mvebu fixes for v3.9 from Jason Cooper <jason@lakedaemon.net>:

The first four patches:

  89c58c19 rtc: rtc-mv: Add support for clk to avoid lockups
  de88747f gpio: mvebu: Add clk support to prevent lockup
  7bf5b408 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
  93fff4ce ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency

are Cc'd to stable since they were held over from the previous merge window.

The rest are a small collection of fixes and a couple of devicetree conversion
catchups.

* tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
  arm: mach-orion5x: fix typo in compatible string of a .dts file
  arm: mvebu: fix address-cells in mpic DT node
  arm: plat-orion: fix address decoding when > 4GB is used
  arm: mvebu: Reduce reg-io-width with UARTs
  ARM: Dove: add RTC device node
  arm: mvebu: enable the USB ports on Armada 370 Reference Design board
  ARM: dove: drop "select COMMON_CLK_DOVE"
  rtc: rtc-mv: Add support for clk to avoid lockups
  gpio: mvebu: Add clk support to prevent lockup
  ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
  ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Shawn Guo <shawn.guo@linaro.org>:

The 2nd take of imx fixes for 3.9:
 - Fix pll1_sys clk initial status
 - Fix a typo in imx DEBUG_LL Kconfig

* tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
  ARM: imx: pll1_sys should be an initial on clk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Shawn Guo <shawn.guo@linaro.org>:

The 2nd mxs fixes for 3.9:
 - Fix an error caused by incorrect conflict resolution when
   applying the patch

* tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: cfa10049: Fix fb initialisation function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

When building a multiplatform kernel, we could end up with a smaller
number of GPIOs than the one required by the platform the kernel was
running on.

Sort the max GPIO number by descending order so that we always take the
highest number required.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit f8c95fe6 (ARM: imx: support DEBUG_LL uart port selection for all
i.MX SoCs) had a typo that DEBUG_IMX50_IMX53_UART should be
DEBUG_IMX53_UART.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

We always boot from PLL1, so let's have pll1_sys in the clks_init_on
list to have clk prepare/enable use count match the hardware status,
so that drivers managing pll1_sys like cpufreq can get the use count
right from the start.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.

However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.

This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).

This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Setting the reg-io-width to 1 byte represents more accurate
description of the HW.

This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The commit:

  48be9ac9 ARM: Dove: split legacy and DT setup

removed the RTC initialization.  This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Commit 5b03df9a ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.

Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Commit 1fe42740 ("ARM: dts: mxs: Add the LCD to the 10049 board") seem
to have been applied with some fuzzyness, and the framebuffer
initialisation code for the CFA-10049 ended up in the CFA-10037
initialisation function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Do what commit f12a500e
("ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ") wanted to do.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v3.9-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fix few regressions, omap3 pm init with device tree, and some
issues with the legacy mux code.

* tag 'omap-for-v3.9-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: RX-51: add missing USB phy binding
  ARM: OMAP2+: Remove duplicate omap4430_init_late() declaration
  ARM: OMAP2+: mux: correct wrong error messages
  ARM: OMAP2+: mux: fix debugfs file permission
  ARM: OMAP2+: Fix unmet direct dependencies for zoom for 8250 serial
  ARM: OMAP3: board-generic: Add missing omap3_init_late
  ARM: OMAP2+: Fix broken gpmc support
  ARM: OMAP1: Fix build related to kgdb.h no longer including serial_8250.h

Commit 51482be9 (ARM: OMAP: USB: Add phy binding information) forgot to
add phy binding for RX-51, and as a result USB does not work anymore on
3.9-rc1. Add the missing binding.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

From Shawn Guo:
The mxs fixes for 3.9:
 - A few sparse warning fixes
 - Fix usb function regression caused by usb Kconfig option changes

* tag 'mxs-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: ocotp: Fix sparse warning
  ARM: mxs: icoll: Fix sparse warning
  ARM: mxs: mm: Fix sparse warning
  ARM: mxs_defconfig: Make USB host functional again
Signed-off-by: Olof Johansson <olof@lixom.net>

From Shawn Guo:
The imx fixes for 3.9:
 - move early resume code out of .data section to fix allyesconfig
   failure since c08e20d2 (arm: Add v7_invalidate_l1 to cache-v7.S)
   gets merged
 - Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1

* tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1
  ARM: mach-imx: move early resume code out of the .data section
Signed-off-by: Olof Johansson <olof@lixom.net>

Remove duplicate smp_twd clocks as these clocks are accessed using
DT now.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.

