- 26 Apr, 2018 17 commits
-
-
NeilBrown authored
[ Upstream commit dce2630c ] There are 2 comments in the NFSv4 code which suggest that SIGLOST should possibly be sent to a process. In these cases a lock has been lost. The current practice is to set NFS_LOCK_LOST so that read/write returns EIO when a lock is lost. So change these comments to code when sets NFS_LOCK_LOST. One case is when lock recovery after apparent server restart fails with NFS4ERR_DENIED, NFS4ERR_RECLAIM_BAD, or NFS4ERRO_RECLAIM_CONFLICT. The other case is when a lock attempt as part of lease recovery fails with NFS4ERR_DENIED. In an ideal world, these should not happen. However I have a packet trace showing an NFSv4.1 session getting NFS4ERR_BADSESSION after an extended network parition. The NFSv4.1 client treats this like server reboot until/unless it get NFS4ERR_NO_GRACE, in which case it switches over to "nograce" recovery mode. In this network trace, the client attempts to recover a lock and the server (incorrectly) reports NFS4ERR_DENIED rather than NFS4ERR_NO_GRACE. This leads to the ineffective comment and the client then continues to write using the OPEN stateid. Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Zijlstra authored
[ Upstream commit 30c7e5b1 ] Zhang Rui reported that a Surface Pro 4 will fail to boot with lapic=notscdeadline. Part of the problem is that that machine doesn't have a PIT. If, for some reason, the TSC init has to fall back to TSC calibration, it relies on the PIT to be present. Allow TSC calibration to reliably fall back to HPET. The below results in an accurate TSC measurement when forced on a IVB: tsc: Unable to calibrate against PIT tsc: No reference (HPET/PMTIMER) available tsc: Unable to calibrate against PIT tsc: using HPET reference calibration tsc: Detected 2792.451 MHz processor Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: len.brown@intel.com Cc: rui.zhang@intel.com Link: https://lkml.kernel.org/r/20171222092243.333145937@infradead.orgSigned-off-by:
-
Hector Martin authored
[ Upstream commit 18877518 ] At least some JMicron controllers issue buggy oversized DMA reads when fetching context descriptors, always fetching 0x20 bytes at once for descriptors which are only 0x10 bytes long. This is often harmless, but can cause page faults on modern systems with IOMMUs: DMAR: [DMA Read] Request device [05:00.0] fault addr fff56000 [fault reason 06] PTE Read access is not set firewire_ohci 0000:05:00.0: DMA context IT0 has stopped, error code: evt_descriptor_read This works around the problem by always leaving 0x10 padding bytes at the end of descriptor buffer pages, which should be harmless to do unconditionally for controllers in case others have the same behavior. Signed-off-by:
Hector Martin <marcan@marcan.st> Reviewed-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Merlijn Wajer authored
commit 94e46a4f upstream. This fixes an oops on unbind / module unload (on the musb omap2430 platform). musb_remove function now calls musb_platform_exit before disabling runtime pm. Signed-off-by:
Merlijn Wajer <merlijn@wizzup.org> Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Merlijn Wajer authored
commit df6b074d upstream. Without pm_runtime_{get,put}_sync calls in place, reading vbus status via /sys causes the following error: Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060 pgd = b333e822 [fa0ab060] *pgd=48011452(bad) [<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4) [<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44) [<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc) [<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448) [<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118) [<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144) [<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74) [<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54) Solution was suggested by Tony Lindgren <tony@atomide.com>. Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Andreas Kemnade authored
