- 22 Feb, 2012 10 commits
-
-
Chris Boot authored
The firewire-sbp2 module tries to login to an SBP-2/3 target even when it is running on the local node, which fails because of the inability to fetch data from DMA mapped regions using firewire transactions on the local node. It also doesn't make much sense to have the initiator and target on the same node, so this patch prevents this behaviour. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changed the comment)
-
Chris Boot authored
If the target's unit directory contains a Unit_Unique_ID entry, we should use that as the target's GUID for identification purposes. The SBP-2 standards document says: "Although the node unique ID (EUI-64) present in the bus information block is sufficient to uniquely identify nodes attached to Serial Bus, it is insufficient to identify a target when a vendor implements a device with multiple Serial Bus node connections. In this case initiator software requires information by which a particular target may be uniquely identified, regardless of the Serial Bus access path used." [ IEEE T10 P1155D Revision 4, Section 7.6 (page 51) ] and [ IEEE T10 P1467D Revision 5, Section 7.9 (page 74) ] Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
santosh nayak authored
Use the macro DMA_BIT_MASK instead of the constant 0xffffffff Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
fw_core_handle_request() is called by the low-level driver in tasklet context or process context, and fw_core_add/remove_address_handler() is called by mid- or high-level code in process context. So convert address_handler_lock accesses from those which disable local IRQs to ones which just disable local softIRQs. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Fix the following unlikely but possible race: CPU 1 CPU 2 ------------------------------------------------------------------------ AR-request tasklet lookup handler unregister handler free handler->callback_data or handler call handler->callback The application which registered the handler has no way to stop nodes sending new requests to their address range, hence cannot prevent this race. Fix it simply by extending the address_handler_lock-protected region from only around the lookup to around both lookup and call. We only need to do so in the exclusive region handler; the FCP region handler already holds the lock around the handler->callback call. Alas this removes the current ability to execute the callback in parallel on different CPUs if it was called for different FireWire cards at the same time. (For a single card, the handler is already serialized.) If this loss of a rather obscure feature is not tolerable, a more complex fix would be required: Add a handler reference counter; wait in fw_core_remove_address_handler() for this conter to become zero. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Target-like applications or peer-to-peer-like applications require the global address handler registration which we have right now, or a per- card registration. And node lookup, while it would be nice to have, would be impossible in the brief time between self-ID-complete event and completion of firewire-core's topology scanning. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Associate all log messages from firewire-core with the respective card because some people have more than one card. E.g. firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0 firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0 firewire_core: created device fw0: GUID 0814438400000389, S800 firewire_core: phy config: new root=ffc1, gap_count=5 firewire_core: created device fw1: GUID 0814438400000388, S800 firewire_core: created device fw2: GUID 0001d202e06800d1, S800 turns into firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0 firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0 firewire_core 0000:04:00.0: created device fw0: GUID 0814438400000389, S800 firewire_core 0000:04:00.0: phy config: new root=ffc1, gap_count=5 firewire_core 0000:05:00.0: created device fw1: GUID 0814438400000388, S800 firewire_core 0000:04:00.0: created device fw2: GUID 0001d202e06800d1, S800 This increases the module size slightly; to keep this in check, turn the former printk wrapper macros into functions. Their implementation is largely copied from driver core's dev_printk counterparts. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Change the log line prefix from "firewire_net: " to "net firewire0: " etc. for the case that several RFC 2734 interfaces are being used in the same machine. Note, the netdev_printk API is not very useful to firewire-net. netdev_notice(net, "abc\n") would result in irritating messages like "firewire_ohci 0000:0a:00.0: firewire0: abc". Nor would a dev_printk on the fw_unit.device to which firewire-net is being bound be useful, because there are generally multiple ones of those per interface (from all RFC 2734 peers on the bus, the local node being only one of them). In the initialization message of each interface, log the PCI device name of the card which is parent of the netdevice instead of the GUID of the peer which was semi-randomly used to establish the netdevice. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
