This patch sets the led_classdev max_brightness to the maximum level
value supported by hardware. This allows to get rid of the brightness
conversion operation (from software [0:LED_FULL] to hardware ranges) in
brightness_set().
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This patch converts the leds-netxbig driver to use the devres functions
devm_gpio_request_one() and devm_led_classdev_register(). This allows to
simplify the code a bit.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Since DT support is now available for the LEDs found on the LaCie
netxbig boards (Kirkwood-based), then the old-fashion netxbig board
setup file is no longer needed. This patch removes this file.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This patch adds DT entries for the LEDs found on the Kirkwood-based
LaCie boards 2Big and 5Big Network v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This patch adds device tree support for the netxbig LEDs.

This also introduces a additionnal DT binding for the GPIO extension bus
(netxbig-gpio-ext) used to configure the LEDs. Since this bus could also
be used to control other devices, then it seems more suitable to have it
in a separate DT binding.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This patch adds possibility to invert heartbeat blinking.
The inverted LED is more time ON then OFF. It's because it looks
better when the heartbeat LED is next to other LED which is most
time ON. The invert value is exported same way via sysfs in file
invert like oneshot. I get inspiration from this trigger.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Since the API for controlling LED brightness and blinking is defined in
the LED core, move the related timer and work callbacks to the led-core.c,
and initialize them through a new led_core_init API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>

Fixes the following randconfig problem

leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister'
leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Spaces at the starting of a line are removed, indentation using
tab, instead of space. Also, line width of more than 80 characters
is also taken care of.
Two warnings are left alone to aid better readability.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Use of resource-managed function devm_led_classdev_register
instead of led_classdev_register is preferred, consequently
remove redundant function micro_leds_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to make the error path simpler.
The goto is replaced with direct return, unneeded label err is
dropped. Also, remove redundant ot200_led_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to simplify error path.
An unnecessary check of ret is replaced with a direct return
Also, remove redundant hp6xxled_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.

To be compatible with the change, goto is replaced with direct
return, unneeded label err_null is dropped and unnecessary variable
retval is removed. Also, remove redundant cobalt_qube_led_remove.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

Pull memremap fix from Dan Williams:
 "The new memremap() api introduced in the 4.3 cycle to unify/replace
  ioremap_cache() and ioremap_wt() is mishandling the highmem case.
  This patch has received a build success notification from a
  0day-kbuild-robot run and has received an ack from Ard"

From the commit message:
 "The impact of this bug is low for now since the pmem driver is the
  only user of memremap(), but this is important to fix before more
  conversions to memremap arrive in 4.4"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  memremap: fix highmem support

Pull x86 fixes from Thomas Gleixner:
 "This set of updates contains:

   - Another bugfix for the pathologic vm86 machinery.  Clear
     thread.vm86 on fork to prevent corrupting the parent state.  This
     comes along with an update to the vm86 selftest case

   - Fix another corner case in the ioapic setup code which causes a
     boot crash on some oddball systems

   - Fix the fallout from the dma allocation consolidation work, which
     leads to a NULL pointer dereference when the allocation code is
     called with a NULL device"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vm86: Set thread.vm86 to NULL on fork/clone
  selftests/x86: Add a fork() to entry_from_vm86 to catch fork bugs
  x86/ioapic: Prevent NULL pointer dereference in setup_ioapic_dest()
  x86/dma-mapping: Fix arch_dma_alloc_attrs() oops with NULL dev

Pull timer fixes from Thomas Gleixner:
 "The last round of minimalistic fixes for clocksource drivers:

   - Prevent multiple shutdown of the sh_mtu2 clocksource

   - Annotate a bunch of clocksource/schedclock functions with notrace
     to prevent an annoying ftrace recursion issue"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/sh_mtu2: Fix multiple shutdown call issue
  clocksource/drivers/digicolor: Prevent ftrace recursion
  clocksource/drivers/fsl_ftm_timer: Prevent ftrace recursion
  clocksource/drivers/vf_pit_timer: Prevent ftrace recursion
  clocksource/drivers/prima2: Prevent ftrace recursion
  clocksource/drivers/samsung_pwm_timer: Prevent ftrace recursion
  clocksource/drivers/pistachio: Prevent ftrace recursion
  clocksource/drivers/arm_global_timer: Prevent ftrace recursion

Pull irq fixes from Thomas Gleixner:
 "The last two one-liners for 4.3 from the irqchip space:

   - Regression fix for armada SoC which addresses the fallout from the
     set_irq_flags() cleanup

   - Add the missing propagation of the irq_set_type() callback to the
     parent interrupt controller of the tegra interrupt chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/tegra: Propagate IRQ type setting to parent
  irqchip/armada-370-xp: Fix regression by clearing IRQ_NOAUTOEN

Pull ARM SoC fixes from Olof Johansson:
 "This should be our final batch of fixes for 4.3:

   - A patch from Sudeep Holla that fixes annotation of wakeup sources
     properly, old unused format seems to have spread through copying.

