- 12 Sep, 2024 3 commits
-
-
Luiz Augusto von Dentz authored
Requesting transfers of the exact same size of wMaxPacketSize may result in ZPL/short-transfer since the USB stack cannot handle it as we are limiting the buffer size to be the same as wMaxPacketSize. Also, in terms of throughput this change has the same effect to interrupt endpoint as 290ba200 "Bluetooth: Improve USB driver throughput by increasing the frame size" had for the bulk endpoint, so users of the advertisement bearer (e.g. BT Mesh) may benefit from this change. Fixes: 5e23b923 ("[Bluetooth] Add generic driver for Bluetooth USB devices") Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by:
Kiran K <kiran.k@intel.com>
-
Michael Burch authored
Add 2 USB HW IDs for MT7925 (0xe118/e) to ensure proper recognition. These HW IDs are extracted from Windows driver inf file: https://dlcdnets.asus.com/pub/ASUS/nb/Image/Driver/Bluetooth/39389/Bluetooth_DCH_MediaTek_B_V1.1037.0.433Sub2_39389.exe?model=H7606WV Patch has been tested successfully on an Asus ProArt P16 model H7606WV. Controller is recognized devices pair successfully. Signed-off-by:
Michael Burch <me@michaelburch.net> Signed-off-by:
-
Scott Ehlert authored
CYW4373 devices soldered onto the PCB (non-removable), use a UART connection for Bluetooth and the advertised btsdio support as an SDIO function should be ignored. Signed-off-by:
Scott Ehlert <ehlert@battelle.org> Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
-
- 10 Sep, 2024 37 commits
-
-
Luiz Augusto von Dentz authored
This ignores errors from HCI_OP_REMOTE_NAME_REQ_CANCEL since it shouldn't interfere with the stopping of discovery and in certain conditions it seems to be failing. Link: https://github.com/bluez/bluez/issues/575 Fixes: d0b13706 ("Bluetooth: hci_sync: Rework init stages") Signed-off-by:
-
Luiz Augusto von Dentz authored
This marks BT_CMTP as DEPRECATED in preparation to get it removed. Signed-off-by: -
Justin Stitt authored
strncpy() is deprecated for use on NUL-terminated destination strings [0] and as such we should prefer more robust and less ambiguous string interfaces. The CAPI (part II) [1] states that the manufacturer id should be a "zero-terminated ASCII string" and should "always [be] zero-terminated." Much the same for the serial number: "The serial number, a seven-digit number coded as a zero-terminated ASCII string". Along with this, its clear the original author intended for these buffers to be NUL-padded as well. To meet the specification as well as properly NUL-pad, use strscpy_pad(). In doing this, an opportunity to simplify this code is also present. Remove the min_t() and combine the length check into the main if. Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [0] Link: https://capi.org/downloads.html [1] Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html Link: https://github.com/KSPP/linux/issues/90 Cc: linux-hardening@vger.kernel.org Signed-off-by:
Justin Stitt <justinstitt@google.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
If HCI_CONN_MGMT_CONNECTED has been set then the event shall be HCI_CONN_MGMT_DISCONNECTED. Fixes: b644ba33 ("Bluetooth: Update device_connected and device_found events to latest API") Signed-off-by:
-
Hilda Wu authored
For tracking multiple devices concurrently with a condition. The patch enables the HCI_QUIRK_USE_MSFT_EXT_ADDRESS_FILTER quirk on RTL8852B controller. The quirk setting is based on commit 9e14606d ("Bluetooth: msft: Extended monitor tracking by address filter") With this setting, when a pattern monitor detects a device, this feature issues an address monitor for tracking that device. Let the original pattern monitor keep monitor new devices. Signed-off-by:
Hilda Wu <hildawu@realtek.com> Signed-off-by:
-
Hans de Goede authored
A LED trigger's activate() callback gets called when the LED trigger gets activated for a specific LED, so that the trigger code can ensure the LED state matches the current state of the trigger condition (LED_FULL when HCI_UP is set in this case). led_trigger_event() is intended for trigger condition state changes and iterates over _all_ LEDs which are controlled by this trigger changing the brightness of each of them. In the activate() case only the brightness of the LED which is being activated needs to change and that LED is passed as an argument to activate(), switch to led_set_brightness() to only change the brightness of the LED being activated. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Li Zetao authored
