- 12 Mar, 2017 40 commits
-
-
Christian Lamparter authored
commit c9f1e326 upstream. This patch fixes the OTP register definitions for the AR934x and AR9550 WMAC SoC. Previously, the ath9k driver was unable to initialize the integrated WMAC on an Aerohive AP121: | ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004 | ath: phy0: timeout (1000 us) on reg 0x30018: 0xbadc0ffe & 0x00000007 != 0x00000004 | ath: phy0: Unable to initialize hardware; initialization status: -5 | ath9k ar934x_wmac: failed to initialize device | ath9k: probe of ar934x_wmac failed with error -5 It turns out that the AR9300_OTP_STATUS and AR9300_OTP_DATA definitions contain a typo. Cc: Gabor Juhos <juhosg@openwrt.org> Fixes: add295a4 "ath9k: use correct OTP register offsets for AR9550" Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
Chris Blake <chrisrblake93@gmail.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Felix Fietkau authored
commit 3a5e969b upstream. The code currently relies on refcounting to disable IRQs from within the IRQ handler and re-enabling them again after the tasklet has run. However, due to race conditions sometimes the IRQ handler might be called twice, or the tasklet may not run at all (if interrupted in the middle of a reset). This can cause nasty imbalances in the irq-disable refcount which will get the driver permanently stuck until the entire radio has been stopped and started again (ath_reset will not recover from this). Instead of using this fragile logic, change the code to ensure that running the irq handler during tasklet processing is safe, and leave the refcount untouched. Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Felix Fietkau authored
commit a70e1d6f upstream. Simply return -EOPNOTSUPP instead. Signed-off-by:
-
Tamizh chelvam authored
commit cb428152 upstream. Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG) configuration are causing the following errors when UTF firmware is loaded to the target. Error message 1: [ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110 [ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110 [ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110 Error message 2: [ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95 [ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95 Avoiding these configurations while bringing the target in testmode is solving the problem. Signed-off-by:
Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by:
-
Alexander Usyskin authored
commit cb97fbbc upstream. Parallel reads from multiple threads on a file descriptor are not well defined and racy. It is safer to return to original behavior and simply fail the additional read. The solution is to remove request for next read credit. Fixes: ff1586a7 ("mei: enqueue consecutive reads") Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Mathias Svensson authored
commit 916cafdc upstream. There were some bugs in the JNE64 and JLT64 comparision macros. This fixes them, improves comments, and cleans up the file while we are at it. Reported-by:
Stephen Röttger <sroettger@google.com> Signed-off-by:
Mathias Svensson <idolf@google.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Theodore Ts'o authored
commit 4753d8a2 upstream. If the file system requires journal recovery, and the device is read-ony, return EROFS to the mount system call. This allows xfstests generic/050 to pass. Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Theodore Ts'o authored
commit 97abd7d4 upstream. If the journal is aborted, the needs_recovery feature flag should not be removed. Otherwise, it's the journal might not get replayed and this could lead to more data getting lost. Signed-off-by:
-
Theodore Ts'o authored
commit eb5efbcb upstream. The write_end() function must always unlock the page and drop its ref count, even on an error. Signed-off-by:
-
Eric Biggers authored
commit dd01b690 upstream. In the case where the child's encryption context was inconsistent with its parent directory, we were using inode->i_sb and inode->i_ino after the inode had already been iput(). Fix this by doing the iput() in the correct places. Note: only ext4 had this bug, not f2fs and ubifs. Fixes: d9cdc903 ("ext4 crypto: enforce context consistency") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Jan Kara authored
