- 01 Jun, 2016 27 commits
-
-
Marc Zyngier authored
commit 7c9b9730 upstream. The GICv3 driver wrongly assumes that it runs on the non-secure side of a secure-enabled system, while it could be on a system with a single security state, or a GICv3 with GICD_CTLR.DS set. Either way, it is important to configure this properly, or interrupts will simply not be delivered on this HW. Reported-by:
Peter Maydell <peter.maydell@linaro.org> Tested-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Will Deacon authored
commit f86c4fbd upstream. When an IPI is generated by a CPU, the pattern looks roughly like: <write shared data> smp_wmb(); <write to GIC to signal SGI> On the receiving CPU we rely on the fact that, once we've taken the interrupt, then the freshly written shared data must be visible to us. Put another way, the CPU isn't going to speculate taking an interrupt. Unfortunately, this assumption turns out to be broken. Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy to read some shared_data. Before CPUx has done anything, a random peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised. CPUy then takes the IRQ and starts executing the entry code, heading towards gic_handle_irq. Furthermore, let's assume that a bunch of the previous interrupts handled by CPUy were SGIs, so the branch predictor kicks in and speculates that irqnr will be <16 and we're likely to head into handle_IPI. The prefetcher then grabs a speculative copy of shared_data which contains a stale value. Meanwhile, CPUx gets round to updating shared_data and asking the GIC to send an SGI to CPUy. Internally, the GIC decides that the SGI is more important than the peripheral interrupt (which hasn't yet been ACKed) but doesn't need to do anything to CPUy, because the IRQ line is already raised. CPUy then reads the ACK register on the GIC, sees the SGI value which confirms the branch prediction and we end up with a stale shared_data value. This patch fixes the problem by adding an smp_rmb() to the IPI entry code in gic_handle_irq. As it turns out, the combination of a control dependency and an ISB instruction from the EOI in the GICv3 driver is enough to provide the ordering we need, so we add a comment there justifying the absence of an explicit smp_rmb(). Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Manfred Schlaegl authored
commit f49cf3b8 upstream. Pwm config may sleep so defer it using a worker. On a Freescale i.MX53 based board we ran into "BUG: scheduling while atomic" because input_inject_event locks interrupts, but imx_pwm_config_v2 sleeps. Tested on Freescale i.MX53 SoC with 4.6.0. Signed-off-by:
Manfred Schlaegl <manfred.schlaegl@gmx.at> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Roger Quadros authored
commit b49b927f upstream. We shouldn't be calling clk_prepare_enable()/clk_prepare_disable() in an atomic context. Fixes the following issue: [ 5.830970] ehci-omap: OMAP-EHCI Host Controller driver [ 5.830974] driver_register 'ehci-omap' [ 5.895849] driver_register 'wl1271_sdio' [ 5.896870] BUG: scheduling while atomic: udevd/994/0x00000002 [ 5.896876] 4 locks held by udevd/994: [ 5.896904] #0: (&dev->mutex){......}, at: [<c049597c>] __driver_attach+0x60/0xac [ 5.896923] #1: (&dev->mutex){......}, at: [<c049598c>] __driver_attach+0x70/0xac [ 5.896946] #2: (tll_lock){+.+...}, at: [<c04c2630>] omap_tll_enable+0x2c/0xd0 [ 5.896966] #3: (prepare_lock){+.+...}, at: [<c05ce9c8>] clk_prepare_lock+0x48/0xe0 [ 5.897042] Modules linked in: wlcore_sdio(+) ehci_omap(+) dwc3_omap snd_soc_ts3a225e leds_is31fl319x bq27xxx_battery_i2c tsc2007 bq27xxx_battery bq2429x_charger ina2xx tca8418_keypad as5013 leds_tca6507 twl6040_vibra gpio_twl6040 bmp085_i2c(+) palmas_gpadc usb3503 palmas_pwrbutton bmg160_i2c(+) bmp085 bma150(+) bmg160_core bmp280 input_polldev snd_soc_omap_mcbsp snd_soc_omap_mcpdm snd_soc_omap snd_pcm_dmaengine [ 5.897048] Preemption disabled at:[< (null)>] (null) [ 5.897051] [ 5.897059] CPU: 0 PID: 994 Comm: udevd Not tainted 4.6.0-rc5-letux+ #233 [ 5.897062] Hardware name: Generic OMAP5 (Flattened Device Tree) [ 5.897076] [<c010e714>] (unwind_backtrace) from [<c010af34>] (show_stack+0x10/0x14) [ 5.897087] [<c010af34>] (show_stack) from [<c040aa7c>] (dump_stack+0x88/0xc0) [ 5.897099] [<c040aa7c>] (dump_stack) from [<c020c558>] (__schedule_bug+0xac/0xd0) [ 5.897111] [<c020c558>] (__schedule_bug) from [<c06f3d44>] (__schedule+0x88/0x7e4) [ 5.897120] [<c06f3d44>] (__schedule) from [<c06f46d8>] (schedule+0x9c/0xc0) [ 5.897129] [<c06f46d8>] (schedule) from [<c06f4904>] (schedule_preempt_disabled+0x14/0x20) [ 5.897140] [<c06f4904>] (schedule_preempt_disabled) from [<c06f64e4>] (mutex_lock_nested+0x258/0x43c) [ 5.897150] [<c06f64e4>] (mutex_lock_nested) from [<c05ce9c8>] (clk_prepare_lock+0x48/0xe0) [ 5.897160] [<c05ce9c8>] (clk_prepare_lock) from [<c05d0e7c>] (clk_prepare+0x10/0x28) [ 5.897169] [<c05d0e7c>] (clk_prepare) from [<c04c2668>] (omap_tll_enable+0x64/0xd0) [ 5.897180] [<c04c2668>] (omap_tll_enable) from [<c04c1728>] (usbhs_runtime_resume+0x18/0x17c) [ 5.897192] [<c04c1728>] (usbhs_runtime_resume) from [<c049d404>] (pm_generic_runtime_resume+0x2c/0x40) [ 5.897202] [<c049d404>] (pm_generic_runtime_resume) from [<c049f180>] (__rpm_callback+0x38/0x68) [ 5.897210] [<c049f180>] (__rpm_callback) from [<c049f220>] (rpm_callback+0x70/0x88) [ 5.897218] [<c049f220>] (rpm_callback) from [<c04a0a00>] (rpm_resume+0x4ec/0x7ec) [ 5.897227] [<c04a0a00>] (rpm_resume) from [<c04a0f48>] (__pm_runtime_resume+0x4c/0x64) [ 5.897236] [<c04a0f48>] (__pm_runtime_resume) from [<c04958dc>] (driver_probe_device+0x30/0x70) [ 5.897246] [<c04958dc>] (driver_probe_device) from [<c04959a4>] (__driver_attach+0x88/0xac) [ 5.897256] [<c04959a4>] (__driver_attach) from [<c04940f8>] (bus_for_each_dev+0x50/0x84) [ 5.897267] [<c04940f8>] (bus_for_each_dev) from [<c0494e40>] (bus_add_driver+0xcc/0x1e4) [ 5.897276] [<c0494e40>] (bus_add_driver) from [<c0496914>] (driver_register+0xac/0xf4) [ 5.897286] [<c0496914>] (driver_register) from [<c01018e0>] (do_one_initcall+0x100/0x1b8) [ 5.897296] [<c01018e0>] (do_one_initcall) from [<c01c7a54>] (do_init_module+0x58/0x1c0) [ 5.897304] [<c01c7a54>] (do_init_module) from [<c01c8a3c>] (SyS_finit_module+0x88/0x90) [ 5.897313] [<c01c8a3c>] (SyS_finit_module) from [<c0107120>] (ret_fast_syscall+0x0/0x1c) [ 5.912697] ------------[ cut here ]------------ [ 5.912711] WARNING: CPU: 0 PID: 994 at kernel/sched/core.c:2996 _raw_spin_unlock+0x28/0x58 [ 5.912717] DEBUG_LOCKS_WARN_ON(val > preempt_count()) Reported-by:
H. Nikolaus Schaller <hns@goldelico.com> Tested-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Vik Heyndrickx authored
commit 20878232 upstream. Systems show a minimal load average of 0.00, 0.01, 0.05 even when they have no load at all. Uptime and /proc/loadavg on all systems with kernels released during the last five years up until kernel version 4.6-rc5, show a 5- and 15-minute minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on idle systems, but the way the kernel calculates this value prevents it from getting lower than the mentioned values. Likewise but not as obviously noticeable, a fully loaded system with no processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95 (multiplied by number of cores). Once the (old) load becomes 93 or higher, it mathematically can never get lower than 93, even when the active (load) remains 0 forever. This results in the strange 0.00, 0.01, 0.05 uptime values on idle systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05. It is not correct to add a 0.5 rounding (=1024/2048) here, since the result from this function is fed back into the next iteration again, so the result of that +0.5 rounding value then gets multiplied by (2048-2037), and then rounded again, so there is a virtual "ghost" load created, next to the old and active load terms. By changing the way the internally kept value is rounded, that internal value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon increasing load, the internally kept load value is rounded up, when the load is decreasing, the load value is rounded down. The modified code was tested on nohz=off and nohz kernels. It was tested on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was tested on single, dual, and octal cores system. It was tested on virtual hosts and bare hardware. No unwanted effects have been observed, and the problems that the patch intended to fix were indeed gone. Tested-by:
Damien Wyart <damien.wyart@free.fr> Signed-off-by:
Vik Heyndrickx <vik.heyndrickx@veribox.net> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Doug Smythies <dsmythies@telus.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 0f004f5a ("sched: Cure more NO_HZ load average woes") Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jaegeuk Kim authored