commit 17539f2f upstream. On dm3730 there are enumeration problems after resume. Investigation led to the cause that the MUSB_POWER_SOFTCONN bit is not set. If it was set before suspend (because it was enabled via musb_pullup()), it is set in musb_restore_context() so the pullup is enabled. But then musb_start() is called which overwrites MUSB_POWER and therefore disables MUSB_POWER_SOFTCONN, so no pullup is enabled and the device is not enumerated. So let's do a subset of what musb_start() does in the same way as musb_suspend() does it. Platform-specific stuff it still called as there might be some phy-related stuff which needs to be enabled. Also interrupts are enabled, as it was the original idea of calling musb_start() in musb_resume() according to Commit 6fc6f4b8 ("usb: musb: Disable interrupts on suspend, enable them on resume") Signed-off-by:
Andreas Kemnade <andreas@kemnade.info> Tested-by:
-
Imre Deak authored
commit 5e1df40f upstream. Currently we see sporadic timeouts during CDCLK changing both on BXT and GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by changing the frequency in a tight loop after blanking the display. The upper bound for the completion time is 800us based on my tests, so increase it from the current 500us to 2ms; with that I couldn't trigger the problem either on BXT or GLK. Note that timeouts happened during both the change notification and the voltage level setting PCODE request. (For the latter one BSpec doesn't require us to wait for completion before further HW programming.) This issue is similar to commit 2c7d0602 ("drm/i915/gen9: Fix PCODE polling during CDCLK change notification") but there the PCODE request does complete (as shown by the mbox busy flag), only the reply we get from PCODE indicates a failure. So there we keep resending the request until a success reply, here we just have to increase the timeout for the one PCODE request we send. v2: - s/snb_pcode_request/sandybridge_pcode_write_timeout/ (Ville) Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.4+ Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com (cherry picked from commit e76019a8) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> (Rebased for v4.14 stable tree due to upstream cdclk_state and pcu_lock change) Signed-off-by:
-
Imre Deak authored
commit 7eb2c4dd upstream. LSPCON adapters in low-power state may ignore the first I2C write during TMDS output buffer enabling, resulting in a blank screen even with an otherwise enabled pipe. Fix this by reading back and validating the written value a few times. The problem was noticed on GLK machines with an onboard LSPCON adapter after entering/exiting DC5 power state. Doing an I2C read of the adapter ID as the first transaction - instead of the I2C write to enable the TMDS buffers - returns the correct value. Based on this we assume that the transaction itself is sent properly, it's only the adapter that is not ready for some reason to accept this first write after waking from low-power state. In my case the second I2C write attempt always succeeded. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105854 Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180416155309.11100-1-imre.deak@intel.comSigned-off-by:
-
Xidong Wang authored
commit fcf1fadf upstream. Along the eb_lookup_vmas() error path, the return value from kmem_cache_alloc() was freed using kfree(). Fix it to use the proper kmem_cache_free() instead. Fixes: d1b48c1e ("drm/i915: Replace execbuf vma ht with an idr") Signed-off-by:
Xidong Wang <wangxidong_97@163.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v4.14+ Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by:
-
Gaurav K Singh authored
commit b4615730 upstream. On Geminilake, sometimes audio card is not getting detected after reboot. This is a spurious issue happening on Geminilake. HW codec and HD audio controller link was going out of sync for which there was a fix in i915 driver but was not getting invoked for GLK. Extending this fix to GLK as well. Tested by Du,Wenkai on GLK board. Bspec: 21829 v2: Instead of checking GEN9_BC, BXT and GLK macros, use IS_GEN9 macro (Jani N) Cc: <stable@vger.kernel.org> # b651bd2a ("drm/i915/audio: Fix audio enumeration issue on BXT") Cc: <stable@vger.kernel.org> Signed-off-by:
