In case the HW doesn't perform header-data split, it will write the whole
packet into the data buffer in the WQ, in this case the SHAMPO CQE handler
couldn't use the header entry to build the SKB, instead it should allocate
a new memory to build the SKB using the function:
mlx5e_skb_from_cqe_mpwrq_nonlinear.

Fixes: f97d5c2a ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The HW doesn't wrap the CQE.shampo.header_index field according to the
headers buffer size, instead it always increases it until reaching overflow
of u16 size.

Thus the mlx5e_handle_rx_cqe_mpwrq_shampo handler should mask the
CQE header_index field to find the actual header index in the headers buffer.

Fixes: f97d5c2a ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When changing mode to switchdev, rep bridge init registered to netdevice
notifier holds the devlink lock and then takes pernet_ops_rwsem.
At that time deleting a netns holds pernet_ops_rwsem and then takes
the devlink lock.

Example sequence is:
$ ip netns add foo
$ devlink dev eswitch set pci/0000:00:08.0 mode switchdev &
$ ip netns del foo

deleting netns trace:

[ 1185.365555]  ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.368331]  ? mutex_lock_io_nested+0x13f0/0x13f0
[ 1185.370984]  ? xt_find_table+0x40/0x100
[ 1185.373244]  ? __mutex_lock+0x24a/0x15a0
[ 1185.375494]  ? net_generic+0xa0/0x1c0
[ 1185.376844]  ? wait_for_completion_io+0x280/0x280
[ 1185.377767]  ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.378686]  devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.379579]  ? devlink_nl_cmd_get_dumpit+0x3a0/0x3a0
[ 1185.380557]  ? xt_find_table+0xda/0x100
[ 1185.381367]  cleanup_net+0x372/0x8e0

changing mode to switchdev trace:

[ 1185.411267]  down_write+0x13a/0x150
[ 1185.412029]  ? down_write_killable+0x180/0x180
[ 1185.413005]  register_netdevice_notifier+0x1e/0x210
[ 1185.414000]  mlx5e_rep_bridge_init+0x181/0x360 [mlx5_core]
[ 1185.415243]  mlx5e_uplink_rep_enable+0x269/0x480 [mlx5_core]
[ 1185.416464]  ? mlx5e_uplink_rep_disable+0x210/0x210 [mlx5_core]
[ 1185.417749]  mlx5e_attach_netdev+0x232/0x400 [mlx5_core]
[ 1185.418906]  mlx5e_netdev_attach_profile+0x15b/0x1e0 [mlx5_core]
[ 1185.420172]  mlx5e_netdev_change_profile+0x15a/0x1d0 [mlx5_core]
[ 1185.421459]  mlx5e_vport_rep_load+0x557/0x780 [mlx5_core]
[ 1185.422624]  ? mlx5e_stats_grp_vport_rep_num_stats+0x10/0x10 [mlx5_core]
[ 1185.424006]  mlx5_esw_offloads_rep_load+0xdb/0x190 [mlx5_core]
[ 1185.425277]  esw_offloads_enable+0xd74/0x14a0 [mlx5_core]

Fix this by registering rep bridges for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.

Fixes: 19e9bfa0 ("net/mlx5: Bridge, add offload infrastructure")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Only prio 1 is supported for nic mode when there is no ignore flow level
support in firmware. But for switchdev mode, which supports fixed number
of statically pre-allocated prios, this restriction is not relevant so
it can be relaxed.

Fixes: d671e109 ("net/mlx5: Fix tc max supported prio for nic mode")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.

Fixes: 03a9d11e ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Substitute del_timer() with del_timer_sync() in fw reset polling
deactivation flow, in order to prevent a race condition which occurs
when del_timer() is called and timer is deactivated while another
process is handling the timer interrupt. A situation that led to
the following call trace:
	RIP: 0010:run_timer_softirq+0x137/0x420
	<IRQ>
	recalibrate_cpu_khz+0x10/0x10
	ktime_get+0x3e/0xa0
	? sched_clock_cpu+0xb/0xc0
	__do_softirq+0xf5/0x2ea
	irq_exit_rcu+0xc1/0xf0
	sysvec_apic_timer_interrupt+0x9e/0xc0
	asm_sysvec_apic_timer_interrupt+0x12/0x20
	</IRQ>

Fixes: 38b9f903 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When querying the module EEPROM, there was a misusage of the 'offset'
variable vs the 'query.offset' field.
Fix that by always using 'offset' and assigning its value to
'query.offset' right before the mcia register read call.

While at it, the cross-pages read size adjustment was changed to be more
intuitive.

