- 24 Nov, 2011 40 commits
-
-
Leonid V. Fedorenchik authored
Fix indent of statement to use tab instead of spaces. Signed-off-by:
Leonid V. Fedorenchik <leonidsbox@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Leonid V. Fedorenchik authored
Change column of line continuation character ('\') and fix indent of multiline defines. Also line up remaining constant defines. Signed-off-by: -
Leonid V. Fedorenchik authored
Line up defines to the same column. Signed-off-by:
-
Leonid V. Fedorenchik authored
Change obscure line endings to less obscure ones. (improve readability) Signed-off-by:
-
Leonid V. Fedorenchik authored
Move operator of complex expression to the end of the lines to preserve consistency. Signed-off-by:
-
Leonid V. Fedorenchik authored
Change wrong indent (with spaces and less than 7 columns) of statements to tabs. Signed-off-by:
-
Leonid V. Fedorenchik authored
Change obscure line endings to less obscure ones. (improve readability) Signed-off-by:
-
Leonid V. Fedorenchik authored
Delete unnecessary space before indented statement. Signed-off-by:
-
Leonid V. Fedorenchik authored
Add curly braces around else clause because corresponding if has them. Signed-off-by:
-
Leonid V. Fedorenchik authored
Line up comments to the same column. Signed-off-by:
-
Axel Lin authored
i2c_master_send returns negative errno, or else the number of bytes written. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
-
Ben Hutchings authored
lirc_serial_probe() must fail if request_irq() returns an error, even if it isn't EBUSY or EINVAL, Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
Device not found? ENODEV, not EINVAL. Write to read-only device? EPERM, not EBADF. Invalid argument? EINVAL, not ENOSYS. Unsupported ioctl? ENOIOCTLCMD, not ENOSYS. Another function returned an error code? Use that, don't replace it. Signed-off-by:
-
Ben Hutchings authored
A resume function cannot remove the device it is resuming! Signed-off-by:
-
Ben Hutchings authored
Failure to allocate the I/O region leaves the IRQ allocated. A later failure leaves them both allocated. Reported-by:
Torsten Crass <torsten.crass@eBiology.de> Signed-off-by:
-
Ben Hutchings authored
Currently the module init function registers a platform_device and only then allocates its IRQ and I/O region. This allows allocation to race with the device's suspend() function. Instead, allocate resources in the platform driver's probe() function and free them in the remove() function. The module exit function removes the platform device before the character device that provides access to it. Change it to reverse the order of initialisation. Signed-off-by:
-
Hans Verkuil authored
The function setup_vpif_input_channel_mode() used the VSCLKDIS register instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0 used a different clock from channel 1. Clearly a copy-and-paste error. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
-
Antti Palosaari authored
I have been working many years without problems. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
I have been working many years without problems. Signed-off-by:
-
Antti Palosaari authored
It is param that could be potentially unsupported and due to that it is good idea to check it very first. Signed-off-by:
-
Antti Palosaari authored
All tuners used with cxd2820r offers IF frequency so switch that. Signed-off-by:
-
Antti Palosaari authored
Chip configures IF frequency resolution of 50 kHz. Round it nearest. Off-by 50 kHz is almost nothing in real life... Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Get IF frequency from tuner if tuner provides it. Remove TDA18271 and TDA18218 IF frequency hacks since both tuners provides .get_if_frequency(). Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Paul Bolle authored
Commit ede676c7 ("[...] add digital support for PV SBTVD hybrid") added "select MEDIA_TUNER_NXP18271" to the VIDEO_CX231XX_DVB Kconfig entry. But there's no Kconfig symbol MEDIA_TUNER_NXP18271. That should have been MEDIA_TUNER_TDA18271. (The code added in that commit uses tda18271_attach, which is only available if MEDIA_TUNER_TDA18271 is set.) The selects of MEDIA_TUNER_XC5000 and MEDIA_TUNER_TDA18271 should only be done if MEDIA_TUNER_CUSTOMISE isn't set. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Heungjun Kim authored
