To check whether the load should take the fast path or not, the code
would check that (r_skb_hlen - load_order) is greater than the offset
of the access using an "Unsigned higher or same" condition. For
halfword accesses and an skb length of 1 at offset 0, that test is
valid, as we end up comparing 0xffffffff(-1) and 0, so the fast path
is taken and the filter allows the load to wrongly succeed. A similar
issue exists for word loads at offset 0 and an skb length of less than
4.

Fix that by using the condition "Signed greater than or equal"
condition for the fast path code for load orders greater than 0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Morton reported following warning on one ARM build
with gcc-4.4 :

net/ipv4/inet_hashtables.c: In function 'inet_ehash_locks_alloc':
net/ipv4/inet_hashtables.c:617: warning: division by zero

Even guarded with a test on sizeof(spinlock_t), compiler does not
like current construct on a !CONFIG_SMP build.

Remove the warning by using a temporary variable.

Fixes: 095dc8e0 ("tcp: fix/cleanup inet_ehash_locks_alloc()")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
ath9k:

* fix device ID check for AR956x

iwlwifi:

* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
  devices (3160).
* revert the new RBD allocation model because it introduced
  a bug when running on weak VM setups.
* new device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit c03abd84 ("net: ethernet: cpsw: don't requests IRQs
we don't use") common isr and napi are separated into separate tx isr
and rx isr/napi, but still in rx napi tx events are handled. So removing
the tx event handling in rx napi.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ip_frag_queue() computes positions, it assumes that the passed
sk_buff does not contain L2 headers.

However, when PACKET_FANOUT_FLAG_DEFRAG is used, IP reassembly
functions can be called on outgoing packets that contain L2 headers.

Also, IPv4 checksum is not corrected after reassembly.

Fixes: 7736d33f ("packet: Add pre-defragmentation support for ipv4 fanouts.")
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the actual code, if a memory allocation error happens while
refilling a Rx descriptor, then the original Rx buffer is both passed
to the networking stack (in a SKB) and let in the Rx ring. This leads
to various kernel oops and crashes.

As a fix, this patch moves Rx descriptor refilling ahead of building
SKB with the associated Rx buffer. In case of a memory allocation
failure, data is dropped and the original DMA buffer is put back into
the Rx ring.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Yoann Sculo <yoann@sculo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 803f8fc4 ("stmmac: move driver data setting into
stmmac_dvr_probe") mistakenly set priv and not priv->dev as
driver data. This meant that the remove, resume and suspend
callbacks that fetched and tried to use this data would most
likely explode. Fix the issue by using the correct variable.

Fixes: 803f8fc4 ("stmmac: move driver data setting into stmmac_dvr_probe")
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Couple of classifier fixes

This fixes a couple of panics in the form of (analogous for
cls_flow{,er}):