This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

commit 5f300acd
(ARM: 7152/1: distclean: Remove generated .dtb files)
ensured that dtbs were cleaned up when they were in
arch/arm/boot.
However, with the following commit:
commit 499cd829
(ARM: dt: change .dtb build rules to build in dts directory)

make clean now leaves dtbs in arch/arm/boot/dts/
untouched. Include dts directory so that clean-files rule
from arch/arm/boot/dts/Makefile is invoked when make
clean is done.

Cc: Dirk Behme <dirk.behme@de.bosch.com>
CC: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.

Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

In b1cffebf (ARM: GIC: remove direct use of gic_raise_softirq)
gic_raise_softirq() was moved inside arch/arm/common/gic.c but in the
process it reverted by mistake a change to that function made by
384a2902 (ARM: gic: use a private mapping for CPU target interfaces).
This breaks multicluster systems on ARM.

This patch fixes the typo.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Commit bbd707ac {ARM: omap2: use machine specific hook for late init}
accidentally added two declarations for omap4430_init_late().

Remove the duplicate declaration.

Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed because the omap_mux_get_by_name()
function calls the _omap_mux_get_by_name subfunction
for each mux partition until needed mux is not found.
As a result, we get messages like
"Could not find signal XXX" for each partition
where this mux name does not exist.

This patch fixes wrong error message in
the _omap_mux_get_by_name() function moving it
to the omap_mux_get_by_name() one and as result
reduces noise in the kernel log.

My kernel log without this patch:
[...]
[    0.221801] omap_mux_init: Add partition: #2: wkup, flags: 3
[    0.222045] _omap_mux_get_by_name: Could not find signal fref_clk0_out.sys_drm_msecure
[    0.222137] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.222167] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.270111] _omap_mux_get_by_name: Could not find signal fref_clk4_out.fref_clk4_out
[    0.273406] twl: not initialized

[...]

My kernel log with this patch:
[...]
[    0.221771] omap_mux_init: Add partition: #2: wkup, flags: 3
[    0.222106] omap_mux_get_by_name: Could not find signal sys_nirq
[    0.224945] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.274536] twl: not initialized
[...]
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP's debugfs interface creates one file
for each signal in the mux table, such file
provides a read method but didn't provide
read permission. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We should not select drivers from kconfig as they should by default
be optional. Otherwise we'll be chasing broken dependencies forever:

warning: (MACH_OMAP_ZOOM2 && MACH_OMAP_ZOOM3 && MWAVE) selects SERIAL_8250
which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS)

Fix the issue by removing the selects for zoom and add them to
omap2plus_defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The .init_late callback for OMAP3 has been missing for DT
builds, which causes a lot of late PM initializations to
be missed in turn.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:

arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...

This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include <mach/common.h> header to fix the following sparse warning:

arch/arm/mach-mxs/ocotp.c:33:11: warning: symbol 'mxs_get_ocotp' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Fix the following sparse warning:

arch/arm/mach-mxs/icoll.c:103:13: warning: symbol 'icoll_of_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Include <mach/common.h> header to fix the following sparse warnings:

arch/arm/mach-mxs/mm.c:43:13: warning: symbol 'mx23_map_io' was not declared. Should it be static?
arch/arm/mach-mxs/mm.c:48:13: warning: symbol 'mx28_map_io' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

commit 09f6ffde (USB: EHCI: fix build error by making ChipIdea host a normal
EHCI driver) introduced CONFIG_USB_EHCI_HCD as a dependency for USB_CHIPIDEA_HOST.

Select CONFIG_USB_EHCI_HCD, so that USB host can be functional again.

Cc: <stable@vger.kernel.org> # 3.8
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21
should be 545, while 543 is IPU_CSI0_D_3.  Along with the change,
one duplication of DISP1_DAT_0 in disp1-grp1 is removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>