- 20 Jun, 2017 40 commits
-
-
Al Viro authored
commit c0cf3ef5 upstream. What matters when deciding if we should make a page uptodate is not how much we _wanted_ to copy, but how much we actually have copied. As it is, on architectures that do not zero tail on short copy we can leave uninitialized data in page marked uptodate. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Willy Tarreau <w@1wt.eu>
-
Ilya Dryomov authored
commit 5c056fdc upstream. After sending an authorizer (ceph_x_authorize_a + ceph_x_authorize_b), the client gets back a ceph_x_authorize_reply, which it is supposed to verify to ensure the authenticity and protect against replay attacks. The code for doing this is there (ceph_x_verify_authorizer_reply(), ceph_auth_verify_authorizer_reply() + plumbing), but it is never invoked by the the messenger. AFAICT this goes back to 2009, when ceph authentication protocols support was added to the kernel client in 4e7a5dcd ("ceph: negotiate authentication protocol; implement AUTH_NONE protocol"). The second param of ceph_connection_operations::verify_authorizer_reply is unused all the way down. Pass 0 to facilitate backporting, and kill it in the next commit. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Gerald Schaefer authored
commit 5457e03d upstream. The buffer for iucv_message_receive() needs to be below 2 GB. In __iucv_message_receive(), the buffer address is casted to an u32, which would result in either memory corruption or an addressing exception when using addresses >= 2 GB. Fix this by using GFP_DMA for the buffer allocation. Signed-off-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Martin K. Petersen authored
commit 7c856152 upstream. We previously made sure that the reported disk capacity was less than 0xffffffff blocks when the kernel was not compiled with large sector_t support (CONFIG_LBDAF). However, this check assumed that the capacity was reported in units of 512 bytes. Add a sanity check function to ensure that we only enable disks if the entire reported capacity can be expressed in terms of sector_t. Reported-by:
Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by:
Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Martin K. Petersen authored
commit a00a7862 upstream. Kefeng Wang discovered that old versions of the QEMU CD driver would return mangled mode data causing us to walk off the end of the buffer in an attempt to parse it. Sanity check the returned mode sense data. Reported-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by:
-
Anton Blanchard authored
commit 85e8a239 upstream. We see lpfc devices regularly fail during kexec. Fix this by adding a shutdown method which mirrors the remove method. Signed-off-by:
Anton Blanchard <anton@samba.org> Reviewed-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by:
-
Nicholas Bellinger authored
commit a04e54f2 upstream. The following fixes a divide by zero OOPs with TYPE_TAPE due to pscsi_tape_read_blocksize() failing causing a zero sd->sector_size being propigated up via dev_attrib.hw_block_size. It also fixes another long-standing bug where TYPE_TAPE and TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(), which does not call scsi_device_get() to take the device reference. Instead, rename pscsi_create_type_rom() to pscsi_create_type_nondisk() and use it for all cases. Finally, also drop a dump_stack() in pscsi_get_blocks() for non TYPE_DISK, which in modern target-core can get invoked via target_sense_desc_format() during CHECK_CONDITION. [js] cast max_sectors to unsigned to avoid warnings Reported-by:
Malcolm Haak <insanemal@gmail.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Long Li authored
commit 40630f46 upstream. On I/O errors, the Windows driver doesn't set data_transfer_length on error conditions other than SRB_STATUS_DATA_OVERRUN. In these cases we need to set data_transfer_length to 0, indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN, data_transfer_length is set by the Windows driver to the actual data transferred. Reported-by:
Shiva Krishna <Shiva.Krishna@nimblestorage.com> Signed-off-by:
Long Li <longli@microsoft.com> Reviewed-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Long Li authored
commit bba5dc33 upstream. When sense message is present on error, we should pass along to the upper layer to decide how to deal with the error. This patch fixes connectivity issues with Fiber Channel devices. Signed-off-by:
-
Johannes Thumshirn authored