Gaurav K Singh <gaurav.k.singh@intel.com> Reviewed-by:
Abhay Kumar <abhay.Kumar@intel.com> Signed-off-by:
-
Gerd Hoffmann authored
commit 9f591ae6 upstream. On unknown/unhandled ioctls the driver should return an error, so userspace knows it tried to use something unsupported. Cc: stable@vger.kernel.org Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by:
-
Daniel J Blueman authored
commit c0db1b67 upstream. During BO teardown, an indirect list 'uniform_addr_offsets' wasn't being freed leading to leaking many 128B allocations. Fix the memory leak by releasing it at teardown time. Cc: stable@vger.kernel.org Fixes: 6d45c81d ("drm/vc4: Add support for branching in shader validation.") Signed-off-by:
Daniel J Blueman <daniel@quora.org> Signed-off-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
-
Xiaoming Gao authored
commit d3878e16 upstream. The TSC calibration code uses HPET as reference. The conversion normalizes the delta of two HPET timestamps: hpetref = ((tshpet1 - tshpet2) * HPET_PERIOD) / 1e6 and then divides the normalized delta of the corresponding TSC timestamps by the result to calulate the TSC frequency. tscfreq = ((tstsc1 - tstsc2 ) * 1e6) / hpetref This uses do_div() which takes an u32 as the divisor, which worked so far because the HPET frequency was low enough that 'hpetref' never exceeded 32bit. On Skylake machines the HPET frequency increased so 'hpetref' can exceed 32bit. do_div() truncates the divisor, which causes the calibration to fail. Use div64_u64() to avoid the problem. [ tglx: Fixes whitespace mangled patch and rewrote changelog ] Signed-off-by:
Xiaoming Gao <newtongao@tencent.com> Signed-off-by:
-
Anson Huang authored
commit 74071884 upstream. The additional brakects added to tpm_set_next_event's return value computation causes (int) forced type conversion NOT taking effect, and the incorrect value return will cause various system timer issue, like RCU stall etc.. Remove the additional brackets to make sure tpm_set_next_event always returns correct value. Fixes: 059ab7b8 ("clocksource/drivers/imx-tpm: Add imx tpm timer support") Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Signed-off-by:
Dong Aisheng <Aisheng.dong@nxp.com> Cc: stable@vger.kernel.org Cc: daniel.lezcano@linaro.org Cc: Linux-imx@nxp.com Link: https://lkml.kernel.org/r/1524117883-2484-1-git-send-email-Anson.Huang@nxp.comSigned-off-by:
-
Dou Liyang authored
commit 10daf10a upstream. RongQing reported that there are some X2APIC id 0xffffffff in his machine's ACPI MADT table, which makes the number of possible CPU inaccurate. The reason is that the ACPI X2APIC parser has no sanity check for APIC ID 0xffffffff, which is an invalid id in all APIC types. See "Intel
® 64 Architecture x2APIC Specification", Chapter 2.4.1. Add a sanity check to acpi_parse_x2apic() which ignores the invalid id. Reported-by:Li RongQing <lirongqing@baidu.com> Signed-off-by:
Dou Liyang <douly.fnst@cn.fujitsu.com> Signed-off-by:
-
David Sterba authored
commit 92d32170 upstream. The last update to readdir introduced a temporary buffer to store the emitted readdir data, but as there are file names of variable length, there's a lot of unaligned access. This was observed on a sparc64 machine: Kernel unaligned access at TPC[102f3080] btrfs_real_readdir+0x51c/0x718 [btrfs] Fixes: 23b5ec74 ("btrfs: fix readdir deadlock with pagefault") CC: stable@vger.kernel.org # 4.14+ Reported-and-tested-by:
René Rebe <rene@exactcode.com> Reviewed-by:
Liu Bo <bo.liu@linux.alibaba.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Steve French authored
commit 1d0cffa6 upstream. RHBZ: 1453123 Since at least the 3.10 kernel and likely a lot earlier we have not been able to create unix domain sockets in a cifs share when mounted using the SFU mount option (except when mounted with the cifs unix extensions to Samba e.g.) Trying to create a socket, for example using the af_unix command from xfstests will cause : BUG: unable to handle kernel NULL pointer dereference at 00000000 00000040 Since no one uses or depends on being able to create unix domains sockets on a cifs share the easiest fix to stop this vulnerability is to simply not allow creation of any other special files than char or block devices when sfu is used. Added update to Ronnie's patch to handle a tcon link leak, and to address a buf leak noticed by Gustavo and Colin. Acked-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> CC: Colin Ian King <colin.king@canonical.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Reported-by:
