- 06 Mar, 2015 40 commits
-
-
Trond Myklebust authored
commit ea7c38fe upstream. If we have to do a return-on-close in the delegreturn code, then we must ensure that the inode and super block remain referenced. Cc: Peng Tao <tao.peng@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Reviewed-by:
Peng Tao <tao.peng@primarydata.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit 03a9a42a upstream. Fix an Oopsable condition when nsm_mon_unmon is called as part of the namespace cleanup, which now apparently happens after the utsname has been freed. Link: http://lkml.kernel.org/r/20150125220604.090121ae@neptune.homeReported-by:
Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by:
-
Peng Tao authored
commit cb5d04bc upstream. With pgio refactoring in v3.15, .init_read and .init_write can be called with valid pgio->pg_lseg. file layout was fixed at that time by commit c6194271 (pnfs: filelayout: support non page aligned layouts). But the generic helper still needs to be fixed. Signed-off-by:
-
honclo authored
commit eb71f8a5 upstream. The tpm_ibmvtpm module is affected by an unaligned access problem. ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is enabled in Power partition, which supports both little endian and big endian modes. We added little endian support to fix this problem: 1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS. 2) added be16_to_cpu and be32_to_cpu calls to make sure data received is in LE format on a LE OS. Signed-off-by:
Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by:
Joy Latten <jmlatten@linux.vnet.ibm.com> [phuewe: manually applied the patch :( ] Reviewed-by:
Ashley Lai <ashley@ahsleylai.com> Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
Christophe Ricard authored
commit 1ba3b0b6 upstream. When sending data in tpm_stm_i2c_send, each loop iteration send buf. Send buf + i instead as the goal of this for loop is to send a number of byte from buf that fit in burstcnt. Once those byte are sent, we are supposed to send the next ones. The driver was working because the burstcount value returns always the maximum size for a TPM command or response. (0x800 for a command and 0x400 for a response). Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by:
-
Hon Ching (Vicky) Lo authored
commit 84eb186b upstream. There was an oops in tpm_ibmvtpm_get_desired_dma, which caused kernel panic during boot when vTPM is enabled in Power partition configured in AMS mode. vio_bus_probe calls vio_cmo_bus_probe which calls tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation. The problem is, vio_cmo_bus_probe is called before calling probe, which for vtpm is tpm_ibmvtpm_probe and it's this function that initializes and sets up vtpm's CRQ and gets required data values. Therefore, since this has not yet been done, NULL is returned in attempt to get the size for DMA allocation. We added a NULL check. In addition, a default buffer size will be set when NULL is returned. Signed-off-by:
-
Kiran Padwal authored
commit bb95cd34 upstream. Currently these driver are missing a check on the return value of devm_kzalloc, which would cause a NULL pointer dereference in a OOM situation. This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c Signed-off-by:
Kiran Padwal <kiran.padwal@smartplayin.com> Reviewed-By:
-
David Howells authored
commit 398a1e71 upstream. Add newly registered TPMs to the tail of the list, not the beginning, so that things that are specifying TPM_ANY_NUM don't find that the device they're using has inadvertently changed. Adding a second device would break IMA, for instance. Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
-
Scot Doyle authored
commit 448e9c55 upstream. Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do not send IRQs while also having an ACPI TPM entry indicating that they will be sent. These machines freeze on resume while the tpm_tis module waits for an IRQ, eventually timing out. When in interrupt mode, the tpm_tis module should receive an IRQ during module init. Fall back to polling mode if none is received when expected. Signed-off-by:
Scot Doyle <lkml14@scotdoyle.com> Tested-by:
Michael Mullin <masmullin@gmail.com> Reviewed-by:
-
Florian Fainelli authored
commit 9df11828 upstream. The L2 cache properties were completely off with respect to what the hardware is configured for. Fix the cache-size, cache-line-size and cache-sets to reflect the L2 cache controller we have: 512KB, 16 ways and 32 bytes per cache-line. Fixes: 46d4bca0 ("ARM: BCM63XX: add BCM63138 minimal Device Tree") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Robert Nelson authored
commit 67fd14b3 upstream. Fixes: http://bugs.elinux.org/issues/127 the bb.org community was seeing random reboots before this change. Signed-off-by:
Robert Nelson <robertcnelson@gmail.com> Reviewed-by:
Felipe Balbi <balbi@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Dmitry Osipenko authored
commit de47699d upstream. Commit 58ecb23f ("ARM: tegra: add missing unit addresses to DT") added unit address and changed reg base for GR3D and DSI host1x modules, but these addresses belongs to GR2D and TVO modules respectively. Fix it by changing modules unit and reg base addresses to proper ones. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Fixes: 58ecb23f (ARM: tegra: add missing unit addresses to DT) Reviewed-by:
Alexandre Courbot <acourbot@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Lokesh Vutla authored
