Add support for the AXP717 PMIC. The AXP717 PMIC allows for detection
of USB type like the AXP813, but has little in common otherwise with
the other AXP PMICs. The USB charger is able to provide between
100000uA and 3250000uA of power, and can measure the VBUS input in mV
with up to 14 bits of precision.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-14-macroalpha82@gmail.com
[fix axp717_usb_power_desc.usb_types]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add binding information for AXP717.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240821215456.962564-11-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add support for the AXP717. It has BC 1.2 detection like the AXP813
and uses ADC channels like all other AXP devices, but otherwise is
very different requiring new registers for most functions.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-10-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Immutable branch between MFD, IIO and power-supply providing the
register definitions needed for AXP717 support in the axp20x
axp20x_battery and axp20x_usb_power drivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20240828093447.271503-1-colin.i.king@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Changing usb_types type from array to bitmap in the power_supply_desc
struct requires updating power-supply drivers living in different
subsystem, so it is handled via an immutable branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.

This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.

This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Move power_supply_show_enum_with_available() higher up in
the power_supply_sysfs.c file.

This is a preparation patch to avoid needing a forward declaration
when replacing power_supply_show_usb_type() with it later on.

This commit only moves the function, there are no changes to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-6-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Turn power_supply_charge_behaviour_show() into a generic function for
showing enum values with their available (for writing) values shown
and the current value shown surrounded by sqaure-brackets like
the show() output for "usb_type" and "charge_behaviour".

This is a preparation patch for refactoring the "usb_type" property
handling to use a bitmask indicating available usb-types + this new
generic function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-5-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The "usb_type" property must be read-only for charger power-supply devices,
see: Documentation/ABI/testing/sysfs-class-power.

But the rt9467 driver allows writing 0/1 to it to disable/enable charging.
Other charger drivers use the "status" property for this and the rt9467
code also allows writing 0/1 to its "status" property and this does
the exact same thing as writing 0/1 to its "usb_type" property.

Drop write support for the "usb_type" property making it readonly to match
the ABI documentation. If userspace wants to disable/enable charging it
can use the "status" property for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-4-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

power_supply_sysfs.c accept wrrites of strings to "usb_type" for strings
values matching an entry in POWER_SUPPLY_USB_TYPE_TEXT[]. If such a
string value is written then the int value passed to ucs1002_set_property()
will be an enum power_supply_usb_type value.

Before this change ucs1002_set_usb_type() expected the value to be an index
into ucs1002_usb_types[]. Adjust ucs1002_set_usb_type() to use the enum
value directly so that writing string values works.

The list of supported types in ucs1002_usb_types[] is: PD, SDP, DCP, CDP.
The [POWER_SUPPLY_USB_TYPE_]SDP, DCP and CDP enum labels have a value of
1, 2 and 3. So userspace selecting SDP, DCP or CDP by writing 1, 2 or 3
will keep working. POWER_SUPPLY_USB_TYPE_PD which is mapped to the ucs1002
dedicated mode however has a value of 6. Before this change writing 0 would
select the dedicated mode. To preserve userspace API compatibility also map
POWER_SUPPLY_USB_TYPE_UNKNOWN (which is 0) to the dedicated mode.

Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-3-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

According to Documentation/ABI/testing/sysfs-class-power the "usb_type"
property is Read-Only.

For power-supplies which consume USB power such as battery charger chips,
this is correct.

But the UCS1002 USB Port Power Controller driver which is a driver
for a chip which is a power-source for USB-A charging ports "usb_type"
is actually writable to configure the type of USB charger emulated
by the USB-A port.

Adjust the docs and the power_supply_sysfs.c code to adjust for this
new writeable use of "usb_type":

1. Update Documentation/ABI/testing/sysfs-class-power to document that
"usb_type" may be writable

2. Change the power_supply_attr type in power_supply_sysfs.c from
POWER_SUPPLY_ATTR() into POWER_SUPPLY_ENUM_ATTR() so that the various
usb_type string values from POWER_SUPPLY_TYPE_TEXT[] such as e.g.
"SDP" and "USB_PD" can be written to the "usb_type" attribute instead
of only accepting integer values.

Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-2-hdegoede@redhat.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

ModelGauge m5 and device configuration values are stored in nonvolatile
memory to prevent data loss if the IC loses power. Add read support for
the nonvolatile memory on MAX1720X devices.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240903063526.222890-1-dima.fedrau@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add support for the AXP717 PMIC to utilize the ADC (for reading
voltage, current, and temperature information from the PMIC) as well
as the USB charger and battery.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-12-macroalpha82@gmail.comSigned-off-by: Lee Jones <lee@kernel.org>

This struct is never modified, so mark it const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240828-power-supply-const-psy_tzd_ops-v1-1-dc27176fda5b@weissschuh.netSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There may be other backup reset methods available, do not halt
here so that other reset methods can be tried.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-5-afd@ti.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Function register_restart_handler() is deprecated. Using this new API
removes our need to keep and manage a struct notifier_block.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-4-afd@ti.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Simplify probe by fetching the regmap and its arguments in one call.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-3-afd@ti.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use device_get_match_data() for finding the matching node and fetching
the match data all in one.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-2-afd@ti.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The platform_driver_probe() helper is useful when the probe function
is in the _init section, that is not the case here. Use the normal
platform_driver_register() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-1-afd@ti.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The OCP board used a BlueField's GPIO pin for entering
low power mode. That board was not commercialized and
has been dropped from production so all its code is unused.
The new hardware requirement is to trigger a graceful shutdown
when that GPIO pin is toggled. So replace the unused low power
mode with a graceful shutdown.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240611134327.30975-1-asmaa@nvidia.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240710032023.2003742-1-nichen@iscas.ac.cnSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There are two charger current limit registers:

- Fast charge current limit (which controls current going from the
  charger to the battery);
- CHGIN input current limit (which controls current going into the
  charger through the cable).

