Add support for XDP PASS, DROP and TX actions.

This patch contains the following changes:
1) Support installing/uninstalling XDP program
2) Add dedicated XDP TX queues
3) Add support for XDP DROP action
4) Add support for XDP TX action
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes to enable adding and removing TX queues without calling
gve_close() and gve_open().

Made the following changes:
1) priv->tx, priv->rx and priv->qpls arrays are allocated based on
   max tx queues and max rx queues
2) Changed gve_adminq_create_tx_queues(), gve_adminq_destroy_tx_queues(),
gve_tx_alloc_rings() and gve_tx_free_rings() functions to add/remove a
subset of TX queues rather than all the TX queues.
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds/modifies helper functions needed to add XDP
support.
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: annotate lockless accesses to sk_err[_soft]

This patch series is inspired by yet another syzbot report.

Most poll() handlers are lockless and read sk->sk_err
while other cpus can change it.

Add READ_ONCE/WRITE_ONCE() to major/usual offenders.

More to come later.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

unix_poll() and unix_dgram_poll() read sk->sk_err
without any lock held.

Add relevant READ_ONCE()/WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp_poll() reads sk->sk_err without socket lock held/owned.

Add READ_ONCE() and WRITE_ONCE() to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_poll() reads sk->sk_err without socket lock held/owned.

We should used READ_ONCE() here, and update writers
to use WRITE_ONCE().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field can be read/written without lock synchronization.

tcp and dccp have been handled in different patches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field can be read/written without lock synchronization.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field can be read/written without lock synchronization.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting timestamp filter was explicitly disabled on vlan devices in
containers because it might affect other processes on the host. But it's
absolutely legit in case when real device is in the same namespace.

Fixes: 873017af ("vlan: disable SIOCSHWTSTAMP in container")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King (Oracle) says:

====================
Minor fixes for pcs_get_state() implementations

This series contains a number fixes for minor issues with some
pcs_get_state() implementations, particualrly for the phylink
state->an_enabled member. As they are minor, I'm suggesting we
queue them in net-next as there is follow-on work for these, and
there is no urgency for them to be in -rc.

Just like phylib, state->advertising's Autoneg bit is a copy of
state->an_enabled, and thus it is my intention to remove
state->an_enabled from phylink to simplify things.

This series gets rid of state->an_enabled assignments or
reporting that should never have been there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

an_enabled will be going away, and in any case, pcs_get_state() should
not be updating this member. Remove the print.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phylink does not want the current state of the link when reading the
PCS link state - it wants the latched state. Don't double-read the
MII status register. Phylink will re-read as necessary to capture
transient link-down events as of dbae3388 ("net: phylink: Force
retrigger in case of latched link-fail indicator").

The above referenced commit is a dependency for this change, and thus
this change should not be backported to any kernel that does not
contain the above referenced commit.

Fixes: fcb26bd2 ("net: phy: Add Synopsys DesignWare XPCS MDIO module")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
vxlan: Add MDB support

tl;dr
=====

This patchset implements MDB support in the VXLAN driver, allowing it to
selectively forward IP multicast traffic to VTEPs with interested
receivers instead of flooding it to all the VTEPs as BUM. The motivating
use case is intra and inter subnet multicast forwarding using EVPN
[1][2], which means that MDB entries are only installed by the user
space control plane and no snooping is implemented, thereby avoiding a
lot of unnecessary complexity in the kernel.

Background
==========

Both the bridge and VXLAN drivers have an FDB that allows them to
forward Ethernet frames based on their destination MAC addresses and
VLAN/VNI. These FDBs are managed using the same PF_BRIDGE/RTM_*NEIGH
netlink messages and bridge(8) utility.

However, only the bridge driver has an MDB that allows it to selectively
forward IP multicast packets to bridge ports with interested receivers
behind them, based on (S, G) and (*, G) MDB entries. When these packets
reach the VXLAN driver they are flooded using the "all-zeros" FDB entry
(00:00:00:00:00:00). The entry either includes the list of all the VTEPs
in the tenant domain (when ingress replication is used) or the multicast
address of the BUM tunnel (when P2MP tunnels are used), to which all the
VTEPs join.

Networks that make heavy use of multicast in the overlay can benefit
from a solution that allows them to selectively forward IP multicast
traffic only to VTEPs with interested receivers. Such a solution is
described in the next section.

Motivation
==========

RFC 7432 [3] defines a "MAC/IP Advertisement route" (type 2) [4] that
allows VTEPs in the EVPN network to advertise and learn reachability
information for unicast MAC addresses. Traffic destined to a unicast MAC
address can therefore be selectively forwarded to a single VTEP behind
which the MAC is located.