Fixes: e19b0a34 ("net/mlx5: Refactor module EEPROM query")
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This kind of action is not supported by firmware and generates a
syndrome.

kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)

Fixes: d7e75a32 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Even though net_device->name is guaranteed to be null-terminated string of
size<=IFNAMSIZ, the test robot complains that return value of netdev_name()
can be larger:

In file included from include/trace/define_trace.h:102,
                    from drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h:113,
                    from drivers/net/ethernet/mellanox/mlx5/core/esw/bridge.c:12:
   drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h: In function 'trace_event_raw_event_mlx5_esw_bridge_fdb_template':
>> drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h:24:29: warning: 'strncpy' output may be truncated copying 16 bytes from a string of length 20 [-Wstringop-truncation]
      24 |                             strncpy(__entry->dev_name,
         |                             ^~~~~~~~~~~~~~~~~~~~~~~~~~
      25 |                                     netdev_name(fdb->dev),
         |                                     ~~~~~~~~~~~~~~~~~~~~~~
      26 |                                     IFNAMSIZ);
         |                                     ~~~~~~~~~

This is caused by the fact that default value of IFNAMSIZ is 16, while
placeholder value that is returned by netdev_name() for unnamed net devices
is larger than that.

The offending code is in a tracing function that is only called for mlx5
representors, so there is no straightforward way to reproduce the issue but
let's fix it for correctness sake by replacing strncpy() with strscpy() to
ensure that resulting string is always null-terminated.

Fixes: 9724fd5d ("net/mlx5: Bridge, add tracepoints")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The mlx5_esw_bridge_cleanup() is expected to be called with rtnl lock
taken, which is true for mlx5e_rep_bridge_cleanup() function but not for
error handling code in mlx5e_rep_bridge_init(). Add missing rtnl
lock/unlock calls and extend both mlx5_esw_bridge_cleanup() and its dual
function mlx5_esw_bridge_init() with ASSERT_RTNL() to verify the invariant
from now on.

Fixes: 7cd6a54a ("net/mlx5: Bridge, handle FDB events")
Fixes: 19e9bfa0 ("net/mlx5: Bridge, add offload infrastructure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-01-31

This series contains updates to i40e driver only.

Jedrzej fixes a condition check which would cause an error when
resetting bandwidth when DCB is active with one TC.

Karen resolves a null pointer dereference that could occur when removing
the driver while VSI rings are being disabled.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  i40e: Fix reset path while removing the driver
  i40e: Fix reset bw limit when DCB enabled with 1 TC
====================

Link: https://lore.kernel.org/r/20220201000522.505909-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.

Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.

Fixes: c09440f7 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.

Resolves ipheth 2-1:4.2: ipheth_rcvbulk_callback: urb status: -75

Fixes: f33d9e2b ("usbnet: ipheth: fix connectivity with iOS 14")
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/all/B60B8A4B-92A0-49B3-805D-809A2433B46C@abv.bg/
Link: https://lore.kernel.org/all/24851bd2769434a5fc24730dce8e8a984c5a4505.1643699778.git.jan.kiszka@siemens.com/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We got reports of following warning in inet_sock_destruct()

	WARN_ON(sk_forward_alloc_get(sk));

Whenever we add a non zero-copy fragment to a pure zerocopy skb,
we have to anticipate that whole skb->truesize will be uncharged
when skb is finally freed.

skb->data_len is the payload length. But the memory truesize
estimated by __zerocopy_sg_from_iter() is page aligned.

Fixes: 9b65b17d ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20220201065254.680532-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.

Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.

BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt

write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
 fanout_add net/packet/af_packet.c:1791 [inline]
 packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
 __sys_setsockopt+0x209/0x2a0 net/socket.c:2180
 __do_sys_setsockopt net/socket.c:2191 [inline]
 __se_sys_setsockopt net/socket.c:2188 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
 packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
 __sys_setsockopt+0x209/0x2a0 net/socket.c:2180
 __do_sys_setsockopt net/socket.c:2191 [inline]
 __se_sys_setsockopt net/socket.c:2188 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000000000000000 -> 0xffff888106f8c000

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 47dceb8e ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While looking at one unrelated syzbot bug, I found the replay logic
in __rtnl_newlink() to potentially trigger use-after-free.

It is better to clear master_dev and m_ops inside the loop,
in case we have to replay it.

Fixes: ba7d49b1 ("rtnetlink: provide api for getting and setting slave info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220201012106.216495-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Whenever tc_new_tfilter() jumps back to replay: label,
we need to make sure @q and @chain local variables are cleared again,
or risk use-after-free as in [1]

For consistency, apply the same fix in tc_ctl_chain()

BUG: KASAN: use-after-free in mini_qdisc_pair_swap+0x1b9/0x1f0 net/sched/sch_generic.c:1581
Write of size 8 at addr ffff8880985c4b08 by task syz-executor.4/1945

