Since commit 913a956c ("pinctrl: stm32: use dynamic allocation
of GPIO base"), it's impossible to retrieve gpios from phandle,
for example, mmc driver can't retrieve cd-gpios.
Add missing gpio-ranges properties to fix it.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The "regulator-active-discharge" property is uint32, not boolean:

  stm32mp157c-emsbc-argon.dtb: stpmic@33: regulators:pwr_sw1:regulator-active-discharge: True is not of type 'array'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The STPMIC1 PMIC vref_ddr regulator does not support over-current
protection, according to bindings and Linux driver:

  stm32mp157c-emsbc-argon.dtb: stpmic@33: regulators:vref_ddr: 'regulator-over-current-protection' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix dts check warnings on stm32mp15-scmi reported by
arm,scmi.yaml.
Signed-off-by: Pascal Paillet <p.paillet@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.

Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"

Fixes: 6257dfc1 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.

Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"

Fixes: 6257dfc1 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.

Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"

Fixes: 6257dfc1 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.

Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"

Fixes: 6257dfc1 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

This commit introduces Power over Data Line (PoDL) Power Source
Equipment (PSE) regulator nodes to the PRTT1C devicetree. The addition
of these nodes enables support for PoDL in PRTT1C devices, allowing
power delivery and data transmission over a single twisted pair.

The new PoDL PSE regulator nodes provide voltage capability information
of the current board design, which can be used as a hint for system
administrators when configuring and managing power settings. This
update enhances the versatility and simplifies the power management of
PRTT1C devices while ensuring compatibility with connected Powered
Devices (PDs).

After applying this patch, the power delivery can be controlled from
user space with a patched [1] ethtool version using the following commands:
  ethtool --set-pse t1l2 podl-pse-admin-control enable
to enable power delivery, and
  ethtool --show-pse t1l2
to display the PoDL PSE settings.

By integrating PoDL PSE support into the PRTT1C devicetree, users can
benefit from streamlined power and data connections in their
deployments, improving overall system efficiency and reducing cabling
complexity.

[1] https://lore.kernel.org/all/20230317093024.1051999-1-o.rempel@pengutronix.de/Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The patch adds support for touchscreen on the stm32f746-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add pin configurations for using i2c3 controller on stm32f7.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The revert commit 36a6418b ("Revert "ARM: dts: stm32: add CAN support
on stm32f746"") prevented parsing errors due to the lack of CAN3 binding.

Now that the binding definition for CAN3 is available in the mainline
thanks to commit 8f3ef556 ("dt-bindings: mfd: stm32f7: Add binding
definition for CAN3"), we can re-add the CAN support and make the driver
usable again.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

All boards using the DSI node duplicate the same pattern common pattern
in board DTs, that pattern is ports with endpoint labels and the same
in-SoC regulator connection. Move that common pattern into stm32mp157.dtsi
instead.

The two boards which do define panel@0 directly in the DSI bridge node now
have #address-cells/#size-cells in their board DT instead of it being in
stm32mp157.dtsi and activated incorrectly for all boards, even the ones
which use e.g. another DSI-to-something bridge.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Raphaël Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Enables use of GIC PPI#15 for OP-TEE asynchronous notifications
on stm32mp13 platforms.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The Linux Automation Test Automation Controller (LXA TAC)[1] is an embedded
software development tool built around the Octavo Systems OSD32MP15x SiP.

The device contains an eMMC for storage, a DSA-capable on board ethernet
switch with two external ports, dual CAN busses, a power switch to turn
a device under test on or off and some other I/O.

As of now there are two STM32MP157 based hardware generations (Gen 1 and
Gen 2) that have most of their hardware config in common.
In the future there will also be a STM32MP153 based hardware generation.

[1]: https://www.linux-automation.com/en/products/lxa-tac.htmlSigned-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add DT compatible string for Linux Automation GmbH Test Automation
Controllers (LXA TAC).
LXA TACs are a development tool for embedded devices with a focus on
embedded Linux devices.