The same is not true for IP multicast traffic. Such traffic is simply
flooded as BUM to all VTEPs in the broadcast domain (BD) / subnet,
regardless if a VTEP has interested receivers for the multicast stream
or not. This is especially problematic for overlay networks that make
heavy use of multicast.

The issue is addressed by RFC 9251 [1] that defines a "Selective
Multicast Ethernet Tag Route" (type 6) [5] which allows VTEPs in the
EVPN network to advertise multicast streams that they are interested in.
This is done by having each VTEP suppress IGMP/MLD packets from being
transmitted to the NVE network and instead communicate the information
over BGP to other VTEPs.

The draft in [2] further extends RFC 9251 with procedures to allow
efficient forwarding of IP multicast traffic not only in a given subnet,
but also between different subnets in a tenant domain.

The required changes in the bridge driver to support the above were
already merged in merge commit 8150f0cf ("Merge branch
'bridge-mcast-extensions-for-evpn'"). However, full support entails MDB
support in the VXLAN driver so that it will be able to selectively
forward IP multicast traffic only to VTEPs with interested receivers.
The implementation of this MDB is described in the next section.

Implementation
==============

The user interface is extended to allow user space to specify the
destination VTEP(s) and related parameters. Example usage:

 # bridge mdb add dev vxlan0 port vxlan0 grp 239.1.1.1 permanent dst 198.51.100.1
 # bridge mdb add dev vxlan0 port vxlan0 grp 239.1.1.1 permanent dst 192.0.2.1

 $ bridge -d -s mdb show
 dev vxlan0 port vxlan0 grp 239.1.1.1 permanent filter_mode exclude proto static dst 192.0.2.1    0.00
 dev vxlan0 port vxlan0 grp 239.1.1.1 permanent filter_mode exclude proto static dst 198.51.100.1    0.00

Since the MDB is fully managed by user space and since snooping is not
implemented, only permanent entries can be installed and temporary
entries are rejected by the kernel.

The netlink interface is extended with a few new attributes in the
RTM_NEWMDB / RTM_DELMDB request messages:

[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
	struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
	[ MDBE_ATTR_SOURCE ]
		struct in_addr / struct in6_addr
	[ MDBE_ATTR_SRC_LIST ]
		[ MDBE_SRC_LIST_ENTRY ]
			[ MDBE_SRCATTR_ADDRESS ]
				struct in_addr / struct in6_addr
		[ ...]
	[ MDBE_ATTR_GROUP_MODE ]
		u8
	[ MDBE_ATTR_RTPORT ]
		u8
	[ MDBE_ATTR_DST ]	// new
		struct in_addr / struct in6_addr
	[ MDBE_ATTR_DST_PORT ]	// new
		u16
	[ MDBE_ATTR_VNI ]	// new
		u32
	[ MDBE_ATTR_IFINDEX ]	// new
		s32
	[ MDBE_ATTR_SRC_VNI ]	// new
		u32

RTM_NEWMDB / RTM_DELMDB responses and notifications are extended with
corresponding attributes.

One MDB entry that can be installed in the VXLAN MDB, but not in the
bridge MDB is the catchall entry (0.0.0.0 / ::). It is used to transmit
unregistered multicast traffic that is not link-local and is especially
useful when inter-subnet multicast forwarding is required. See patch #12
for a detailed explanation and motivation. It is similar to the
"all-zeros" FDB entry that can be installed in the VXLAN FDB, but not
the bridge FDB.

"added_by_star_ex" entries
--------------------------

The bridge driver automatically installs (S, G) MDB port group entries
marked as "added_by_star_ex" whenever it detects that an (S, G) entry
can prevent traffic from being forwarded via a port associated with an
EXCLUDE (*, G) entry. The bridge will add the port to the port group of
the (S, G) entry, thereby creating a new port group entry. The
complexity associated with these entries is not trivial, but it needs to
reside in the bridge driver because it automatically installs MDB
entries in response to snooped IGMP / MLD packets.

The same in not true for the VXLAN MDB which is entirely managed by user
space who is fully capable of forming the correct replication lists on
its own. In addition, the complexity associated with the
"added_by_star_ex" entries in the VXLAN driver is higher compared to the
bridge: Whenever a remote VTEP is added to the catchall entry, it needs
to be added to all the existing MDB entries, as such a remote requested
all the multicast traffic to be forwarded to it. Similarly, whenever an
(*, G) or (S, G) entry is added, all the remotes associated with the
catchall entry need to be added to it.

