- 19 Sep, 2019 40 commits
-
-
Steffen Dirkwinkel authored
commit 9452fbf5 upstream. The CB4063 board uses pmc_plt_clk* clocks for ethernet controllers. This adds it to the critclk_systems DMI table so the clocks are marked as CLK_CRITICAL and not turned off. Fixes: 648e9218 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by:
Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Yang Yingliang authored
commit 93651f80 upstream. If CONFIG_ARCH_HAS_STRICT_MODULE_RWX is not defined, we need stub for module_enable_nx() and module_enable_x(). If CONFIG_ARCH_HAS_STRICT_MODULE_RWX is defined, but CONFIG_STRICT_MODULE_RWX is disabled, we need stub for module_enable_nx. Move frob_text() outside of the CONFIG_STRICT_MODULE_RWX, because it is needed anyway. Fixes: 2eef1399 ("modules: fix BUG when load module with rodata=n") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
Jessica Yu <jeyu@kernel.org> Signed-off-by:
-
Yang Yingliang authored
commit 2eef1399 upstream. When loading a module with rodata=n, it causes an executing NX-protected page BUG. [ 32.379191] kernel tried to execute NX-protected page - exploit attempt? (uid: 0) [ 32.382917] BUG: unable to handle page fault for address: ffffffffc0005000 [ 32.385947] #PF: supervisor instruction fetch in kernel mode [ 32.387662] #PF: error_code(0x0011) - permissions violation [ 32.389352] PGD 240c067 P4D 240c067 PUD 240e067 PMD 421a52067 PTE 8000000421a53063 [ 32.391396] Oops: 0011 [#1] SMP PTI [ 32.392478] CPU: 7 PID: 2697 Comm: insmod Tainted: G O 5.2.0-rc5+ #202 [ 32.394588] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 32.398157] RIP: 0010:ko_test_init+0x0/0x1000 [ko_test] [ 32.399662] Code: Bad RIP value. [ 32.400621] RSP: 0018:ffffc900029f3ca8 EFLAGS: 00010246 [ 32.402171] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 32.404332] RDX: 00000000000004c7 RSI: 0000000000000cc0 RDI: ffffffffc0005000 [ 32.406347] RBP: ffffffffc0005000 R08: ffff88842fbebc40 R09: ffffffff810ede4a [ 32.408392] R10: ffffea00108e3480 R11: 0000000000000000 R12: ffff88842bee21a0 [ 32.410472] R13: 0000000000000001 R14: 0000000000000001 R15: ffffc900029f3e78 [ 32.412609] FS: 00007fb4f0c0a700(0000) GS:ffff88842fbc0000(0000) knlGS:0000000000000000 [ 32.414722] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 32.416290] CR2: ffffffffc0004fd6 CR3: 0000000421a90004 CR4: 0000000000020ee0 [ 32.418471] Call Trace: [ 32.419136] do_one_initcall+0x41/0x1df [ 32.420199] ? _cond_resched+0x10/0x40 [ 32.421433] ? kmem_cache_alloc_trace+0x36/0x160 [ 32.422827] do_init_module+0x56/0x1f7 [ 32.423946] load_module+0x1e67/0x2580 [ 32.424947] ? __alloc_pages_nodemask+0x150/0x2c0 [ 32.426413] ? map_vm_area+0x2d/0x40 [ 32.427530] ? __vmalloc_node_range+0x1ef/0x260 [ 32.428850] ? __do_sys_init_module+0x135/0x170 [ 32.430060] ? _cond_resched+0x10/0x40 [ 32.431249] __do_sys_init_module+0x135/0x170 [ 32.432547] do_syscall_64+0x43/0x120 [ 32.433853] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Because if rodata=n, set_memory_x() can't be called, fix this by calling set_memory_x in complete_formation(); Fixes: f2c65fb3 ("x86/modules: Avoid breaking W^X while loading modules") Suggested-by:
Jian Cheng <cj.chengjian@huawei.com> Reviewed-by:
Nadav Amit <namit@vmware.com> Signed-off-by:
-
Olivier Moysan authored
commit c6013bf5 upstream. Fix the data type as DFSDM raw output is complements 2, 24bits left aligned in a 32-bit register. This change does not affect AUDIO path - Set data as signed for IIO (as for AUDIO) - Set 8 bit right shift for IIO. The 8 LSBs bits of data contains channel info and are masked. Signed-off-by:
Olivier Moysan <olivier.moysan@st.com> Fixes: e2e6771c ("IIO: ADC: add STM32 DFSDM sigma delta ADC support") Acked-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Mario Limonciello authored
commit 1ffdb51f upstream. This reverts commit a0085f25. This commit has caused regressions in notebooks that support suspend to idle such as the XPS 9360, XPS 9370 and XPS 9380. These notebooks will wakeup from suspend to idle from an unsolicited advertising packet from an unpaired BLE device. In a bug report it was sugggested that this is caused by a generic lack of LE privacy support. Revert this commit until that behavior can be avoided by the kernel. Fixes: a0085f25 ("Bluetooth: btusb: driver to enable the usb-wakeup feature") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=200039 Link: https://marc.info/?l=linux-bluetooth&m=156441081612627&w=2 Link: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/750073/ CC: Bastien Nocera <hadess@hadess.net> CC: Christian Kellner <ckellner@redhat.com> CC: Sukumar Ghorai <sukumar.ghorai@intel.com> Signed-off-by:
Mario Limonciello <mario.limonciello@dell.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Nishka Dasgupta authored
commit 165d42c0 upstream. Each iteration of for_each_child_of_node puts the previous node, but in the case of a goto from the middle of the loop, there is no put, thus causing a memory leak. Hence add an of_node_put before the goto in two places. Issue found with Coccinelle. Fixes: 119f5173 (drm/mediatek: Add DRM Driver for Mediatek SoC MT8173) Signed-off-by:
Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by:
CK Hu <ck.hu@mediatek.com> Signed-off-by:
-
Hans de Goede authored