[  912.759276] BUG: unable to handle kernel NULL pointer dereference at (null)
[  912.759373] IP: [<ffffffffa09d4d6d>] cls_bpf_change+0x23d/0x268 [cls_bpf]
[  912.759441] PGD 8783c067 PUD 5f684067 PMD 0
[  912.759491] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[  912.759543] Modules linked in: cls_bpf(E) act_gact [...]
[  912.772734] CPU: 3 PID: 10489 Comm: tc Tainted: G        W   E   4.2.0-rc2+ #73
[  912.775004] Hardware name: Apple Inc. MacBookAir5,1/Mac-66F35F19FE2A0D05, BIOS MBA51.88Z.00EF.B02.1211271028 11/27/2012
[  912.777327] task: ffff88025eaa8000 ti: ffff88005f734000 task.ti: ffff88005f734000
[  912.779662] RIP: 0010:[<ffffffffa09d4d6d>]  [<ffffffffa09d4d6d>] cls_bpf_change+0x23d/0x268 [cls_bpf]
[  912.781991] RSP: 0018:ffff88005f7379c8  EFLAGS: 00010286
[  912.784183] RAX: ffff880201d64e48 RBX: 0000000000000000 RCX: ffff880201d64e40
[  912.786402] RDX: 0000000000000000 RSI: ffffffffa09d51c0 RDI: ffffffffa09d51a6
[  912.788625] RBP: ffff88005f737a68 R08: 0000000000000000 R09: 0000000000000000
[  912.790854] R10: 0000000000000001 R11: 0000000000000001 R12: ffff880078ab5a80
[  912.793082] R13: ffff880232b31570 R14: ffff88005f737ae0 R15: ffff8801e215d1d0
[  912.795181] FS:  00007f3c0c80d740(0000) GS:ffff880265400000(0000) knlGS:0000000000000000
[  912.797281] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  912.799402] CR2: 0000000000000000 CR3: 000000005460f000 CR4: 00000000001407e0
[  912.799403] Stack:
[  912.799407]  ffffffff00000000 ffff88023ea18000 000000005f737a08 0000000000000000
[  912.799415]  ffffffff81f06140 ffff880201d64e40 0000000000000000 ffff88023ea1804c
[  912.799418]  0000000000000000 ffff88023ea18044 ffff88023ea18030 ffff88023ea18038
[  912.799418] Call Trace:
[  912.799437]  [<ffffffff816d5685>] tc_ctl_tfilter+0x335/0x910
[  912.799443]  [<ffffffff813622a8>] ? security_capable+0x48/0x60
[  912.799448]  [<ffffffff816b90e5>] rtnetlink_rcv_msg+0x95/0x240
[  912.799454]  [<ffffffff810f612d>] ? trace_hardirqs_on+0xd/0x10
[  912.799456]  [<ffffffff816b902f>] ? rtnetlink_rcv+0x1f/0x40
[  912.799459]  [<ffffffff816b902f>] ? rtnetlink_rcv+0x1f/0x40
[  912.799461]  [<ffffffff816b9050>] ? rtnetlink_rcv+0x40/0x40
[  912.799464]  [<ffffffff816df38f>] netlink_rcv_skb+0xaf/0xc0
[  912.799467]  [<ffffffff816b903e>] rtnetlink_rcv+0x2e/0x40
[  912.799469]  [<ffffffff816deaef>] netlink_unicast+0xef/0x1b0
[  912.799471]  [<ffffffff816defa0>] netlink_sendmsg+0x3f0/0x620
[  912.799476]  [<ffffffff81687028>] sock_sendmsg+0x38/0x50
[  912.799479]  [<ffffffff81687938>] ___sys_sendmsg+0x288/0x290
[  912.799482]  [<ffffffff810f7852>] ? __lock_acquire+0x572/0x2050
[  912.799488]  [<ffffffff810265db>] ? native_sched_clock+0x2b/0x90
[  912.799493]  [<ffffffff8116135f>] ? __audit_syscall_entry+0xaf/0x100
[  912.799497]  [<ffffffff8116135f>] ? __audit_syscall_entry+0xaf/0x100
[  912.799501]  [<ffffffff8112aa19>] ? current_kernel_time+0x69/0xd0
[  912.799505]  [<ffffffff81266f16>] ? __fget_light+0x66/0x90
[  912.799508]  [<ffffffff81688812>] __sys_sendmsg+0x42/0x80
[  912.799510]  [<ffffffff81688862>] SyS_sendmsg+0x12/0x20
[  912.799515]  [<ffffffff817f9a6e>] entry_SYSCALL_64_fastpath+0x12/0x76
[  912.799540] Code: 4d 88 49 8b 57 08 48 89 51 08 49 8b 57 10 48 89 c8 48 83 c0 08 48
                     89 51 10 48 8b 51 10 48 c7 c6 c0 51 9d a0 48 c7 c7 a6 51 9d a0 <48>
                     89 02 48 8b 51 08 48 89 42 08 48 b8 00 02 20 00 00 00 ad de
[  912.799544] RIP  [<ffffffffa09d4d6d>] cls_bpf_change+0x23d/0x268 [cls_bpf]
[  912.799544]  RSP <ffff88005f7379c8>
[  912.799545] CR2: 0000000000000000
[  912.807380] ---[ end trace a6440067cfdc7c29 ]---

I've split them into 3 patches, so they can be backported easier
when needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The following test case causes a NULL pointer dereference in cls_flow:

  tc filter add dev foo parent 1: handle 0x1 flow hash keys dst action ok
  tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
            flow hash keys mark action drop

To be more precise, actually two different panics are fixed, the first
occurs because tcf_exts_init() is not called on the newly allocated
filter when we do a replace. And the second panic uncovered after that
happens since the arguments of list_replace_rcu() are swapped, the old
element needs to be the first argument and the new element the second.

Fixes: 70da9f0b ("net: sched: cls_flow use RCU")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following test case causes a NULL pointer dereference in cls_flower:

  tc filter add dev foo parent 1: flower eth_type ipv4 action ok flowid 1:1
  tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
            flower eth_type ipv6 action ok flowid 1:1

The problem is that commit 77b9900e ("tc: introduce Flower classifier")
accidentally swapped the arguments of list_replace_rcu(), the old
element needs to be the first argument and the new element the second.

Fixes: 77b9900e ("tc: introduce Flower classifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following test case causes a NULL pointer dereference in cls_bpf:

  FOO="1,6 0 0 4294967295,"
  tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
  tc filter replace dev foo parent 1: pref 49152 handle 0x1 \
            bpf bytecode "$FOO" flowid 1:1 action drop

The problem is that commit 1f947bf1 ("net: sched: rcu'ify cls_bpf")
accidentally swapped the arguments of list_replace_rcu(), the old
element needs to be the first argument and the new element the second.