On second thought, there is little reason to have driver name differ from module name. Therefore, change /sys/bus/firewire/drivers/net /sys/bus/firewire/devices/fw0.0/driver -> [...]/net /sys/module/firewire_net/drivers/firewire:net to /sys/bus/firewire/drivers/firewire_net /sys/bus/firewire/devices/fw0.0/driver -> [...]/firewire_net /sys/module/firewire_net/drivers/firewire:firewire_net It is redundant but consistent with firewire-sbp2's recently changed driver name. I don't see this anywhere used, so it should not matter either way. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Commit eba9ebaa "firewire: sbp2: use dev_printk API" changed messages from e.g. firewire_sbp2: fw3.0: logged in to LUN 0000 (0 retries) to sbp2 fw3.0: logged in to LUN 0000 (0 retries) because the driver calls itself as "sbp2" when registering with driver core and with SCSI core. This is of course confusing, so switch to the name "firewire_sbp2" for driver core in order to match what lsmod and /sys/module/ show. So we are back to firewire_sbp2 fw3.0: logged in to LUN 0000 (0 retries) in the kernel log. This also changes /sys/bus/firewire/drivers/sbp2 /sys/bus/firewire/devices/fw3.0/driver -> [...]/sbp2 /sys/module/firewire_sbp2/drivers/firewire:sbp2 to /sys/bus/firewire/drivers/firewire_sbp2 /sys/bus/firewire/devices/fw3.0/driver -> [...]/firewire_sbp2 /sys/module/firewire_sbp2/drivers/firewire:firewire_sbp2 but "cat /sys/class/scsi_host/host27/proc_name" stays "sbp2" just in case that proc_name is used by any userland. The transport detection in lsscsi is not affected. (Tested with lsscsi version 0.25.) Udev's /dev/disk/by-id and by-path symlinks are not affected either. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
- 15 Jan, 2012 3 commits
-
-
Stefan Richter authored
All messages are uniformly prefixed by driver name and device name now. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
All messages are uniformly prefixed by driver name and device name now. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
fw_unit device drivers invariably need to talk to the fw_unit's parent (an fw_device) and grandparent (an fw_card). firewire-core already maintains an fw_card reference for the entire lifetime of an fw_device. Likewise, let firewire-core maintain an fw_device reference for the entire lifetime of an fw_unit so that fw_unit drivers don't have to. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
- 25 Dec, 2011 1 commit
-
-
Stefan Richter authored
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
- 18 Oct, 2011 2 commits
-
-
Clemens Ladisch authored
Add the dma_sync_single_* calls necessary to ensure proper cache synchronization for isochronous data buffers on non-coherent architectures. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Clemens Ladisch authored
If a device's firmware initiates a bus reset by setting the IBR bit in PHY register 1 without resetting the gap count field to 63 (and without having sent a PHY configuration packet beforehand), the gap count of this node will remain at the old value after the bus reset and thus be inconsistent with the gap count on all other nodes. The bus manager is supposed to detect the inconsistent gap count values in the self ID packets and correct them by issuing another bus reset. However, if the buggy device happens to be the cycle master, and if it sends a cycle start packet immediately after the bus reset (which is likely after a long bus reset), then the time between the end of the selfID phase and the start of the cycle start packet will be based on the too-small gap count value, so this gap will be too short to be detected as a subaction gap by the other nodes. This means that the cycle start packet will be assumed to be self ID data, and will be stored after the actual self ID quadlets in the self ID buffer. This garbage in the self ID buffer made firewire-core ignore all of the self ID data, and thus prevented the Linux bus manager from correcting the problem. Furthermore, because the bus reset handling was aborted completely, asynchronous transfers would be no longer handled correctly, and fw_run_transaction() would hang until the next bus reset. To fix this, make the detection of inconsistent self IDs more discriminating: If the invalid data in the self ID buffer looks like a cycle start packet, we can assume that the previous data in the buffer is correctly received self ID information, and process it normally. (We inspect only the first quadlet of the cycle start packet, because this value is different enough from any valid self ID quadlet, and many controllers do not store the cycle start packet in five quadlets because they expect self ID data to have an even number of quadlets.) This bug has been observed when a bus-powered DesktopKonnekt6 is switched off with its power button. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