Use kvmemdup instead of kvmalloc() + memcpy() to simplify the code. No functional change intended. Signed-off-by:
Li Zetao <lizetao1@huawei.com> Signed-off-by:
-
Pavel Nikulin authored
Add the support ID (0x13d3, 0x3608) to usb_device_id table for Realtek MT7925B14L found on AW-EM637 WiFi+BT modules in 2024 Asus laptops. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by:
Pavel Nikulin <pavel@noa-labs.com> Signed-off-by:
-
Max Chou authored
Add the support for RTL8922A BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=8922 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C885A01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by:
Max Chou <max.chou@realtek.com> Signed-off-by:
-
Frédéric Danis authored
Starting a BCM UART controller not defined as a platform device or a serdev with "btattach -B /dev/ttyS1 -P bcm -S 3000000" works fine but the serial port remains at the init_speed, i.e. 115200. The oper_speed is only set if a device is declared in ACPI, device tree or as a platform device. This commit copies the serial port speed fixed by hciattach to the oper_speed on line discipline opening. Signed-off-by:
Frédéric Danis <frederic.danis@collabora.com> Signed-off-by:
-
Kuan-Wei Chiu authored
Since kzalloc already zeroes the allocated memory, the subsequent memset call is unnecessary. This patch removes the redundant memset to clean up the code and enhance efficiency. Signed-off-by:
Kuan-Wei Chiu <visitorckw@gmail.com> Signed-off-by:
-
Yue Haibing authored
Commit e7b02296 ("Bluetooth: Remove BT_HS") removed the implementations but leave declarations. Signed-off-by:
Yue Haibing <yuehaibing@huawei.com> Signed-off-by:
-
Bartosz Golaszewski authored
Describe the inputs from the PMU that the Bluetooth module on wcn6855 consumes and drop the ones from the host. This breaks the current contract but the only two users of wcn6855 upstream - sc8280xp based boards - will be updated in DTS patches sent separately while the hci_qca driver will remain backwards compatible with older DT sources. Acked-by:
Rob Herring (Arm) <robh@kernel.org> Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by:
-
Neeraj Sanjay Kale authored
This enables btnxpuart driver to handle ISO RX packet when DUT is configured as audio sink. Tested IW612 on iMX8MMini platform and BlueZ-5.77 as follows: 1) Configured DUT with bap_bcast_sink role in pipewire configuration file. 2) Started pipewire and DUT is able to sync with Broadcast source through pipewire. 3) ISO data RX is seen in btmon. 4) Audio/Music is heard on audio jack. Signed-off-by:
Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by:
Sarveshwar Bajaj <sarveshwar.bajaj@nxp.com> Signed-off-by:
-
Neeraj Sanjay Kale authored
This adds ISO packet support in h4_recv.h, which was created before ISO packet handling was added to hci_h4.c and hci_uart.c Signed-off-by:
-
Hilda Wu authored
Add the support ID (0x0489, 0xe122) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e122 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Luiz Augusto von Dentz authored
This inverts the LE State flag so by default we assume the controllers would report valid states rather than invalid so it is inline with the respective quirk (HCI_QUIRK_BROKEN_LE_STATES). Signed-off-by: -
Yang Li authored
Add Amlogic Bluetooth entry to MAINTAINERS to clarify the maintainers Signed-off-by:
Yang Li <yang.li@amlogic.com> Signed-off-by:
-
Yang Li authored
Add a new HCI protocol HCI_UART_AML for the Amlogic Bluetooth controller. It works on the standard H4 protocol via a 4-wire UART interface, with baud rates up to 4 Mbps. The controller supports two types of commands: the TCI commands and the vendor command. The former is for initial setup including setting baud rates, downloading fw, starting chip and etc, while the latter is for dumping firmware versions and setting public address after firmware updates and normal startup. It was verified on board of T602 (S905X4 + W265S2). dmesg: .. [ 5.313450] Bluetooth: HCI UART protocol AML registered [ 6.506052] Bluetooth: hci0: fw_version: date = 42.28, number = 0xb2fd ... Co-developed-by:
Ye He <ye.he@amlogic.com> Signed-off-by:
-
Yang Li authored
Add binding document for Amlogic Bluetooth chipsets attached over UART. Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Alexander Hall authored
This patch fixes bluetooth support on the MediaTek MT7925 WiFi 7 + BT 5.3 M.2 chipset that I purchased from aliexpress (and which arrived today). The PCB states that it is an MT7925B22M. Device from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3604 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us High fidelity images I took of the chip itself for future reference: https://archive.org/details/MediaTek-MT7925B22M/ Webpage the chip was purchased from, note it is different from the images taken: https://web.archive.org/web/20240620021119/https://www.aliexpress. us/item/3256806821207897.html Signed-off-by:
Alexander Hall <bearodark@gmail.com> Signed-off-by:
-
Kiran authored
Add support for handling ISO RX and TX packets. Signed-off-by:
-
Kiran K authored
Add a helper function hci_iso_hdr() to extract iso header from skb. Signed-off-by:
-
Alexander Dahl authored
Was slightly misleading before, because printed is pointer to fwnode, not to phy device, as placement in message suggested. Include header for dev_dbg() declaration while at it. Output before: [ +0.001247] mdio_bus f802c000.ethernet-ffffffff: registered phy 2612f00a fwnode at address 3 Output after: [ +0.001229] mdio_bus f802c000.ethernet-ffffffff: registered phy fwnode /ahb/apb/ethernet@f802c000/ethernet-phy@3 at address 3 Reviewed-by:Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Alexander Dahl <ada@thorsis.com> Link: https://patch.msgid.link/20240906062256.11289-1-ada@thorsis.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
D. Wythe authored
In commit 48b6190a ("net/smc: Limit SMC visits when handshake workqueue congested"), we introduce a mechanism to put constraint on SMC connections visit according to the pressure of SMC handshake process. At that time, we believed that controlling the feature through netlink was sufficient. However, most people have realized now that netlink is not convenient in container scenarios, and sysctl is a more suitable approach. In addition, since commit 462791bb ("net/smc: add sysctl interface for SMC") had introcuded smc_sysctl_net_init(), it is reasonable for us to initialize limit_smc_hs in it instead of initializing it in smc_pnet_net_int(). Signed-off-by:
D. Wythe <alibuda@linux.alibaba.com> Reviewed-by:
Wen Gu <guwen@linux.alibaba.com> Reviewed-by:
Jan Karcher <jaka@linux.ibm.com> Link: https://patch.msgid.link/1725590135-5631-1-git-send-email-alibuda@linux.alibaba.comSigned-off-by:
-
Lee Trager authored
This adds support to show firmware version information for both stored and running firmware versions. The version and commit is displayed separately to aid monitoring tools which only care about the version. Example output: # devlink dev info pci/0000:01:00.0: driver fbnic serial_number 88-25-08-ff-ff-01-50-92 versions: running: fw 24.07.15-017 fw.commit h999784ae9df0 fw.bootloader 24.07.10-000 fw.bootloader.commit hfef3ac835ce7 stored: fw 24.07.24-002 fw.commit hc9d14a68b3f2 fw.bootloader 24.07.22-000 fw.bootloader.commit h922f8493eb96 fw.undi 01.00.03-000 Signed-off-by:Lee Trager <lee@trager.us> Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Link: https://patch.msgid.link/20240905233820.1713043-1-lee@trager.usSigned-off-by:
-
Paolo Abeni authored
Daniel Machon says: ==================== net: lan966x: use the newly introduced FDMA library This patch series is the second of a 2-part series [1], that adds a new common FDMA library for Microchip switch chips Sparx5 and lan966x. These chips share the same FDMA engine, and as such will benefit from a common library with a common implementation. This also has the benefit of removing a lot of open-coded bookkeeping and duplicate code for the two drivers. In this second series, the FDMA library will be taken into use by the lan966x switch driver. ################### # Example of use: # ################### - Initialize the rx and tx fdma structs with values for: number of DCB's, number of