commit 3b136499 upstream. ext4_journalled_write_end() did not propely handle all the cases when generic_perform_write() did not copy all the data into the target page and could mark buffers with uninitialized contents as uptodate and dirty leading to possible data corruption (which would be quickly fixed by generic_perform_write() retrying the write but still). Fix the problem by carefully handling the case when the page that is written to is not uptodate. Reported-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit cd648b8a upstream. If filesystem groups are artifically small (using parameter -g to mkfs.ext4), ext4_mb_normalize_request() can result in a request that is larger than a block group. Trim the request size to not confuse allocation code. Reported-by:
"Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Roman Pen authored
commit 03e916fa upstream. Inside ext4_ext_shift_extents() function ext4_find_extent() is called without EXT4_EX_NOCACHE flag, which should prevent cache population. This leads to oudated offsets in the extents tree and wrong blocks afterwards. Patch fixes the problem providing EXT4_EX_NOCACHE flag for each ext4_find_extents() call inside ext4_ext_shift_extents function. Fixes: 331573feSigned-off-by:
Roman Pen <roman.penyaev@profitbricks.com> Signed-off-by:
-
Roman Pen authored
commit 2a9b8cba upstream. While doing 'insert range' start block should be also shifted right. The bug can be easily reproduced by the following test: ptr = malloc(4096); assert(ptr); fd = open("./ext4.file", O_CREAT | O_TRUNC | O_RDWR, 0600); assert(fd >= 0); rc = fallocate(fd, 0, 0, 8192); assert(rc == 0); for (i = 0; i < 2048; i++) *((unsigned short *)ptr + i) = 0xbeef; rc = pwrite(fd, ptr, 4096, 0); assert(rc == 4096); rc = pwrite(fd, ptr, 4096, 4096); assert(rc == 4096); for (block = 2; block < 1000; block++) { rc = fallocate(fd, FALLOC_FL_INSERT_RANGE, 4096, 4096); assert(rc == 0); for (i = 0; i < 2048; i++) *((unsigned short *)ptr + i) = block; rc = pwrite(fd, ptr, 4096, 4096); assert(rc == 4096); } Because start block is not included in the range the hole appears at the wrong offset (just after the desired offset) and the following pwrite() overwrites already existent block, keeping hole untouched. Simple way to verify wrong behaviour is to check zeroed blocks after the test: $ hexdump ./ext4.file | grep '0000 0000' The root cause of the bug is a wrong range (start, stop], where start should be inclusive, i.e. [start, stop]. This patch fixes the problem by including start into the range. But not to break left shift (range collapse) stop points to the beginning of the a block, not to the end. The other not obvious change is an iterator check on validness in a main loop. Because iterator is unsigned the following corner case should be considered with care: insert a block at 0 offset, when stop variables overflows and never becomes less than start, which is 0. To handle this special case iterator is set to NULL to indicate that end of the loop is reached. Fixes: 331573feSigned-off-by:
-
Omar Sandoval authored
commit e02898b4 upstream. loop_reread_partitions() needs to do I/O, but we just froze the queue, so we end up waiting forever. This can easily be reproduced with losetup -P. Fix it by moving the reread to after we unfreeze the queue. Fixes: ecdd0959 ("block/loop: fix race between I/O and set_status") Reported-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
Ming Lei <tom.leiming@gmail.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ming Lei authored
commit ecdd0959 upstream. Inside set_status, transfer need to setup again, so we have to drain IO before the transition, otherwise oops may be triggered like the following: divide error: 0000 [#1] SMP KASAN CPU: 0 PID: 2935 Comm: loop7 Not tainted 4.10.0-rc7+ #213 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 task: ffff88006ba1e840 task.stack: ffff880067338000 RIP: 0010:transfer_xor+0x1d1/0x440 drivers/block/loop.c:110 RSP: 0018:ffff88006733f108 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8800688d7000 RCX: 0000000000000059 RDX: 0000000000000000 RSI: 1ffff1000d743f43 RDI: ffff880068891c08 RBP: ffff88006733f160 R08: ffff8800688d7001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800688d7000 R13: ffff880067b7d000 R14: dffffc0000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88006d000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000006c17e0 CR3: 0000000066e3b000 CR4: 00000000001406f0 Call Trace: lo_do_transfer