- 28 Nov, 2010 21 commits
-
-
Adam Edvardsson authored
Occasionally, it seems that some race is causing the interrupts to not be reenabled otherwise with the end result that networking just stops working. Enabling interrupts after calling napi_complete is more in line with what other drivers do. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jonas Bonn authored
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jonas Bonn authored
This patch adds the ability to describe ethernet devices via a flattened device tree. As device tree remains an optional feature, these bits all need to be guarded by CONFIG_OF ifdefs. MAC address is settable via the device tree parameter "local-mac-address"; however, the selection of the phy id is limited to probing, for now. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
-
andrew hendry authored
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
andrew hendry authored
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
andrew hendry authored
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
andrew hendry authored
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
andrew hendry authored
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladislav Zolotarov authored
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
In KVM passthrough mode, the driver may not have config access to non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register access to setup mailbox swapping can be done using MMIO. Update version to 2.0.20. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eddie Wai authored
The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be cleared and polling for pending DMAs to complete before chip reset. Without this step, we've seen NMIs during repeated resets of the chip. Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
John Fastabend authored
Now that the vlan device is lockless and single queue do not transfer the real num queues. This is causing a BUG_ON to occur. kernel BUG at net/8021q/vlan.c:345! Call Trace: [<ffffffff813fd6e8>] ? fib_rules_event+0x28/0x1b0 [<ffffffff814ad2b5>] notifier_call_chain+0x55/0x80 [<ffffffff81089156>] raw_notifier_call_chain+0x16/0x20 [<ffffffff813e5af7>] call_netdevice_notifiers+0x37/0x70 [<ffffffff813e6756>] netdev_features_change+0x16/0x20 [<ffffffffa02995be>] ixgbe_fcoe_enable+0xae/0x100 [ixgbe] [<ffffffffa01da06a>] vlan_dev_fcoe_enable+0x2a/0x30 [8021q] [<ffffffffa02d08c3>] fcoe_create+0x163/0x630 [fcoe] [<ffffffff811244d5>] ? mmap_region+0x255/0x5a0 [<ffffffff81080ef0>] param_attr_store+0x50/0x80 [<ffffffff810809b6>] module_attr_store+0x26/0x30 [<ffffffff811b9db2>] sysfs_write_file+0xf2/0x180 [<ffffffff8114fc88>] vfs_write+0xc8/0x190 [<ffffffff81150621>] sys_write+0x51/0x90 [<ffffffff8100c0b2>] system_call_fastpath+0x16/0x1b Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
When testing struct netdev_queue state against FROZEN bit, we also test XOFF bit. We can test both bits at once and save some cycles. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shan Wei authored
1. IPV6_TLV_TEL_DST_SIZE This has not been using for several years since created. 2. RT6_INFO_LEN commit 33120b30 kill all RT6_INFO_LEN's references, but only this definition remained. commit 33120b30 Author: Alexey Dobriyan <adobriyan@sw.ru> Date: Tue Nov 6 05:27:11 2007 -0800 [IPV6]: Convert /proc/net/ipv6_route to seq_file interface Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Uwe Kleine-König authored
Cc: netdev@vger.kernel.org Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rajesh Borundia authored
In kdump environment do not depend on reset_devices parameter to reset the device as the parameter may become obsolete. Instead use an adapter specific mechanism to determine if the device needs a reset. Driver maintains a count of number of pci functions probed and decrements the count when remove handler of that pci function is called. If the first probe, probe of function 0, detects the count as non zero then reset the device. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rajesh Borundia authored
In kdump environment do not depend upon reset_devices parameter to reset the pci function as this parameter may become obsolete. Instead use an adapter specific mechanism to determine if the pci function needs to be reset. Per function refcount is maintained in driver, which is set in probe and reset in remove handler of adapter. If the probe detects the count as non zero then reset the function. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shan Wei authored
These macros have been existed for several years since v2.6.12-rc2. But they never be used. So remove them now. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Thomas Graf authored
As David pointed out correctly, updates to af-specific attributes are currently not atomic. If multiple changes are requested and one of them fails, previous updates may have been applied already leaving the link behind in a undefined state. This patch splits the function parse_link_af() into two functions validate_link_af() and set_link_at(). validate_link_af() is placed to validate_linkmsg() check for errors as early as possible before any changes to the link have been made. set_link_af() is called to commit the changes later. This method is not fail proof, while it is currently sufficient to make set_link_af() inerrable and thus 100% atomic, the validation function method will not be able to detect all error scenarios in the future, there will likely always be errors depending on states which are f.e. not protected by rtnl_mutex and thus may change between validation and setting. Also, instead of silently ignoring unknown address families and config blocks for address families which did not register a set function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are returned to avoid comitting 4 out of 5 update requests without notifying the user. Signed-off-by: Thomas Graf <tgraf@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Use vzalloc() and vzalloc_node() in net drivers Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sathya Perla authored
Key changes are: - EQ ids are not assigned consecutively in Lancer. So, fix mapping of MSIx vector to EQ-id. - BAR mapping and some req locations different for Lancer. - TCP,UDP,IP checksum fields must be compulsorily set in TX wrb for TSO in Lancer. - CEV_IST reg not present in Lancer; so, peek into event queue to check for new entries - cq_create and mcc_create cmd interface is different for Lancer; handle accordingly Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 24 Nov, 2010 19 commits