Given the above, this patchset does not implement support for such
entries.  One argument against this decision can be that in the future
someone might want to populate the VXLAN MDB in response to decapsulated
IGMP / MLD packets and not according to EVPN routes. Regardless of my
doubts regarding this possibility, it can be implemented using a new
VXLAN device knob that will also enable the "added_by_star_ex"
functionality.

Testing
=======

Tested using existing VXLAN and MDB selftests under "net/" and
"net/forwarding/". Added a dedicated selftest in the last patch.

Patchset overview
=================

Patches #1-#3 are small preparations in the bridge driver. I plan to
submit them separately together with an MDB dump test case.

Patches #4-#6 are additional preparations centered around the extraction
of the MDB netlink handlers from the bridge driver to the common
rtnetlink code. This allows reusing the existing MDB netlink messages
for the configuration of the VXLAN MDB.

Patches #7-#9 include more small preparations in the common rtnetlink
code and the VXLAN driver.

Patch #10 implements the MDB control path in the VXLAN driver, which
will allow user space to create, delete, replace and dump MDB entries.

Patches #11-#12 implement the MDB data path in the VXLAN driver,
allowing it to selectively forward IP multicast traffic according to the
matched MDB entry.

Patch #13 finally enables MDB support in the VXLAN driver.

iproute2 patches can be found here [6].

Note that in order to fully support the specifications in [1] and [2],
additional functionality is required from the data path. However, it can
be achieved using existing kernel interfaces which is why it is not
described here.

Changelog
=========

Since v1 [7]:

Patch #9: Use htons() in 'case' instead of ntohs() in 'switch'.

Since RFC [8]:

Patch #3: Use NL_ASSERT_DUMP_CTX_FITS().
Patch #3: memset the entire context when moving to the next device.
Patch #3: Reset sequence counters when moving to the next device.
Patch #3: Use NL_SET_ERR_MSG_ATTR() in rtnl_validate_mdb_entry().
Patch #7: Remove restrictions regarding mixing of multicast and unicast
remote destination IPs in an MDB entry. While such configuration does
not make sense to me, it is no forbidden by the VXLAN FDB code and does
not crash the kernel.
Patch #7: Fix check regarding all-zeros MDB entry and source.
Patch #11: New patch.

[1] https://datatracker.ietf.org/doc/html/rfc9251
[2] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast
[3] https://datatracker.ietf.org/doc/html/rfc7432
[4] https://datatracker.ietf.org/doc/html/rfc7432#section-7.2
[5] https://datatracker.ietf.org/doc/html/rfc9251#section-9.1
[6] https://github.com/idosch/iproute2/commits/submit/mdb_vxlan_rfc_v1
[7] https://lore.kernel.org/netdev/20230313145349.3557231-1-idosch@nvidia.com/
[8] https://lore.kernel.org/netdev/20230204170801.3897900-1-idosch@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test cases for VXLAN MDB, testing the control and data paths. Two
different sets of namespaces (i.e., ns{1,2}_v4 and ns{1,2}_v6) are used
in order to test VXLAN MDB with both IPv4 and IPv6 underlays,
respectively.

Example truncated output:

 # ./test_vxlan_mdb.sh
 [...]
 Tests passed: 620
 Tests failed:   0
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the VXLAN MDB control and data paths are in place we can expose
the VXLAN MDB functionality to user space.

Set the VXLAN MDB net device operations to the appropriate functions,
thereby allowing the rtnetlink code to reach the VXLAN driver.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Integrate MDB support into the Tx path of the VXLAN driver, allowing it
to selectively forward IP multicast traffic according to the matched MDB
entry.

If MDB entries are configured (i.e., 'VXLAN_F_MDB' is set) and the
packet is an IP multicast packet, perform up to three different lookups
according to the following priority:

1. For an (S, G) entry, using {Source VNI, Source IP, Destination IP}.
2. For a (*, G) entry, using {Source VNI, Destination IP}.
3. For the catchall MDB entry (0.0.0.0 or ::), using the source VNI.

The catchall MDB entry is similar to the catchall FDB entry
(00:00:00:00:00:00) that is currently used to transmit BUM (broadcast,
unknown unicast and multicast) traffic. However, unlike the catchall FDB
entry, this entry is only used to transmit unregistered IP multicast
traffic that is not link-local. Therefore, when configured, the catchall
FDB entry will only transmit BULL (broadcast, unknown unicast,
link-local multicast) traffic.