drivers/block/loop.c:251 [inline] lo_read_transfer drivers/block/loop.c:392 [inline] do_req_filebacked drivers/block/loop.c:541 [inline] loop_handle_cmd drivers/block/loop.c:1677 [inline] loop_queue_work+0xda0/0x49b0 drivers/block/loop.c:1689 kthread_worker_fn+0x4c3/0xa30 kernel/kthread.c:630 kthread+0x326/0x3f0 kernel/kthread.c:227 ret_from_fork+0x31/0x40 arch/x86/entry/entry_64.S:430 Code: 03 83 e2 07 41 29 df 42 0f b6 04 30 4d 8d 44 24 01 38 d0 7f 08 84 c0 0f 85 62 02 00 00 44 89 f8 41 0f b6 48 ff 25 ff 01 00 00 99 <f7> 7d c8 48 63 d2 48 03 55 d0 48 89 d0 48 89 d7 48 c1 e8 03 83 RIP: transfer_xor+0x1d1/0x440 drivers/block/loop.c:110 RSP: ffff88006733f108 ---[ end trace 0166f7bd3b0c0933 ]--- Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Theodore Ts'o authored
commit e112666b upstream. If the journal has been aborted, we shouldn't mark the underlying buffer head as dirty, since that will cause the metadata block to get modified. And if the journal has been aborted, we shouldn't allow this since it will almost certainly lead to a corrupted file system. Signed-off-by:
-
Mathieu Desnoyers authored
commit 90756533 upstream. Userspace applications should be allowed to expect the membarrier system call with MEMBARRIER_CMD_SHARED command to issue memory barriers on nohz_full CPUs, but synchronize_sched() does not take those into account. Given that we do not want unrelated processes to be able to affect real-time sensitive nohz_full CPUs, simply return ENOSYS when membarrier is invoked on a kernel with enabled nohz_full CPUs. Signed-off-by:
Mathieu Desnoyers <mathieu.desnoyers@efficios.com> CC: Josh Triplett <josh@joshtriplett.org> CC: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Rik van Riel <riel@redhat.com> Acked-by:
Lai Jiangshan <jiangshanlai@gmail.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Signed-off-by:
-
Alexandre Belloni authored
commit 0b040874 upstream. LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the proper power off sequence is used before shutting down the platform. Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
-
Hannes Reinecke authored
commit 857de6e0 upstream. The device handler needs to check if a given queue belongs to a scsi device; only then does it make sense to attach a device handler. [mkp: dropped flags] Signed-off-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit c421530b upstream. The driver currently checks the SELF_TEST_FAILED first and then KERNEL_PANIC next. Under error conditions(boot code failure) both SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time. The driver has the capability to reset the controller on an KERNEL_PANIC, but not on SELF_TEST_FAILED. Fixed by first checking KERNEL_PANIC and then the others. Fixes: e8b12f0f ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family) Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
David Carroll <David.Carroll@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Long Li authored
commit 40630f46 upstream. On I/O errors, the Windows driver doesn't set data_transfer_length on error conditions other than SRB_STATUS_DATA_OVERRUN. In these cases we need to set data_transfer_length to 0, indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN, data_transfer_length is set by the Windows driver to the actual data transferred. Reported-by:
Shiva Krishna <Shiva.Krishna@nimblestorage.com> Signed-off-by:
Long Li <longli@microsoft.com> Reviewed-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Long Li authored
commit bba5dc33 upstream. When sense message is present on error, we should pass along to the upper layer to decide how to deal with the error. This patch fixes connectivity issues with Fiber Channel devices. Signed-off-by:
-
Long Li authored
commit 3cd6d3d9 upstream. Properly set SRB flags when hosting device supports tagged queuing. This patch improves the performance on Fiber Channel disks. Signed-off-by:
-
Heinz Mauelshagen authored
