This patch enables adc engine at initialization time and waits
for the initial sequence completion before enabling adc channels.

Without this code adc channels are not functional and shows
zeros for all connected channels.

Tested on mellanox msn platform.

v1 -> v2:
Pointed by Rick Altherr:
 - Wait init sequence code enabled by bool
from OF match table.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

After probe we would put the device in normal mode, after a runtime
suspend-resume we would put it back in normal mode. But for a regular
suspend-resume we would only put it back in normal mode if triggers
or events have been requested.  This is not consistent and breaks
reading raw values after a suspend-resume.

This commit changes the regular resume path to also unconditionally put
the device back in normal mode, fixing reading of raw values not working
after a regular suspend-resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

gcc-7 points out an older regression:

drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw':
drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]

The original code had 'unsigned short' here, but incorrectly got
converted to 'bool'. This reverts the regression and uses a normal
type instead.

Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

I noticed in its DSDT that one of my tablets actually is using the GPADC
pin for temperature monitoring.

The whole axp288_adc_set_ts() function is a bit weird, in the past it was
removed because it seems to make no sense, then this was reverted because
of regressions.

So I decided to test the special GPADC pin handling on this tablet.
Conclusion: not only is axp288_adc_set_ts() necessary, we need to sleep a
bit after making the AXP288_ADC_TS_PIN_CTRL changes before sampling the
GPADC, otherwise it will often (about 80% of the time) read 0 instead of
its actual value.

It seems that there is only 1 bias current source and to be able to use it
for the GPIO0 pin in GPADC mode it must be temporarily turned off for the
TS pin, but the datasheet does not mention this.

This commit adds a sleep after disabling the TS pin bias current,
fixing the GPADC more often then not wrongly returning 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].

[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf

Fixes: a7754276 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration

Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.

Fixes: ddc05fa2 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.

So lets go back to hard coding the values, this reverts
commit fa2849e9 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.

The exact cause is not fully understood, hence the revert to a known working
state.

Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).

When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).

Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.

Fixes: d1caa990 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Set multiread variable to false for LPS22HB pressure sensor since
it is already enabled in CTRL_REG2. Previous configuration does not
cause any issue in I2C communication since SUB Msb has no meaning
whereas it breaks register address in SPI communication

Fixes: e039e2f5 (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two.  The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.

This is going to change userspace ABI.  Hopefully fixing this to be
what it should always have been won't break any userspace code.

Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.

This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.

Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.

One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications.  For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).

Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.

Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "Stream of fixes has slowed down, only a few this week:

   - Some DT fixes for Allwinner platforms, and addition of a clock to
     the R_CCU clock controller that had been missed.

   - A couple of small DT fixes for am335x-sl50"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU

Merge tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes

Allwinner fixes for 4.12

A few fixes around the PRCM support that got in 4.12 with a wrong
compatible, and a missing clock in the binding.

* tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.12/fixes-sl50' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two fixes for am335x-sl50 to fix a boot time error
for claiming SPI pins, and to fix a SDIO card detect
pin for production version of the device.

* tag 'omap-for-v4.12/fixes-sl50' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull virtio bugfix from Michael Tsirkin:
 "It turns out balloon does not handle IOMMUs correctly. We should fix
  that at some point, for now let's just disable this configuration"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: disable VIOMMU support

Pull i2c fixes from Wolfram Sang:
 "Two driver bugfixes"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: fix wrong device address when unmap the data buffer
  i2c: rcar: use correct length when unmapping DMA

Pull MIPS fixes from Ralf Baechle:

 - Three highmem fixes:
    + Fixed mapping initialization
    + Adjust the pkmap location
    + Ensure we use at most one page for PTEs

 - Fix makefile dependencies for .its targets to depend on vmlinux

 - Fix reversed condition in BNEZC and JIALC software branch emulation

 - Only flush initialized flush_insn_slot to avoid NULL pointer
   dereference

 - perf: Remove incorrect odd/even counter handling for I6400

 - ftrace: Fix init functions tracing

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: .its targets depend on vmlinux
  MIPS: Fix bnezc/jialc return address calculation
  MIPS: kprobes: flush_insn_slot should flush only if probe initialised
  MIPS: ftrace: fix init functions tracing
  MIPS: mm: adjust PKMAP location
  MIPS: highmem: ensure that we don't use more than one page for PTEs
  MIPS: mm: fixed mappings: correct initialisation
  MIPS: perf: Remove incorrect odd/even counter handling for I6400

virtio balloon bypasses the DMA API entirely so does not support the
VIOMMU right now.  It's not clear we need that support, for now let's
just make sure we don't pretend to support it.