- 09 Oct, 2011 4 commits
-
-
Stephan Gatzka authored
Change memory region to ohci "middle address space". This effectively reduces the number of packets by 50%. [Stefan R.:] This eliminates 1394 ack packets and improved throughput by a few percent in some tests with an S400a connection with and without gap count optimization. Since firewire-net taxes the AR-req DMA unit of a FireWire controller much more than firewire-sbp2 (which uses the middle address space with PCI posted writes too), this commit also changes a related error printk into a ratelimited one as a precaution. Side note: The IPv4-over-1394 drivers of Mac OS X 10.4, Windows XP SP3, and the Thesycon 1394 bus driver for Windows all use the middle address space too. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Use kernel.h's convenience macros. Also omit a printk that should never happen and won't matter much if it ever happened. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Takes less source code and machine code, and less runtime with PHYs other than TSB41BA3D (e.g. TSB81BA3 with device ID 0x831304 which takes one instead of six read_paged_phy_reg now). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Fix: phy_reg_mutex must be held over the write/read_phy_reg pair which gets PHY port status. Only print to the log when a TSB41BA3D was found. By far most TSB82AA2 cards have a TSB81BA3, and firewire-ohci can keep quiet about that. Shorten some strings and comments. Change some whitespace. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
- 16 Sep, 2011 6 commits
-
-
Stephan Gatzka authored
This patch implements a work around for the Texas Instruments PHY TSB41BA3D. This phy has a bug at least in combination with the TI LLCs TSB82AA2B and TSB12LV26. The selfid coming from the locally connected phy is not propagated into the selfid buffer of the OHCI (see http://www.ti.com/litv/pdf/sllz059 for details). The main idea is to construct the selfid ourselves. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stephan Gatzka authored
Code inside bus_reset_work may now sleep. This is a prerequisite to support a phy from Texas Instruments cleanly. The patch to support this phy will be submitted later. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
sbp2_release_target() is folded into its primary user, sbp2_remove(). The only other caller, a failure path in sbp2_probe(), now uses sbp2_remove(). This adds unnecessary cancel_delayed_work_sync() calls to that failure path but results in less code and text. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Implement sbp2_queue_work(), which is now a very simple accessor to one of the struct sbp2_logical_unit members, right after the definition of struct sbp2_logical_unit. Put the sbp2_reconnect() implementation right after the sbp2_login() implementation. They are both part of the SBP-2 access protocol. Implement the driver methods sbp2_probe(), spp2_update(), sbp2_remove() in this order, reflecting the lifetime of an SBP-2 target. Place the sbp2_release_target() implementation right next to sbp2_remove() which is its primary user, and after sbp2_probe() which is the counterpart to sbp2_release_target(). There are no changes to the implementations here, or at least not meant to be. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Since commit 0278ccd9 "firewire: sbp2: fix panic after rmmod with slow targets", the lifetime of an sbp2_target instance does no longer extent past the return of sbp2_remove(). Therefore it is no longer necessary to call fw_unit_get/put() and fw_device_get/put() in sbp2_probe/remove(). Furthermore, said commit also ensures that lu->work is not going to be executed or requeued at a time when the sbp2_target is no longer in use. Hence there is no need for sbp2_target reference counting for lu->work. Other concurrent contexts: - Processes which access the sysfs of the SCSI host device or of one of its subdevices are safe because these interfaces are all removed by scsi_remove_device/host() in sbp2_release_target(). - SBP-2 command block ORB transactions are finished when scsi_remove_device() in sbp2_release_target() returns. - SBP-2 management ORB transactions are finished when cancel_delayed_work_sync(&lu->work) before sbp2_release_target() returns. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Ming Lei authored
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 . An O2Micro PCI Express FireWire controller, "FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)" which is a combination device together with an SDHCI controller and some sort of storage controller, misses SBP-2 status writes from an attached FireWire HDD. This problem goes away if MSI is disabled for this FireWire controller. The device reportedly does not require QUIRK_CYCLE_TIMER. Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog) Cc: <stable@kernel.org>