commit d36a1954 upstream. The lvm2 sequence to manage dm-raid constructor flags that trigger a rebuild or a reshape is defined as: 1) load table with flags (e.g. rebuild/delta_disks/data_offset) 2) clear out the flags in lvm2 metadata 3) store the lvm2 metadata, reload the table to reset the flags previously established during the initial load (1) -- in order to prevent repeatedly requesting a rebuild or a reshape on activation Currently, loading an inactive table with rebuild/reshape flags specified will cause dm-raid to rebuild/reshape on resume and thus start updating the raid metadata (about the progress). When the second table reload, to reset the flags, occurs the constructor accesses the volatile progress state kept in the raid superblocks. Because the active mapping is still processing the rebuild/reshape, that position will be stale by the time the device is resumed. In the reshape case, this causes data corruption by processing already reshaped stripes again. In the rebuild case, it does _not_ cause data corruption but instead involves superfluous rebuilds. Fix by keeping the raid set frozen during the first resume and then allow the rebuild/reshape during the second resume. Fixes: 9dbd1aa3 ("dm raid: add reshaping support to the target") Signed-off-by:
Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 37a098e9 upstream. The sloppy nature of lockless access to percpu pointers (s->current_path) in rr_select_path(), from multiple threads, is causing some paths to used more than others -- which results in less IO performance being observed. Revert these upstream commits to restore truly symmetric round-robin IO submission in DM multipath: b0b477c7 dm round robin: use percpu 'repeat_count' and 'current_path' 802934b2 dm round robin: do not use this_cpu_ptr() without having preemption disabled There is no benefit to all this complexity if repeat_count = 1 (which is the recommended default). Signed-off-by:
-
Mikulas Patocka authored
commit 60858318 upstream. Fixes: dfcfac3e ("dm stats: collect and report histogram of IO latencies") Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit ca763d0a upstream. A rounding bug due to compiler generated temporary being 32bit was found in remap_to_cache(). A localized cast in remap_to_cache() fixes the corruption but this preferred fix (changing from uint32_t to sector_t) eliminates potential for future rounding errors elsewhere. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Chanwoo Choi authored
commit 30582c25 upstream. Until now, the trans_stat information of passive devfreq is not updated. This patch updates the trans_stat information after setting the target frequency of passive devfreq device. Fixes: 99613311 ("PM / devfreq: Add new passive governor") Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by:
-
Chanwoo Choi authored
commit bcf23c79 upstream. The devfreq using passive governor is not able to change the governor. So, the user can not change the governor through 'available_governor' sysfs entry. Also, the devfreq which don't use the passive governor is not able to change to 'passive' governor on the fly. Fixes: 99613311 ("PM / devfreq: Add new passive governor") Signed-off-by:
-
Mimi Zohar authored
commit bc15ed66 upstream. On failure to return a pathname from ima_d_path(), a pointer to dname is returned, which is subsequently used in the IMA measurement list, the IMA audit records, and other audit logging. Saving the pointer to dname for later use has the potential to race with rename. Intead of returning a pointer to dname on failure, this patch returns a pointer to a copy of the filename. Reported-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Davidlohr Bueso authored
commit 95e91b83 upstream. The issue is described here, with a nice testcase: https://bugzilla.kernel.org/show_bug.cgi?id=192931 The problem is that shmat() calls do_mmap_pgoff() with MAP_FIXED, and the address rounded down to 0. For the regular mmap case, the protection mentioned above is that the kernel gets to generate the address -- arch_get_unmapped_area() will always check for MAP_FIXED and return that address. So by the time we do security_mmap_addr(0) things get funky for shmat(). The testcase itself shows that while a regular user crashes, root will not have a problem attaching a nil-page. There are two possible fixes to this. The first, and which this patch does, is to simply allow root to crash as well -- this is also regular mmap behavior, ie when hacking up the testcase and adding mmap(... |MAP_FIXED). While this approach is the safer option, the second alternative is to ignore SHM_RND if the rounded address is 0, thus only having MAP_SHARED flags. This makes the behavior of shmat() identical to the mmap() case. The downside of this is obviously user visible, but does make sense in that it maintains semantics after the round-down wrt 0 address and mmap. Passes shm related ltp tests. Link: http://lkml.kernel.org/r/1486050195-18629-1-git-send-email-dave@stgolabs.netSigned-off-by:
Davidlohr Bueso <dbueso@suse.de> Reported-by:
Gareth Evans <gareth.evans@contextis.co.uk> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Michael Kerrisk <mtk.manpages@googlemail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Stas Sergeev authored
commit 441398d3 upstream. Currently SS_AUTODISARM is not supported in compatibility mode, but does not return -EINVAL either. This makes dosemu built with -m32 on x86_64 to crash. Also the kernel's sigaltstack selftest fails if compiled with -m32. This patch adds the needed support. Link: http://lkml.kernel.org/r/20170205101213.8163-2-stsp@list.ruSigned-off-by:
Stas Sergeev <stsp@users.sourceforge.net> Cc: Milosz Tanski <milosz@adfin.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Waiman Long <Waiman.Long@hpe.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dmitry Safonov <dsafonov@virtuozzo.com> Cc: Wang Xiaoqiang <wangxq10@lzu.edu.cn> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by:
-
Michal Hocko authored
commit 71ab6cfe upstream. get_scan_count() considers the whole node LRU size when - doing SCAN_FILE due to many page cache inactive pages - calculating the number of pages to scan In both cases this might lead to unexpected behavior especially on 32b systems where we can expect lowmem memory pressure very often. A large highmem zone can easily distort SCAN_FILE heuristic because there might be only few file pages from the eligible zones on the node lru and we would still enforce file lru scanning which can lead to trashing while we could still scan anonymous pages. The later use of lruvec_lru_size can be problematic as well. Especially when there are not many pages from the eligible zones. We would have to skip over many pages to find anything to reclaim but shrink_node_memcg would only reduce the remaining number to scan by SWAP_CLUSTER_MAX at maximum. Therefore we can end up going over a large LRU many times without actually having chance to reclaim much if anything at all. The closer we are out of memory on lowmem zone the worse the problem will be. Fix this by filtering out all the ineligible zones when calculating the lru size for both paths and consider only sc->reclaim_idx zones. The patch would need to be tweaked a bit to apply to 4.10 and older but I will do that as soon as it hits the Linus tree in the next merge window. Link: http://lkml.kernel.org/r/20170117103702.28542-3-mhocko@kernel.org Fixes: b2e18757 ("mm, vmscan: begin reclaiming pages on a per-node basis") Signed-off-by:
Michal Hocko <mhocko@suse.com> Tested-by:
Trevor Cordes <trevor@tecnopolis.ca> Acked-by:
Minchan Kim <minchan@kernel.org> Acked-by:
Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by:
Mel Gorman <mgorman@suse.de> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
Michal Hocko authored
commit fd538803 upstream. lruvec_lru_size returns the full size of the LRU list while we sometimes need a value reduced only to eligible zones (e.g. for lowmem requests). inactive_list_is_low is one such user. Later patches will add more of them. Add a new parameter to lruvec_lru_size and allow it filter out zones which are not eligible for the given context. Link: http://lkml.kernel.org/r/20170117103702.28542-2-mhocko@kernel.orgSigned-off-by:
-
Yisheng Xie authored
commit 9c57b580 upstream. With CONFIG_BALLOON_COMPACTION=y the kernel will mount balloon_mnt for balloon page migration when we probe a virtio_balloon device. However we do not unmount it when removing the device. Fix this. Fixes: b1123ea6 ("mm: balloon: use general non-lru movable page feature") Link: http://lkml.kernel.org/r/1486531318-35189-1-git-send-email-xieyisheng1@huawei.comSigned-off-by:
Yisheng Xie <xieyisheng1@huawei.com> Acked-by:
-
Minchan Kim authored
commit dd8416c4 upstream. With rw_page, page_endio is used for completing IO on a page and it propagates write error to the address space if the IO fails. The problem is it accesses page->mapping directly which might be okay for file-backed pages but it shouldn't for anonymous page. Otherwise, it can corrupt one of field from anon_vma under us and system goes panic randomly. swap_writepage bdev_writepage ops->rw_page I encountered the BUG during developing new zram feature and it was really hard to figure it out because it made random crash, somtime mmap_sem lockdep, sometime other places where places never related to zram/zsmalloc, and not reproducible with some configuration. When I consider how that bug is subtle and people do fast-swap test with brd, it's worth to add stable mark, I think. Fixes: dd6bd0d9 ("swap: use bdev_read_page() / bdev_write_page()") Signed-off-by:
-
Vinayak Menon authored
commit e1587a49 upstream. At the end of a window period, if the reclaimed pages is greater than scanned, an unsigned underflow can result in a huge pressure value and thus a critical event. Reclaimed pages is found to go higher than scanned because of the addition of reclaimed slab pages to reclaimed in shrink_node without a corresponding increment to scanned pages. Minchan Kim mentioned that this can also happen in the case of a THP page where the scanned is 1 and reclaimed could be 512. Link: http://lkml.kernel.org/r/1486641577-11685-1-git-send-email-vinmenon@codeaurora.orgSigned-off-by:
Vinayak Menon <vinmenon@codeaurora.org> Acked-by:
-
Gavin Shan authored
commit e02dc017 upstream. When @node_reclaim_node isn't 0, the page allocator tries to reclaim pages if the amount of free memory in the zones are below the low watermark. On Power platform, none of NUMA nodes are scanned for page reclaim because no nodes match the condition in zone_allows_reclaim(). On Power platform, RECLAIM_DISTANCE is set to 10 which is the distance of Node-A to Node-A. So the preferred node even won't be scanned for page reclaim. __alloc_pages_nodemask() get_page_from_freelist() zone_allows_reclaim() Anton proposed the test code as below: # cat alloc.c : int main(int argc, char *argv[]) { void *p; unsigned long size; unsigned long start, end; start = time(NULL); size = strtoul(argv[1], NULL, 0); printf("To allocate %ldGB memory\n", size); size <<= 30; p = malloc(size); assert(p); memset(p, 0, size); end = time(NULL); printf("Used time: %ld seconds\n", end - start); sleep(3600); return 0; } The system I use for testing has two NUMA nodes. Both have 128GB memory. In below scnario, the page caches on node#0 should be reclaimed when it encounters pressure to accommodate request of allocation. # echo 2 > /proc/sys/vm/zone_reclaim_mode; \ sync; \ echo 3 > /proc/sys/vm/drop_caches; \ # taskset -c 0 cat file.32G > /dev/null; \ grep FilePages /sys/devices/system/node/node0/meminfo Node 0 FilePages: 33619712 kB # taskset -c 0 ./alloc 128 # grep FilePages /sys/devices/system/node/node0/meminfo Node 0 FilePages: 33619840 kB # grep MemFree /sys/devices/system/node/node0/meminfo Node 0 MemFree: 186816 kB With the patch applied, the pagecache on node-0 is reclaimed when its free memory is running out. It's the expected behaviour. # echo 2 > /proc/sys/vm/zone_reclaim_mode; \ sync; \ echo 3 > /proc/sys/vm/drop_caches # taskset -c 0 cat file.32G > /dev/null; \ grep FilePages /sys/devices/system/node/node0/meminfo Node 0 FilePages: 33605568 kB # taskset -c 0 ./alloc 128 # grep FilePages /sys/devices/system/node/node0/meminfo Node 0 FilePages: 1379520 kB # grep MemFree /sys/devices/system/node/node0/meminfo Node 0 MemFree: 317120 kB Fixes: 5f7a75ac ("mm: page_alloc: do not cache reclaim distances") Link: http://lkml.kernel.org/r/1486532455-29613-1-git-send-email-gwshan@linux.vnet.ibm.comSigned-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by:
-
Dan Williams authored
commit b5d24fda upstream. The mem_hotplug_{begin,done} lock coordinates with {get,put}_online_mems() to hold off "readers" of the current state of memory from new hotplug actions. mem_hotplug_begin() expects exclusive access, via the device_hotplug lock, to set mem_hotplug.active_writer. Calling mem_hotplug_begin() without locking device_hotplug can lead to corrupting mem_hotplug.refcount and missed wakeups / soft lockups. [dan.j.williams@intel.com: v2] Link: http://lkml.kernel.org/r/148728203365.38457.17804568297887708345.stgit@dwillia2-desk3.amr.corp.intel.com Link: http://lkml.kernel.org/r/148693885680.16345.17802627926777862337.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: f931ab47 ("mm: fix devm_memremap_pages crash, use mem_hotplug_{begin, done}") Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Reported-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Michal Hocko <mhocko@suse.com> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Signed-off-by:
-