DB's, channel ID, DB size (data buffer size), and total size of the requested memory. Also provide two callbacks: nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr. - Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent(). - Initialize the DCB's with fdma_dcb_init(). - Add new DCB's with fdma_dcb_add(). - Free memory with fdma_free_phys() or fdma_free_coherent(). ##################### # Patch breakdown: # ##################### Patch #1: select FDMA library for lan966x. Patch #2: includes the fdma_api.h header and removes old symbols. Patch #3: replaces old rx and tx variables with equivalent ones from the fdma struct. Only the variables that can be changed without breaking traffic is changed in this patch. Patch #4: uses the library for allocation of rx buffers. This requires quite a bit of refactoring in this single patch. Patch #5: uses the library for adding DCB's in the rx path. Patch #6: uses the library for freeing rx buffers. Patch #7: uses the library for allocation of tx buffers. This requires quite a bit of refactoring in this single patch. Patch #8: uses the library for adding DCB's in the tx path. Patch #9: uses the library helpers in the tx path. Patch #10: ditch last_in_use variable and use library instead. Patch #11: uses library helpers throughout. Patch #12: refactor lan966x_fdma_reload() function. [1] https://lore.kernel.org/netdev/20240902-fdma-sparx5-v1-0-1e7d5e5a9f34@microchip.com/Signed-off-by:Daniel Machon <daniel.machon@microchip.com> ==================== Link: https://patch.msgid.link/20240905-fdma-lan966x-v1-0-e083f8620165@microchip.comSigned-off-by:
-
Daniel Machon authored
Now that we store everything in the fdma structs, refactor lan966x_fdma_reload() to store and restore the entire struct. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Daniel Machon authored
The library provides helpers for a number of DCB and DB operations. Use these throughout the code and remove the old ones. Signed-off-by:
-
Daniel Machon authored
This variable is used in the tx path to determine the last used DCB. The library has the variable last_dcb for the exact same purpose. Ditch the last_in_use variable throughout. Signed-off-by:
-
Daniel Machon authored
The library has the helper fdma_free_phys() for freeing physical FDMA memory. Use it in the exit path. Signed-off-by:
-
Daniel Machon authored
Use the fdma_dcb_add() function to add DCB's in the tx path. This gets rid of the open-coding of nextptr and dataptr handling and leaves it to the library. Signed-off-by:
-
Daniel Machon authored
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for rx buffer allocation and use the new buffers throughout. In order to replace the old buffers with the new ones, we have to do the following refactoring: - use fdma_alloc_phys() and fdma_dcb_init() - replace the variables: tx->dma, tx->dcbs and tx->curr_entry with the equivalents from the FDMA struct. - add lan966x_fdma_tx_dataptr_cb callback for obtaining the dataptr. - Initialize FDMA struct values. Signed-off-by: -
Daniel Machon authored
The library has the helper fdma_free_phys() for freeing physical FDMA memory. Use it in the exit path. Signed-off-by:
-
Daniel Machon authored
Use the fdma_dcb_add() function to add DCB's in the rx path. This gets rid of the open-coding of nextptr and dataptr handling and the functions for adding DCB's. Signed-off-by:
-
Daniel Machon authored
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for rx buffer allocation and use the new buffers throughout. In order to replace the old buffers with the new ones, we have to do the following refactoring: - use fdma_alloc_phys() and fdma_dcb_init() - replace the variables: rx->dma, rx->dcbs and rx->last_entry with the equivalents from the FDMA struct. - make use of fdma->db_size for rx buffer size. - add lan966x_fdma_rx_dataptr_cb callback for obtaining the dataptr. - Initialize FDMA struct values. Signed-off-by: -
Daniel Machon authored
Replace the old rx and tx variables: channel_id, FDMA_DCB_MAX, FDMA_RX_DCB_MAX_DBS, FDMA_TX_DCB_MAX_DBS, dcb_index and db_index with the equivalents from the FDMA rx and tx structs. These variables are not entangled in any buffer allocation and can therefore be replaced in advance. Signed-off-by:
-