commit fd3fc0b4 upstream. Don't crash the machine just because of an empty transfer. Use WARN_ON() combined with returning an error. Found by Dmitry Vyukov and syzkaller. [ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON() might still be a cause of excessive log spamming. NOTE! If this warning ever triggers, we may end up leaking resources, since this doesn't bother to try to clean the command up. So this WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is much worse. People really need to stop using BUG_ON() for "this shouldn't ever happen". It makes pretty much any bug worse. - Linus ] Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: James Bottomley <jejb@linux.vnet.ibm.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Christoph Hellwig authored
commit 635d98b1 upstream. scsi_init_io should only be called for requests that transfer data, so move the assert that a request has segments from the callers into scsi_init_io. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Wei Fang authored
commit d2a14525 upstream. A race between scanning and fc_remote_port_delete() may result in a permanent stop if the device gets blocked before scsi_sysfs_add_sdev() and unblocked after. The reason is that blocking a device sets both the SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However, scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the device to be ignored by scsi_target_unblock() and thus never have its QUEUE_FLAG_STOPPED cleared leading to a device which is apparently running but has a stopped queue. We actually have two places where SDEV_RUNNING is set: once in scsi_add_lun() which respects the blocked flag and once in scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely spurious, simply remove it to fix the problem. Reported-by:
Zengxi Chen <chenzengxi@huawei.com> Signed-off-by:
Wei Fang <fangwei1@huawei.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Russell Currey authored
commit 298360af upstream. ast_get_dram_info() configures a window in order to access BMC memory. A BMC register can be configured to disallow this, and if so, causes an infinite loop in the ast driver which renders the system unusable. Fix this by erroring out if an error is detected. On powerpc systems with EEH, this leads to the device being fenced and the system continuing to operate. Signed-off-by:
Russell Currey <ruscur@russell.cc> Reviewed-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161215051241.20815-1-ruscur@russell.ccSigned-off-by:
-
Larry Finger authored
commit 8052d724 upstream. When there is a CRC error in the SPROM read from the device, the code attempts to handle a fallback SPROM. When this also fails, the driver returns zero rather than an error code. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Darrick J. Wong authored
commit 2aa6ba7b upstream. If we try to allocate memory pages to back an xfs_buf that we're trying to read, it's possible that we'll be so short on memory that the page allocation fails. For a blocking read we'll just wait, but for readahead we simply dump all the pages we've collected so far. Unfortunately, after dumping the pages we neglect to clear the _XBF_PAGES state, which means that the subsequent call to xfs_buf_free thinks that b_pages still points to pages we own. It then double-frees the b_pages pages. This results in screaming about negative page refcounts from the memory manager, which xfs oughtn't be triggering. To reproduce this case, mount a filesystem where the size of the inodes far outweighs the availalble memory (a ~500M inode filesystem on a VM with 300MB memory did the trick here) and run bulkstat in parallel with other memory eating processes to put a huge load on the system. The "check summary" phase of xfs_scrub also works for this purpose. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by:
Eric Sandeen <sandeen@redhat.com> Cc: Ivan Kozik <ivan@ludios.org> Signed-off-by:
-
Eric Sandeen authored
commit 6b10b23c upstream. xlog_recover_clear_agi_bucket didn't set the type to XFS_BLFT_AGI_BUF, so we got a warning during log replay (or an ASSERT on a debug build). XFS (md0): Unknown buffer type 0! XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1 Fix this, as was done in f19b872b for 2 other locations with the same problem. Signed-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Julien Grall authored