commit b5a7aef1 upstream. This patch allows fscrypto to handle a second key prefix given by filesystem. The main reason is to provide backward compatibility, since previously f2fs used "f2fs:" as a crypto prefix instead of "fscrypt:". Later, ext4 should also provide key_prefix() to give "ext4:". One concern decribed by Ted would be kinda double check overhead of prefixes. In x86, for example, validate_user_key consumes 8 ms after boot-up, which turns out derive_key_aes() consumed most of the time to load specific crypto module. After such the cold miss, it shows almost zero latencies, which treats as a negligible overhead. Note that request_key() detects wrong prefix in prior to derive_key_aes() even. Cc: Ted Tso <tytso@mit.edu> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Josh Poimboeuf authored
commit 4a6b27b7 upstream. Megha Dey reported a kernel panic in crypto code. The problem is that sha1_x8_avx2() clobbers registers r12-r15 without saving and restoring them. Before commit aec4d0e3 ("x86/asm/crypto: Simplify stack usage in sha-mb functions"), those registers were saved and restored by the callers of the function. I removed them with that commit because I didn't realize sha1_x8_avx2() clobbered them. Fix the potential undefined behavior associated with clobbering the registers and make the behavior less surprising by changing the registers to be callee saved/restored to conform with the C function call ABI. Also, rdx (aka RSP_SAVE) doesn't need to be saved: I verified that none of the callers rely on it being saved, and it's not a callee-saved register in the C ABI. Fixes: aec4d0e3 ("x86/asm/crypto: Simplify stack usage in sha-mb functions") Reported-by:
Megha Dey <megha.dey@linux.intel.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Andy Gross authored
commit 2a0974aa upstream. This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and ahb blocks. Without this flag, clk_set_rate can fail for certain frequency requests. Signed-off-by:
Andy Gross <andy.gross@linaro.org> Fixes: 3966fab8 ("clk: qcom: Add MSM8916 Global Clock Controller support") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Corentin LABBE authored
commit bdb6cf9f upstream. The current sun4i-ss driver could generate data corruption when ciphering/deciphering. It occurs randomly on end of handled data. No root cause have been found and the only way to remove it is to replace all spin_lock_bh by their irq counterparts. Fixes: 6298e948 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator") Signed-off-by:
LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by:
-
Horia Geant? authored
commit 3639ca84 upstream. Provide hardware state import/export functionality, as mandated by commit 8996eafd ("crypto: ahash - ensure statesize is non-zero") Reported-by:
Jonas Eymann <J.Eymann@gmx.net> Signed-off-by:
Horia Geant? <horia.geanta@nxp.com> Signed-off-by:
-
Catalin Vasile authored
commit e930c765 upstream. caam_jr_alloc() used to return NULL if a JR device could not be allocated for a session. In turn, every user of this function used IS_ERR() function to verify if anything went wrong, which does NOT look for NULL values. This made the kernel crash if the sanity check failed, because the driver continued to think it had allocated a valid JR dev instance to the session and at some point it tries to do a caam_jr_free() on a NULL JR dev pointer. This patch is a fix for this issue. Signed-off-by:
Catalin Vasile <cata.vasile@nxp.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 59643d15 upstream. If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE then the DIV_ROUND_UP() will return zero. Here's the details: # echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb tracing_entries_write() processes this and converts kb to bytes. 18014398509481980 << 10 = 18446744073709547520 and this is passed to ring_buffer_resize() as unsigned long size. size = DIV_ROUND_UP(size, BUF_PAGE_SIZE); Where DIV_ROUND_UP(a, b) is (a + b - 1)/b BUF_PAGE_SIZE is 4080 and here 18446744073709547520 + 4080 - 1 = 18446744073709551599 where 18446744073709551599 is still smaller than 2^64 2^64 - 18446744073709551599 = 17 But now 18446744073709551599 / 4080 = 4521260802379792 and size = size * 4080 = 18446744073709551360 This is checked to make sure its still greater than 2 * 4080, which it is. Then we convert to the number of buffer pages needed. nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE) but this time size is 18446744073709551360 and 2^64 - (18446744073709551360 + 4080 - 1) = -3823 Thus it