commit 1c7e36bf upstream. With commit '7dedd346: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS. On DRA7 UART3 hwmod doesn't have this flag enabled, and atleast on BeagleBoard-X15, where we use UART3 for console, boot fails with DEBUG_LL enabled. Enable DEBUG_OMAP4UART3_FLAGS for UART3 hwmod. For using DEBUG_LL, enable CONFIG_DEBUG_OMAP4UART3 in menuconfig. Fixes: 90020c7b ("ARM: OMAP: DRA7: hwmod: Create initial DRA7XX SoC data") Reviewed-by:
Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit e461894d upstream. StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset by entering the sleep mode. After we have resumed, there is little point in having that bit enabled. Moreover, if this bit is set before reboot, the bootloader can become confused. Thus clear the SMR bit on resume just before clearing the scratchpad (resume address) register. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Tony Battersby authored
commit 564e559f upstream. If the allocation of bt->bs fails, then bt->map can be freed twice, once in blk_mq_init_bitmap_tags() -> bt_alloc(), and once in blk_mq_init_bitmap_tags() -> bt_free(). Fix by setting the pointer to NULL after the first free. Signed-off-by:
Tony Battersby <tonyb@cybernetics.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Vikram Mulukutla authored
commit 7215853e upstream. Commit 6edb2a8a introduced an array map_pages that contains the addresses returned by kmap_atomic. However, when unmapping those pages, map_pages[0] is unmapped before map_pages[1], breaking the nesting requirement as specified in the documentation for kmap_atomic/kunmap_atomic. This was caught by the highmem debug code present in kunmap_atomic. Fix the loop to do the unmapping properly. Link: http://lkml.kernel.org/r/1418871056-6614-1-git-send-email-markivx@codeaurora.orgReviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Reported-by:
Lime Yang <limey@codeaurora.org> Signed-off-by:
Vikram Mulukutla <markivx@codeaurora.org> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Naoya Horiguchi authored
commit cbef8478 upstream. Migrating hugepages and hwpoisoned hugepages are considered as non-present hugepages, and they are referenced via migration entries and hwpoison entries in their page table slots. This behavior causes race condition because pmd_huge() doesn't tell non-huge pages from migrating/hwpoisoned hugepages. follow_page_mask() is one example where the kernel would call follow_page_pte() for such hugepage while this function is supposed to handle only normal pages. To avoid this, this patch makes pmd_huge() return true when pmd_none() is true *and* pmd_present() is false. We don't have to worry about mixing up non-present pmd entry with normal pmd (pointing to leaf level pte entry) because pmd_present() is true in normal pmd. The same race condition could happen in (x86-specific) gup_pmd_range(), where this patch simply adds pmd_present() check instead of pmd_huge(). This is because gup_pmd_range() is fast path. If we have non-present hugepage in this function, we will go into gup_huge_pmd(), then return 0 at flag mask check, and finally fall back to the slow path. Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
James Hogan authored
commit ca5d2564 upstream. Export the _save_msa asm function used by the lose_fpu(1) macro to GPL modules so that KVM can make use of it when it is built as a module. This fixes the following build error when CONFIG_KVM=m and CONFIG_CPU_HAS_MSA=y due to commit f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"): ERROR: "_save_msa" [arch/mips/kvm/kvm.ko] undefined! Fixes: f798217d (KVM: MIPS: Don't leak FPU/DSP to guest) Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9261/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
James Hogan authored
commit 3ce465e0 upstream. Export the _save_fp asm function used by the lose_fpu(1) macro to GPL modules so that KVM can make use of it when it is built as a module. This fixes the following build error when CONFIG_KVM=m due to commit f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"): ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined! Signed-off-by:
-
Markos Chandras authored
commit fde3538a upstream. Whenever we modify a page table entry, we need to ensure that the HTW will not fetch a stable entry. And for that to happen we need to ensure that HTW is stopped before we modify the said entry otherwise the HTW may already be in the process of reading that entry and fetching the old information. As a result of which, we replace the htw_reset() calls with htw_{stop,start} in more appropriate places. This also removes the remaining users of htw_reset() and as a result we drop that macro Signed-off-by:
Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9116/Signed-off-by:
-
Markos Chandras authored
commit 461d1597 upstream. When we use htw_{start,stop}() outside of htw_reset(), we need to ensure that c0 changes have been propagated properly before we attempt to continue with subsequence memory operations. Signed-off-by:
-
Markos Chandras authored
commit 98a833c1 upstream. The "add" instruction is actually a macro in binutils and depending on the size of the immediate it can expand to an "addi" instruction. However, the "addi" instruction traps on overflows which is not something we want on address calculation. Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00121.html Cc: Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by:
-
Markos Chandras authored