-
-
Tom Herbert authored
This patch implements transmit packet steering (XPS) for multiqueue devices. XPS selects a transmit queue during packet transmission based on configuration. This is done by mapping the CPU transmitting the packet to a queue. This is the transmit side analogue to RPS-- where RPS is selecting a CPU based on receive queue, XPS selects a queue based on the CPU (previously there was an XPS patch from Eric Dumazet, but that might more appropriately be called transmit completion steering). Each transmit queue can be associated with a number of CPUs which will use the queue to send packets. This is configured as a CPU mask on a per queue basis in: /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus The mappings are stored per device in an inverted data structure that maps CPUs to queues. In the netdevice structure this is an array of num_possible_cpu structures where each structure holds and array of queue_indexes for queues which that CPU can use. The benefits of XPS are improved locality in the per queue data structures. Also, transmit completions are more likely to be done nearer to the sending thread, so this should promote locality back to the socket on free (e.g. UDP). The benefits of XPS are dependent on cache hierarchy, application load, and other factors. XPS would nominally be configured so that a queue would only be shared by CPUs which are sharing a cache, the degenerative configuration woud be that each CPU has it's own queue. Below are some benchmark results which show the potential benfit of this patch. The netperf test has 500 instances of netperf TCP_RR test with 1 byte req. and resp. bnx2x on 16 core AMD XPS (16 queues, 1 TX queue per CPU) 1234K at 100% CPU No XPS (16 queues) 996K at 100% CPU Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tom Herbert authored
In dev_pick_tx, don't do work in calculating queue index or setting the index in the sock unless the device has more than one queue. This allows the sock to be set only with a queue index of a multi-queue device which is desirable if device are stacked like in a tunnel. We also allow the mapping of a socket to queue to be changed. To maintain in order packet transmission a flag (ooo_okay) has been added to the sk_buff structure. If a transport layer sets this flag on a packet, the transmit queue can be changed for the socket. Presumably, the transport would set this if there was no possbility of creating OOO packets (for instance, there are no packets in flight for the socket). This patch includes the modification in TCP output for setting this flag. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
dev_base_lock is the legacy way to lock the device list, and is planned to disappear. (writers hold RTNL, readers hold RCU lock) Convert rdma_translate_ip() and update_ipv6_gids() to RCU locking. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are halved. (commit f8d570a4 added two pointers in this structure) scm_fp_dup() should not copy whole structure (and trigger kmemcheck warnings), but only the used part. While we are at it, only allocate needed size. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
ipv6_sk_mc_lock rwlock becomes a spinlock. readers (inet6_mc_check()) now takes rcu_read_lock() instead of read lock. Writers dont need to disable BH anymore. struct ipv6_mc_socklist objects are reclaimed after one RCU grace period. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
This patch updates the PM support using the dev_pm_ops and reviews the hibernation support. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
This patch adds in the plat_stmmacenet_data the init and exit callbacks that can be used for invoking specific platform functions. For example, on ST targets, these call the PAD manager functions to set PIO lines and syscfg registers. The patch removes the stmmac_claim_resource only used on STM Kernels as well. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
This patch tidies-up the stmmac_priv structure that had many fileds alredy defined in the plat_stmmacenet_data structure. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladislav Zolotarov authored
Move the interrupt mode configuration and NAPIs adding before a register_netdev() call to prevent netdev->open() from running before these functions are done. Advance a driver version number. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reported-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
According to Eric's suggestion: Disable local BHes to prevent a dead-lock situation between sch_direct_xmit() (Soft_IRQ context) and bnx2x_tx_int (called by bnx2x_run_loopback() - syscall context), as both are taking a netif_tx_lock(). Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This structure isn't used anywhere in the driver. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch enables the gphy autopowerdown feature in the phy for all new devices that support it. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Using dma_alloc_coherent() permits to use GFP_KERNEL allocations instead of GFP_ATOMIC ones. Its better when a machine is out of memory, because this allows driver to sleep to get its memory and succeed its init, especially when allocating high order pages. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
All TSS bugs have been fixed in the 5719. This patch reenables the feature. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
The multiple DMA read engine bugs have been fixed on the 5719. This patch reenables support for this feature. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch reorders and realigns the tg3_napi members for a ~3-4% performance improvement on small packet performance tests. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Under load, there an internal FIFO can overflow on the 5719. The fix is to scale back the PCIe maximum read request size based on the current link speed and width. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
The APE needs certain bits in the mac_mode register to be enabled for traffic to flow correctly. This patch changes the code to always enable these bits in the presence of the APE. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-