overflows and the resulting number is less than 4080, which makes 3823 / 4080 = 0 an nr_pages is set to this. As we already checked against the minimum that nr_pages may be, this causes the logic to fail as well, and we crash the kernel. There's no reason to have the two DIV_ROUND_UP() (that's just result of historical code changes), clean up the code and fix this bug. Fixes: 83f40318 ("ring-buffer: Make removal of ring buffer pages atomic") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 9b94a8fb upstream. The size variable to change the ring buffer in ftrace is a long. The nr_pages used to update the ring buffer based on the size is int. On 64 bit machines this can cause an overflow problem. For example, the following will cause the ring buffer to crash: # cd /sys/kernel/debug/tracing # echo 10 > buffer_size_kb # echo 8556384240 > buffer_size_kb Then you get the warning of: WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260 Which is: RB_WARN_ON(cpu_buffer, nr_removed); Note each ring buffer page holds 4080 bytes. This is because: 1) 10 causes the ring buffer to have 3 pages. (10kb requires 3 * 4080 pages to hold) 2) (2^31 / 2^10 + 1) * 4080 = 8556384240 The value written into buffer_size_kb is shifted by 10 and then passed to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760 3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE which is 4080. 8761737461760 / 4080 = 2147484672 4) nr_pages is subtracted from the current nr_pages (3) and we get: 2147484669. This value is saved in a signed integer nr_pages_to_update 5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int turns into the value of -2147482627 6) As the value is a negative number, in update_pages_handler() it is negated and passed to rb_remove_pages() and 2147482627 pages will be removed, which is much larger than 3 and it causes the warning because not all the pages asked to be removed were removed. Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001 Fixes: 7a8e76a3 ("tracing: unified trace buffer") Reported-by:
Hao Qin <QEver.cn@gmail.com> Signed-off-by:
-
John Stultz authored
commit cd9e2e5d upstream. In testing with HiKey, we found that since commit 3f30b158 ("asix: On RX avoid creating bad Ethernet frames"), we're seeing lots of noise during network transfers: [ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988 [ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4 [ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4 [ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988 [ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4 [ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4 [ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988 [ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4 [ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4 And network throughput ends up being pretty bursty and slow with a overall throughput of at best ~30kB/s (where as previously we got 1.1MB/s with the slower USB1.1 "full speed" host). We found the issue also was reproducible on a x86_64 system, using a "high-speed" USB2.0 port but the throughput did not measurably drop (possibly due to the scp transfer being cpu bound on my slow test hardware). After lots of debugging, I found the check added in the problematic commit seems to be calculating the offset incorrectly. In the normal case, in the main loop of the function, we do: (where offset is zero, or set to "offset += (copy_length + 1) & 0xfffe" in the previous loop) rx->header = get_unaligned_le32(skb->data + offset); offset += sizeof(u32); But the problematic patch calculates: offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32); rx->header = get_unaligned_le32(skb->data + offset); Adding some debug logic to check those offset calculation used to find rx->header, the one in problematic code is always too large by sizeof(u32). Thus, this patch removes the incorrect " + sizeof(u32)" addition in the problematic calculation, and resolves the issue. Cc: Dean Jenkins <Dean_Jenkins@mentor.com> Cc: "David B. Robins" <linux@davidrobins.net> Cc: Mark Craske <Mark_Craske@mentor.com> Cc: Emil Goode <emilgoode@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: YongQin Liu <yongqin.liu@linaro.org> Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Ivan Vecera <ivecera@redhat.com> Cc: linux-usb@vger.kernel.org Cc: netdev@vger.kernel.org Reported-by:
Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Stefan Metzmacher authored