The catchall MDB entry is useful in deployments where inter-subnet
multicast forwarding is used and not all the VTEPs in a tenant domain
are members in all the broadcast domains. In such deployments it is
advantageous to transmit BULL (broadcast, unknown unicast and link-local
multicast) and unregistered IP multicast traffic on different tunnels.
If the same tunnel was used, a VTEP only interested in IP multicast
traffic would also pull all the BULL traffic and drop it as it is not a
member in the originating broadcast domain [1].

If the packet did not match an MDB entry (or if the packet is not an IP
multicast packet), return it to the Tx path, allowing it to be forwarded
according to the FDB.

If the packet did match an MDB entry, forward it to the associated
remote VTEPs. However, if the entry is a (*, G) entry and the associated
remote is in INCLUDE mode, then skip over it as the source IP is not in
its source list (otherwise the packet would have matched on an (S, G)
entry). Similarly, if the associated remote is marked as BLOCKED (can
only be set on (S, G) entries), then skip over it as well as the remote
is in EXCLUDE mode and the source IP is in its source list.

[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-2.6Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an internal flag to indicate whether MDB entries are configured or
not. Set the flag after installing the first MDB entry and clear it
before deleting the last one.

The flag will be consulted by the data path which will only perform an
MDB lookup if the flag is set, thereby keeping the MDB overhead to a
minimum when the MDB is not used.

Another option would have been to use a static key, but it is global and
not per-device, unlike the current approach.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement MDB control path support, enabling the creation, deletion,
replacement and dumping of MDB entries in a similar fashion to the
bridge driver. Unlike the bridge driver, each entry stores a list of
remote VTEPs to which matched packets need to be replicated to and not a
list of bridge ports.

The motivating use case is the installation of MDB entries by a user
space control plane in response to received EVPN routes. As such, only
allow permanent MDB entries to be installed and do not implement
snooping functionality, avoiding a lot of unnecessary complexity.

Since entries can only be modified by user space under RTNL, use RTNL as
the write lock. Use RCU to ensure that MDB entries and remotes are not
freed while being accessed from the data path during transmission.

In terms of uAPI, reuse the existing MDB netlink interface, but add a
few new attributes to request and response messages:

* IP address of the destination VXLAN tunnel endpoint where the
  multicast receivers reside.

* UDP destination port number to use to connect to the remote VXLAN
  tunnel endpoint.

* VXLAN VNI Network Identifier to use to connect to the remote VXLAN
  tunnel endpoint. Required when Ingress Replication (IR) is used and
  the remote VTEP is not a member of originating broadcast domain
  (VLAN/VNI) [1].

* Source VNI Network Identifier the MDB entry belongs to. Used only when
  the VXLAN device is in external mode.

* Interface index of the outgoing interface to reach the remote VXLAN
  tunnel endpoint. This is required when the underlay destination IP is
  multicast (P2MP), as the multicast routing tables are not consulted.

All the new attributes are added under the 'MDBA_SET_ENTRY_ATTRS' nest
which is strictly validated by the bridge driver, thereby automatically
rejecting the new attributes.

[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-3.2.2Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Given a packet and a remote destination, the function will take care of
encapsulating the packet and transmitting it to the destination.

Expose it so that it could be used in subsequent patches by the MDB code
to transmit a packet to the remote destination(s) stored in the MDB
entry.

It will allow us to keep the MDB code self-contained, not exposing its
data structures to the rest of the VXLAN driver.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the helpers out of the core C file to the private header so that
they could be used by the upcoming MDB code.

While at it, constify the second argument of vxlan_nla_get_addr().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the upcoming VXLAN MDB implementation, the 0.0.0.0 and :: MDB entries
will act as catchall entries for unregistered IP multicast traffic in a
similar fashion to the 00:00:00:00:00:00 VXLAN FDB entry that is used to
transmit BUM traffic.

In deployments where inter-subnet multicast forwarding is used, not all
the VTEPs in a tenant domain are members in all the broadcast domains.
It is therefore advantageous to transmit BULL (broadcast, unknown
unicast and link-local multicast) and unregistered IP multicast traffic
on different tunnels. If the same tunnel was used, a VTEP only
interested in IP multicast traffic would also pull all the BULL traffic
and drop it as it is not a member in the originating broadcast domain
[1].

Prepare for this change by allowing the 0.0.0.0 group address in the
common rtnetlink MDB code and forbid it in the bridge driver. A similar
change is not needed for IPv6 because the common code only validates
that the group address is not the all-nodes address.

[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-2.6Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the bridge driver registers handlers for MDB netlink
messages, making it impossible for other drivers to implement MDB
support.

As a preparation for VXLAN MDB support, move the MDB handlers out of the
bridge driver to the core rtnetlink code. The rtnetlink code will call
into individual drivers by invoking their previously added MDB net
device operations.