Add the maintainers for the m5mols driver Signed-off-by:
HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Alfredo Jesús Delaiti authored
This patch supports card Mygica X8507 (analog part) This controller is a copy of driver card Mygica X8506 This patch depends on patch cx23885-alsa To do: FM, ISDB-t, remote control, audio for composite1, S-Video and video component. Signed-off-by:
Alfredo J. Delaiti <alfredodelaiti@netscape.net> Signed-off-by:
-
Jean Delvare authored
There's one comment that has been copied from bttv to many other media/video drivers: /* init + register i2c algo-bit adapter */ Meanwhile, many drivers use hardware I2C implementations instead of relying on i2c-algo-bit, so this comment is misleading. Remove the reference to "algo-bit" from all drivers, to avoid any confusion. This is the best way to ensure that the comments won't go out of sync again. Anyone interested in the implementation details would rather look at the code itself. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/dvb/firewire/firedtv-avc.c: In function ‘avc_tuner_tuneqpsk’: drivers/media/dvb/firewire/firedtv-avc.c:394:4: warning: enumeration value ‘ROLLOFF_15’ not handled in switch [-Wswitch] drivers/media/dvb/firewire/firedtv-avc.c:394:4: warning: enumeration value ‘ROLLOFF_13’ not handled in switch [-Wswitch] Signed-off-by: -
Mauro Carvalho Chehab authored
drivers/media/video/em28xx/em28xx-cards.c:339:30: warning: ‘hauppauge_930c_gpio’ defined but not used [-Wunused-variable] drivers/media/video/em28xx/em28xx-dvb.c: In function ‘em28xx_dvb_init’: drivers/media/video/em28xx/em28xx-dvb.c:886:3: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement] Signed-off-by: -
Sylwester Nawrocki authored
Add missing dev argument in dev_err() call to correct an error introduced in commit 88010289Signed-off-by:
Sylwester Nawrocki <snjw23@gmail.com> Signed-off-by:
-
Andrew Vincer authored
Fixed submit urb logic so hardware doesn't hang trying to transmit signal data Removed unneeded enable/disable detector commands in redrat3_transmit_ir (the hardware does this anyway) and converted arguments to unsigned as per 5588dc2bSigned-off-by:
Andrew Vincer <andrew@redrat.co.uk> Cc: Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Dan Carpenter authored
Smatch complains that the wrong limiter is used here: drivers/media/dvb/ttpci/av7110.c +906 dvb_feed_start_pid(12) error: buffer overflow 'npids' 5 <= 19 Here is the problem code: 905 i = dvbdmxfeed->pes_type; 906 npids[i] = (pid[i]&0x8000) ? 0 : pid[i]; "npids" is a 5 element array declared on the stack. If dvbdmxfeed->pes_type is more than 4 we probably put a (u16)0 past the end of the array. If dvbdmxfeed->pes_type is over 4 the rest of the function doesn't do anything. dvbdmxfeed->pes_type is capped at less than DMX_TS_PES_OTHER (20) in the caller function, but I changed it to less than or equal to DMX_TS_PES_PCR (4). Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Jose Alberto Reguero authored
This patch fix a bug in the i2c code of ttusb2 driver. Signed-off-by:
Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by:
-
Hans Verkuil authored
I get this error when compiling for_v3.3: There is a include <linux/module.h> missing. Signed-off-by:
-
Dan Carpenter authored
priv gets dereferenced in mt9t112_set_params() so we should return before calling that. Signed-off-by:
-
lawrence rust authored
This patch to the IR RC6 decoder adds support for variable length mode-6A frames which can range in size from 8 to 128 bits. Please refer to the following link for a detailed explanation or RC6 frames: http://slydiman.narod.ru/scr/kb/rc6.htm This change removes the assumption that frames are fixed length (currently either 24 or 32 data bits) and actually counts the number of bits until an end of frame marker is seen. [mchehab@redhat.com: Tested with a RC-6(0) IR - 16 bits] Tested-by:
-
