On some cases, driver returns 1. This should be OK, but qv4l2 is too
strict about return values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Having the device detection happening at reset is bad, as every time,
it will produce a message like:
	tvp5150 2-005c: tvp5150am1 detected.

This only polutes the log and for an accidental kernel hacker, it looks
like a real problem. So, move those printk's to happen during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A few places used T_DIGITAL_TV internally. Remove the usage of this
obsolete mode mask.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

It makes no sense that tuner_lookup would touch at the standby
state. Remove it.

Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Group a few functions together and add/fix comments for each
block of the driver.

This is just a cleanup patch meant to improve driver readability.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This driver is complex, and used by everyone. Better to have it
properly documented.

No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

tuner-core has no business to do with digital TV. So, don't use
T_DIGITAL_TV on it, as it has no code to distinguish between
them, and nobody fills T_DIGITAL_TV right.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Remove the now obsolete set_freq. Also merge set_addr and set_type_addr.

In the past, it used to have two different setup calls, one to set just
the tuner type to any tuner found, and another to set the type only if
the address matches. Those two internal calls were grouped together,
but the functions weren't merged, making the code uglier.

No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A static var is evil, especially if a device has two boards with
xc5000. Instead, just like the other drivers, use stack to store
its config during setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Power down tuners at suspend. At resume, if the tuner is in standby,
calls set_mode, that will turn it on and set the latest frequencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.

Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.

So, instead of keeping the abuse, just use a boolean for storing
such information.

We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.

Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Properly document those functions and do some cleanups around that.
There's just one behavior change on this patchset: it will now restore
TV frequency when changing from radio to TV mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This is a big patch with no functional changes. It just
rearranges everything inside the driver, and prepares to
break TV and Radio into two separate fops groups.

Currently, it has an heuristics logic to determine if the
call came from radio or video. However, the caller driver
knows for sure, so tuner-core shouldn't try to guess it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Move the frequency set debug printk's to the code that actually
are changing it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Nobody is using this legacy call. Just remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L1 was removed. So, the code there is just dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

After registering the cdev, it would be possible do have an open on it.
In a matter of fact, some versions of udev do this. So, move registration
to the end and protect it with a mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

cx88-video has locks. don't use the locked ioctl version, as
it is not needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Adds support for Pixelviex Xcapture USB grabber device.
This device has one composite and one s-video entry
only, plus a button.

For now, the button is not supported.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Some devices don't need to use it. So allow to just disable this logic.
Having it enabled on some devices cause power management to complain,
generating error -71.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Instead of per-model tests all over the code, use some parameters
at the board entries to describe the model variants for:
	- devices with 417 MPEG encoder;
	- devices that use external AV;
	- devices where vbi VANC endpoint doesn't work;
	- devices with xc5000 that require different IF
	  initialization (and probably will cover also
	  xc3028).
	- devices with xceive tuner that require a reset
	  during init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.

Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Just a cleanup patch. Removes one indent level by moving
the return -ENODEV to happen before the device register
logic, if the interface is not the audio/video (int 1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

KERNEL_VERSION: 2.6.37
common.c in function ssize_t si470x_fops_read.

1. First mutex_lock on &radio->lock in line 441
2. Second in line 462

I think that mutex in line 462 is not needed.

 433static ssize_t si470x_fops_read(struct file *file, char __user *buf,
 434                size_t count, loff_t *ppos)
 435{
....
 441        mutex_lock(&radio->lock);
 442        if ((radio->registers[SYSCONFIG1] & SYSCONFIG1_RDS) == 0)
 443                si470x_rds_on(radio);
 444
 445        /* block if no new data available */
 446        while (radio->wr_index == radio->rd_index) {
 447                if (file->f_flags & O_NONBLOCK) {
 448                        retval = -EWOULDBLOCK;
 449                        goto done;
 450                }
 451                if (wait_event_interruptible(radio->read_queue,
 452                        radio->wr_index != radio->rd_index) < 0) {
 453                        retval = -EINTR;
 454                        goto done;
 455                }
 456        }
 457
 458        /* calculate block count from byte count */
 459        count /= 3;
 460
 461        /* copy RDS block out of internal buffer and to user buffer */
 462        mutex_lock(&radio->lock);

Found by Linux Device Drivers Verification Project

Remove second mutex.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Rework registers defines. Add TM6000 specific registers defines.
Add marks and comments for TM6010 specific registers.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Unable to test this due to lack of hardware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Tested with a Logitech QuickCam Pro 4000.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/vivi.c:1059: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>