CPU: 0 PID: 1945 Comm: syz-executor.4 Not tainted 5.17.0-rc1-syzkaller-00495-gff58831f #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 print_address_description.constprop.0.cold+0x8d/0x336 mm/kasan/report.c:255
 __kasan_report mm/kasan/report.c:442 [inline]
 kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
 mini_qdisc_pair_swap+0x1b9/0x1f0 net/sched/sch_generic.c:1581
 tcf_chain_head_change_item net/sched/cls_api.c:372 [inline]
 tcf_chain0_head_change.isra.0+0xb9/0x120 net/sched/cls_api.c:386
 tcf_chain_tp_insert net/sched/cls_api.c:1657 [inline]
 tcf_chain_tp_insert_unique net/sched/cls_api.c:1707 [inline]
 tc_new_tfilter+0x1e67/0x2350 net/sched/cls_api.c:2086
 rtnetlink_rcv_msg+0x80d/0xb80 net/core/rtnetlink.c:5583
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f2647172059
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f2645aa5168 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00007f2647285100 RCX: 00007f2647172059
RDX: 040000000000009f RSI: 00000000200002c0 RDI: 0000000000000006
RBP: 00007f26471cc08d R08: 0000000000000000 R09: 0000000000000000
R10: 9e00000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffb3f7f02f R14: 00007f2645aa5300 R15: 0000000000022000
 </TASK>

Allocated by task 1944:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 kasan_set_track mm/kasan/common.c:45 [inline]
 set_alloc_info mm/kasan/common.c:436 [inline]
 ____kasan_kmalloc mm/kasan/common.c:515 [inline]
 ____kasan_kmalloc mm/kasan/common.c:474 [inline]
 __kasan_kmalloc+0xa9/0xd0 mm/kasan/common.c:524
 kmalloc_node include/linux/slab.h:604 [inline]
 kzalloc_node include/linux/slab.h:726 [inline]
 qdisc_alloc+0xac/0xa10 net/sched/sch_generic.c:941
 qdisc_create.constprop.0+0xce/0x10f0 net/sched/sch_api.c:1211
 tc_modify_qdisc+0x4c5/0x1980 net/sched/sch_api.c:1660
 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5592
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Freed by task 3609:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 kasan_set_track+0x21/0x30 mm/kasan/common.c:45
 kasan_set_free_info+0x20/0x30 mm/kasan/generic.c:370
 ____kasan_slab_free mm/kasan/common.c:366 [inline]
 ____kasan_slab_free+0x130/0x160 mm/kasan/common.c:328
 kasan_slab_free include/linux/kasan.h:236 [inline]
 slab_free_hook mm/slub.c:1728 [inline]
 slab_free_freelist_hook+0x8b/0x1c0 mm/slub.c:1754
 slab_free mm/slub.c:3509 [inline]
 kfree+0xcb/0x280 mm/slub.c:4562
 rcu_do_batch kernel/rcu/tree.c:2527 [inline]
 rcu_core+0x7b8/0x1540 kernel/rcu/tree.c:2778
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558

Last potentially related work creation:
 kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
 __kasan_record_aux_stack+0xbe/0xd0 mm/kasan/generic.c:348
 __call_rcu kernel/rcu/tree.c:3026 [inline]
 call_rcu+0xb1/0x740 kernel/rcu/tree.c:3106
 qdisc_put_unlocked+0x6f/0x90 net/sched/sch_generic.c:1109
 tcf_block_release+0x86/0x90 net/sched/cls_api.c:1238
 tc_new_tfilter+0xc0d/0x2350 net/sched/cls_api.c:2148
 rtnetlink_rcv_msg+0x80d/0xb80 net/core/rtnetlink.c:5583
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x331/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmmsg+0x195/0x470 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