-
- 12 Sep, 2011 9 commits
-
-
Linus Torvalds authored
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm: Remove duplicate "return" statement drm/nv04/crtc: Bail out if FB is not bound to crtc drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate drm/nouveau: fix oops on pre-semaphore hardware drm/nv50/crtc: Bail out if FB is not bound to crtc drm/radeon/kms: fix DP detect and EDID fetch for DP bridges
-
git://git.linaro.org/people/arnd/arm-socLinus Torvalds authored
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc: ARM: CSR: add missing sentinels to of_device_id tables ARM: cns3xxx: Fix newly introduced warnings in the PCIe code ARM: cns3xxx: Fix compile error caused by hardware.h removed ARM: davinci: fix cache flush build error ARM: davinci: correct MDSTAT_STATE_MASK ARM: davinci: da850 EVM: read mac address from SPI flash OMAP: omap_device: fix !CONFIG_SUSPEND case in _noirq handlers OMAP2430: hwmod: musb: add missing terminator to omap2430_usbhsotg_addrs[] OMAP3: clock: indicate that gpt12_fck and wdt1_fck are in the WKUP clockdomain OMAP4: clock: fix compile warning OMAP4: clock: re-enable previous clockdomain enable/disable sequence OMAP: clockdomain: Wait for powerdomain to be ON when using clockdomain force wakeup OMAP: powerdomains: Make all powerdomain target states as ON at init
-
Mathieu Desnoyers authored
The LTTng 2.0 kernel tracer (stand-alone module package, available at http://lttng.org) uses the 0xF6 ioctl range for tracer control and transport operations. Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/chrismason/linuxLinus Torvalds authored
* 'for-linus' of git://github.com/chrismason/linux: Btrfs: add dummy extent if dst offset excceeds file end in Btrfs: calc file extent num_bytes correctly in file clone btrfs: xattr: fix attribute removal Btrfs: fix wrong nbytes information of the inode Btrfs: fix the file extent gap when doing direct IO Btrfs: fix unclosed transaction handle in btrfs_cont_expand Btrfs: fix misuse of trans block rsv Btrfs: reset to appropriate block rsv after orphan operations Btrfs: skip locking if searching the commit root in csum lookup btrfs: fix warning in iput for bad-inode Btrfs: fix an oops when deleting snapshots
-
Miklos Szeredi authored
kmemleak is reporting that 32 bytes are being leaked by FUSE: unreferenced object 0xe373b270 (size 32): comm "fusermount", pid 1207, jiffies 4294707026 (age 2675.187s) hex dump (first 32 bytes): 01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<b05517d7>] kmemleak_alloc+0x27/0x50 [<b0196435>] kmem_cache_alloc+0xc5/0x180 [<b02455be>] fuse_alloc_forget+0x1e/0x20 [<b0245670>] fuse_alloc_inode+0xb0/0xd0 [<b01b1a8c>] alloc_inode+0x1c/0x80 [<b01b290f>] iget5_locked+0x8f/0x1a0 [<b0246022>] fuse_iget+0x72/0x1a0 [<b02461da>] fuse_get_root_inode+0x8a/0x90 [<b02465cf>] fuse_fill_super+0x3ef/0x590 [<b019e56f>] mount_nodev+0x3f/0x90 [<b0244e95>] fuse_mount+0x15/0x20 [<b019d1bc>] mount_fs+0x1c/0xc0 [<b01b5811>] vfs_kern_mount+0x41/0x90 [<b01b5af9>] do_kern_mount+0x39/0xd0 [<b01b7585>] do_mount+0x2e5/0x660 [<b01b7966>] sys_mount+0x66/0xa0 This leak report is consistent and happens once per boot on 3.1.0-rc5-dirty. This happens if a FORGET request is queued after the fuse device was released. Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Miklos Szeredi authored
Commit 37fb3a30 ("fuse: fix flock") added in 3.1-rc4 caused flock() to fail with ENOSYS with the kernel ABI version 7.16 or earlier. Fix by falling back to testing FUSE_POSIX_LOCKS for ABI versions 7.16 and earlier. Reported-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Tested-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
-
Arnd Bergmann authored
-
- 11 Sep, 2011 5 commits
-
-
git://linuxtv.org/mchehab/for_linusLinus Torvalds authored
* 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus: [media] vp7045: fix buffer setup [media] nuvoton-cir: simplify raw IR sample handling [media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL [media] v4l2: Fix documentation of the codec device controls [media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240 [media] gspca - sonixj: Fix wrong register mask for sensor om6802 [media] gspca - ov519: Fix LED inversion of some ov519 webcams [media] pwc: precedence bug in pwc_init_controls()
-
git://openrisc.net/~jonas/linuxLinus Torvalds authored
* 'for-linus' of git://openrisc.net/~jonas/linux: Add missing DMA ops openrisc: don't use pt_regs in struct sigcontext
-
Li Zefan authored
You can see there's no file extent with range [0, 4096]. Check this by btrfsck: # btrfsck /dev/sda7 root 5 inode 258 errors 100 ... Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
-
Li Zefan authored
num_bytes should be 4096 not 12288. Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
-
David Sterba authored
An attribute is not removed by 'setfattr -x attr file' and remains visible in attr list. This makes xfstests/062 pass again. Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <chris.mason@oracle.com>
-