commit dae1ccee upstream. Newer GPD MicroPC BIOS versions have proper DMI strings, add an extra quirk table entry for these new strings. This is good news, as this means that we no longer have to update the BIOS dates list with every BIOS update. Fixes: 652b8b08("drm: panel-orientation-quirks: Add quirk for GPD MicroPC") Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190624154014.8557-2-hdegoede@redhat.comSigned-off-by:
-
Andrew F. Davis authored
commit 66f030ea upstream. TI-SCI firmware will only respond to messages when the TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages already do this, set this for the ones that do not. This will be enforced in future firmware that better match the TI-SCI specifications, this patch will not break users of existing firmware. Fixes: aa276781 ("firmware: Add basic support for TI System Control Interface (TI-SCI) protocol") Signed-off-by:
Andrew F. Davis <afd@ti.com> Acked-by:
Nishanth Menon <nm@ti.com> Tested-by:
Alejandro Hernandez <ajhernandez@ti.com> Signed-off-by:
Tero Kristo <t-kristo@ti.com> Signed-off-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Christophe Leroy authored
commit 4bbfb839 upstream. In that mode, hardware ICV verification is not supported. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Fixes: 7405c8d7 ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Christophe Leroy authored
commit 7ede4c36 upstream. For decrypt, req->cryptlen includes the size of the authentication part while all functions of the driver expect cryptlen to be the size of the encrypted data. As it is not expected to change req->cryptlen, this patch implements local calculation of cryptlen. Signed-off-by:
-
Christophe Leroy authored
commit d84cc9c9 upstream. ECB's ivsize must be 0. Signed-off-by:
-
Christophe Leroy authored
commit ee483d32 upstream. When data size is not a multiple of the alg's block size, the SEC generates an error interrupt and dumps the registers. And for NULL size, the SEC does just nothing and the interrupt is awaited forever. This patch ensures the data size is correct before submitting the request to the SEC engine. Signed-off-by:
-
Christophe Leroy authored
commit b9a05b60 upstream. CTR has a blocksize of 1. Signed-off-by:
-
Christophe Leroy authored
commit 1ba34e71 upstream. Although the HW accepts any size and silently truncates it to the correct length, the extra tests expects EINVAL to be returned when the key size is not valid. Signed-off-by:
-
Muchun Song authored
commit ac43432c upstream. There is a race condition between removing glue directory and adding a new device under the glue dir. It can be reproduced in following test: CPU1: CPU2: device_add() get_device_parent() class_dir_create_and_add() kobject_add_internal() create_dir() // create glue_dir device_add() get_device_parent() kobject_get() // get glue_dir device_del() cleanup_glue_dir() kobject_del(glue_dir) kobject_add() kobject_add_internal() create_dir() // in glue_dir sysfs_create_dir_ns() kernfs_create_dir_ns(sd) sysfs_remove_dir() // glue_dir->sd=NULL sysfs_put() // free glue_dir->sd // sd is freed kernfs_new_node(sd) kernfs_get(glue_dir) kernfs_add_one() kernfs_put() Before CPU1 remove last child device under glue dir, if CPU2 add a new device under glue dir, the glue_dir kobject reference count will be increase to 2 via kobject_get() in get_device_parent(). And CPU2 has been called kernfs_create_dir_ns(), but not call kernfs_new_node(). Meanwhile, CPU1 call sysfs_remove_dir() and sysfs_put(). This result in glue_dir->sd is freed and it's reference count will be 0. Then CPU2 call kernfs_get(glue_dir) will trigger a warning in kernfs_get() and increase it's reference count to 1. Because glue_dir->sd is freed by CPU1, the next call kernfs_add_one() by CPU2 will fail(This is also use-after-free) and call kernfs_put() to decrease reference count. Because the reference count is decremented to 0, it will also call kmem_cache_free() to free the glue_dir->sd again. This will result in double free. In order to avoid this happening, we also should make sure that kernfs_node for glue_dir is released in CPU1 only when refcount for glue_dir kobj is 1 to fix this race. The following calltrace is captured in kernel 4.14 with the following patch applied: commit 726e4109 ("drivers: core: Remove glue dirs from sysfs earlier") -------------------------------------------------------------------------- [ 3.633703] WARNING: CPU: 4 PID: 513 at .../fs/kernfs/dir.c:494 Here is WARN_ON(!atomic_read(&kn->count) in kernfs_get(). .... [ 3.633986] Call trace: [ 3.633991] kernfs_create_dir_ns+0xa8/0xb0 [ 3.633994] sysfs_create_dir_ns+0x54/0xe8 [ 3.634001] kobject_add_internal+0x22c/0x3f0 [ 3.634005] kobject_add+0xe4/0x118 [ 3.634011] device_add+0x200/0x870 [ 3.634017] _request_firmware+0x958/0xc38 [ 3.634020] request_firmware_into_buf+0x4c/0x70 .... [ 3.634064] kernel BUG at .../mm/slub.c:294! Here is BUG_ON(object == fp) in set_freepointer(). .... [ 3.634346] Call trace: [ 3.634351] kmem_cache_free+0x504/0x6b8 [ 3.634355] kernfs_put+0x14c/0x1d8 [ 3.634359] kernfs_create_dir_ns+0x88/0xb0 [ 3.634362] sysfs_create_dir_ns+0x54/0xe8 [ 3.634366] kobject_add_internal+0x22c/0x3f0 [ 3.634370] kobject_add+0xe4/0x118 [ 3.634374] device_add+0x200/0x870 [ 3.634378] _request_firmware+0x958/0xc38 [ 3.634381] request_firmware_into_buf+0x4c/0x70 -------------------------------------------------------------------------- Fixes: 726e4109 ("drivers: core: Remove glue dirs from sysfs earlier") Signed-off-by:
Muchun Song <smuchun@gmail.com> Reviewed-by:
Mukesh Ojha <mojha@codeaurora.org> Signed-off-by:
Prateek Sood <prsood@codeaurora.org> Link: https://lore.kernel.org/r/20190727032122.24639-1-smuchun@gmail.comSigned-off-by:
-
Richard Weinberger authored
commit bacfa94b upstream. Commit c877154d fixed an uninitialized variable and optimized the function to not call tnc_next() in the first iteration of the loop. While this seemed perfectly legit and wise, it turned out to be illegal. If the lookup function does not find an exact match it will rewind the cursor by 1. The rewinded cursor will not match the name hash we are looking for and this results in a spurious -ENOENT. So we need to move to the next entry in case of an non-exact match, but not if the match was exact. While we are here, update the documentation to avoid further confusion. Cc: Hyunchul Lee <hyc.lee@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Fixes: c877154d ("ubifs: Fix uninitialized variable in search_dh_cookie()") Fixes: 781f675e ("ubifs: Fix unlink code wrt. double hash lookups") Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Kent Gibson authored
commit 5ca2f54b upstream. lineevent_create should not allow any of GPIOHANDLE_REQUEST_OUTPUT, GPIOHANDLE_REQUEST_OPEN_DRAIN or GPIOHANDLE_REQUEST_OPEN_SOURCE to be set. Fixes: d7c51b47 ("gpio: userspace ABI for reading/writing GPIO lines") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Kent Gibson <warthog618@gmail.com> Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
-
Alex Williamson authored
commit 2d2f4273 upstream. Commit 0e7df224 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding") introduced the sriov_drivers_autoprobe attribute which allows users to prevent the kernel from automatically probing a driver for new VFs as they are created. This allows VFs to be spawned without automatically binding the new device to a host driver, such as in cases where the user intends to use the device only with a meta driver like vfio-pci. However, the current implementation prevents any use of drivers_probe with the VF while sriov_drivers_autoprobe=0. This blocks the now current general practice of setting driver_override followed by using drivers_probe to bind a device to a specified driver. The kernel never automatically sets a driver_override therefore it seems we can assume a driver_override reflects the intent of the user. Also, probing a device using a driver_override match seems outside the scope of the 'auto' part of sriov_drivers_autoprobe. Therefore, let's allow driver_override matches regardless of sriov_drivers_autoprobe, which we can do by simply testing if a driver_override is set for a device as a 'can probe' condition. Fixes: 0e7df224 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding") Link: https://lore.kernel.org/lkml/155742996741.21878.569845487290798703.stgit@gimli.home Link: https://lore.kernel.org/linux-pci/155672991496.20698.4279330795743262888.stgit@gimli.home/T/#uSigned-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Xiaolei Li authored
commit 336d4b13 upstream. One main goal of the function mtk_nfc_update_ecc_stats is to check whether sectors are all empty. If they are empty, set these sectors's data buffer and OOB buffer as 0xff. But now, the sector OOB buffer pointer is wrongly assigned. We always do memset from sector 0. To fix this issue, pass start sector number to make OOB buffer pointer be properly assigned. Fixes: 1d6b1e46 ("mtd: mediatek: driver for MTK Smart Device") Signed-off-by:
Xiaolei Li <xiaolei.li@mediatek.com> Reviewed-by:
Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by:
-
Douglas Anderson authored
commit 6943b839 upstream. At boot time, my rk3288-veyron devices yell with 8 lines that look like this: [ 0.000000] rockchip_mmc_get_phase: invalid clk rate This is because the clock framework at clk_register() time tries to get the phase but we don't have a parent yet. While the errors appear to be harmless they are still ugly and, in general, we don't want yells like this in the log unless they are important. There's no real reason to be yelling here. We can still return -EINVAL to indicate that the phase makes no sense without a parent. If someone really tries to do tuning and the clock is reported as 0 then we'll see the yells in rockchip_mmc_set_phase(). Fixes: 4bf59902 ("clk: rockchip: Prevent calculating mmc phase if clock rate is zero") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Neil Armstrong authored
commit 5ffff441 upstream. Add missing XBGR8888 & ABGR8888 formats variants from the primary plane. Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
Kevin Hilman <khilman@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190429075238.7884-1-narmstrong@baylibre.comSigned-off-by:
-
Suraj Jitindar Singh authored
commit 6fbcdd59 upstream. Commit ddf35cf3 ("powerpc: Use barrier_nospec in copy_from_user()") Added barrier_nospec before loading from user-controlled pointers. The intention was to order the load from the potentially user-controlled pointer vs a previous branch based on an access_ok() check or similar. In order to achieve the same result, add a barrier_nospec to the raw_copy_in_user() function before loading from such a user-controlled pointer. Fixes: ddf35cf3 ("powerpc: Use barrier_nospec in copy_from_user()") Signed-off-by:
Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Steve Wahl authored