commit 1a967d6c upstream. Only server which map unknown users to guest will allow access using a non-null NTLMv2_Response. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
Stefan Metzmacher <metze@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Stefan Metzmacher authored
commit 777f69b8 upstream. Only server which map unknown users to guest will allow access using a non-null NTChallengeResponse. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
-
Stefan Metzmacher authored
commit fa8f3a35 upstream. Only server which map unknown users to guest will allow access using a non-null LMChallengeResponse. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
-
Stefan Metzmacher authored
commit cfda35d9 upstream. See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client: ... Set NullSession to FALSE If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND (AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1) OR AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0)) -- Special case: client requested anonymous authentication Set NullSession to TRUE ... Only server which map unknown users to guest will allow access using a non-null NTChallengeResponse. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
-
Steve French authored
commit 897fba11 upstream. Wrong return code was being returned on SMB3 rmdir of non-empty directory. For SMB3 (unlike for cifs), we attempt to delete a directory by set of delete on close flag on the open. Windows clients set this flag via a set info (SET_FILE_DISPOSITION to set this flag) which properly checks if the directory is empty. With this patch on smb3 mounts we correctly return "DIRECTORY NOT EMPTY" on attempts to remove a non-empty directory. Signed-off-by:
Steve French <steve.french@primarydata.com> Acked-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
-
Jiri Olsa authored
commit ef3f00a4 upstream. When booting with nr_cpus=1, uncore_pci_probe tries to init the PCI/uncore also for the other packages and fails with warning when they are not found. The warning is bogus because it's correct to fail here for packages which are not initialized. Remove it and return silently. Fixes: cf6d445f "perf/x86/uncore: Track packages, not per CPU data" Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Cc: stable@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Matt Evans authored
commit e4fe9e7d upstream. The EC field of the constructed ESR is conditionally modified by ORing in ESR_ELx_EC_DABT_LOW for a data abort. However, ESR_ELx_EC_SHIFT is missing from this condition. Signed-off-by:
Matt Evans <matt.evans@arm.com> Acked-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Marc Zyngier authored
commit d4b9e079 upstream. The ARM architecture mandates that when changing a page table entry from a valid entry to another valid entry, an invalid entry is first written, TLB invalidated, and only then the new entry being written. The current code doesn't respect this, directly writing the new entry and only then invalidating TLBs. Let's fix it up. Reported-by:
-
Julien Grall authored
commit f228b494 upstream. The loop that browses the array compat_hwcap_str will stop when a NULL is encountered, however NULL is missing at the end of array. This will lead to overrun until a NULL is found somewhere in the following memory. In reality, this works out because the compat_hwcap2_str array tends to follow immediately in memory, and that *is* terminated correctly. Furthermore, the unsigned int compat_elf_hwcap is checked before printing each capability, so we end up doing the right thing because the size of the two arrays is less than 32. Still, this is an obvious mistake and should be fixed. Note for backporting: commit 12d11817 ("arm64: Move /proc/cpuinfo handling code") moved this code in v4.4. Prior to that commit, the same change should be made in arch/arm64/kernel/setup.c. Fixes: 44b82b77 "arm64: Fix up /proc/cpuinfo" Signed-off-by:
Julien Grall <julien.grall@arm.com> Signed-off-by:
-
Catalin Marinas authored
commit 282aa705 upstream. The update to the accessed or dirty states for block mappings must be done atomically on hardware with support for automatic AF/DBM. The ptep_set_access_flags() function has been fixed as part of commit 66dbd6e6 ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM"). This patch brings pmdp_set_access_flags() in line with the pte counterpart. Fixes: 2f4b829c ("arm64: Add support for hardware updates of the access and dirty pte bits") Reviewed-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Catalin Marinas authored