The buggy address belongs to the object at ffff8880985c4800
 which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 776 bytes inside of
 1024-byte region [ffff8880985c4800, ffff8880985c4c00)
The buggy address belongs to the page:
page:ffffea0002617000 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x985c0
head:ffffea0002617000 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 0000000000000000 dead000000000122 ffff888010c41dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 3, migratetype Unmovable, gfp_mask 0x1d20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_HARDWALL), pid 1941, ts 1038999441284, free_ts 1033444432829
 prep_new_page mm/page_alloc.c:2434 [inline]
 get_page_from_freelist+0xa72/0x2f50 mm/page_alloc.c:4165
 __alloc_pages+0x1b2/0x500 mm/page_alloc.c:5389
 alloc_pages+0x1aa/0x310 mm/mempolicy.c:2271
 alloc_slab_page mm/slub.c:1799 [inline]
 allocate_slab mm/slub.c:1944 [inline]
 new_slab+0x28a/0x3b0 mm/slub.c:2004
 ___slab_alloc+0x87c/0xe90 mm/slub.c:3018
 __slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3105
 slab_alloc_node mm/slub.c:3196 [inline]
 slab_alloc mm/slub.c:3238 [inline]
 __kmalloc+0x2fb/0x340 mm/slub.c:4420
 kmalloc include/linux/slab.h:586 [inline]
 kzalloc include/linux/slab.h:715 [inline]
 __register_sysctl_table+0x112/0x1090 fs/proc/proc_sysctl.c:1335
 neigh_sysctl_register+0x2c8/0x5e0 net/core/neighbour.c:3787
 devinet_sysctl_register+0xb1/0x230 net/ipv4/devinet.c:2618
 inetdev_init+0x286/0x580 net/ipv4/devinet.c:278
 inetdev_event+0xa8a/0x15d0 net/ipv4/devinet.c:1532
 notifier_call_chain+0xb5/0x200 kernel/notifier.c:84
 call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1919
 call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
 call_netdevice_notifiers net/core/dev.c:1945 [inline]
 register_netdevice+0x1073/0x1500 net/core/dev.c:9698
 veth_newlink+0x59c/0xa90 drivers/net/veth.c:1722
page last free stack trace:
 reset_page_owner include/linux/page_owner.h:24 [inline]
 free_pages_prepare mm/page_alloc.c:1352 [inline]
 free_pcp_prepare+0x374/0x870 mm/page_alloc.c:1404
 free_unref_page_prepare mm/page_alloc.c:3325 [inline]
 free_unref_page+0x19/0x690 mm/page_alloc.c:3404
 release_pages+0x748/0x1220 mm/swap.c:956
 tlb_batch_pages_flush mm/mmu_gather.c:50 [inline]
 tlb_flush_mmu_free mm/mmu_gather.c:243 [inline]
 tlb_flush_mmu+0xe9/0x6b0 mm/mmu_gather.c:250
 zap_pte_range mm/memory.c:1441 [inline]
 zap_pmd_range mm/memory.c:1490 [inline]
 zap_pud_range mm/memory.c:1519 [inline]
 zap_p4d_range mm/memory.c:1540 [inline]
 unmap_page_range+0x1d1d/0x2a30 mm/memory.c:1561
 unmap_single_vma+0x198/0x310 mm/memory.c:1606
 unmap_vmas+0x16b/0x2f0 mm/memory.c:1638
 exit_mmap+0x201/0x670 mm/mmap.c:3178
 __mmput+0x122/0x4b0 kernel/fork.c:1114
 mmput+0x56/0x60 kernel/fork.c:1135
 exit_mm kernel/exit.c:507 [inline]
 do_exit+0xa3c/0x2a30 kernel/exit.c:793
 do_group_exit+0xd2/0x2f0 kernel/exit.c:935
 __do_sys_exit_group kernel/exit.c:946 [inline]
 __se_sys_exit_group kernel/exit.c:944 [inline]
 __x64_sys_exit_group+0x3a/0x50 kernel/exit.c:944
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Memory state around the buggy address:
 ffff8880985c4a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880985c4a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880985c4b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                      ^
 ffff8880985c4b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8880985c4c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

Fixes: 470502de ("net: sched: unlock rules update API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220131172018.3704490-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Build bot produced a smatch indentation warning,
the code looks correct but it mixes spaces and tabs.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220131211730.3940875-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

A typo in qca808x_read_status means we try to set SMII mode on the port
rather than SGMII when the link speed is not 2.5Gb/s. This results in no
traffic due to the mismatch in configuration between the phy and the
mac.

v2:
 Only change interface mode when the link is up

Fixes: 79c7bc05 ("net: phy: add qca8081 read_status")
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current macsec netdev notify handler handles NETDEV_UNREGISTER event by
releasing relevant SW resources only, this causes resources leak in case
of macsec HW offload, as the underlay driver was not notified to clean
it's macsec offload resources.

Fix by calling the underlay driver to clean it's relevant resources
by moving offload handling from macsec_dellink() to macsec_common_dellink()
when handling NETDEV_UNREGISTER event.

Fixes: 3cf3227a ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/1643542141-28956-1-git-send-email-raeds@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Unlike gmac100, gmac1000, gmac4 has 27 DMA registers and they are
located at DMA_CHAN_BASE_ADDR (0x1100). In order for ethtool to dump
gmac4 DMA registers correctly, this commit checks if a net_device has
gmac4 and uses different logic to dump its DMA registers.

This fixes the following KASAN warning, which can normally be triggered
by a command similar like "ethtool -d eth0":

BUG: KASAN: vmalloc-out-of-bounds in dwmac4_dump_dma_regs+0x6d4/0xb30
Write of size 4 at addr ffffffc010177100 by task ethtool/1839
 kasan_report+0x200/0x21c
 __asan_report_store4_noabort+0x34/0x60
 dwmac4_dump_dma_regs+0x6d4/0xb30
 stmmac_ethtool_gregs+0x110/0x204
 ethtool_get_regs+0x200/0x4b0
 dev_ethtool+0x1dac/0x3800
 dev_ioctl+0x7c0/0xb50
 sock_ioctl+0x298/0x6c4
 ...

Fixes: fbf68229 ("net: stmmac: unify registers dumps methods")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20220131083841.3346801-1-camel.guo@axis.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.

A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.

Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the crash in kernel while dereferencing the NULL pointer,
when the driver is unloaded and simultaneously the VSI rings
are being stopped.

The hardware requires 50msec in order to finish RX queues
disable. For this purpose the driver spins in mdelay function
for the operation to be completed.

For example changing number of queues which requires reset would
fail in the following call stack:

1) i40e_prep_for_reset
2) i40e_pf_quiesce_all_vsi
3) i40e_quiesce_vsi
4) i40e_vsi_close
5) i40e_down
6) i40e_vsi_stop_rings
7) i40e_vsi_control_rx -> disable requires the delay of 50msecs
8) continue back in i40e_down function where
   i40e_clean_tx_ring(vsi->tx_rings[i]) is going to crash

When the driver was spinning vsi_release called
i40e_vsi_free_arrays where the vsi->tx_rings resources
were freed and the pointer was set to NULL.