x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors commit e16c2983 upstream. The last change to this Makefile caused relocation errors when loading a kdump kernel. Restore -mcmodel=large (not -mcmodel=kernel), -ffreestanding, and -fno-zero-initialized-bsss, without reverting to the former practice of resetting KBUILD_CFLAGS. Purgatory.ro is a standalone binary that is not linked against the rest of the kernel. Its image is copied into an array that is linked to the kernel, and from there kexec relocates it wherever it desires. With the previous change to compiler flags, the error "kexec: Overflow in relocation type 11 value 0x11fffd000" was encountered when trying to load the crash kernel. This is from kexec code trying to relocate the purgatory.ro object. From the error message, relocation type 11 is R_X86_64_32S. The x86_64 ABI says: "The R_X86_64_32 and R_X86_64_32S relocations truncate the computed value to 32-bits. The linker must verify that the generated value for the R_X86_64_32 (R_X86_64_32S) relocation zero-extends (sign-extends) to the original 64-bit value." This type of relocation doesn't work when kexec chooses to place the purgatory binary in memory that is not reachable with 32 bit addresses. The compiler flag -mcmodel=kernel allows those type of relocations to be emitted, so revert to using -mcmodel=large as was done before. Also restore the -ffreestanding and -fno-zero-initialized-bss flags because they are appropriate for a stand alone piece of object code which doesn't explicitly zero the bss, and one other report has said undefined symbols are encountered without -ffreestanding. These identical compiler flag changes need to happen for every object that becomes part of the purgatory.ro object, so gather them together first into PURGATORY_CFLAGS_REMOVE and PURGATORY_CFLAGS, and then apply them to each of the objects that have C source. Do not apply any of these flags to kexec-purgatory.o, which is not part of the standalone object but part of the kernel proper. Tested-by:
Vaibhav Rustagi <vaibhavrustagi@google.com> Tested-by:
Andreas Smas <andreas@lonelycoder.com> Signed-off-by:
Steve Wahl <steve.wahl@hpe.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: None Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: clang-built-linux@googlegroups.com Cc: dimitri.sivanich@hpe.com Cc: mike.travis@hpe.com Cc: russ.anderson@hpe.com Fixes: b059f801 ("x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS") Link: https://lkml.kernel.org/r/20190905202346.GA26595@swahl-linuxSigned-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Andreas Smas <andreas@lonelycoder.com> Signed-off-by:
-
Paolo Bonzini authored
commit f7eea636 upstream. The implementation of vmread to memory is still incomplete, as it lacks the ability to do vmread to I/O memory just like vmptrst. Cc: stable@vger.kernel.org Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Fuqian Huang authored
commit 541ab2ae upstream. Emulation of VMPTRST can incorrectly inject a page fault when passed an operand that points to an MMIO address. The page fault will use uninitialized kernel stack memory as the CR2 and error code. The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR exit to userspace; however, it is not an easy fix, so for now just ensure that the error code and CR2 are zero. Signed-off-by:
Fuqian Huang <huangfq.daxian@gmail.com> Cc: stable@vger.kernel.org [add comment] Signed-off-by:
-
Thomas Huth authored
commit 53936b5b upstream. When the userspace program runs the KVM_S390_INTERRUPT ioctl to inject an interrupt, we convert them from the legacy struct kvm_s390_interrupt to the new struct kvm_s390_irq via the s390int_to_s390irq() function. However, this function does not take care of all types of interrupts that we can inject into the guest later (see do_inject_vcpu()). Since we do not clear out the s390irq values before calling s390int_to_s390irq(), there is a chance that we copy random data from the kernel stack which could be leaked to the userspace later. Specifically, the problem exists with the KVM_S390_INT_PFAULT_INIT interrupt: s390int_to_s390irq() does not handle it, and the function __inject_pfault_init() later copies irq->u.ext which contains the random kernel stack data. This data can then be leaked either to the guest memory in __deliver_pfault_init(), or the userspace might retrieve it directly with the KVM_S390_GET_IRQ_STATE ioctl. Fix it by handling that interrupt type in s390int_to_s390irq(), too, and by making sure that the s390irq struct is properly pre-initialized. And while we're at it, make sure that s390int_to_s390irq() now directly returns -EINVAL for unknown interrupt types, so that we immediately get a proper error code in case we add more interrupt types to do_inject_vcpu() without updating s390int_to_s390irq() sometime in the future. Cc: stable@vger.kernel.org Reviewed-by:
David Hildenbrand <david@redhat.com> Reviewed-by:
Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by:
Janosch Frank <frankja@linux.ibm.com> Signed-off-by:
Thomas Huth <thuth@redhat.com> Link: https://lore.kernel.org/kvm/20190912115438.25761-1-thuth@redhat.comSigned-off-by:
-
Igor Mammedov authored