Eryu Guan <eguan@redhat.com> Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <smfrench@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
- 24 Apr, 2018 23 commits
-
-
Greg Kroah-Hartman authored
-
Greg Thelen authored
commit 2e898e4c upstream. lock_page_memcg()/unlock_page_memcg() use spin_lock_irqsave/restore() if the page's memcg is undergoing move accounting, which occurs when a process leaves its memcg for a new one that has memory.move_charge_at_immigrate set. unlocked_inode_to_wb_begin,end() use spin_lock_irq/spin_unlock_irq() if the given inode is switching writeback domains. Switches occur when enough writes are issued from a new domain. This existing pattern is thus suspicious: lock_page_memcg(page); unlocked_inode_to_wb_begin(inode, &locked); ... unlocked_inode_to_wb_end(inode, locked); unlock_page_memcg(page); If both inode switch and process memcg migration are both in-flight then unlocked_inode_to_wb_end() will unconditionally enable interrupts while still holding the lock_page_memcg() irq spinlock. This suggests the possibility of deadlock if an interrupt occurs before unlock_page_memcg(). truncate __cancel_dirty_page lock_page_memcg unlocked_inode_to_wb_begin unlocked_inode_to_wb_end <interrupts mistakenly enabled> <interrupt> end_page_writeback test_clear_page_writeback lock_page_memcg <deadlock> unlock_page_memcg Due to configuration limitations this deadlock is not currently possible because we don't mix cgroup writeback (a cgroupv2 feature) and memory.move_charge_at_immigrate (a cgroupv1 feature). If the kernel is hacked to always claim inode switching and memcg moving_account, then this script triggers lockup in less than a minute: cd /mnt/cgroup/memory mkdir a b echo 1 > a/memory.move_charge_at_immigrate echo 1 > b/memory.move_charge_at_immigrate ( echo $BASHPID > a/cgroup.procs while true; do dd if=/dev/zero of=/mnt/big bs=1M count=256 done ) & while true; do sync done & sleep 1h & SLEEP=$! while true; do echo $SLEEP > a/cgroup.procs echo $SLEEP > b/cgroup.procs done The deadlock does not seem possible, so it's debatable if there's any reason to modify the kernel. I suggest we should to prevent future surprises. And Wang Long said "this deadlock occurs three times in our environment", so there's more reason to apply this, even to stable. Stable 4.4 has minor conflicts applying this patch. For a clean 4.4 patch see "[PATCH for-4.4] writeback: safer lock nesting" https://lkml.org/lkml/2018/4/11/146 Wang Long said "this deadlock occurs three times in our environment" [gthelen@google.com: v4] Link: http://lkml.kernel.org/r/20180411084653.254724-1-gthelen@google.com [akpm@linux-foundation.org: comment tweaks, struct initialization simplification] Change-Id: Ibb773e8045852978f6207074491d262f1b3fb613 Link: http://lkml.kernel.org/r/20180410005908.167976-1-gthelen@google.com Fixes: 682aa8e1 ("writeback: implement unlocked_inode_to_wb transaction and use it for stat updates") Signed-off-by:
Greg Thelen <gthelen@google.com> Reported-by:
Wang Long <wanglong19@meituan.com> Acked-by:
Michal Hocko <mhocko@suse.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: <stable@vger.kernel.org> [v4.2+] Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [natechancellor: Adjust context due to lack of b93b0163] Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Sean Young authored