Fixes: 5b6d4a7f ("i40e: Fix crash during removing i40e driver")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There was an AQ error I40E_AQ_RC_EINVAL when trying
to reset bw limit as part of bw allocation setup.
This was caused by trying to reset bw limit with
DCB enabled. Bw limit should not be reset when
DCB is enabled. The code was relying on the pf->flags
to check if DCB is enabled but if only 1 TC is available
this flag will not be set even though DCB is enabled.
Add a check for number of TC and if it is 1
don't try to reset bw limit even if pf->flags shows
DCB as disabled.

Fixes: fa38e30a ("i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled")
Suggested-by: Alexander Lobakin <alexandr.lobakin@intel.com> # Flatten the condition
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

When we replace TCP with SMC and a fallback occurs, there may be
some socket waitqueue entries remaining in smc socket->wq, such
as eppoll_entries inserted by userspace applications.

After the fallback, data flows over TCP/IP and only clcsocket->wq
will be woken up. Applications can't be notified by the entries
which were inserted in smc socket->wq before fallback. So we need
a mechanism to wake up smc socket->wq at the same time if some
entries remaining in it.

The current workaround is to transfer the entries from smc socket->wq
to clcsock->wq during the fallback. But this may cause a crash
like this:

 general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] PREEMPT SMP PTI
 CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Tainted: G E     5.16.0+ #107
 RIP: 0010:__wake_up_common+0x65/0x170
 Call Trace:
  <IRQ>
  __wake_up_common_lock+0x7a/0xc0
  sock_def_readable+0x3c/0x70
  tcp_data_queue+0x4a7/0xc40
  tcp_rcv_established+0x32f/0x660
  ? sk_filter_trim_cap+0xcb/0x2e0
  tcp_v4_do_rcv+0x10b/0x260
  tcp_v4_rcv+0xd2a/0xde0
  ip_protocol_deliver_rcu+0x3b/0x1d0
  ip_local_deliver_finish+0x54/0x60
  ip_local_deliver+0x6a/0x110
  ? tcp_v4_early_demux+0xa2/0x140
  ? tcp_v4_early_demux+0x10d/0x140
  ip_sublist_rcv_finish+0x49/0x60
  ip_sublist_rcv+0x19d/0x230
  ip_list_rcv+0x13e/0x170
  __netif_receive_skb_list_core+0x1c2/0x240
  netif_receive_skb_list_internal+0x1e6/0x320
  napi_complete_done+0x11d/0x190
  mlx5e_napi_poll+0x163/0x6b0 [mlx5_core]
  __napi_poll+0x3c/0x1b0
  net_rx_action+0x27c/0x300
  __do_softirq+0x114/0x2d2
  irq_exit_rcu+0xb4/0xe0
  common_interrupt+0xba/0xe0
  </IRQ>
  <TASK>

The crash is caused by privately transferring waitqueue entries from
smc socket->wq to clcsock->wq. The owners of these entries, such as
epoll, have no idea that the entries have been transferred to a
different socket wait queue and still use original waitqueue spinlock
(smc socket->wq.wait.lock) to make the entries operation exclusive,
but it doesn't work. The operations to the entries, such as removing
from the waitqueue (now is clcsock->wq after fallback), may cause a
crash when clcsock waitqueue is being iterated over at the moment.

This patch tries to fix this by no longer transferring wait queue
entries privately, but introducing own implementations of clcsock's
callback functions in fallback situation. The callback functions will
forward the wakeup to smc socket->wq if clcsock->wq is actually woken
up and smc socket->wq has remaining entries.

Fixes: 2153bd1e ("net/smc: Transfer remaining wait queue entries during fallback")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two issues with runtime pm handling in stmmac_dvr_remove():

1. the mac is runtime suspended before stopping dma and rx/tx. We
need to ensure the device is properly resumed back.

2. the stmmaceth clk enable/disable isn't balanced in both exit and
error handling code path. Take the exit code path for example, when we
unbind the driver or rmmod the driver module, the mac is runtime
suspended as said above, so the stmmaceth clk is disabled, but
	stmmac_dvr_remove()
	  stmmac_remove_config_dt()
	    clk_disable_unprepare()
CCF will complain this time. The error handling code path suffers
from the similar situtaion.

