Define the SILK board dependent part of the SDHI1 (connected to micro-SD
slot) device nodes along with the necessary voltage regulators.

Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car M2-W does not have an IMP core or an IMP clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car E2 does not have an IMP core or an IMP clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable HS-USB device  for the Porter board, defining the GPIO that the
driver should check  when probing (which is the ID output from MAX3355
OTG chip).

Note that there  will be pinctrl-related error messages if both internal
PCI  and  HS-USB drivers are enabled but they should be just ignored.

This patch is  analogous  to the commit 6f4f7156 ("ARM: shmobile:
henninger: enable HS-USB") as there  are no differences between the
boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable  internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable  USB PHY device  for the Porter board.  We have to
enable  everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the PCIe controller and clock for the Porter board.

This patch is analogous to the commit 485f3ce6 ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the QSPI device node.
Add device nodes  for Spansion  S25FL512S SPI flash and the MTD partitions
on it.

This patch is  mostly analogous  to the commit f59838d4 ("ARM:
shmobile: henninger: add QSPI DT support")  as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the  Porter board dependent part of the VIN0 device node.
Add the device node for Analog Devices  ADV7180 video decoder to I2C2 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.

This patch is  analogous to the commit 8d62f4f7 ("ARM: shmobile:
henninger: add VIN0/ADV7180 DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the I2C2 device node.

This patch is  analogous to the commit 29a647c3 ("ARM: shmobile:
henninger: add I2C2 DT support") as there are no differences between
the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable SATA0 device for the Porter board.

This patch is analogous to the commit 5a62ec57 ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the SDHI0/2 device nodes along
with the  necessary  voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...

This patch is analogous to the commit 1299df03 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there  are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define  the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.

This  patch  is analogous to the commit 26b0d2cf ("ARM: shmobile:
henninger: add Ether DT support") as there  are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Unfortunately, the SILK board bindings were not quite correct, as the  board
name should be all caps.  Fix that,  adding the board model #  in parens and
removing stray semicolon.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the R8A7794 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Mitsubishi AA121TD01 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the SILK board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the R8A7794 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which  is a  slightly modified version  of the Henninger board).

SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Porter device tree bindings documentation, listing it as a supported board.

This allows to use checkpatch to validate DTSes referring to the Porter board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add device nodes for the R8A7794 internal PCI bridge devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

It seems we used to rely on the default pinmux setting of this HW, but
currently we need to explicitly set the pinmux to access this bus. It is
better style, too.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Because of historical reason, audio clock didn't use CCF.
Let's use it now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Because of historical reason, audio clock didn't use CCF.
Let's use it now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define  the  SILK board dependent part of the  VIN0  device  node.
Add the device node for Analog Devices ADV7180 video decoder to I2C1 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.

Based on the Henninger VIN0/ADV8170 device tree patch by myself.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7794 part of the VIN[01] device nodes. Add aliases for
the VIN[01] device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SILK board dependent part of the I2C1 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7794 parts of the I2C[0-5] device nodes.

Based on the original patch by Koji Matsuoka <koji.matsuoka.xm@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Replace the deprecated generic "adi,adxl34x" compatible value by the
adxl345-specific "adi,adxl345" value, cfr. commit e465bf6f ("DT:
i2c: Deprecate adi,adxl34x compatible string").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Convert Marzen to use board-specific serial0 and serial1 instead
of the older shared SoC-specific SCIF index.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SILK board dependent part of the QSPI device node.
Add device nodes  for Spansion  S25FL512S SPI flash and MTD partitions on it.

Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7794 part of the QSPI device node.

Based on original patch by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe GPIO[0-6] controllers in the R8A7794 device tree.

Based on original patch by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the GPIO clocks in the R8A7794 device tree.

Based on the original patch by Koji Matsuoka <koji.matsuoka.xm@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Silk Device tree bindings Documentation, listing it as a supported board.

This allows to use checkpatch to validate DTSes referring to the Silk board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>

The shmobile_clk_init() function has been removed and the linux/sh_clk.h
header doesn't need to be included anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>