmd_dig1_transmitter_control
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It is possible for ret_vsnprintf to be assigned negative value in
error cases. As an unsigned variable, negative values which
are stored in their 2's complement form gets treated as a positive
number. This will led to treating bad cases as good ones.
eg: -1 gets stored as 0xFFFFFFFF on a 32 bit system
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Virtual displays do not use the backend of the pipe, and so have
infinite backend bandwidth.

[HOW]
Add a skip_dio_check bool to the VBA struct, which is used to override
the DIOSupport calculations.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Chris Park <Chris.Park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Since dmub_rb_cmds are not initialized to 0,
the header is filled with invalid data.
This is causing issues on the fw side.

[How]
Initialize dmub_rb_cmd unions to 0.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Replace "/" with div_u64 for 64bit division on 32bit OS.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
At SW init, we may not be ready to do detect eDP sink.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>