[not upstream as the driver is deleted in 4.16 - gregkh] Whenever poll is called, the reference count is increased but never decreased. This means that on rmmod, the lirc_thread is not stopped, and will trample over freed memory. Zilog/Hauppauge IR driver unloaded BUG: unable to handle kernel paging request at ffffffffc17ba640 Oops: 0010 [#1] SMP CPU: 1 PID: 667 Comm: zilog-rx-i2c-1 Tainted: P C OE 4.13.16-302.fc27.x86_64 #1 Hardware name: Gigabyte Technology Co., Ltd. GA-MA790FXT-UD5P/GA-MA790FXT-UD5P, BIOS F6 08/06/2009 task: ffff964eb452ca00 task.stack: ffffb254414dc000 RIP: 0010:0xffffffffc17ba640 RSP: 0018:ffffb254414dfe78 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff964ec1b35890 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 RBP: ffffb254414dff00 R08: 000000000000036e R09: ffff964ecfc8dfd0 R10: ffffb254414dfe78 R11: 00000000000f4240 R12: ffff964ec2bf28a0 R13: ffff964ec1b358a8 R14: ffff964ec1b358d0 R15: ffff964ec1b35800 FS: 0000000000000000(0000) GS:ffff964ecfc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffc17ba640 CR3: 000000023058c000 CR4: 00000000000006e0 Call Trace: kthread+0x125/0x140 ? kthread_park+0x60/0x60 ? do_syscall_64+0x67/0x140 ret_from_fork+0x25/0x30 Code: Bad RIP value. RIP: 0xffffffffc17ba640 RSP: ffffb254414dfe78 CR2: ffffffffc17ba640 Note that zilog-rx-i2c-1 should have exited by now, but hasn't due to the missing put in poll(). This code has been replaced completely in kernel v4.16 by a new driver, see commit acaa34bf ("media: rc: implement zilog transmitter"), and commit f95367a7 ("media: staging: remove lirc_zilog driver"). Cc: stable@vger.kernel.org # v4.15- (all up to and including v4.15) Reported-by:
Warren Sturm <warren.sturm@gmail.com> Tested-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
[not upstream as the driver is deleted in 4.16 - gregkh] The lirc config documented here https://www.blushingpenguin.com/mark/blog/?p=24 uses raw_codes for sending IR. Each key only has one pulse, which in fact is an index into the haup-ir-blaster.bin file. Changing the driver to LIRCCODE (although more accurate) breaks this configuration. This code has been replaced completely in kernel v4.16 by a new driver, see commit acaa34bf ("media: rc: implement zilog transmitter"), and commit f95367a7 ("media: staging: remove lirc_zilog driver"). This reverts commit 89d8a2cc. Fixes: 615cd3fe ("[media] media: lirc_dev: make better use of file->private_data") Cc: stable@vger.kernel.org # v4.14-v4.15 Reported-by:
-
Luca Coelho authored
commit 9e5053ad upstream. A lot of new PCI IDs were added for the 9000 series. Add them to the list of supported PCI IDs. Cc: stable@vger.kernel.org # 4.13+ Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Luca Coelho authored
commit 86a2b204 upstream. Some devices use a shared clock which is very sensitive to variations and cause trouble in some situations. We need to set a bit in the phy configuration to indicate that to the FW. To make this generic, add a extra_phy_config_flags element to the device configuration and OR it into the phy_cfg before sending it to the firmware. And also create a set of configurations for devices that use shared clocks and need this extra bit to be set. Fixes: c62446d2 ("iwlwifi: add new 9460 series PCI IDs") Signed-off-by:
-
Andrew Lunn authored
commit fc5f3376 upstream. The Marvell switches under some conditions will pass a frame to the host with the port being the CPU port. Such frames are invalid, and should be dropped. Not dropping them can result in a crash when incrementing the receive statistics for an invalid port. This has been reworked for 4.14, which does not have the central dsa_master_find_slave() function, so each tag driver needs to check. Reported-by:
Chris Healy <cphealy@gmail.com> Fixes: 91da11f8 ("net: Distributed Switch Architecture protocol support") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Matthew Wilcox authored
commit abc1be13 upstream. f2fs specifies the __GFP_ZERO flag for allocating some of its pages. Unfortunately, the page cache also uses the mapping's GFP flags for allocating radix tree nodes. It always masked off the __GFP_HIGHMEM flag, and masks off __GFP_ZERO in some paths, but not all. That causes radix tree nodes to be allocated with a NULL list_head, which causes backtraces like: __list_del_entry+0x30/0xd0 list_lru_del+0xac/0x1ac page_cache_tree_insert+0xd8/0x110 The __GFP_DMA and __GFP_DMA32 flags would also be able to sneak through if they are ever used. Fix them all by using GFP_RECLAIM_MASK at the innermost location, and remove it from earlier in the callchain. Link: http://lkml.kernel.org/r/20180411060320.14458-2-willy@infradead.org Fixes: 449dd698 ("mm: keep page cache radix tree nodes in check") Signed-off-by:
Matthew Wilcox <mawilcox@microsoft.com> Reported-by:
Chris Fries <cfries@google.com> Debugged-by:
Minchan Kim <minchan@kernel.org> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Jan Kara <jack@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ian Kent authored
commit 1e630665 upstream. The autofs file system mkdir inode operation blindly sets the created directory mode to S_IFDIR | 0555, ingoring the passed in mode, which can cause selinux dac_override denials. But the function also checks if the caller is the daemon (as no-one else should be able to do anything here) so there's no point in not honouring the passed in mode, allowing the daemon to set appropriate mode when required. Link: http://lkml.kernel.org/r/152361593601.8051.14014139124905996173.stgit@pluto.themaw.netSigned-off-by:
Ian Kent <raven@themaw.net> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Al Viro authored
commit 16a34adb upstream. We want it only for the stuff created by SB_KERNMOUNT mounts, *not* for their copies. As it is, creating a deep stack of bindings of /proc/*/ns/* somewhere in a new namespace and exiting yields a stack overflow. Cc: stable@kernel.org Reported-by:
Alexander Aring <aring@mojatatu.com> Bisected-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Tested-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 4a3877c4 upstream. if we ever hit rpc_gssd_dummy_depopulate() dentry passed to it has refcount equal to 1. __rpc_rmpipe() drops it and dput() done after that hits an already freed dentry. Cc: stable@kernel.org Signed-off-by:
-
Al Viro authored
commit 65903842 upstream. orangefs_fill_sb() might've failed to allocate ORANGEFS_SB(s); don't oops in that case. Cc: stable@kernel.org Signed-off-by:
-
Al Viro authored
commit a24cd490 upstream. hypfs_fill_super() might fail to allocate sbi; hypfs_kill_super() should not oops on that. Cc: stable@vger.kernel.org Signed-off-by:
-
Al Viro authored
commit c66b23c2 upstream. jffs2_fill_super() might fail to allocate jffs2_sb_info; jffs2_kill_sb() must survive that. Cc: stable@kernel.org Signed-off-by:
-
Ville Syrjälä authored
commit 5deae919 upstream. Turns out the VLV/CHV fixed function sprite CSC expects full range data as input. We've been feeding it limited range data to it all along. To expand the data out to full range we'll use the color correction registers (brightness, contrast, and saturation). On CHV pipe B we were actually doing the right thing already because we progammed the custom CSC matrix to do expect limited range input. Now that well pre-expand the data out with the color correction unit, we need to change the CSC matrix to operate with full range input instead. This should make the sprite output of the other pipes match the sprite output of pipe B reasonably well. Looking at the resulting pipe CRCs, there can be a slight difference in the output, but as I don't know the formula used by the fixed function CSC of the other pipes, I don't think it's worth the effort to try to match the output exactly. It might not even be possible due to difference in internal precision etc. One slight caveat here is that the color correction registers are single bufferred, so we should really be updating them during vblank, but we still don't have a mechanism for that, so just toss in another FIXME. v2: Rebase v3: s/bri/brightness/ s/con/contrast/ (Shashank) v4: Clarify the constants and math (Shashank) Cc: Harry Wentland <harry.wentland@amd.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Daniel Stone <daniel@fooishbar.org> Cc: Russell King - ARM Linux <linux@armlinux.org.uk> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Cc: Hans Verkuil <hverkuil@xs4all.nl> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Jyri Sarha <jsarha@ti.com> Cc: "Tang, Jun" <jun.tang@intel.com> Reported-by:
"Tang, Jun" <jun.tang@intel.com> Cc: stable@vger.kernel.org Fixes: 7f1f3851 ("drm/i915: sprite support for ValleyView v4") Reviewed-by:
Shashank Sharma <shashank.sharma@intel.com> Signed-off-by:
-
Daniel Kurtz authored
commit 300ad899 upstream. Commit c31165d7 ("mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1") added a HS200 tuning method for use with AMD SDHCI controllers. As described in the commit subject, this tuning is specific for HS200. However, as implemented, this method is used for all host timings, because platform_execute_tuning, if it exists, is called unconditionally by sdhci_execute_tuning(). This breaks tuning when using the AMD controller with, for example, a DDR50 SD card. Instead, we can implement an amd execute_tuning wrapper callback, and then conditionally do the HS200 specific tuning for HS200, and otherwise call back to the standard sdhci_execute_tuning(). Signed-off-by:
Daniel Kurtz <djkurtz@chromium.org> Acked-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Fixes: c31165d7 ("mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Amir Goldstein authored
commit 54a307ba upstream. When event on child inodes are sent to the parent inode mark and parent inode mark was not marked with FAN_EVENT_ON_CHILD, the event will not be delivered to the listener process. However, if the same process also has a mount mark, the event to the parent inode will be delivered regadless of the mount mark mask. This behavior is incorrect in the case where the mount mark mask does not contain the specific event type. For example, the process adds a mark on a directory with mask FAN_MODIFY (without FAN_EVENT_ON_CHILD) and a mount mark with mask FAN_CLOSE_NOWRITE (without FAN_ONDIR). A modify event on a file inside that directory (and inside that mount) should not create a FAN_MODIFY event, because neither of the marks requested to get that event on the file. Fixes: 1968f5ee ("fanotify: use both marks when possible") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
-
Jan Kara authored
commit 44f06ba8 upstream. OSTA UDF specification does not mention whether the CS0 charset in case of two bytes per character encoding should be treated in UTF-16 or UCS-2. The sample code in the standard does not treat UTF-16 surrogates in any special way but on systems such as Windows which work in UTF-16 internally, filenames would be treated as being in UTF-16 effectively. In Linux it is more difficult to handle characters outside of Base Multilingual plane (beyond 0xffff) as NLS framework works with 2-byte characters only. Just make sure we don't leak UTF-16 surrogates into the resulting string when loading names from the filesystem for now. CC: stable@vger.kernel.org # >= v4.6 Reported-by:
Mingye Wang <arthur200126@gmail.com> Signed-off-by:
-
Michael Ellerman authored
commit b8858581 upstream. When we patch an alternate feature section, we have to adjust any relative branches that branch out of the alternate section. But currently we have a bug if we have a branch that points to past the last instruction of the alternate section, eg: FTR_SECTION_ELSE 1: b 2f or 6,6,6 2: ALT_FTR_SECTION_END(...) nop This will result in a relative branch at 1 with a target that equals the end of the alternate section. That branch does not need adjusting when it's moved to the non-else location. Currently we do adjust it, resulting in a branch that goes off into the link-time location of the else section, which is junk. The fix is to not patch branches that have a target == end of the alternate section. Fixes: d20fe50a ("KVM: PPC: Book3S HV: Branch inside feature section") Fixes: 9b1a735d ("powerpc: Add logic to patch alternative feature sections") Cc: stable@vger.kernel.org # v2.6.27+ Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit b32e56e5 upstream. When setting up a CPU, we "push" (activate) a pool VP for it. However it's an error to do so if it already has an active pool VP. This happens when doing soft CPU hotplug on powernv since we don't tear down the CPU on unplug. The HW flags the error which gets captured by the diagnostics. Fix this by making sure to "pull" out any already active pool first. Fixes: 243e2511 ("powerpc/xive: Native exploitation of the XIVE interrupt controller") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Michael Neuling authored