Fixes: 1f947bf1 ("net: sched: rcu'ify cls_bpf")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Some fixes for the current cycle:

 1. Arik introduced an rtnl-locked regulatory API to be able
    to differentiate between place do/don't have the RTNL;
    this fixes missing locking in some of the code paths

 2. Two small mesh bugfixes from Bob, one to avoid treating
    a certain malformed over-the-air frame and one to avoid
    sending a garbage field over the air.

 3. A fix for powersave during WoWLAN suspend from Krishna Chaitanya.

 4. A fix for a powersave vs. aggregation teardown race, from Michal.

 5. Thomas reduced the loglevel of CRDA messages to avoid spamming
    the kernel log with mostly irrelevant information.

 6. Tom fixed a dangling debugfs directory pointer that could cause
    crashes if subsequent addition of the same interface to debugfs
    failed for some reason.

 7. A fix from myself for a list corruption issue in mac80211 during
    combined interface shutdown/removal - shut down interfaces first
    and only then remove them to avoid that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We store c45 PHY's id information in c45_ids, so it should be used to
check the matching between PHY driver and PHY device for c45 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel generates a lot of warnings when dst entry reference counter
overflows and becomes negative. That bug was seen several times at
machines with outdated 3.10.y kernels. Most like it's already fixed
in upstream. Anyway that flood completely kills machine and makes
further debugging impossible.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) If sk_filter() is applied, skb was leaked (not freed)
2) Testing SOCK_DEAD twice is racy :
   packet could be freed while already queued.
3) Remove obsolete comment about caching skb->len
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.

Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:

1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
   bond0 has the same mac address with eth0, it is MAC1.

2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
   eth1 is backup, eth1 has MAC2.

3) ifconfig eth0 down
   eth1 became active slave, bond will swap MAC for eth0 and eth1,
   so eth1 has MAC1, and eth0 has MAC2.

4) ifconfig eth1 down
   there is no active slave, and eth1 still has MAC1, eth2 has MAC2.

5) ifconfig eth0 up
   the eth0 became active slave again, the bond set eth0 to MAC1.

Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.

This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.2-20150716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-07-16

this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reverts 19424e05 ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).

For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.

Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).

We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
 Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
    link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)

 After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[  908.963051] eql: event: 9
[  908.963052] eql: IFF_SLAVE
[  908.963054] eql: event: 2
[  908.963056] eql: IFF_SLAVE
[  908.963058] eql: event: 6
[  908.963059] eql: IFF_SLAVE
[  908.963110] bond0: Releasing active interface eql
[  908.976168] bond0: Destroying bond bond0
[  908.976266] bond0 (unregistering): Released all slaves
[  908.984097] ------------[ cut here ]------------
[  908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[  908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[  908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]

[  908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G        W  O
4.2.0-rc2+ #8
[  908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  908.984172]  0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[  908.984175]  ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[  908.984178]  ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[  908.984181] Call Trace:
[  908.984188]  [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[  908.984193]  [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[  908.984196]  [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[  908.984199]  [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[  908.984205]  [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[  908.984208]  [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[  908.984217]  [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[  908.984225]  [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[  908.984228]  [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[  908.984232]  [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[  908.984236]  [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[  908.984241]  [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[  908.984244]  [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[  908.984247] ---[ end trace 7c006ed4abbef24b ]---

Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f9399814 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3 ("bonding: Manage /proc/net/bonding/ entries from
                      the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.

This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.

Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).

Indeed, br0 uses FID 0, and br1 uses FID 3.

After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).

With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RTNL is required to check for IR-relaxation conditions that allow
more channels to beacon. Export an RTNL locked version of reg_can_beacon
and use it where possible in AP/STA interface type flows, where
IR-relaxation may be applicable.

Fixes: 06f207fc ("cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Although mesh_rx_plink_frame() already checks that frames have enough
bytes for the action code plus another two bytes for capability/reason
code, it doesn't take into account that confirm frames also have an
additional two-byte aid.  As a result, a corrupt frame could cause a
subsequent subtraction to wrap around to ill effect.  Add another
check for this case.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

According to 802.11-2012 8.5.16.3.2 AID comes directly after the
capability bytes in mesh peering confirm frames.  The existing
code, however, was adding a 2 byte offset to this location,
resulting in garbage data going out over the air.  Remove the
offset to fix it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With a basic Linux userspace, the messages "Calling CRDA to update
world regulatory domain" appears 10 times after boot every second or
so, followed by a final "Exceeded CRDA call max attempts. Not calling
CRDA". For those of us not having the corresponding userspace parts,
having those messages repeatedly displayed at boot time is a bit
annoying, so this commit reduces their log level to pr_debug().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the hardware is unregistered while interfaces are up, mac80211 will
unregister all interfaces, which in turns causes mac80211 to be called
again to remove them all from the driver and eventually shut down the
hardware.