   - Two patches from Tony for OMAP.  One dealing with MUSB setup
     problems due to runtime PM being enabled too early on the parent
     device.  The other fixes IRQ numbering for OMAP1"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  usb: musb: omap2430: Fix regression caused by driver core change
  ARM: OMAP1: fix incorrect INT_DMA_LCD
  ARM: dts: fix gpio-keys wakeup-source property

Pull SCSI fixes from James Bottomley:
 "This is three essential bug fixes for various SCSI parts.

  The only affected users are SCSI multi-path via device handler
  (basically all the enterprise) and mvsas users.  The dh bugs are an
  async entanglement in boot resulting in a serious WARN_ON trip and a
  use after free on remove leading to a crash with strict memory
  accounting.  The mvsas bug manifests as a null deref oops but only on
  abort sequences; however, these can commonly occur with SATA attached
  devices, hence the fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi_dh: don't try to load a device handler during async probing
  scsi_dh: fix use-after-free when removing scsi device
  mvsas: Fix NULL pointer dereference in mvs_slot_task_free

Pull md bug fixes from Neil Brown:
 "Two more bug fixes for md.

  One bugfix for a list corruption in raid5 because of incorrect
  locking.

  Other for possible data corruption when a recovering device is failed,
  removed, and re-added.

  Both tagged for -stable"

* tag 'md/4.3-rc7-fixes' of git://neil.brown.name/md:
  Revert "md: allow a partially recovered device to be hot-added to an array."
  md/raid5: fix locking in handle_stripe_clean_event()

Pull drm fixes from Dave Airlie:
 "Two drm atomic core fixes.

  And two radeon patches needed to fix a backlight regression on some
  older hardware"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Correct arguments to list_tail_add in create blob ioctl
  drm: crtc: integer overflow in drm_property_create_blob()
  drm/radeon: fix dpms when driver backlight control is disabled
  drm/radeon: move bl encoder assignment into bl init

Pull Ceph fix from Sage Weil:
 "This sets the stable pages flag on the RBD block device when we have
  CRCs enabled.  (This is necessary since the default assumption for
  block devices changed in 3.9)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: require stable pages if message data CRCs are enabled

Pull overlayfs bug fixes from Miklos Szeredi:
 "This contains fixes for bugs that appeared in earlier kernels (all are
  marked for -stable)"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: free lower_mnt array in ovl_put_super
  ovl: free stack of paths in ovl_fill_super
  ovl: fix open in stacked overlay
  ovl: fix dentry reference leak
  ovl: use O_LARGEFILE in ovl_copy_up()

Pull networking fixes from David Miller:

 1) Fix two regressions in ipv6 route lookups, particularly wrt output
    interface specifications in the lookup key.  From David Ahern.

 2) Fix checks in ipv6 IPSEC tunnel pre-encap fragmentation, from
    Herbert Xu.

 3) Fix mis-advertisement of 1000BASE-T on bcm63xx_enet, from Simon
    Arlott.

 4) Some smsc phys misbehave with energy detect mode enabled, so add a
    DT property and disable it on such switches.  From Heiko Schocher.

 5) Fix TSO corruption on TX in mv643xx_eth, from Philipp Kirchhofer.

 6) Fix regression added by removal of openvswitch vport stats, from
    James Morse.

 7) Vendor Kconfig options should be bool, not tristate, from Andreas
    Schwab.

 8) Use non-_BH() net stats bump in tcp_xmit_probe_skb(), otherwise we
    barf during TCP REPAIR operations.

 9) Fix various bugs in openvswitch conntrack support, from Joe
    Stringer.

10) Fix NETLINK_LIST_MEMBERSHIPS locking, from David Herrmann.

11) Don't have VSOCK do sock_put() in interrupt context, from Jorgen
    Hansen.

12) Fix skb_realloc_headroom() failures properly in ISDN, from Karsten
    Keil.

13) Add some device IDs to qmi_wwan, from Bjorn Mork.

14) Fix ovs egress tunnel information when using lwtunnel devices, from
    Pravin B Shelar.

15) Add missing NETIF_F_FRAGLIST to macvtab feature list, from Jason
    Wang.

16) Fix incorrect handling of throw routes when the result of the throw
    cannot find a match, from Xin Long.

17) Protect ipv6 MTU calculations from wrap-around, from Hannes Frederic
    Sowa.