commit 24d5373d upstream. The function xen_guest_init is using __alloc_percpu with an alignment which are not power of two. However, the percpu allocator never supported alignments which are not power of two and has always behaved incorectly in thise case. Commit 3ca45a46 "percpu: ensure requested alignment is power of two" introduced a check which trigger a warning [1] when booting linux-next on Xen. But in reality this bug was always present. This can be fixed by replacing the call to __alloc_percpu with alloc_percpu. The latter will use an alignment which are a power of two. [1] [ 0.023921] illegal size (48) or align (48) for percpu allocation [ 0.024167] ------------[ cut here ]------------ [ 0.024344] WARNING: CPU: 0 PID: 1 at linux/mm/percpu.c:892 pcpu_alloc+0x88/0x6c0 [ 0.024584] Modules linked in: [ 0.024708] [ 0.024804] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-rc7-next-20161128 #473 [ 0.025012] Hardware name: Foundation-v8A (DT) [ 0.025162] task: ffff80003d870000 task.stack: ffff80003d844000 [ 0.025351] PC is at pcpu_alloc+0x88/0x6c0 [ 0.025490] LR is at pcpu_alloc+0x88/0x6c0 [ 0.025624] pc : [<ffff00000818e678>] lr : [<ffff00000818e678>] pstate: 60000045 [ 0.025830] sp : ffff80003d847cd0 [ 0.025946] x29: ffff80003d847cd0 x28: 0000000000000000 [ 0.026147] x27: 0000000000000000 x26: 0000000000000000 [ 0.026348] x25: 0000000000000000 x24: 0000000000000000 [ 0.026549] x23: 0000000000000000 x22: 00000000024000c0 [ 0.026752] x21: ffff000008e97000 x20: 0000000000000000 [ 0.026953] x19: 0000000000000030 x18: 0000000000000010 [ 0.027155] x17: 0000000000000a3f x16: 00000000deadbeef [ 0.027357] x15: 0000000000000006 x14: ffff000088f79c3f [ 0.027573] x13: ffff000008f79c4d x12: 0000000000000041 [ 0.027782] x11: 0000000000000006 x10: 0000000000000042 [ 0.027995] x9 : ffff80003d847a40 x8 : 6f697461636f6c6c [ 0.028208] x7 : 6120757063726570 x6 : ffff000008f79c84 [ 0.028419] x5 : 0000000000000005 x4 : 0000000000000000 [ 0.028628] x3 : 0000000000000000 x2 : 000000000000017f [ 0.028840] x1 : ffff80003d870000 x0 : 0000000000000035 [ 0.029056] [ 0.029152] ---[ end trace 0000000000000000 ]--- [ 0.029297] Call trace: [ 0.029403] Exception stack(0xffff80003d847b00 to 0xffff80003d847c30) [ 0.029621] 7b00: 0000000000000030 0001000000000000 ffff80003d847cd0 ffff00000818e678 [ 0.029901] 7b20: 0000000000000002 0000000000000004 ffff000008f7c060 0000000000000035 [ 0.030153] 7b40: ffff000008f79000 ffff000008c4cd88 ffff80003d847bf0 ffff000008101778 [ 0.030402] 7b60: 0000000000000030 0000000000000000 ffff000008e97000 00000000024000c0 [ 0.030647] 7b80: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 0.030895] 7ba0: 0000000000000035 ffff80003d870000 000000000000017f 0000000000000000 [ 0.031144] 7bc0: 0000000000000000 0000000000000005 ffff000008f79c84 6120757063726570 [ 0.031394] 7be0: 6f697461636f6c6c ffff80003d847a40 0000000000000042 0000000000000006 [ 0.031643] 7c00: 0000000000000041 ffff000008f79c4d ffff000088f79c3f 0000000000000006 [ 0.031877] 7c20: 00000000deadbeef 0000000000000a3f [ 0.032051] [<ffff00000818e678>] pcpu_alloc+0x88/0x6c0 [ 0.032229] [<ffff00000818ece8>] __alloc_percpu+0x18/0x20 [ 0.032409] [<ffff000008d9606c>] xen_guest_init+0x174/0x2f4 [ 0.032591] [<ffff0000080830f8>] do_one_initcall+0x38/0x130 [ 0.032783] [<ffff000008d90c34>] kernel_init_freeable+0xe0/0x248 [ 0.032995] [<ffff00000899a890>] kernel_init+0x10/0x100 [ 0.033172] [<ffff000008082ec0>] ret_from_fork+0x10/0x50 Reported-by:
Wei Chen <wei.chen@arm.com> Link: https://lkml.org/lkml/2016/11/28/669Signed-off-by:
Julien Grall <julien.grall@arm.com> Signed-off-by:
Stefano Stabellini <sstabellini@kernel.org> Reviewed-by:
-
Alan Stern authored
commit ccdb6be9 upstream. The UHCI controllers in Intel chipsets rely on a platform-specific non-PME mechanism for wakeup signalling. They can generate wakeup signals even though they don't support PME. We need to let the USB core know this so that it will enable runtime suspend for UHCI controllers. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Felipe Balbi authored
commit e8f29bb7 upstream. usb_endpoint_maxp() returns wMaxPacketSize in its raw form. Without taking into consideration that it also contains other bits reserved for isochronous endpoints. This patch fixes one occasion where this is a problem by making sure that we initialize ep->maxpacket only with lower 10 bits of the value returned by usb_endpoint_maxp(). Note that seperate patches will be necessary to audit all call sites of usb_endpoint_maxp() and make sure that usb_endpoint_maxp() only returns lower 10 bits of wMaxPacketSize. Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Guenter Roeck authored