Cc: stable@vger.kernel.org
Cc: Wei Wang <wei.w.wang@intel.com>
Fixes: 1a937693 ("virtio: new feature to detect IOMMU device quirk")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Pull x86 fixes from Thomas Gleixner:
 "Two fixlets for x86:

   - Handle WARN_ONs proper with the new UD based WARN implementation

   - Disable 1G mappings when 2M mappings are disabled by kmemleak or
     debug_pagealloc. Otherwise 1G mappings might still be used,
     confusing the debug mechanisms"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
  x86/debug: Handle early WARN_ONs proper

Pull timer fixes from Thomas Gleixner:
 "Three fixlets for timers:

   - Two hot-fixes for the alarmtimer based posix timers, which prevent
     a nasty DOS by self rescheduling timers. The proper cleanup of that
     mess is queued for 4.13

   - Make a function static"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Make tick_broadcast_setup_oneshot() static
  alarmtimer: Rate limit periodic intervals
  alarmtimer: Prevent overflow of relative timers

Pull scheduler fixes from Thomas Gleixner:
 "Two small fixes for the schedulre core:

   - Use the proper switch_mm() variant in idle_task_exit() because that
     code is not called with interrupts disabled.

   - Fix a confusing typo in a printk"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
  sched/fair: Fix typo in printk message

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the perf user space side:

   - Fix the probing of precise_ip level, which got broken recently for
     x86.

   - Unbreak the ARCH=x86_64 build

   - Report module before trying to unwind into the module code, which
     avoids broken stack frames displayed"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf unwind: Report module before querying isactivation in dwfl unwind
  perf tools: Fix build with ARCH=x86_64
  perf evsel: Fix probing of precise_ip level for default cycles event

Pull irq fix from Thomas Gleixner:
 "Add a missing resource release to an error path"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Release resources in __setup_irq() error path

Pull objtool fix from Thomas Gleixner:
 "A single fix which adds fortify_panic to the list of no return
  functions"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Add fortify_panic as __noreturn function

Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:
 "Two LED fixes:

   - fix signal source assignment for leds-bcm6328

   - revert patch that intended to fix LED behavior on suspend but it
     had a side effect preventing suspend at all due to uevent being
     sent on trigger removal"

* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  Revert "leds: handle suspend/resume in heartbeat trigger"
  leds: bcm6328: fix signal source assignment for leds 4 to 7

Pull USB fixes from Greg KH:
 "Here are some small gadget and xhci USB fixes for 4.12-rc6.

  Nothing major, but one of the gadget patches does fix a reported oops,
  and the xhci ones resolve reported problems. All have been in
  linux-next with no reported issues"

* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
  usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
  usb: xhci: Fix USB 3.1 supported protocol parsing
  USB: gadget: fix GPF in gadgetfs
  usb: gadget: composite: make sure to reactivate function on unbind

Pull staging and IIO fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 4.12-rc6.

  Nothing huge, just a few small driver fixes for reported issues. All
  have been in linux-next with no reported issues"

* tag 'staging-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Staging: rtl8723bs: fix an error code in isFileReadable()
  iio: buffer-dmaengine: Add missing header buffer_impl.h
  iio: buffer-dma: Add missing header buffer_impl.h
  iio: adc: meson-saradc: fix potential crash in meson_sar_adc_clear_fifo
  iio: adc: mxs-lradc: Fix return value check in mxs_lradc_adc_probe()
  iio: imu: inv_mpu6050: add accel lpf setting for chip >= MPU6500
  staging: iio: ad7152: Fix deadlock in ad7152_write_raw_samp_freq()

Pull ceph fixes from Ilya Dryomov:
 "A fix for an old ceph ->fh_to_* bug from Luis and two timestamp fixups
  from Zheng, prompted by the ongoing y2038 work"

* tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client:
  ceph: unify inode i_ctime update
  ceph: use current_kernel_time() to get request time stamp
  ceph: check i_nlink while converting a file handle to dentry

Pull xfs fix from Darrick Wong:
 "One more bugfix for you for 4.12-rc6 to fix something that came up in
  an earlier rc:

   - Fix some bogus ASSERT failures on CONFIG_SMP=n and CONFIG_XFS_DEBUG=y"

* tag 'xfs-4.12-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix spurious spin_is_locked() assert failures on non-smp kernels

Pull ufs fixes from Al Viro:
 "Fix assorted ufs bugs: a couple of deadlocks, fs corruption in
  truncate(), oopsen on tail unpacking and truncate when racing with
  vmscan, mild fs corruption (free blocks stats summary buggered, *BSD
  fsck would complain and fix), several instances of broken logics
  around reserved blocks (starting with "check almost never triggers
  when it should" and then there are issues with sufficiently large
  UFS2)"