Add the necessary functions to retrieve the CHGIN input limit (from CHARGER
regulator) and maximum fast charge current values, and expose them as power
supply properties.
Tested-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240816-max77693-charger-extcon-v4-3-050a0a9bfea0@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Commit 223a3b82 ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.

Fix this by applying the same conditional to determine which register
should be read.

This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.

This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).

Fixes: e5f3872d ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Document the monitored-battery property, which the existing driver can
use to set certain properties.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-8-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Allow users to specify a maximum input current for the device. Some
devices allow up to 3.25A of input current (such as the AXP717), which
may be too much for some implementations.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-7-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Allow specifying a hard limit of the maximum input current. Some PMICs
such as the AXP717 can pull up to 3.25A, so allow a value to be
specified that clamps this in the event the hardware is not designed
for it.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-6-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Make reading of the vbus value and configuring of the iio channels
device specific, to allow additional devices (such as the AXP717) to
be supported by this driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-5-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Move the configuration of battery specific information and available
iio channels from the probe function to a device specific routine,
allowing us to use this driver for devices with slightly different
configurations (such as the AXP717).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-4-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN and
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN values should be immutable
properties of the battery, but for this driver they are writable values
and used as the minimum and maximum values for charging. Remove the
DESIGN designation from these values.

Fixes: 46c202b5 ("power: supply: add battery driver for AXP20X and AXP22X PMICs")
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-3-macroalpha82@gmail.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Driver reads existing current value from two 8-bit registers, but then
compares only one of them with the new 16-bit value.  clang W=1 is also
not happy:

  twl4030_charger.c:243:16: error: variable 'cur_reg' set but not used [-Werror,-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240705113113.42851-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Allocate the memory with scoped/cleanup.h to reduce error handling and
make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240705113113.42851-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The SC27XX fuel gauge supports a low voltage alarm IRQ, which is used
for more accurate battery capacity measurements with lower voltages.

This was unfortunately never documented in bindings, do so now.

The only in-tree user (sc2731.dtsi) has had interrupts specified
since its initial fuel-gauge submission and the current kernel
driver returns an error when no interrupt is specified, so also
add it to the required list.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/Zr3SAHlq5A78QvrW@standask-GA-A55M-S2HPSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from platform_device_id table.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240819040831.2801543-1-ruanjinjie@huawei.comSigned-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The existing docs here are a bit vague. This reformats and rewords it,
and is based upon the wording originally used by the dell-laptop driver
battery documentation and also sysfs-class-power-wilco.

The wording for "Long Life" and "Bypass" remain the same, because I'm
unfamiliar with hardware that use them.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240820041942.30ed42f3@5400Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix RPM package build error caused by an incorrect locale setup

 - Mark modules.weakdep as ghost in RPM package

 - Fix the odd combination of -S and -c in stack protector scripts,
   which is an error with the latest Clang

* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: Fix '-S -c' in x86 stack protector scripts
  kbuild: rpm-pkg: ghost modules.weakdep file
  kbuild: rpm-pkg: Fix C locale setup

This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.

That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.

Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3a7e02c0 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.

The complexity of those macros stems from two issues:

 (a) trying to use them in situations that require a C constant
     expression (in static initializers and for array sizes)

 (b) the type sanity checking

and MIN_T/MAX_T avoids both of these issues.

Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.

But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.

However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.

This does exactly that.

Which in turn will then allow for much simpler implementations of
min_t()/max_t().  All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.

We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.

Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs

Pull UBI and UBIFS updates from Richard Weinberger:

 - Many fixes for power-cut issues by Zhihao Cheng

 - Another ubiblock error path fix

 - ubiblock section mismatch fix

 - Misc fixes all over the place

* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubi: Fix ubi_init() ubiblock_exit() section mismatch
  ubifs: add check for crypto_shash_tfm_digest
  ubifs: Fix inconsistent inode size when powercut happens during appendant writing
  ubi: block: fix null-pointer-dereference in ubiblock_create()
  ubifs: fix kernel-doc warnings
  ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
  mtd: ubi: Restore missing cleanup on ubi_init() failure path
  ubifs: dbg_orphan_check: Fix missed key type checking
  ubifs: Fix unattached inode when powercut happens in creating
  ubifs: Fix space leak when powercut happens in linking tmpfile
  ubifs: Move ui->data initialization after initializing security
  ubifs: Fix adding orphan entry twice for the same inode
  ubifs: Remove insert_dead_orphan from replaying orphan process
  Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
  ubifs: Don't add xattr inode into orphan area
  ubifs: Fix unattached xattr inode if powercut happens after deleting
  mtd: ubi: avoid expensive do_div() on 32-bit machines
  mtd: ubi: make ubi_class constant
  ubi: eba: properly rollback inside self_check_eba