commit 13a17cc0 upstream. If userspace doesn't set KVM_MEM_LOG_DIRTY_PAGES on memslot before calling kvm_s390_vm_start_migration(), kernel will oops with: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 0000000000000000 TEID: 0000000000000483 Fault in home space mode while using kernel ASCE. AS:0000000002a2000b R2:00000001bff8c00b R3:00000001bff88007 S:00000001bff91000 P:000000000000003d Oops: 0004 ilc:2 [#1] SMP ... Call Trace: ([<001fffff804ec552>] kvm_s390_vm_set_attr+0x347a/0x3828 [kvm]) [<001fffff804ecfc0>] kvm_arch_vm_ioctl+0x6c0/0x1998 [kvm] [<001fffff804b67e4>] kvm_vm_ioctl+0x51c/0x11a8 [kvm] [<00000000008ba572>] do_vfs_ioctl+0x1d2/0xe58 [<00000000008bb284>] ksys_ioctl+0x8c/0xb8 [<00000000008bb2e2>] sys_ioctl+0x32/0x40 [<000000000175552c>] system_call+0x2b8/0x2d8 INFO: lockdep is turned off. Last Breaking-Event-Address: [<0000000000dbaf60>] __memset+0xc/0xa0 due to ms->dirty_bitmap being NULL, which might crash the host. Make sure that ms->dirty_bitmap is set before using it or return -EINVAL otherwise. Cc: <stable@vger.kernel.org> Fixes: afdad616 ("KVM: s390: Fix storage attributes migration with memory slots") Signed-off-by:
Igor Mammedov <imammedo@redhat.com> Link: https://lore.kernel.org/kvm/20190911075218.29153-1-imammedo@redhat.com/Reviewed-by:
Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by:
Cornelia Huck <cohuck@redhat.com> Reviewed-by:
-
Yunfeng Ye authored
commit eddf3e9c upstream. The following crash was observed: Unable to handle kernel NULL pointer dereference at 0000000000000158 Internal error: Oops: 96000004 [#1] SMP pc : resend_irqs+0x68/0xb0 lr : resend_irqs+0x64/0xb0 ... Call trace: resend_irqs+0x68/0xb0 tasklet_action_common.isra.6+0x84/0x138 tasklet_action+0x2c/0x38 __do_softirq+0x120/0x324 run_ksoftirqd+0x44/0x60 smpboot_thread_fn+0x1ac/0x1e8 kthread+0x134/0x138 ret_from_fork+0x10/0x18 The reason for this is that the interrupt resend mechanism happens in soft interrupt context, which is a asynchronous mechanism versus other operations on interrupts. free_irq() does not take resend handling into account. Thus, the irq descriptor might be already freed before the resend tasklet is executed. resend_irqs() does not check the return value of the interrupt descriptor lookup and derefences the return value unconditionally. 1): __setup_irq irq_startup check_irq_resend // activate softirq to handle resend irq 2): irq_domain_free_irqs irq_free_descs free_desc call_rcu(&desc->rcu, delayed_free_desc) 3): __do_softirq tasklet_action resend_irqs desc = irq_to_desc(irq) desc->handle_irq(desc) // desc is NULL --> Ooops Fix this by adding a NULL pointer check in resend_irqs() before derefencing the irq descriptor. Fixes: a4633adc ("[PATCH] genirq: add genirq sw IRQ-retrigger") Signed-off-by:
Yunfeng Ye <yeyunfeng@huawei.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Zhiqiang Liu <liuzhiqiang26@huawei.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1630ae13-5c8e-901e-de09-e740b6a426a7@huawei.comSigned-off-by:
-
Alexander Duyck authored
commit 377228ac upstream. There were a couple cases where the ITR value generated via the adaptive ITR scheme could exceed 126. This resulted in the value becoming either 0 or something less than 10. Switching back and forth between a value less than 10 and a value greater than 10 can cause issues as certain hardware features such as RSC to not function well when the ITR value has dropped that low. CC: stable@vger.kernel.org Fixes: b4ded832 ("ixgbe: Update adaptive ITR algorithm") Reported-by:
Gregg Leventhal <gleventhal@janestreet.com> Signed-off-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Filipe Manana authored
commit 410f954c upstream. Sometimes when fsync'ing a file we need to log that other inodes exist and when we need to do that we acquire a reference on the inodes and then drop that reference using iput() after logging them. That generally is not a problem except if we end up doing the final iput() (dropping the last reference) on the inode and that inode has a link count of 0, which can happen in a very short time window if the logging path gets a reference on the inode while it's being unlinked. In that case we end up getting the eviction callback, btrfs_evict_inode(), invoked through the iput() call chain which needs to drop all of the inode's items from its subvolume btree, and in order to do that, it needs to join a transaction at the helper function evict_refill_and_join(). However because the task previously started a transaction at the fsync handler, btrfs_sync_file(), it has current->journal_info already pointing to a transaction handle and therefore evict_refill_and_join() will get that transaction handle from btrfs_join_transaction(). From this point on, two different problems can happen: 1) evict_refill_and_join() will often change the transaction handle's block reserve (->block_rsv) and set its ->bytes_reserved field to a value greater than 0. If evict_refill_and_join() never commits the transaction, the eviction handler ends up decreasing the reference count (->use_count) of the transaction handle through the call to btrfs_end_transaction(), and after that point we have a transaction handle with a NULL ->block_rsv (which is the value prior to the transaction join from evict_refill_and_join()) and a ->bytes_reserved value greater than 0. If after the eviction/iput completes the inode logging path hits an error or it decides that it must fallback to a transaction commit, the btrfs fsync handle, btrfs_sync_file(), gets a non-zero value from btrfs_log_dentry_safe(), and because of that non-zero value it tries to commit the transaction using a handle with a NULL ->block_rsv and a non-zero ->bytes_reserved value. This makes the transaction commit hit an assertion