commit 22547c4c upstream. On a system with a defective USB device connected to an USB hub, an endless sequence of port connect events was observed. The sequence of events as observed is as follows: - Port reports connected event (port status=USB_PORT_STAT_CONNECTION). - Event handler debounces port and resets it by calling hub_port_reset(). - hub_port_reset() calls hub_port_wait_reset() to wait for the reset to complete. - The reset completes, but USB_PORT_STAT_CONNECTION is not immediately set in the port status register. - hub_port_wait_reset() returns -ENOTCONN. - Port initialization sequence is aborted. - A few milliseconds later, the port again reports a connected event, and the sequence repeats. This continues either forever or, randomly, stops if the connection is already re-established when the port status is read. It results in a high rate of udev events. This in turn destabilizes userspace since the above sequence holds the device mutex pretty much continuously and prevents userspace from actually reading the device status. To prevent the problem from happening, let's wait for the connection to be re-established after a port reset. If the device was actually disconnected, the code will still return an error, but it will do so only after the long reset timeout. Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Janusz Dziedzic authored
commit de288e36 upstream. In the case of bounced ep0 requests, we must delay DMA operation until after ->complete() otherwise we might overwrite contents of req->buf. This caused problems with RNDIS gadget. Signed-off-by:
Janusz Dziedzic <januszx.dziedzic@intel.com> Signed-off-by:
-
Guenter Roeck authored
commit dcc7620c upstream. Upstream commit 98d74f9c ("xhci: fix 10 second timeout on removal of PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI xhci controllers which can result in excessive timeouts, to the point where the system reports a deadlock. The same problem is seen with hot pluggable xhci controllers using the xhci-plat driver, such as the driver used for Type-C ports on rk3399. Similar to hot-pluggable PCI controllers, the driver for this chip removes the xhci controller from the system when the Type-C cable is disconnected. The solution for PCI devices works just as well for non-PCI devices and avoids the problem. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Felipe Balbi authored
commit 7369090a upstream. Some gadget drivers are bad, bad boys. We notice that ADB was passing bad Burst Size which caused top bits of param0 to be overwritten which confused DWC3 when running this command. In order to avoid future issues, we're going to make sure values passed by macros are always safe for the controller. Note that ADB still needs a fix to *not* pass bad values. Reported-by:
Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by:
Adam Andruszak <adam.andruszak@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 8727bf68 upstream. Fix errors during open not being returned to userspace. Specifically, failed control-line manipulations or control or read urb submissions would not be detected. Fixes: 7fb57a01 ("USB: cdc-acm: Fix potential deadlock (lockdep warning)") Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 703df329 upstream. We must not do the usb_autopm_put_interface() before submitting the read urbs or we might end up doing I/O to a suspended device. Fixes: 088c64f8 ("USB: cdc-acm: re-write read processing") Signed-off-by:
-
Alexey Khoroshilov authored
commit 070c0b17 upstream. If acm_submit_read_urbs() fails in acm_port_activate(), error handling code calls usb_autopm_put_interface() while it is already called before acm_submit_read_urbs(). The patch reorganizes error handling code to avoid double decrement of USB interface's PM-usage counter. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Felipe Balbi authored
commit eaa496ff upstream. ep->mult is supposed to be set to Isochronous and Interrupt Endapoint's multiplier value. This value is computed from different places depending on the link speed. If we're dealing with HighSpeed, then it's part of bits [12:11] of wMaxPacketSize. This case wasn't taken into consideration before. While at that, also make sure the ep->mult defaults to one so drivers can use it unconditionally and assume they'll never multiply ep->maxpacket to zero. Signed-off-by:
-
Johan Hovold authored
commit e35d6d7c upstream. Bind to the interface, but do not register any ports, after having downloaded the firmware. The device will still disconnect and re-enumerate, but this way we avoid an error messages from being logged as part of the process: io_ti: probe of 1-1.3:1.0 failed with error -5 Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Mathias Nyman authored
commit ee8665e2 upstream. the tt_info provided by a HS hub might be in use to by a child device Make sure we free the devices in the correct order. This is needed in special cases such as when xhci controller is reset when resuming from hibernate, and all virt_devices are freed. Also free the virt_devices starting from max slot_id as children more commonly have higher slot_id than parent. Reported-by:
Guenter Roeck <groeck@chromium.org> Tested-by:
-
Alan Stern authored
commit 1c069b05 upstream. Andrey Konovalov's fuzz testing of gadgetfs showed that we should improve the driver's checks for valid configuration descriptors passed in by the user. In particular, the driver needs to verify that the wTotalLength value in the descriptor is not too short (smaller than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is too large has to be changed, because the driver assumes there is always enough room remaining in the buffer to hold a device descriptor (at least USB_DT_DEVICE_SIZE bytes). This patch adds the additional check and fixes the existing check. It may do a little more than strictly necessary, but one extra check won't hurt. Signed-off-by:
-
Alan Stern authored
commit add333a8 upstream. Andrey Konovalov reports that fuzz testing with syzkaller causes a KASAN use-after-free bug report in gadgetfs: BUG: KASAN: use-after-free in gadgetfs_setup+0x208a/0x20e0 at addr ffff88003dfe5bf2 Read of size 2 by task syz-executor0/22994 CPU: 3 PID: 22994 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #16 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff88006df06a18 ffffffff81f96aba ffffffffe0528500 1ffff1000dbe0cd6 ffffed000dbe0cce ffff88006df068f0 0000000041b58ab3 ffffffff8598b4c8 ffffffff81f96828 1ffff1000dbe0ccd ffff88006df06708 ffff88006df06748 Call Trace: <IRQ> [ 201.343209] [< inline >] __dump_stack lib/dump_stack.c:15 <IRQ> [ 201.343209] [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159 [< inline >] print_address_description mm/kasan/report.c:197 [<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286 [< inline >] kasan_report mm/kasan/report.c:306 [<ffffffff817e562a>] __asan_report_load_n_noabort+0x3a/0x40 mm/kasan/report.c:337 [< inline >] config_buf drivers/usb/gadget/legacy/inode.c:1298 [<ffffffff8322c8fa>] gadgetfs_setup+0x208a/0x20e0 drivers/usb/gadget/legacy/inode.c:1368 [<ffffffff830fdcd0>] dummy_timer+0x11f0/0x36d0 drivers/usb/gadget/udc/dummy_hcd.c:1858 [<ffffffff814807c1>] call_timer_fn+0x241/0x800 kernel/time/timer.c:1308 [< inline >] expire_timers kernel/time/timer.c:1348 [<ffffffff81482de6>] __run_timers+0xa06/0xec0 kernel/time/timer.c:1641 [<ffffffff814832c1>] run_timer_softirq+0x21/0x80 kernel/time/timer.c:1654 [<ffffffff84f4af8b>] __do_softirq+0x2fb/0xb63 kernel/softirq.c:284 The cause of the bug is subtle. The dev_config() routine gets called twice by the fuzzer. The first time, the user data contains both a full-speed configuration descriptor and a high-speed config descriptor, causing dev->hs_config to be set. But it also contains an invalid device descriptor, so the buffer containing the descriptors is deallocated and dev_config() returns an error. The second time dev_config() is called, the user data contains only a full-speed config descriptor. But dev->hs_config still has the stale pointer remaining from the first call, causing the routine to think that there is a valid high-speed config. Later on, when the driver dereferences the stale pointer to copy that descriptor, we get a use-after-free access. The fix is simple: Clear dev->hs_config if the passed-in data does not contain a high-speed config descriptor. Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
-
Alan Stern authored
commit faab5098 upstream. Andrey Konovalov reports that fuzz testing with syzkaller causes a KASAN warning in gadgetfs: BUG: KASAN: slab-out-of-bounds in dev_config+0x86f/0x1190 at addr ffff88003c47e160 Write of size 65537 by task syz-executor0/6356 CPU: 3 PID: 6356 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff88003c107ad8 ffffffff81f96aba ffffffff3dc11ef0 1ffff10007820eee ffffed0007820ee6 ffff88003dc11f00 0000000041b58ab3 ffffffff8598b4c8 ffffffff81f96828 ffffffff813fb4a0 ffff88003b6eadc0 ffff88003c107738 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159 [< inline >] print_address_description mm/kasan/report.c:197 [<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286 [<ffffffff817e5705>] kasan_report+0x35/0x40 mm/kasan/report.c:306 [< inline >] check_memory_region_inline mm/kasan/kasan.c:308 [<ffffffff817e3fb9>] check_memory_region+0x139/0x190 mm/kasan/kasan.c:315 [<ffffffff817e4044>] kasan_check_write+0x14/0x20 mm/kasan/kasan.c:326 [< inline >] copy_from_user arch/x86/include/asm/uaccess.h:689 [< inline >] ep0_write drivers/usb/gadget/legacy/inode.c:1135 [<ffffffff83228caf>] dev_config+0x86f/0x1190 drivers/usb/gadget/legacy/inode.c:1759 [<ffffffff817fdd55>] __vfs_write+0x5d5/0x760 fs/read_write.c:510 [<ffffffff817ff650>] vfs_write+0x170/0x4e0 fs/read_write.c:560 [< inline >] SYSC_write fs/read_write.c:607 [<ffffffff81803a5b>] SyS_write+0xfb/0x230 fs/read_write.c:599 [<ffffffff84f47ec1>] entry_SYSCALL_64_fastpath+0x1f/0xc2 Indeed, there is a comment saying that the value of len is restricted to a 16-bit integer, but the code doesn't actually do this. This patch fixes the warning. It replaces the comment with a computation that forces the amount of data copied from the user in ep0_write() to be no larger than the wLength size for the control transfer, which is a 16-bit quantity. Signed-off-by:
-
Greg Kroah-Hartman authored
commit 0994b0a2 upstream. Andrey Konovalov reported that we were not properly checking the upper limit before of a device configuration size before calling memdup_user(), which could cause some problems. So set the upper limit to PAGE_SIZE * 4, which should be good enough for all devices. Reported-by:
-
Con Kolivas authored
commit 82ffb6fc upstream. The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the following warning. [ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072), cval->res is probably wrong. [ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1 Adding it to the list of devices in volume_control_quirks makes it work properly, fixing related typo. Signed-off-by:
Con Kolivas <kernel@kolivas.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 4e7655fd upstream. The snd_use_lock_sync() (thus its implementation snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of the sync loop. It was introduced from the beginning, just to be "safer", in terms of avoiding the stupid bugs. However, as Ben Hutchings suggested, this timeout rather introduces a potential leak or use-after-free that was apparently fixed by the commit 2d7d5400 ("ALSA: seq: Fix race during FIFO resize"): for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() -> copy_from_user() could block for a long time, and snd_use_lock_sync() goes timeout and still leaves the cell at releasing the pool. For fixing such a problem, we remove the break by the timeout while still keeping the warning. Suggested-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Takashi Iwai authored
commit 2d7d5400 upstream. When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
-
Takashi Iwai authored
commit c520ff3d upstream. When snd_seq_pool_done() is called, it marks the closing flag to refuse the further cell insertions. But snd_seq_pool_done() itself doesn't clear the cells but just waits until all cells are cleared by the caller side. That is, it's racy, and this leads to the endless stall as syzkaller spotted. This patch addresses the racy by splitting the setup of pool->closing flag out of snd_seq_pool_done(), and calling it properly before snd_seq_pool_done(). BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.comReported-and-tested-by:
-
Takashi Iwai authored
commit f3ac9f73 upstream. The sequencer FIFO management has a bug that may lead to a corruption (shortage) of the cell linked list. When a sequencer client faces an error at the event delivery, it tries to put back the dequeued cell. When the first queue was put back, this forgot the tail pointer tracking, and the link will be screwed up. Although there is no memory corruption, the sequencer client may stall forever at exit while flushing the pending FIFO cells in snd_seq_pool_done(), as spotted by syzkaller. This patch addresses the missing tail pointer tracking at snd_seq_fifo_cell_putback(). Also the patch makes sure to clear the cell->enxt pointer at snd_seq_fifo_event_in() for avoiding a similar mess-up of the FIFO linked list. Reported-by:
-
Takashi Iwai authored
commit 71321eb3 upstream. When a user sets a too small ticks with a fine-grained timer like hrtimer, the kernel tries to fire up the timer irq too frequently. This may lead to the condensed locks, eventually the kernel spinlock lockup with warnings. For avoiding such a situation, we define a lower limit of the resolution, namely 1ms. When the user passes a too small tick value that results in less than that, the kernel returns -EINVAL now. Reported-by:
-
Takashi Iwai authored
commit 37a7ea4a upstream. snd_seq_pool_done() syncs with closing of all opened threads, but it aborts the wait loop with a timeout, and proceeds to the release resource even if not all threads have been closed. The timeout was 5 seconds, and if you run a crazy stuff, it can exceed easily, and may result in the access of the invalid memory address -- this is what syzkaller detected in a bug report. As a fix, let the code graduate from naiveness, simply remove the loop timeout. BugLink: http://lkml.kernel.org/r/CACT4Y+YdhDV2H5LLzDTJDVF-qiYHUHhtRaW4rbb4gUhTCQB81w@mail.gmail.comReported-by:
-