Here are kernel warnings in error handling code path on Allwinner D1
platform:

[    1.604695] ------------[ cut here ]------------
[    1.609328] bus-emac already disabled
[    1.613015] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:952 clk_core_disable+0xcc/0xec
[    1.621039] CPU: 0 PID: 38 Comm: kworker/u2:1 Not tainted 5.14.0-rc4#1
[    1.627653] Hardware name: Allwinner D1 NeZha (DT)
[    1.632443] Workqueue: events_unbound deferred_probe_work_func
[    1.638286] epc : clk_core_disable+0xcc/0xec
[    1.642561]  ra : clk_core_disable+0xcc/0xec
[    1.646835] epc : ffffffff8023c2ec ra : ffffffff8023c2ec sp : ffffffd00411bb10
[    1.654054]  gp : ffffffff80ec9988 tp : ffffffe00143a800 t0 : ffffffff80ed6a6f
[    1.661272]  t1 : ffffffff80ed6a60 t2 : 0000000000000000 s0 : ffffffe001509e00
[    1.668489]  s1 : 0000000000000001 a0 : 0000000000000019 a1 : ffffffff80e80bd8
[    1.675707]  a2 : 00000000ffffefff a3 : 00000000000000f4 a4 : 0000000000000002
[    1.682924]  a5 : 0000000000000001 a6 : 0000000000000030 a7 : 00000000028f5c29
[    1.690141]  s2 : 0000000000000800 s3 : ffffffe001375000 s4 : ffffffe01fdf7a80
[    1.697358]  s5 : ffffffe001375010 s6 : ffffffff8001fc10 s7 : ffffffffffffffff
[    1.704577]  s8 : 0000000000000001 s9 : ffffffff80ecb248 s10: ffffffe001b80000
[    1.711794]  s11: ffffffe001b80760 t3 : 0000000000000062 t4 : ffffffffffffffff
[    1.719012]  t5 : ffffffff80e0f6d8 t6 : ffffffd00411b8f0
[    1.724321] status: 8000000201800100 badaddr: 0000000000000000 cause: 0000000000000003
[    1.732233] [<ffffffff8023c2ec>] clk_core_disable+0xcc/0xec
[    1.737810] [<ffffffff80240430>] clk_disable+0x38/0x78
[    1.742956] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    1.748451] [<ffffffff8031a500>] stmmac_remove_config_dt+0x1c/0x4c
[    1.754646] [<ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[    1.760484] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    1.765975] [<ffffffff8029a6c8>] platform_probe+0x64/0xf0
[    1.771382] [<ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[    1.777305] [<ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[    1.783402] [<ffffffff8029873c>] driver_probe_device+0x38/0x138
[    1.789324] [<ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[    1.795508] [<ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[    1.802125] [<ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[    1.807701] [<ffffffff80298d1c>] __device_attach+0xd8/0x184
[    1.813277] [<ffffffff802967b0>] bus_probe_device+0x98/0xbc
[    1.818852] [<ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[    1.825122] [<ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[    1.830872] [<ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[    1.836362] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    1.841335] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    1.846304] [<ffffffff8001fa60>] process_one_work+0x38c/0x390
[    1.852054] [<ffffffff80026564>] kthread+0x124/0x160
[    1.857021] [<ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[    1.862770] [<ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[    1.868956] ---[ end trace 8d5c6046255f84a0 ]---
[    1.873675] ------------[ cut here ]------------
[    1.878366] bus-emac already unprepared
[    1.882378] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:810 clk_core_unprepare+0xe4/0x168
[    1.890673] CPU: 0 PID: 38 Comm: kworker/u2:1 Tainted: G        W	5.14.0-rc4 #1
[    1.898674] Hardware name: Allwinner D1 NeZha (DT)
[    1.903464] Workqueue: events_unbound deferred_probe_work_func
[    1.909305] epc : clk_core_unprepare+0xe4/0x168
[    1.913840]  ra : clk_core_unprepare+0xe4/0x168
[    1.918375] epc : ffffffff8023d6cc ra : ffffffff8023d6cc sp : ffffffd00411bb10
[    1.925593]  gp : ffffffff80ec9988 tp : ffffffe00143a800 t0 : 0000000000000002
[    1.932811]  t1 : ffffffe01f743be0 t2 : 0000000000000040 s0 : ffffffe001509e00
[    1.940029]  s1 : 0000000000000001 a0 : 000000000000001b a1 : ffffffe00143a800
[    1.947246]  a2 : 0000000000000000 a3 : 00000000000000f4 a4 : 0000000000000001
[    1.954463]  a5 : 0000000000000000 a6 : 0000000005fce2a5 a7 : 0000000000000001
[    1.961680]  s2 : 0000000000000800 s3 : ffffffff80afeb90 s4 : ffffffe01fdf7a80
[    1.968898]  s5 : ffffffe001375010 s6 : ffffffff8001fc10 s7 : ffffffffffffffff
[    1.976115]  s8 : 0000000000000001 s9 : ffffffff80ecb248 s10: ffffffe001b80000
[    1.983333]  s11: ffffffe001b80760 t3 : ffffffff80b39120 t4 : 0000000000000001
[    1.990550]  t5 : 0000000000000000 t6 : ffffffe001600002
[    1.995859] status: 8000000201800120 badaddr: 0000000000000000 cause: 0000000000000003
[    2.003771] [<ffffffff8023d6cc>] clk_core_unprepare+0xe4/0x168
[    2.009609] [<ffffffff802403a0>] clk_unprepare+0x24/0x3c
[    2.014929] [<ffffffff8031a508>] stmmac_remove_config_dt+0x24/0x4c
[    2.021125] [<ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[    2.026965] [<ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[    2.032463] [<ffffffff8029a6c8>] platform_probe+0x64/0xf0
[    2.037871] [<ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[    2.043795] [<ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[    2.049892] [<ffffffff8029873c>] driver_probe_device+0x38/0x138
[    2.055815] [<ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[    2.061999] [<ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[    2.068616] [<ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[    2.074193] [<ffffffff80298d1c>] __device_attach+0xd8/0x184
[    2.079769] [<ffffffff802967b0>] bus_probe_device+0x98/0xbc
[    2.085345] [<ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[    2.091616] [<ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[    2.097367] [<ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[    2.102858] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    2.107830] [<ffffffff80026bf4>] kthreadd+0x94/0x188
[    2.112800] [<ffffffff8001fa60>] process_one_work+0x38c/0x390
[    2.118551] [<ffffffff80026564>] kthread+0x124/0x160
[    2.123520] [<ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[    2.129268] [<ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[    2.135455] ---[ end trace 8d5c6046255f84a1 ]---