As of now there are two STM32MP157 based hardware generations (Gen 1 and
Gen 2) that have most of their hardware config in common.
In the future there will also be a STM32MP153 based hardware generation.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add pinmux groups required for the Linux Automation GmbH TAC.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The ksz switch driver allows specifying an interrupt line to prevent
having to periodically poll the switch for link ups/downs and other
asynchronous events.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

This allows the usage of properties like termination-gpios and
termination-ohms, which are specified in can-controller.yaml
but were previously not usable due to additionalProperties: false.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Suggested-by: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

CFG_STM32MP1_SCMI_SHM_SYSRAM will be disabled by default for STM32MP13x
SoCs in future OP-TEE version and the OP-TEE SMCI server uses only
the OP-TEE native shared memory registered by clients.

To be compatible by default with this configuration this patch removes
the shared memory in the SCMI configuration and the associated reserved
memory in SRAM.

Fixes: 9005aeddd9fc ("ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP13")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Since the OP-TEE commit "plat-stm32mp1: scmi_server: default use OP-TEE
shared memory", integrated in OP-TEE 3.22.0-rc1, the default configuration
for STM32MP15x SoCs changes and CFG_STM32MP1_SCMI_SHM_SYSRAM is disabled
by default and the OP-TEE SMCI server uses OP-TEE native shared memory
registered by clients.

To be compatible with this configuration and the next OP-TEE versions,
this patch removes in the STM32MP15 SCMI device tree the SHMEM used by
OP-TEE SCMI and the associated reserved memory in the last 4KByte page
of SRAM.

Fixes: ea3414e1249e ("ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool

Pull irq update from Borislav Petkov:

 - Optimize IRQ domain's name assignment

* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Use return value of strreplace()

Pull x86 fpu fix from Borislav Petkov:

 - Do FPU AP initialization on Xen PV too which got missed by the recent
   boot reordering work

* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/xen: Fix secondary processors' FPU initialization

Pull x86 fix from Thomas Gleixner:
 "A single fix for the mechanism to park CPUs with an INIT IPI.

  On shutdown or kexec, the kernel tries to park the non-boot CPUs with
  an INIT IPI. But the same code path is also used by the crash utility.
  If the CPU which panics is not the boot CPU then it sends an INIT IPI
  to the boot CPU which resets the machine.

  Prevent this by validating that the CPU which runs the stop mechanism
  is the boot CPU. If not, leave the other CPUs in HLT"

* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Don't send INIT to boot CPU

Pull MIPS fixes from Thomas Bogendoerfer:

 - fixes for KVM

 - fix for loongson build and cpu probing

 - DT fixes

* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
  MIPS: dts: add missing space before {
  MIPS: Loongson: Fix build error when make modules_install
  MIPS: KVM: Fix NULL pointer dereference
  MIPS: Loongson: Fix cpu_probe_loongson() again

Pull xfs fix from Darrick Wong:
 "Nothing exciting here, just getting rid of a gcc warning that I got
  tired of seeing when I turn on gcov"

* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix uninit warning in xfs_growfs_data

Pull more smb client updates from Steve French:

 - fix potential use after free in unmount

 - minor cleanup

 - add worker to cleanup stale directory leases

* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Add a laundromat thread for cached directories
  smb: client: remove redundant pointer 'server'
  cifs: fix session state transition to avoid use-after-free issue

Pull NTB updates from Jon Mason:
 "Fixes for pci_clean_master, error handling in driver inits, and
  various other issues/bugs"

* tag 'ntb-6.5' of https://github.com/jonmason/ntb:
  ntb: hw: amd: Fix debugfs_create_dir error checking
  ntb.rst: Fix copy and paste error
  ntb_netdev: Fix module_init problem
  ntb: intel: Remove redundant pci_clear_master
  ntb: epf: Remove redundant pci_clear_master
  ntb_hw_amd: Remove redundant pci_clear_master
  ntb: idt: drop redundant pci_enable_pcie_error_reporting()
  MAINTAINERS: git://github -> https://github.com for jonmason
  NTB: EPF: fix possible memory leak in pci_vntb_probe()
  NTB: ntb_tool: Add check for devm_kcalloc
  NTB: ntb_transport: fix possible memory leak while device_register() fails
  ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
  NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
  ntb: idt: Fix error handling in idt_pci_driver_init()

Lockdep is certainly right to complain about

  (&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f
                 but task is already holding lock:
  (&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db

Invert those to the usual ordering.