During this shutdown, however, it's currently already unsafe to iterate
the list of interfaces atomically, as the list is manipulated in an
unsafe manner. This puts an undue burden on the driver - it must stop
all its activities before calling ieee80211_unregister_hw(), while in
the normal stop path it can do all cleanup in the stop method. If, for
example, it's using the iteration during RX for some reason, it would
have to stop RX before unregistering to avoid crashes.

Fix this problem by closing all interfaces before unregistering them.
This will cause the driver stop to have completed before we manipulate
the interface list, and after the driver is stopped *and* has called
ieee80211_unregister_hw() it really musn't be iterating any more as
the memory will be freed as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If for any reason we're in the middle of PS-polling or awake after
TX due to dynamic powersave while going to suspend, go back to save
power. This might cause a response frame to get lost, but since we
can't really wait for it while going to suspend that's still better
than not enabling powersave which would cause higher power usage
during (and possibly even after) suspend.

Note that this really only affects the very few drivers that use
the powersave implementation in mac80211.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
[rewrite misleading commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When acting as AP and a PS-Poll frame is received
associated station is marked as one in a Service
Period. This state is kept until Tx status for
released frame is reported. While a station is in
Service Period PS-Poll frames are ignored.

However if PS-Poll was received during A-MPDU
teardown it was possible to have the to-be
released frame re-queued back to pending queue.
In such case the frame was stripped of 2 important
flags:

 (a) IEEE80211_TX_CTL_NO_PS_BUFFER
 (b) IEEE80211_TX_STATUS_EOSP

Stripping of (a) led to the frame that was to be
released to be queued back to ps_tx_buf queue. If
station remained to use only PS-Poll frames the
re-queued frame (and new ones) was never actually
transmitted because mac80211 would ignore
subsequent PS-Poll frames due to station being in
Service Period. There was nothing left to clear
the Service Period bit (no xmit -> no tx status ->
no SP end), i.e. the AP would have the station
stuck in Service Period. Beacon TIM would
repeatedly prompt station to poll for frames but
it would get none.

Once (a) is not stripped (b) becomes important
because it's the main condition to clear the
Service Period bit of the station when Tx status
for the released frame is reported back.

This problem was observed with ath9k acting as P2P
GO in some testing scenarios but isn't limited to
it. AP operation with mac80211 based Tx A-MPDU
control combined with clients using PS-Poll frames
is subject to this race.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If we don't do this, and we then fail to recreate the debugfs
directory during a mode change, then we will fail later trying
to add stations to this now bogus directory:

BUG: unable to handle kernel NULL pointer dereference at 0000006c
IP: [<c0a92202>] mutex_lock+0x12/0x30
Call Trace:
[<c0678ab4>] start_creating+0x44/0xc0
[<c0679203>] debugfs_create_dir+0x13/0xf0
[<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211]

Cc: stable@kernel.org
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'iwlwifi-for-kalle-2015-06-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
        devices (3160).
* revert the new RBD allocation model because it introduced
	a bug when running on weak VM setups.
* a new device IDs

First, dma_sync_single_for_cpu() shouldn't have been called in the first place
(it's a streaming DMA API), dma_unmap_single() should have been called instead.
Second, dma_unmap_single() call after handing the buffer to napi_gro_receive()
makes little sense.  Moreover desc->dptr might not be valid at this point.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The regulators power and transceiver are optional. If those are not
present, the pointer (or error pointer) is correctly handled by the
driver, hence we can use devm_regulator_get_optional safely, which
avoids regulators getting created.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If a valid power regulator or a dummy regulator is used (which
happens to be the case when no regulator is specified), restart_work
is queued no matter whether the device was running or not at suspend
time. Since work queues get initialized in the ndo_open callback,
resuming leads to a NULL pointer exception.

Reverse exactly the steps executed at suspend time:
- Enable the power regulator in any case
- Enable the transceiver regulator if the device was running, even in
  case we have a power regulator
- Queue restart_work only in case the device was running

Fixes: bf66f373 ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Johan Hedberg says:

====================
pull request: bluetooth 2015-07-15

Here's a regression fix for Broadcom Bluetooth adapters found at least
in certain Apple laptops. The issue was introduced in 4.1 so there's the
appropriate "Cc: stable" entry for it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

prog->bpf_ops is populated when act_bpf is used with classic BPF and
prog->bpf_name is optionally used with extended BPF.
Fix memory leak when act_bpf is released.

Fixes: d23b8ad8 ("tc: add BPF based action")
Fixes: a8cb5f55 ("act_bpf: add initial eBPF support for actions")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>