[ Note: ufs hasn't gotten any loving in a long time, because nobody
  really seems to use it. These ufs fixes are triggered by people
  actually caring now, not some sudden influx of new bugs.  - Linus ]

* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ufs_truncate_blocks(): fix the case when size is in the last direct block
  ufs: more deadlock prevention on tail unpacking
  ufs: avoid grabbing ->truncate_mutex if possible
  ufs_get_locked_page(): make sure we have buffer_heads
  ufs: fix s_size/s_dsize users
  ufs: fix reserved blocks check
  ufs: make ufs_freespace() return signed
  ufs: fix logics in "ufs: make fsck -f happy"

Pull vfs fixes from Al Viro:
 "A couple of fixes; a leak in mntns_install() caught by Andrei (this
  cycle regression) + d_invalidate() softlockup fix - that had been
  reported by a bunch of people lately, but the problem is pretty old"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: don't forget to put old mntns in mntns_install
  Hang/soft lockup in d_invalidate with simultaneous calls

Pull PCI fixes from Bjorn Helgaas:

 - fix another PCI_ENDPOINT build error (merged for v4.12)

 - fix error codes added to config accessors for v4.12

* tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: endpoint: Select CRC32 to fix test build error
  PCI: Make error code types consistent in pci_{read,write}_config_*

Pull fbdev fixes from Bartlomiej Zolnierkiewicz:

 - fix udlfb driver to stop spamming logs (Mike Gerow)

 - add missing endianness conversions in smscufx & udlfb drivers (Johan
   Hovold)

 - fix few gcc warnings/errors (Arnd Bergmann)

* tag 'fbdev-v4.12-rc6' of git://github.com/bzolnier/linux:
  video: fbdev: udlfb: drop log level for blanking
  video: fbdev: via: remove possibly unused variables
  video: fbdev: add missing USB-descriptor endianness conversions
  video: fbdev: avoid int-in-bool-context warning

Merge misc fixes from Andrew Morton:
 "5 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: correct the comment when reclaimed pages exceed the scanned pages
  userfaultfd: shmem: handle coredumping in handle_userfault()
  mm: numa: avoid waiting on freed migrated pages
  swap: cond_resched in swap_cgroup_prepare()
  mm/memory-failure.c: use compound_head() flags for huge pages

Commit e1587a49 ("mm: vmpressure: fix sending wrong events on
underflow") declared that reclaimed pages exceed the scanned pages due
to the thp reclaim.

That is incorrect because THP will be spilt to normal page and loop
again, which will result in the scanned pages increment.

[akpm@linux-foundation.org: tweak comment text]
Link: http://lkml.kernel.org/r/1496824266-25235-1-git-send-email-zhongjiang@huawei.comSigned-off-by: zhongjiang <zhongjiang@huawei.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().

shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.

This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.

The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits.  Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).

It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).

Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.comSigned-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>	[4.11+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry.  However,
we can race with migrate_misplaced_transhuge_page():

    // do_huge_pmd_numa_page                // migrate_misplaced_transhuge_page()
    // Holds 0 refs on page                 // Holds 2 refs on page

    vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
    /* ... */
    if (pmd_trans_migrating(*vmf->pmd)) {
            page = pmd_page(*vmf->pmd);
            spin_unlock(vmf->ptl);
                                            ptl = pmd_lock(mm, pmd);
                                            if (page_count(page) != 2)) {
                                                    /* roll back */
                                            }
                                            /* ... */
                                            mlock_migrate_page(new_page, page);
                                            /* ... */
                                            spin_unlock(ptl);
                                            put_page(page);
                                            put_page(page); // page freed here
            wait_on_page_locked(page);
            goto out;
    }

This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions.  This has been observed on arm64 KVM guests.

We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().

When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.

Fixes: b8916634 ("mm: Prevent parallel splits during THP migration")
Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.comSigned-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I saw need_resched() warnings when swapping on large swapfile (TBs)
because continuously allocating many pages in swap_cgroup_prepare() took
too long.

We already cond_resched when freeing page in swap_cgroup_swapoff().  Do
the same for the page allocation.

Link: http://lkml.kernel.org/r/20170604200109.17606-1-yuzhao@google.comSigned-off-by: Yu Zhao <yuzhao@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory_failure() chooses a recovery action function based on the page
flags.  For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:

> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed

Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead.  This results in the me_huge_page() recovery
action being called:

> Memory failure: 0x9b7969: recovery action for huge page: Delayed

For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.

Fixes: 524fca1e ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages")
Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.comSigned-off-by: James Morse <james.morse@arm.com>
Tested-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>