Fixes: 5ec55823 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'ieee802154-for-net-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2022-01-28

An update from ieee802154 for your *net* tree.

A bunch of fixes in drivers, all from Miquel Raynal.
Clarifying the default channel in hwsim, leak fixes in at86rf230 and ca8210 as
well as a symbol duration fix for mcr20a. Topping up the driver fixes with
better error codes in nl802154 and a cleanup in MAINTAINERS for an orphaned
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'tail' and 'head' are 'unsigned int' type free-running count, when
'head' is overflow, the 'int i (= tail) < u32 head' will be false:

Only '- loop 0: idx = 63' result is shown, so it needs to use 'int' type
to compare, it can handle the overflow correctly.

typedef uint32_t u32;

int main()
{
        u32 tail, head;
        int stail, shead;
        int i, loop;

        tail = 0xffffffff;
        head = 0x00000000;

        for (i = tail, loop = 0; i < head; i++) {
                unsigned int idx = i & 63;

                printf("+ loop %d: idx = %u\n", loop++, idx);
        }

        stail = tail;
        shead = head;
        for (i = stail, loop = 0; i < shead; i++) {
                unsigned int idx = i & 63;

                printf("- loop %d: idx = %u\n", loop++, idx);
        }

        return 0;
}

Fixes: 5cdad90d ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Duoming Zhou says:

====================
ax25: fix NPD and UAF bugs when detaching ax25 device

There are NPD and UAF bugs when detaching ax25 device, we
use lock and refcount to mitigate these bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If we dereference ax25_dev after we call kfree(ax25_dev) in
ax25_dev_device_down(), it will lead to concurrency UAF bugs.
There are eight syscall functions suffer from UAF bugs, include
ax25_bind(), ax25_release(), ax25_connect(), ax25_ioctl(),
ax25_getname(), ax25_sendmsg(), ax25_getsockopt() and
ax25_info_show().

One of the concurrency UAF can be shown as below:

  (USE)                       |    (FREE)
                              |  ax25_device_event
                              |    ax25_dev_device_down
ax25_bind                     |    ...
  ...                         |      kfree(ax25_dev)
  ax25_fillin_cb()            |    ...
    ax25_fillin_cb_from_dev() |
  ...                         |

The root cause of UAF bugs is that kfree(ax25_dev) in
ax25_dev_device_down() is not protected by any locks.
When ax25_dev, which there are still pointers point to,
is released, the concurrency UAF bug will happen.

This patch introduces refcount into ax25_dev in order to
guarantee that there are no pointers point to it when ax25_dev
is released.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous commit 1ade48d0 ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.

The NULL pointer dereference bug can be shown as below:

ax25_kill_by_device()        | ax25_release()
                             |   ax25_destroy_socket()
                             |     ax25_cb_del()
  ...                        |     ...
                             |     ax25->sk=NULL;
  lock_sock(s->sk); //(1)    |
  s->ax25_dev = NULL;        |     ...
  release_sock(s->sk); //(2) |
  ...                        |

The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.

The concurrency UAF bug can be shown as below:

ax25_kill_by_device()        | ax25_release()
                             |   ax25_destroy_socket()
  ...                        |   ...
                             |   sock_put(sk); //FREE
  lock_sock(s->sk); //(1)    |
  s->ax25_dev = NULL;        |   ...
  release_sock(s->sk); //(2) |
  ...                        |

The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable clk_sel_val is not initialized in the default case of the first switch statement.
In that case, the function should return immediately without any changes to the hardware.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b38dd98f ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure to reset the tx_timer_active flag in xgbe_stop(),
otherwise a port restart may result in tx timeout due to
uncleared flag.

Fixes: c635eaac ("amd-xgbe: Remove Tx coalescing")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127060222.453371-1-Raju.Rangoju@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Remove leftovers from flowtable modules, from Geert Uytterhoeven.

2) Missing refcount increment of conntrack template in nft_ct,
   from Florian Westphal.

3) Reduce nft_zone selftest time, also from Florian.

4) Add selftest to cover stateless NAT on fragments, from Florian Westphal.

5) Do not set net_device when for reject packets from the bridge path,
   from Phil Sutter.

6) Cancel register tracking info on nft_byteorder operations.

