- 23 Nov, 2022 40 commits
-
-
Rasmus Villemoes authored
Silence the run-time warning SPI driver ad74413r has no spi_device_id for adi,ad74412r Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Link: https://lore.kernel.org/r/20221115095517.1008632-2-linux@rasmusvillemoes.dkSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Luca Weiss authored
As in other bindings, let's use specific compatibles together with the fallback compatible. Adjust the bindings for it. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20221031182456.952648-1-luca@z3ntu.xyzSigned-off-by:
-
Lorenzo Bianconi authored
Add device bindings for lsm6dso16is IMU sensor. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Acked-by:
-
Lorenzo Bianconi authored
Add support to STM LSM6DSO16IS (accelerometer and gyroscope) Mems sensor. Datasheet: https://www.st.com/resource/en/datasheet/lsm6dso16is.pdfTested-by:
Mario Tesi <mario.tesi@st.com> Signed-off-by:
-
Cosmin Tanislav authored
The AD74115H is a single-channel, software-configurable, input and output device for industrial control applications. The AD74115H provides a wide range of use cases, integrated on a single chip. These use cases include analog output, analog input, digital output, digital input, resistance temperature detector (RTD), and thermocouple measurement capability. The AD74115H also has an integrated HART modem. A serial peripheral interface (SPI) is used to handle all communications to the device, including communications with the HART modem. The digital input and digital outputs can be accessed via the SPI or the general-purpose input and output (GPIO) pins to support higher speed data rates. The device features a 16-bit, sigma-delta analog-to-digital converter (ADC) and a 14-bit digital-to-analog converter (DAC). The AD74115H contains a high accuracy 2.5 V on-chip reference that can be used as the DAC and ADC reference. Signed-off-by:
Cosmin Tanislav <cosmin.tanislav@analog.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20221117080916.411766-3-cosmin.tanislav@analog.comSigned-off-by:
-
Cosmin Tanislav authored
The AD74115H is a single-channel, software-configurable, input and output device for industrial control applications. The AD74115H provides a wide range of use cases, integrated on a single chip. These use cases include analog output, analog input, digital output, digital input, resistance temperature detector (RTD), and thermocouple measurement capability. The AD74115H also has an integrated HART modem. A serial peripheral interface (SPI) is used to handle all communications to the device, including communications with the HART modem. The digital input and digital outputs can be accessed via the SPI or the general-purpose input and output (GPIO) pins to support higher speed data rates. The device features a 16-bit, sigma-delta analog-to-digital converter (ADC) and a 14-bit digital-to-analog converter (DAC). The AD74115H contains a high accuracy 2.5 V on-chip reference that can be used as the DAC and ADC reference. Signed-off-by:
-
Rasmus Villemoes authored
The constant AD74413R_ADC_RESULT_MAX is defined via GENMASK, so its type is "unsigned long". Hence in the expression voltage_offset * AD74413R_ADC_RESULT_MAX, voltage_offset is first promoted to unsigned long, and since it may be negative, that results in a garbage value. For example, when range is AD74413R_ADC_RANGE_5V_BI_DIR, voltage_offset is -2500 and voltage_range is 5000, so the RHS of this assignment is, depending on sizeof(long), either 826225UL or 3689348814709142UL, which after truncation to int then results in either 826225 or 1972216214 being the output from in_currentX_offset. Casting to int avoids that promotion and results in the correct -32767 output. Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20221118123209.1658420-1-linux@rasmusvillemoes.dk Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Minghao Chi authored
Convert platform_get_resource(), devm_ioremap_resource() to a single call to devm_platform_get_and_ioremap_resource(), as this is exactly what this function does. Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
ye xingchen <ye.xingchen@zte.com.cn> Reviewed-by:
-
Ramona Bolboaca authored
Remove adis_initial_startup function since it is not used anymore. Signed-off-by:
Ramona Bolboaca <ramona.bolboaca@analog.com> Reviewed-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16240_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16203_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16400_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16260_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16136_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16209_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16201_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Add '__adis_enable_irq()' implementation which is the unlocked version of 'adis_enable_irq()'. Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from '__adis_intial_startup()' to keep the expected unlocked functionality. This fix is needed to remove a deadlock for all devices which are using 'adis_initial_startup()'. The deadlock occurs because the same mutex is acquired twice, without releasing it. The mutex is acquired once inside 'adis_initial_startup()', before calling '__adis_initial_startup()', and once inside 'adis_enable_irq()', which is called by '__adis_initial_startup()'. The deadlock is removed by calling '__adis_enable_irq()', instead of 'adis_enable_irq()' from within '__adis_initial_startup()'. Fixes: b600bd7e ("iio: adis: do not disabe IRQs in 'adis_init()'") Signed-off-by:
-
Ibrahim Tilki authored
VREFP bit was missing from channel configuration mask and VREFN bit was included twice instead which fails to enable positive reference buffer when requested by a channel. Channels that don't enable vrefp buffer were not affected. Fixes: a44ef7c4 ("iio: adc: add max11410 adc driver") Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Ibrahim Tilki <Ibrahim.Tilki@analog.com> Link: https://lore.kernel.org/r/20221122114718.17557-1-Ibrahim.Tilki@analog.comSigned-off-by:
-
Edmund Berenson authored
- The ad7927 is fully compatible with ad7928 driver, add documentation for device. - ad7923 and ad7924 are treated the same in the driver, show the relationship in the documentation. Suggested-by:
Lukasz Zemla <Lukasz.Zemla@woodward.com> Signed-off-by:
Edmund Berenson <edmund.berenson@emlix.com> Reviewed-by:
-
Rajat Khandelwal authored
Maxim MAX30208 is a digital temperature sensor with 0.1°C accuracy. Add support for max30208 driver in iio subsystem. Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX30208.pdfSigned-off-by:
Rajat Khandelwal <rajat.khandelwal@linux.intel.com> Link: https://lore.kernel.org/r/20221122175300.800956-1-rajat.khandelwal@linux.intel.comSigned-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20221118224540.619276-569-uwe@kleine-koenig.orgSigned-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221118224540.619276-191-uwe@kleine-koenig.orgSigned-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Crt Mori <cmo@melexis.com> Reviewed-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