commit acac4108 upstream. The "addi" instruction will trap on overflows which is not something we need in this code, so we replace that with "addiu". Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00430.html Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Paul Burton <paul.burton@imgtec.com> Signed-off-by:
-
Manuel Lauss authored
commit 69e4e63e upstream. The current code uses bits 0-6 of the sys_cpupll register to calculate core clock speed. However this is only valid on Au1300, on all earlier models the hardware only uses bits 0-5 to generate core clock. This fixes clock calculation on the MTX1 (Au1500), where bit 6 of cpupll is set as well, which ultimately lead the code to calculate a bogus cpu core clock and also uart base clock down the line. Signed-off-by:
Manuel Lauss <manuel.lauss@gmail.com> Reported-by:
John Crispin <blogic@openwrt.org> Tested-by:
Bruno Randolf <br1@einfach.org> Cc: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/9279/Signed-off-by:
-
James Hogan authored
commit f798217d upstream. The FPU and DSP are enabled via the CP0 Status CU1 and MX bits by kvm_mips_set_c0_status() on a guest exit, presumably in case there is active state that needs saving if pre-emption occurs. However neither of these bits are cleared again when returning to the guest. This effectively gives the guest access to the FPU/DSP hardware after the first guest exit even though it is not aware of its presence, allowing FP instructions in guest user code to intermittently actually execute instead of trapping into the guest OS for emulation. It will then read & manipulate the hardware FP registers which technically belong to the user process (e.g. QEMU), or are stale from another user process. It can also crash the guest OS by causing an FP exception, for which a guest exception handler won't have been registered. First lets save and disable the FPU (and MSA) state with lose_fpu(1) before entering the guest. This simplifies the problem, especially for when guest FPU/MSA support is added in the future, and prevents FR=1 FPU state being live when the FR bit gets cleared for the guest, which according to the architecture causes the contents of the FPU and vector registers to become UNPREDICTABLE. We can then safely remove the enabling of the FPU in kvm_mips_set_c0_status(), since there should never be any active FPU or MSA state to save at pre-emption, which should plug the FPU leak. DSP state is always live rather than being lazily restored, so for that it is simpler to just clear the MX bit again when re-entering the guest. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
James Hogan authored
commit c4c6f2ca upstream. Ensure any hardware page table walker (HTW) is disabled while in KVM guest mode, as KVM doesn't yet set up hardware page table walking for guest mappings so the wrong mappings would get loaded, resulting in the guest hanging or crashing once it reaches userland. The HTW is disabled and re-enabled around the call to __kvm_mips_vcpu_run() which does the initial switch into guest mode and the final switch out of guest context. Additionally it is enabled for the duration of guest exits (i.e. kvm_mips_handle_exit()), getting disabled again before returning back to guest or host. In all cases the HTW is only disabled in normal kernel mode while interrupts are disabled, so that the HTW doesn't get left disabled if the process is preempted. Signed-off-by:
-
Trond Myklebust authored
commit f4086a3d upstream. Commit 411a99ad (nfs: clear_request_commit while holding i_lock) assumes that the nfs_commit_info always points to the inode->i_lock. For historical reasons, that is not the case for O_DIRECT writes. Cc: Weston Andros Adamson <dros@primarydata.com> Fixes: 411a99ad ("nfs: clear_request_commit while holding i_lock") Signed-off-by:
-
Jeff Layton authored
commit 6ffa30d3 upstream. Bruce reported seeing this warning pop when mounting using v4.1: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90 Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014 0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78 0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000 Call Trace: [<ffffffff8186ac78>] dump_stack+0x4c/0x65 [<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0 [<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70 [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90 [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90 [<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0 [<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430 [<ffffffff810d941e>] ? groups_alloc+0x3e/0x130 [<ffffffff810d941e>] groups_alloc+0x3e/0x130 [<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc] [<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc] [<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc] [<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc] [<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4] [<ffffffff810ff970>] ? wait_woken+0xc0/0xc0 [<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4] [<ffffffff810d45bf>] kthread+0x11f/0x140 [<ffffffff810ea815>] ? local_clock+0x15/0x30 [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250 [<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0 [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250 ---[ end trace 675220a11e30f4f2 ]--- nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE, which is just wrong. Fix that by finishing the wait immediately if we've found that the list has something on it. Also, we don't expect this kthread to accept signals, so we should be using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up hung task warnings from the watchdog, so have the schedule_timeout wake up every 60s if there's no callback activity. Reported-by:
"J. Bruce Fields" <bfields@fieldses.org> Signed-off-by:
Jeff Layton <jlayton@primarydata.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 05fbf357 upstream. Lockless access to pte in pagemap_pte_range() might race with page migration and trigger BUG_ON(!PageLocked()) in migration_entry_to_page(): CPU A (pagemap) CPU B (migration) lock_page() try_to_unmap(page, TTU_MIGRATION...) make_migration_entry() set_pte_at() <read *pte> pte_to_pagemap_entry() remove_migration_ptes() unlock_page() if(is_migration_entry()) migration_entry_to_page() BUG_ON(!PageLocked(page)) Also lockless read might be non-atomic if pte is larger than wordsize. Other pte walkers (smaps, numa_maps, clear_refs) already lock ptes. Fixes: 052fb0d6 ("proc: report file/anon bit in /proc/pid/pagemap") Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by:
Andrey Ryabinin <a.ryabinin@samsung.com> Reviewed-by:
Cyrill Gorcunov <gorcunov@openvz.org> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Marcin Wojtas authored
commit a39128bc upstream. According to erratum 'ERR-7878951' Armada 38x SDHCI controller has different capabilities than the ones shown in its registers: - it doesn't support the voltage switching: it can work either with 3.3V or 1.8V supply - it doesn't support the SDR104 mode - SDR50 mode doesn't need tuning The SDHCI_QUIRK_MISSING_CAPS quirk is used for updating the capabilities accordingly. [gregory.clement@free-electrons.com: port from 3.10] Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Gregory CLEMENT authored
commit d4b803c5 upstream. According to erratum 'FE-2946959' both SDR50 and DDR50 modes require specific clock adjustments in SDIO3 Configuration register. However, this register was not part of the device tree binding. Even if the binding can (and will) be extended we still need handling the case where this register was not available. In this case we use the SDHCI_QUIRK_MISSING_CAPS quirk remove them from the capabilities. This commit is based on the work done by Marcin Wojtas<mw@semihalf.com> Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Signed-off-by:
-
Jisheng Zhang authored
commit 14460dba upstream. Current code checks "clk_delay_cycles > 0" to know whether the optional "mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't touch clk_delay_cycles if the property is not set. And type of clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a random value. This patch fix this problem by check the return value of of_property_read_u32() to know whether the optional clk-delay-cycles is set or not. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Jisheng Zhang authored
commit 62cf983a upstream. Commit 0dcaa249 ("sdhci-pxav3: Fix runtime PM initialization") tries to fix one hang issue caused by calling sdhci_add_host() on a suspended device. The fix enables the clock twice, once by clk_prepare_enable() and another by pm_runtime_get_sync(), meaning that the clock will never be gated at runtime PM suspend. I observed the power consumption regression on Marvell BG2Q SoCs. In fact, the fix is not correct. There still be a very small window during which a runtime suspend might somehow occur after pm_runtime_enable() but before pm_runtime_get_sync(). This patch fixes all of the two problems by just incrementing the usage counter before pm_runtime_enable(). It also adjust the order of disabling runtime pm and storing the usage count in the error path to handle clock gating properly. Signed-off-by:
-
Russell King authored
commit fbaa48d1 upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-audio. Fix these. Fixes: 6d746f91 ("[media] em28xx-audio: implement em28xx_ops: suspend/resume hooks") Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Russell King authored
commit a084c57f upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-dvb. Fix these. Fixes: ca2b46da ("[media] em28xx-dvb: implement em28xx_ops: suspend/resume hooks") Signed-off-by:
-
Russell King authored
commit 32e63f03 upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-video. Fix these. Fixes: a61f6811 ("[media] em28xx-video: implement em28xx_ops: suspend/resume hooks") Signed-off-by:
-
Russell King authored
commit 522adc7c upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-core. Fix these. Fixes: 9c669b73 ("[media] em28xx: add suspend/resume to em28xx_ops") Signed-off-by:
-
Russell King authored
commit 7818b0aa upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-audio. Fix these. Fixes: 1b3fd2d3 ("[media] em28xx-audio: don't hardcode audio URB calculus") Signed-off-by:
-
Russell King authored
commit ebfd59cf upstream. Inspection shows that newlines are missing from several kernel messages in em28xx-input. Fix these. Fixes: 5025076a ("[media] em28xx-input: implement em28xx_ops: suspend/resume hooks") Signed-off-by:
-
Russell King authored
commit 0418ca60 upstream. The lockdep splat addressed in a previous commit revealed that at least one message in em28xx-input.c was missing a new line: em28178 #0: Closing input extensionINFO: trying to register non-static key. Further inspection shows several other messages also miss a new line. These will be fixed in a subsequent patch. Fixes: aa929ad7 ("[media] em28xx: print a message at disconnect") Signed-off-by:
-