commit 66dbd6e6 upstream. When hardware updates of the access and dirty states are enabled, the default ptep_set_access_flags() implementation based on calling set_pte_at() directly is potentially racy. This triggers the "racy dirty state clearing" warning in set_pte_at() because an existing writable PTE is overridden with a clean entry. There are two main scenarios for this situation: 1. The CPU getting an access fault does not support hardware updates of the access/dirty flags. However, a different agent in the system (e.g. SMMU) can do this, therefore overriding a writable entry with a clean one could potentially lose the automatically updated dirty status 2. A more complex situation is possible when all CPUs support hardware AF/DBM: a) Initial state: shareable + writable vma and pte_none(pte) b) Read fault taken by two threads of the same process on different CPUs c) CPU0 takes the mmap_sem and proceeds to handling the fault. It eventually reaches do_set_pte() which sets a writable + clean pte. CPU0 releases the mmap_sem d) CPU1 acquires the mmap_sem and proceeds to handle_pte_fault(). The pte entry it reads is present, writable and clean and it continues to pte_mkyoung() e) CPU1 calls ptep_set_access_flags() If between (d) and (e) the hardware (another CPU) updates the dirty state (clears PTE_RDONLY), CPU1 will override the PTR_RDONLY bit marking the entry clean again. This patch implements an arm64-specific ptep_set_access_flags() function to perform an atomic update of the PTE flags. Fixes: 2f4b829c ("arm64: Add support for hardware updates of the access and dirty pte bits") Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Tested-by:
-
Catalin Marinas authored
commit 5bb1cc0f upstream. Currently, pmd_present() only checks for a non-zero value, returning true even after pmd_mknotpresent() (which only clears the type bits). This patch converts pmd_present() to using pte_present(), similar to the other pmd_*() checks. As a side effect, it will return true for PROT_NONE mappings, though they are not yet used by the kernel with transparent huge pages. For consistency, also change pmd_mknotpresent() to only clear the PMD_SECT_VALID bit, even though the PMD_TABLE_BIT is already 0 for block mappings (no functional change). The unused PMD_SECT_PROT_NONE definition is removed as transparent huge pages use the pte page prot values. Fixes: 9c7e535f ("arm64: mm: Route pmd thp functions through pte equivalents") Reviewed-by:
-
Catalin Marinas authored
commit 911f56ee upstream. With hardware AF/DBM support, pmd modifications (transparent huge pages) should be performed atomically using load/store exclusive. The initial patches defined the get-and-clear function and __HAVE_ARCH_* macro without the "huge" word, leaving the pmdp_huge_get_and_clear() to the default, non-atomic implementation. Fixes: 2f4b829c ("arm64: Add support for hardware updates of the access and dirty pte bits") Reviewed-by:
-
- 15 May, 2016 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fix from Thomas Gleixner: "Just the missing compat entry for the new pread/writev2" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86: Use compat version for preadv2 and pwritev2
-
- 14 May, 2016 11 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix mvneta/bm dependencies, from Arnd Bergmann. 2) RX completion hw bug workaround in bnxt_en, from Michael Chan. 3) Kernel pointer leak in nf_conntrack, from Linus. 4) Hoplimit route attribute limits not enforced properly, from Paolo Abeni. 5) qlcnic driver NULL deref fix from Dan Carpenter. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: arm64: bpf: jit JMP_JSET_{X,K} net/route: enforce hoplimit max value nf_conntrack: avoid kernel pointer value leak in slab name drivers: net: xgene: fix register offset drivers: net: xgene: fix statistics counters race condition drivers: net: xgene: fix ununiform latency across queues drivers: net: xgene: fix sharing of irqs drivers: net: xgene: fix IPv4 forward crash xen-netback: fix extra_info handling in xenvif_tx_err() net: mvneta: bm: fix dependencies again bnxt_en: Add workaround to detect bad opaque in rx completion (part 2) bnxt_en: Add workaround to detect bad opaque in rx completion (part 1) qlcnic: potential NULL dereference in qlcnic_83xx_get_minidump_template() -
Zi Shen Lim authored
