- 07 Mar, 2011 13 commits
-
-
Richard Zhu authored
Signed-off-by:
Richard Zhao <richard.zhao@freescale.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Richard Zhu authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Gwenhael Goavec-Merou authored
Signed-off-by:
Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by:
-
Gwenhael Goavec-Merou authored
Signed-off-by:
-
Gwenhael Goavec-Merou authored
Signed-off-by:
-
Gwenhael Goavec-Merou authored
Signed-off-by:
-
Ryan Lortie authored
Change imx31_add_imx_keypad() to imx35_add_imx_keypad() in mach-mx3/devices-imx35.h. Signed-off-by:
Ryan Lortie <desrt@desrt.ca> Acked-by:
-
Ryan Lortie authored
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor Reference Manual" the correct address for the pad control register IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8. Signed-off-by:
Marc Reilly <marc@cpdesign.com.au> Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
Eric Bénard <eric@eukrea.com> Signed-off-by:
-
Lothar Waßmann authored
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and me. Signed-off-by:
Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by:
-
Sascha Hauer authored
It is used for example in the i2c driver which can be compiled modular. Signed-off-by:
-
- 01 Mar, 2011 10 commits
-
-
Sascha Hauer authored
Signed-off-by:
-
Uwe Kleine-König authored
This is not strictly necessary but the right thing to do. Signed-off-by: -
Lothar Waßmann authored
This is not strictly necessary but the right thing to do. Signed-off-by:
-
Uwe Kleine-König authored
This fixes a small memory leak that was only hit in very unlikely error paths Signed-off-by: -
Lothar Waßmann authored
This fixes a small memory leak that was only hit in very unlikely error paths. Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
- wrong MUX was set before for IRQ - get_pendown_state is no more needed Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Wolfram Sang authored
The latter are error-prone because the bank number is one less than one would read in the documentation. Signed-off-by:
-
- 28 Feb, 2011 4 commits
-
-
Denis 'GNUtoo' Carikli authored
Note that the hardware schematics and documentations can be obtained here: http://www.bugcommunity.com/wiki/index.php/BUGbaseSigned-off-by:
Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Acked-by:
-
Shawn Guo authored
This patch is to fix the warning below. arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS Signed-off-by:
Shawn Guo <shawn.guo@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Richard Zhu authored
Signed-off-by:
-
- 21 Feb, 2011 2 commits
-
-
Richard Zhao authored
Signed-off-by:
-
Frank Li authored
Signed-off-by:
Frank Li <Frank.Li@freescale.com> Signed-off-by:
-
- 18 Feb, 2011 11 commits
-
-
Richard Zhao authored
Most fix is for uart txd/cts. They don't need to select input. And fix some other pads with wrong select input. Signed-off-by:
-
Richard Zhao authored
Signed-off-by:
-
Richard Zhao authored
Signed-off-by:
-
Richard Zhao authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Arnaud Patard (Rtp) authored
Signed-off-by:
Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by:
-
Arnaud Patard (Rtp) authored
Enable cpufreq on Genesi efika platforms Signed-off-by:
-
Arnaud Patard (Rtp) authored
This patch declares regulators for the efikamx. Use it also to power off the efikamx. Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to power off by setting GPIO 4 13 to high level instead of powering off through the mc13892. Signed-off-by:
-
Arnaud Patard (Rtp) authored
Now that usb has been fixed, we can enable usb h1 on efikamx Signed-off-by:
-
Arnaud Patard (Rtp) authored
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things so it makes sense to create a common file for both devices and a specific file for each. No functionnal change except dropping uart 1 & 2. Signed-off-by:
-