Fixes: 33313a74 ("mm: lock newly mapped VMA which can be modified after it becomes visible")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull hotfixes from Andrew Morton:
 "16 hotfixes. Six are cc:stable and the remainder address post-6.4
  issues"

The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.

* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  lib: dhry: fix sleeping allocations inside non-preemptable section
  kasan, slub: fix HW_TAGS zeroing with slub_debug
  kasan: fix type cast in memory_is_poisoned_n
  mailmap: add entries for Heiko Stuebner
  mailmap: update manpage link
  bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
  MAINTAINERS: add linux-next info
  mailmap: add Markus Schneider-Pargmann
  writeback: account the number of pages written back
  mm: call arch_swap_restore() from do_swap_page()
  squashfs: fix cache race with migration
  mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
  docs: update ocfs2-devel mailing list address
  MAINTAINERS: update ocfs2-devel mailing list address
  mm: disable CONFIG_PER_VMA_LOCK until its fixed
  fork: lock VMAs of the parent process when forking

When forking a child process, the parent write-protects anonymous pages
and COW-shares them with the child being forked using copy_present_pte().

We must not take any concurrent page faults on the source vma's as they
are being processed, as we expect both the vma and the pte's behind it
to be stable.  For example, the anon_vma_fork() expects the parents
vma->anon_vma to not change during the vma copy.

A concurrent page fault on a page newly marked read-only by the page
copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the
source vma, defeating the anon_vma_clone() that wasn't done because the
parent vma originally didn't have an anon_vma, but we now might end up
copying a pte entry for a page that has one.

Before the per-vma lock based changes, the mmap_lock guaranteed
exclusion with concurrent page faults.  But now we need to do a
vma_start_write() to make sure no concurrent faults happen on this vma
while it is being processed.

This fix can potentially regress some fork-heavy workloads.  Kernel
build time did not show noticeable regression on a 56-core machine while
a stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~5% regression.  If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance.  Further
optimizations are possible if this regression proves to be problematic.
Suggested-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624
Fixes: 0bff0aae ("x86/mm: try VMA lock-based page fault handling first")
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmap_region adds a newly created VMA into VMA tree and might modify it
afterwards before dropping the mmap_lock.  This poses a problem for page
faults handled under per-VMA locks because they don't take the mmap_lock
and can stumble on this VMA while it's still being modified.  Currently
this does not pose a problem since post-addition modifications are done
only for file-backed VMAs, which are not handled under per-VMA lock.
However, once support for handling file-backed page faults with per-VMA
locks is added, this will become a race.

Fix this by write-locking the VMA before inserting it into the VMA tree.
Other places where a new VMA is added into VMA tree do not modify it
after the insertion, so do not need the same locking.

Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With recent changes necessitating mmap_lock to be held for write while
expanding a stack, per-VMA locks should follow the same rules and be
write-locked to prevent page faults into the VMA being expanded. Add
the necessary locking.

Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more SCSI updates from James Bottomley:
 "A few late arriving patches that missed the initial pull request. It's
  mostly bug fixes (the dt-bindings is a fix for the initial pull)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: core: Remove unused function declaration
  scsi: target: docs: Remove tcm_mod_builder.py
  scsi: target: iblock: Quiet bool conversion warning with pr_preempt use
  scsi: dt-bindings: ufs: qcom: Fix ICE phandle
  scsi: core: Simplify scsi_cdl_check_cmd()
  scsi: isci: Fix comment typo
  scsi: smartpqi: Replace one-element arrays with flexible-array members
  scsi: target: tcmu: Replace strlcpy() with strscpy()
  scsi: ncr53c8xx: Replace strlcpy() with strscpy()
  scsi: lpfc: Fix lpfc_name struct packing

Pull more i2c updates from Wolfram Sang:

 - xiic patch should have been in the original pull but slipped through

 - mpc patch fixes a build regression

 - nomadik cleanup

* tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mpc: Drop unused variable
  i2c: nomadik: Remove a useless call in the remove function
  i2c: xiic: Don't try to handle more interrupt events after error

Pull hardening fixes from Kees Cook:

 - Check for NULL bdev in LoadPin (Matthias Kaehlcke)

 - Revert unwanted KUnit FORTIFY build default

 - Fix 1-element array causing boot warnings with xhci-hub

* tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array
  Revert "fortify: Allow KUnit test to build without FORTIFY"
  dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter

The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>