Original implementation commit e54bcde3 ("arm64: eBPF JIT compiler") had the relevant code paths, but due to an oversight always fail jiting. As a result, we had been falling back to BPF interpreter whenever a BPF program has JMP_JSET_{X,K} instructions. With this fix, we confirm that the corresponding tests in lib/test_bpf continue to pass, and also jited. ... [ 2.784553] test_bpf: #30 JSET jited:1 188 192 197 PASS [ 2.791373] test_bpf: #31 tcpdump port 22 jited:1 325 677 625 PASS [ 2.808800] test_bpf: #32 tcpdump complex jited:1 323 731 991 PASS ... [ 3.190759] test_bpf: #237 JMP_JSET_K: if (0x3 & 0x2) return 1 jited:1 110 PASS [ 3.192524] test_bpf: #238 JMP_JSET_K: if (0x3 & 0xffffffff) return 1 jited:1 98 PASS [ 3.211014] test_bpf: #249 JMP_JSET_X: if (0x3 & 0x2) return 1 jited:1 120 PASS [ 3.212973] test_bpf: #250 JMP_JSET_X: if (0x3 & 0xffffffff) return 1 jited:1 89 PASS ... Fixes: e54bcde3 ("arm64: eBPF JIT compiler") Signed-off-by:
Zi Shen Lim <zlim.lnx@gmail.com> Acked-by:
Yang Shi <yang.shi@linaro.org> Signed-off-by:
-
Paolo Abeni authored
Currently, when creating or updating a route, no check is performed in both ipv4 and ipv6 code to the hoplimit value. The caller can i.e. set hoplimit to 256, and when such route will be used, packets will be sent with hoplimit/ttl equal to 0. This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4 ipv6 route code, substituting any value greater than 255 with 255. This is consistent with what is currently done for ADVMSS and MTU in the ipv4 code. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Linus Torvalds authored
The slab name ends up being visible in the directory structure under /sys, and even if you don't have access rights to the file you can see the filenames. Just use a 64-bit counter instead of the pointer to the 'net' structure to generate a unique name. This code will go away in 4.7 when the conntrack code moves to a single kmemcache, but this is the backportable simple solution to avoiding leaking kernel pointers to user space. Fixes: 5b3501fa ("netfilter: nf_conntrack: per netns nf_conntrack_cachep") Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs fixes from Al Viro: "Overlayfs fixes from Miklos, assorted fixes from me. Stable fodder of varying severity, all sat in -next for a while" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: ovl: ignore permissions on underlying lookup vfs: add lookup_hash() helper vfs: rename: check backing inode being equal vfs: add vfs_select_inode() helper get_rock_ridge_filename(): handle malformed NM entries ecryptfs: fix handling of directory opening atomic_open(): fix the handling of create_error fix the copy vs. map logics in blk_rq_map_user_iov() do_splice_to(): cap the size before passing to ->splice_read()
-
David S. Miller authored
Iyappan Subramanian says: ==================== drivers: net: xgene: Bug fixes This patch set addresses the following bug fixes that were found during testing. 1. IPv4 forward test crash - drivers: net: xgene: fix IPv4 forward crash 2. Sharing of irqs - drivers: net: xgene: fix sharing of irqs 3. Ununiform latency across queues - drivers: net: xgene: fix ununiform latency across queues 4. Fix statistics counters race condition - drivers: net: xgene: fix statistics counters race condition 5. Correcting register offset and field lengths - drivers: net: xgene: fix register offset v2: Address review comments from v1 - Defer TSO fix, and reposting all other patches from v1 v1: - Initial version ==================== Signed-off-by:Iyappan Subramanian <isubramanian@apm.com> Signed-off-by:
-
Iyappan Subramanian authored
This patch fixes SG_RX_DV_GATE_REG_0_ADDR register offset and ring state field lengths. Signed-off-by:
Toan Le <toanle@apm.com> Signed-off-by:
-
Iyappan Subramanian authored
This patch fixes the race condition on updating the statistics counters by moving the counters to the ring structure. Signed-off-by:
-
Iyappan Subramanian authored
This patch addresses ununiform latency across queues by adding more queues to match with, upto number of CPU cores. Also, number of interrupts are increased and the channel numbers are reordered. Signed-off-by:
-
Iyappan Subramanian authored
Since hardware doesn't allow sharing of interrupts, this patch fixes the same by removing IRQF_SHARED flag. Signed-off-by:
-
Iyappan Subramanian authored
This patch fixes the crash observed during IPv4 forward test by setting the drop field in the dbptr. Signed-off-by:
-