7) Extend nft_concat_range selftest to cover set reload with no elements,
   from Florian Westphal.

8) Remove useless update of pointer in chain blob builder, reported
   by kbuild test robot.

* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
  netfilter: nf_tables: remove assignment with no effect in chain blob builder
  selftests: nft_concat_range: add test for reload with no element add/del
  netfilter: nft_byteorder: track register operations
  netfilter: nft_reject_bridge: Fix for missing reply from prerouting
  selftests: netfilter: check stateless nat udp checksum fixup
  selftests: netfilter: reduce zone stress test running time
  netfilter: nft_ct: fix use after free when attaching zone template
  netfilter: Remove flowtable relics
====================

Link: https://lore.kernel.org/r/20220127235235.656931-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There will be BUG_ON() triggered in include/linux/skbuff.h leading to
intermittent kernel panic, when the skb length underflow is detected.

Fix this by dropping the packet if such length underflows are seen
because of inconsistencies in the hardware descriptors.

Fixes: 622c36f1 ("amd-xgbe: Fix jumbo MTU processing on newer hardware")
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127092003.2812745-1-Shyam-sundar.S-k@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from netfilter and can.

  Current release - new code bugs:

   - tcp: add a missing sk_defer_free_flush() in tcp_splice_read()

   - tcp: add a stub for sk_defer_free_flush(), fix CONFIG_INET=n

   - nf_tables: set last expression in register tracking area

   - nft_connlimit: fix memleak if nf_ct_netns_get() fails

   - mptcp: fix removing ids bitmap setting

   - bonding: use rcu_dereference_rtnl when getting active slave

   - fix three cases of sleep in atomic context in drivers: lan966x, gve

   - handful of build fixes for esoteric drivers after netdev->dev_addr
     was made const

  Previous releases - regressions:

   - revert "ipv6: Honor all IPv6 PIO Valid Lifetime values", it broke
     Linux compatibility with USGv6 tests

   - procfs: show net device bound packet types

   - ipv4: fix ip option filtering for locally generated fragments

   - phy: broadcom: hook up soft_reset for BCM54616S

  Previous releases - always broken:

   - ipv4: raw: lock the socket in raw_bind()

   - ipv4: decrease the use of shared IPID generator to decrease the
     chance of attackers guessing the values

   - procfs: fix cross-netns information leakage in /proc/net/ptype

   - ethtool: fix link extended state for big endian

   - bridge: vlan: fix single net device option dumping

   - ping: fix the sk_bound_dev_if match in ping_lookup"

* tag 'net-5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
  net: bridge: vlan: fix memory leak in __allowed_ingress
  net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
  ipv4: remove sparse error in ip_neigh_gw4()
  ipv4: avoid using shared IP generator for connected sockets
  ipv4: tcp: send zero IPID in SYNACK messages
  ipv4: raw: lock the socket in raw_bind()
  MAINTAINERS: add missing IPv4/IPv6 header paths
  MAINTAINERS: add more files to eth PHY
  net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
  net: bridge: vlan: fix single net device option dumping
  net: stmmac: skip only stmmac_ptp_register when resume from suspend
  net: stmmac: configure PTP clock source prior to PTP initialization
  Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
  connector/cn_proc: Use task_is_in_init_pid_ns()
  pid: Introduce helper task_is_in_init_pid_ns()
  gve: Fix GFP flags when allocing pages
  net: lan966x: Fix sleep in atomic context when updating MAC table
  net: lan966x: Fix sleep in atomic context when injecting frames
  ethernet: seeq/ether3: don't write directly to netdev->dev_addr
  ethernet: 8390/etherh: don't write directly to netdev->dev_addr
  ...

When using per-vlan state, if vlan snooping and stats are disabled,
untagged or priority-tagged ingress frame will go to check pvid state.
If the port state is forwarding and the pvid state is not
learning/forwarding, untagged or priority-tagged frame will be dropped
but skb memory is not freed.
Should free skb when __allowed_ingress returns false.

Fixes: a580c76d ("net: bridge: vlan: add per-vlan state")
Signed-off-by: Tim Yi <tim.yi@pica8.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220127074953.12632-1-tim.yi@pica8.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

cppcheck possible warnings:

>> net/netfilter/nf_tables_api.c:2014:2: warning: Assignment of function parameter has no effect outside the function. Did you forget dereferencing it? [uselessAssignmentPtrArg]
    ptr += offsetof(struct nft_rule_dp, data);
    ^
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Rename SKB_DROP_REASON_SOCKET_FILTER, which is used
as the reason of skb drop out of socket filter before
it's part of a released kernel. It will be used for
more protocols than just TCP in future series.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/all/20220127091308.91401-2-imagedong@tencent.com/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

./include/net/route.h:373:48: warning: incorrect type in argument 2 (different base types)
./include/net/route.h:373:48:    expected unsigned int [usertype] key
./include/net/route.h:373:48:    got restricted __be32 [usertype] daddr

Fixes: 5c9f7c1d ("ipv4: Add helpers for neigh lookup for nexthop")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220127013404.1279313-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>