failure at btrfs_trans_release_metadata() because ->bytes_reserved is not zero but the ->block_rsv is NULL. The produced stack trace for that is like the following: [192922.917158] assertion failed: !trans->bytes_reserved, file: fs/btrfs/transaction.c, line: 816 [192922.917553] ------------[ cut here ]------------ [192922.917922] kernel BUG at fs/btrfs/ctree.h:3532! [192922.918310] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI [192922.918666] CPU: 2 PID: 883 Comm: fsstress Tainted: G W 5.1.4-btrfs-next-47 #1 [192922.919035] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014 [192922.919801] RIP: 0010:assfail.constprop.25+0x18/0x1a [btrfs] (...) [192922.920925] RSP: 0018:ffffaebdc8a27da8 EFLAGS: 00010286 [192922.921315] RAX: 0000000000000051 RBX: ffff95c9c16a41c0 RCX: 0000000000000000 [192922.921692] RDX: 0000000000000000 RSI: ffff95cab6b16838 RDI: ffff95cab6b16838 [192922.922066] RBP: ffff95c9c16a41c0 R08: 0000000000000000 R09: 0000000000000000 [192922.922442] R10: ffffaebdc8a27e70 R11: 0000000000000000 R12: ffff95ca731a0980 [192922.922820] R13: 0000000000000000 R14: ffff95ca84c73338 R15: ffff95ca731a0ea8 [192922.923200] FS: 00007f337eda4e80(0000) GS:ffff95cab6b00000(0000) knlGS:0000000000000000 [192922.923579] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [192922.923948] CR2: 00007f337edad000 CR3: 00000001e00f6002 CR4: 00000000003606e0 [192922.924329] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [192922.924711] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [192922.925105] Call Trace: [192922.925505] btrfs_trans_release_metadata+0x10c/0x170 [btrfs] [192922.925911] btrfs_commit_transaction+0x3e/0xaf0 [btrfs] [192922.926324] btrfs_sync_file+0x44c/0x490 [btrfs] [192922.926731] do_fsync+0x38/0x60 [192922.927138] __x64_sys_fdatasync+0x13/0x20 [192922.927543] do_syscall_64+0x60/0x1c0 [192922.927939] entry_SYSCALL_64_after_hwframe+0x49/0xbe (...) [192922.934077] ---[ end trace f00808b12068168f ]--- 2) If evict_refill_and_join() decides to commit the transaction, it will be able to do it, since the nested transaction join only increments the transaction handle's ->use_count reference counter and it does not prevent the transaction from getting committed. This means that after eviction completes, the fsync logging path will be using a transaction handle that refers to an already committed transaction. What happens when using such a stale transaction can be unpredictable, we are at least having a use-after-free on the transaction handle itself, since the transaction commit will call kmem_cache_free() against the handle regardless of its ->use_count value, or we can end up silently losing all the updates to the log tree after that iput() in the logging path, or using a transaction handle that in the meanwhile was allocated to another task for a new transaction, etc, pretty much unpredictable what can happen. In order to fix both of them, instead of using iput() during logging, use btrfs_add_delayed_iput(), so that the logging path of fsync never drops the last reference on an inode, that step is offloaded to a safe context (usually the cleaner kthread). The assertion failure issue was sporadically triggered by the test case generic/475 from fstests, which loads the dm error target while fsstress is running, which lead to fsync failing while logging inodes with -EIO errors and then trying later to commit the transaction, triggering the assertion failure. CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Kent Gibson authored
commit e95fbc13 upstream. linehandle_create should not allow both GPIOHANDLE_REQUEST_INPUT and GPIOHANDLE_REQUEST_OUTPUT to be set. Fixes: d7c51b47 ("gpio: userspace ABI for reading/writing GPIO lines") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Hans de Goede authored
commit 61f7f7c8 upstream. Another day; another DSDT bug we need to workaround... Since commit ca876c74 ("gpiolib-acpi: make sure we trigger edge events at least once on boot") we call _AEI edge handlers at boot. In some rare cases this causes problems. One example of this is the Minix Neo Z83-4 mini PC, this device has a clear DSDT bug where it has some copy and pasted code for dealing with Micro USB-B connector host/device role switching, while the mini PC does not even have a micro-USB connector. This code, which should not be there, messes with the DDC data pin from the HDMI connector (switching it to GPIO mode) breaking HDMI support. To avoid problems like this, this commit adds a new gpiolib_acpi.run_edge_events_on_boot kernel commandline option, which allows disabling the running of _AEI edge event handlers at boot. The default value is -1/auto which uses a DMI based blacklist, the initial version of this blacklist contains the Neo Z83-4 fixing the HDMI breakage. Cc: stable@vger.kernel.org Cc: Daniel Drake <drake@endlessm.com> Cc: Ian W MORRISON <ianwmorrison@gmail.com> Reported-by:
Ian W MORRISON <ianwmorrison@gmail.com> Suggested-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Yang Yingliang authored