Note that while the diffstat is large, the change is mechanical. It
moves code out of the bridge driver to rtnetlink code. Also note that a
similar change was made in 2012 with commit 77162022 ("net: add
generic PF_BRIDGE:RTM_ FDB hooks") that moved FDB handlers out of the
bridge driver to the core rtnetlink code.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the previously added MDB net device operations in the bridge
driver so that they could be invoked by core rtnetlink code in the next
patch.

The operations are identical to the existing br_mdb_{dump,add,del}
functions. The '_new' suffix will be removed in the next patch. The
functions are re-implemented in this patch to make the conversion in the
next patch easier to review.

Add dummy implementations when 'CONFIG_BRIDGE_IGMP_SNOOPING' is
disabled, so that an error will be returned to user space when it is
trying to add or delete an MDB entry. This is consistent with existing
behavior where the bridge driver does not even register rtnetlink
handlers for RTM_{NEW,DEL,GET}MDB messages when this Kconfig option is
disabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MDB net device operations that will be invoked by rtnetlink code in
response to received RTM_{NEW,DEL,GET}MDB messages. Subsequent patches
will implement these operations in the bridge and VXLAN drivers.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Siddharth Vadapalli says:

====================
Add J784S4 CPSW9G NET Bindings

This series cleans up the bindings by reordering the compatibles, followed
by adding the bindings for CPSW9G instance of CPSW Ethernet Switch on TI's
J784S4 SoC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update bindings for TI K3 J784S4 SoC which contains 9 ports (8 external
ports) CPSW9G module and add compatible for it.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reorder compatibles to follow alphanumeric order.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extended performance counter stats in 'ethtool -S <interface>' output
for MANA VF to facilitate troubleshooting.

Tested-on: Ubuntu22
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ngbe and txgbe ndo_change_mtu support.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rtl8365mb was using a fixed MTU size of 1536, which was probably
inspired by the rtl8366rb's initial frame size. However, unlike that
family, the rtl8365mb family can specify the max frame size in bytes,
rather than in fixed steps.

DSA calls change_mtu for the CPU port once the max MTU value among the
ports changes. As the max frame size is defined globally, the switch
is configured only when the call affects the CPU port.

The available specifications do not directly define the max supported
frame size, but it mentions a 16k limit. This driver will use the 0x3FFF
limit as it is used in the vendor API code. However, the switch sets the
max frame size to 16368 bytes (0x3FF0) after it resets.

change_mtu uses MTU size, or ethernet payload size, while the switch
works with frame size. The frame size is calculated considering the
ethernet header (14 bytes), a possible 802.1Q tag (4 bytes), the payload
size (MTU), and the Ethernet FCS (4 bytes). The CPU tag (8 bytes) is
consumed before the switch enforces the limit.

During setup, the driver will use the default 1500-byte MTU of DSA to
set the maximum frame size. The current sum will be
VLAN_ETH_HLEN+1500+ETH_FCS_LEN, which results in 1522 bytes.  Although
it is lower than the previous initial value of 1536 bytes, the driver
will increase the frame size for a larger MTU. However, if something
requires more space without increasing the MTU, such as QinQ, we would
need to add the extra length to the rtl8365mb_port_change_mtu() formula.

MTU was tested up to 2018 (with 802.1Q) as that is as far as mt7620
(where rtl8367s is stacked) can go. The register was manually
manipulated byte-by-byte to ensure the MTU to frame size conversion was
correct. For frames without 802.1Q tag, the frame size limit will be 4
bytes over the required size.

There is a jumbo register, enabled by default at 6k frame size.
However, the jumbo settings do not seem to limit nor expand the maximum
tested MTU (2018), even when jumbo is disabled. More tests are needed
with a device that can handle larger frames.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Durai Manickam says:

====================
Add PTP support for sama7g5

This patch series is intended to add PTP capability to the GEM and
EMAC for sama7g5.
====================

Link: https://lore.kernel.org/r/20230315095053.53969-1-durai.manickamkr@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add PTP capability to the Ethernet MAC.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add PTP capability to the Gigabit Ethernet MAC.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20230314181824.56881-1-andriy.shevchenko@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are no users of nfcmrvl platform_data struct outside of the
driver and none will be added, so move it into the driver.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GPY2xx devices need 3 seconds to fully switch out of loopback mode
before it can safely re-enter loopback mode. Implement timeout mechanism
to guarantee 3 seconds waited before re-enter loopback mode.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a pr_warn_ratelimited message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20230314082315.26532-1-colin.i.king@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>