commit 13a83eac upstream. On boot we save the configuration space of PCIe bridges. We do this so when we get an EEH event and everything gets reset that we can restore them. Unfortunately we save this state before we've enabled the MMIO space on the bridges. Hence if we have to reset the bridge when we come back MMIO is not enabled and we end up taking an PE freeze when the driver starts accessing again. This patch forces the memory/MMIO and bus mastering on when restoring bridges on EEH. Ideally we'd do this correctly by saving the configuration space writes later, but that will have to come later in a larger EEH rewrite. For now we have this simple fix. The original bug can be triggered on a boston machine by doing: echo 0x8000000000000000 > /sys/kernel/debug/powerpc/PCI0001/err_injct_outbound On boston, this PHB has a PCIe switch on it. Without this patch, you'll see two EEH events, 1 expected and 1 the failure we are fixing here. The second EEH event causes the anything under the PHB to disappear (i.e. the i40e eth). With this patch, only 1 EEH event occurs and devices properly recover. Fixes: 652defed ("powerpc/eeh: Check PCIe link after reset") Cc: stable@vger.kernel.org # v3.11+ Reported-by:
Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com> Signed-off-by:
Michael Neuling <mikey@neuling.org> Acked-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
-
Matt Redfearn authored
commit c96eebf0 upstream. The label .Llast_fixup\@ is jumped to on page fault within the final byte set loop of memset (on < MIPSR6 architectures). For some reason, in this fault handler, the v1 register is randomly set to a2 & STORMASK. This clobbers v1 for the calling function. This can be observed with the following test code: static int __init __attribute__((optimize("O0"))) test_clear_user(void) { register int t asm("v1"); char *test; int j, k; pr_info("\n\n\nTesting clear_user\n"); test = vmalloc(PAGE_SIZE); for (j = 256; j < 512; j++) { t = 0xa5a5a5a5; if ((k = clear_user(test + PAGE_SIZE - 256, j)) != j - 256) { pr_err("clear_user (%px %d) returned %d\n", test + PAGE_SIZE - 256, j, k); } if (t != 0xa5a5a5a5) { pr_err("v1 was clobbered to 0x%x!\n", t); } } return 0; } late_initcall(test_clear_user); Which demonstrates that v1 is indeed clobbered (MIPS64): Testing clear_user v1 was clobbered to 0x1! v1 was clobbered to 0x2! v1 was clobbered to 0x3! v1 was clobbered to 0x4! v1 was clobbered to 0x5! v1 was clobbered to 0x6! v1 was clobbered to 0x7! Since the number of bytes that could not be set is already contained in a2, the andi placing a value in v1 is not necessary and actively harmful in clobbering v1. Reported-by:
James Hogan <jhogan@kernel.org> Signed-off-by:
Matt Redfearn <matt.redfearn@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/19109/Signed-off-by:
-
Matt Redfearn authored
commit daf70d89 upstream. The __clear_user function is defined to return the number of bytes that could not be cleared. From the underlying memset / bzero implementation this means setting register a2 to that number on return. Currently if a page fault is triggered within the memset_partial block, the value loaded into a2 on return is meaningless. The label .Lpartial_fixup\@ is jumped to on page fault. In order to work out how many bytes failed to copy, the exception handler should find how many bytes left in the partial block (andi a2, STORMASK), add that to the partial block end address (a2), and subtract the faulting address to get the remainder. Currently it incorrectly subtracts the partial block start address (t1), which has additionally been clobbered to generate a jump target in memset_partial. Fix this by adding the block end address instead. This issue was found with the following test code: int j, k; for (j = 0; j < 512; j++) { if ((k = clear_user(NULL, j)) != j) { pr_err("clear_user (NULL %d) returned %d\n", j, k); } } Which now passes on Creator Ci40 (MIPS32) and Cavium Octeon II (MIPS64). Suggested-by:
-