[ Upstream commit 77f22f92 ] I got a UAF repport in tun driver when doing fuzzy test: [ 466.269490] ================================================================== [ 466.271792] BUG: KASAN: use-after-free in tun_chr_read_iter+0x2ca/0x2d0 [ 466.271806] Read of size 8 at addr ffff888372139250 by task tun-test/2699 [ 466.271810] [ 466.271824] CPU: 1 PID: 2699 Comm: tun-test Not tainted 5.3.0-rc1-00001-g5a9433db2614-dirty #427 [ 466.271833] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 466.271838] Call Trace: [ 466.271858] dump_stack+0xca/0x13e [ 466.271871] ? tun_chr_read_iter+0x2ca/0x2d0 [ 466.271890] print_address_description+0x79/0x440 [ 466.271906] ? vprintk_func+0x5e/0xf0 [ 466.271920] ? tun_chr_read_iter+0x2ca/0x2d0 [ 466.271935] __kasan_report+0x15c/0x1df [ 466.271958] ? tun_chr_read_iter+0x2ca/0x2d0 [ 466.271976] kasan_report+0xe/0x20 [ 466.271987] tun_chr_read_iter+0x2ca/0x2d0 [ 466.272013] do_iter_readv_writev+0x4b7/0x740 [ 466.272032] ? default_llseek+0x2d0/0x2d0 [ 466.272072] do_iter_read+0x1c5/0x5e0 [ 466.272110] vfs_readv+0x108/0x180 [ 466.299007] ? compat_rw_copy_check_uvector+0x440/0x440 [ 466.299020] ? fsnotify+0x888/0xd50 [ 466.299040] ? __fsnotify_parent+0xd0/0x350 [ 466.299064] ? fsnotify_first_mark+0x1e0/0x1e0 [ 466.304548] ? vfs_write+0x264/0x510 [ 466.304569] ? ksys_write+0x101/0x210 [ 466.304591] ? do_preadv+0x116/0x1a0 [ 466.304609] do_preadv+0x116/0x1a0 [ 466.309829] do_syscall_64+0xc8/0x600 [ 466.309849] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 466.309861] RIP: 0033:0x4560f9 [ 466.309875] Code: 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 [ 466.309889] RSP: 002b:00007ffffa5166e8 EFLAGS: 00000206 ORIG_RAX: 0000000000000127 [ 466.322992] RAX: ffffffffffffffda RBX: 0000000000400460 RCX: 00000000004560f9 [ 466.322999] RDX: 0000000000000003 RSI: 00000000200008c0 RDI: 0000000000000003 [ 466.323007] RBP: 00007ffffa516700 R08: 0000000000000004 R09: 0000000000000000 [ 466.323014] R10: 0000000000000000 R11: 0000000000000206 R12: 000000000040cb10 [ 466.323021] R13: 0000000000000000 R14: 00000000006d7018 R15: 0000000000000000 [ 466.323057] [ 466.323064] Allocated by task 2605: [ 466.335165] save_stack+0x19/0x80 [ 466.336240] __kasan_kmalloc.constprop.8+0xa0/0xd0 [ 466.337755] kmem_cache_alloc+0xe8/0x320 [ 466.339050] getname_flags+0xca/0x560 [ 466.340229] user_path_at_empty+0x2c/0x50 [ 466.341508] vfs_statx+0xe6/0x190 [ 466.342619] __do_sys_newstat+0x81/0x100 [ 466.343908] do_syscall_64+0xc8/0x600 [ 466.345303] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 466.347034] [ 466.347517] Freed by task 2605: [ 466.348471] save_stack+0x19/0x80 [ 466.349476] __kasan_slab_free+0x12e/0x180 [ 466.350726] kmem_cache_free+0xc8/0x430 [ 466.351874] putname+0xe2/0x120 [ 466.352921] filename_lookup+0x257/0x3e0 [ 466.354319] vfs_statx+0xe6/0x190 [ 466.355498] __do_sys_newstat+0x81/0x100 [ 466.356889] do_syscall_64+0xc8/0x600 [ 466.358037] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 466.359567] [ 466.360050] The buggy address belongs to the object at ffff888372139100 [ 466.360050] which belongs to the cache names_cache of size 4096 [ 466.363735] The buggy address is located 336 bytes inside of [ 466.363735] 4096-byte region [ffff888372139100, ffff88837213a100) [ 466.367179] The buggy address belongs to the page: [ 466.368604] page:ffffea000dc84e00 refcount:1 mapcount:0 mapping:ffff8883df1b4f00 index:0x0 compound_mapcount: 0 [ 466.371582] flags: 0x2fffff80010200(slab|head) [ 466.372910] raw: 002fffff80010200 dead000000000100 dead000000000122 ffff8883df1b4f00 [ 466.375209] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000 [ 466.377778] page dumped because: kasan: bad access detected [ 466.379730] [ 466.380288] Memory state around the buggy address: [ 466.381844] ffff888372139100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 466.384009] ffff888372139180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 466.386131] >ffff888372139200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 466.388257] ^ [ 466.390234] ffff888372139280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 466.392512] ffff888372139300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 466.394667] ================================================================== tun_chr_read_iter() accessed the memory which freed by free_netdev() called by tun_set_iff(): CPUA CPUB tun_set_iff() alloc_netdev_mqs() tun_attach() tun_chr_read_iter() tun_get() tun_do_read() tun_ring_recv() register_netdevice() <-- inject error goto err_detach tun_detach_all() <-- set RCV_SHUTDOWN free_netdev() <-- called from err_free_dev path netdev_freemem() <-- free the memory without check refcount (In this path, the refcount cannot prevent freeing the memory of dev, and the memory will be used by dev_put() called by tun_chr_read_iter() on CPUB.) (Break from tun_ring_recv(), because RCV_SHUTDOWN is set) tun_put() dev_put() <-- use the memory freed by netdev_freemem() Put the publishing of tfile->tun after register_netdevice(), so tun_get() won't get the tun pointer that freed by err_detach path if register_netdevice() failed. Fixes: eb0fb363 ("tuntap: attach queue 0 before registering netdevice") Reported-by:
Hulk Robot <hulkci@huawei.com> Suggested-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Xin Long authored
[ Upstream commit 42dec1db ] Unlike kfree(p), kfree_rcu(p, rcu) won't do NULL pointer check. When tipc_nametbl_remove_publ returns NULL, the panic below happens: BUG: unable to handle kernel NULL pointer dereference at 0000000000000068 RIP: 0010:__call_rcu+0x1d/0x290 Call Trace: <IRQ> tipc_publ_notify+0xa9/0x170 [tipc] tipc_node_write_unlock+0x8d/0x100 [tipc] tipc_node_link_down+0xae/0x1d0 [tipc] tipc_node_check_dest+0x3ea/0x8f0 [tipc] ? tipc_disc_rcv+0x2c7/0x430 [tipc] tipc_disc_rcv+0x2c7/0x430 [tipc] ? tipc_rcv+0x6bb/0xf20 [tipc] tipc_rcv+0x6bb/0xf20 [tipc] ? ip_route_input_slow+0x9cf/0xb10 tipc_udp_recv+0x195/0x1e0 [tipc] ? tipc_udp_is_known_peer+0x80/0x80 [tipc] udp_queue_rcv_skb+0x180/0x460 udp_unicast_rcv_skb.isra.56+0x75/0x90 __udp4_lib_rcv+0x4ce/0xb90 ip_local_deliver_finish+0x11c/0x210 ip_local_deliver+0x6b/0xe0 ? ip_rcv_finish+0xa9/0x410 ip_rcv+0x273/0x362 Fixes: 97ede29e ("tipc: convert name table read-write lock to RCU") Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit af38d07e ] Fix tcp_ecn_withdraw_cwr() to clear the correct bit: TCP_ECN_QUEUE_CWR. Rationale: basically, TCP_ECN_DEMAND_CWR is a bit that is purely about the behavior of data receivers, and deciding whether to reflect incoming IP ECN CE marks as outgoing TCP th->ece marks. The TCP_ECN_QUEUE_CWR bit is purely about the behavior of data senders, and deciding whether to send CWR. The tcp_ecn_withdraw_cwr() function is only called from tcp_undo_cwnd_reduction() by data senders during an undo, so it should zero the sender-side state, TCP_ECN_QUEUE_CWR. It does not make sense to stop the reflection of incoming CE bits on incoming data packets just because outgoing packets were spuriously retransmitted. The bug has been reproduced with packetdrill to manifest in a scenario with RFC3168 ECN, with an incoming data packet with CE bit set and carrying a TCP timestamp value that causes cwnd undo. Before this fix, the IP CE bit was ignored and not reflected in the TCP ECE header bit, and sender sent a TCP CWR ('W') bit on the next outgoing data packet, even though the cwnd reduction had been undone. After this fix, the sender properly reflects the CE bit and does not set the W bit. Note: the bug actually predates 2005 git history; this Fixes footer is chosen to be the oldest SHA1 I have tested (from Sep 2007) for which the patch applies cleanly (since before this commit the code was in a .h file). Fixes: bdf1ee5d ("[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it") Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 10eb56c5 ] Transport should use its own pf_retrans to do the error_count check, instead of asoc's. Otherwise, it's meaningless to make pf_retrans per transport. Fixes: 5aa93bcf ("sctp: Implement quick failover draft from tsvwg") Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit b456d724 ] The '.exit' functions from 'pernet_operations' structure should be marked as __net_exit, not __net_init. Fixes: 8e2d61e0 ("sctp: fix race on protocol/netns initialization") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
-
Cong Wang authored
[ Upstream commit d4d6ec6d ] In case of TCA_HHF_NON_HH_WEIGHT or TCA_HHF_QUANTUM is zero, it would make no progress inside the loop in hhf_dequeue() thus kernel would get stuck. Fix this by checking this corner case in hhf_change(). Fixes: 10239edf ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc") Reported-by: syzbot+bc6297c11f19ee807dc2@syzkaller.appspotmail.com Reported-by: syzbot+041483004a7f45f1f20a@syzkaller.appspotmail.com Reported-by: syzbot+55be5f513bed37fc4367@syzkaller.appspotmail.com Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Terry Lam <vtlam@google.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit b88dd52c ] Whenever MQ is not used on a multiqueue device, we experience serious reordering problems. Bisection found the cited commit. The issue can be described this way : - A single qdisc hierarchy is shared by all transmit queues. (eg : tc qdisc replace dev eth0 root fq_codel) - When/if try_bulk_dequeue_skb_slow() dequeues a packet targetting a different transmit queue than the one used to build a packet train, we stop building the current list and save the 'bad' skb (P1) in a special queue. (bad_txq) - When dequeue_skb() calls qdisc_dequeue_skb_bad_txq() and finds this skb (P1), it checks if the associated transmit queues is still in frozen state. If the queue is still blocked (by BQL or NIC tx ring full), we leave the skb in bad_txq and return NULL. - dequeue_skb() calls q->dequeue() to get another packet (P2) The other packet can target the problematic queue (that we found in frozen state for the bad_txq packet), but another cpu just ran TX completion and made room in the txq that is now ready to accept new packets. - Packet P2 is sent while P1 is still held in bad_txq, P1 might be sent at next round. In practice P2 is the lead of a big packet train (P2,P3,P4 ...) filling the BQL budget and delaying P1 by many packets :/ To solve this problem, we have to block the dequeue process as long as the first packet in bad_txq can not be sent. Reordering issues disappear and no side effects have been seen. Fixes: a53851e2 ("net: sched: explicit locking in gso_cpu fallback") Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
Stefan Chulski authored
[ Upstream commit 63b2ed4e ] Regarding to IEEE 802.3-2015 standard section 2 28B.3 Priority resolution - Table 28-3 - Pause resolution In case of Local device Pause=1 AsymDir=0, Link partner Pause=1 AsymDir=1, Local device resolution should be enable PAUSE transmit, disable PAUSE receive. And in case of Local device Pause=1 AsymDir=1, Link partner Pause=1 AsymDir=0, Local device resolution should be enable PAUSE receive, disable PAUSE transmit. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by:
Stefan Chulski <stefanc@marvell.com> Reported-by:
Shaul Ben-Mayor <shaulb@marvell.com> Acked-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