18) Fix failed autonegotiation on KSZ9031 micrel PHYs, from Nathan
    Sullivan.

19) Add missing memory barries in descriptor accesses or xgbe driver,
    from Thomas Lendacky.

20) Fix release conditon test in pppoe_release(), from Guillaume Nault.

21) Fix gianfar bugs wrt filter configuration, from Claudiu Manoil.

22) Fix violations of RX buffer alignment in sh_eth driver, from Sergei
    Shtylyov.

23) Fixing missing of_node_put() calls in various places around the
    networking, from Julia Lawall.

24) Fix incorrect leaf now walking in ipv4 routing tree, from Alexander
    Duyck.

25) RDS doesn't check pskb_pull()/pskb_trim() return values, from
    Sowmini Varadhan.

26) Fix VLAN configuration in mlx4 driver, from Jack Morgenstein.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
  ipv6: protect mtu calculation of wrap-around and infinite loop by rounding issues
  Revert "Merge branch 'ipv6-overflow-arith'"
  net/mlx4: Copy/set only sizeof struct mlx4_eqe bytes
  net/mlx4_en: Explicitly set no vlan tags in WQE ctrl segment when no vlan is present
  vhost: fix performance on LE hosts
  bpf: sample: define aarch64 specific registers
  amd-xgbe: Fix race between access of desc and desc index
  RDS-TCP: Recover correctly from pskb_pull()/pksb_trim() failure in rds_tcp_data_recv
  forcedeth: fix unilateral interrupt disabling in netpoll path
  openvswitch: Fix skb leak using IPv6 defrag
  ipv6: Export nf_ct_frag6_consume_orig()
  openvswitch: Fix double-free on ip_defrag() errors
  fib_trie: leaf_walk_rcu should not compute key if key is less than pn->key
  net: mv643xx_eth: add missing of_node_put
  ath6kl: add missing of_node_put
  net: phy: mdio: add missing of_node_put
  netdev/phy: add missing of_node_put
  net: netcp: add missing of_node_put
  net: thunderx: add missing of_node_put
  ipv6: gre: support SIT encapsulation
  ...

thread.vm86 points to per-task information -- the pointer should not
be copied on clone.

Fixes: d4ce0f26 ("x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Stas Sergeev <stsp@list.ru>
Link: http://lkml.kernel.org/r/71c5d6985d70ec8197c8d72f003823c81b7dcf99.1446270067.git.luto@kernel.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Mere possession of vm86 state is strange.  Make sure that nothing
gets corrupted if we fork after calling vm86().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Stas Sergeev <stsp@list.ru>
Link: http://lkml.kernel.org/r/08f83295460a80e41dc5e3e81ec40d6844d316f5.1446270067.git.luto@kernel.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull input layer fixes from Dmitry Torokhov:

 - a change to the ALPS driver where we had limit the quirk for
   trackstick handling from being active on all Dells to just a few
   models

 - a fix for a build dependency issue in the sur40 driver

 - a small clock handling fixup in the LPC32xx touchscreen driver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - only the Dell Latitude D420/430/620/630 have separate stick button bits
  Input: sur40 - add dependency on VIDEO_V4L2
  Input: lpc32xx_ts - fix warnings caused by enabling unprepared clock

Pull PCI fix from Bjorn Helgaas:
 "Sorry for this last-minute update; it's been in -next for quite a
  while, but I forgot about it until I started getting ready for the
  merge window.

  It's small and fixes a way a user could cause a panic via sysfs, so I
  think it's worth getting it in v4.3.

  NUMA:
    - Prevent out of bounds access in sysfs numa_node override (Sasha Levin)"

* tag 'pci-v4.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Prevent out of bounds access in numa_node override

Merge tag 'omap-for-v4.3/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two omap regression fixes:

- Fix omap3 MUSB with DMA caused by driver core changes

- Fix LCD DMA interrupt number for omap1 that did not
  get changed for sparse IRQ changes

* tag 'omap-for-v4.3/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  usb: musb: omap2430: Fix regression caused by driver core change
  ARM: OMAP1: fix incorrect INT_DMA_LCD
Signed-off-by: Olof Johansson <olof@lixom.net>

Arguments passed to list_add_tail were reversed resulting in deletion
of old blob property everytime the new one is added.

Fixes

commit e2f5d2ea
Author: Daniel Stone <daniels@collabora.com>
Date:   Fri May 22 13:34:51 2015 +0100

    drm/mode: Add user blob-creation ioctl
Signed-off-by: Maneet Singh <mmaneetsingh@nvidia.com>
[seanpaul tweaked commit subject a little]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: stable@kernel.org # v4.2
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

This reverts commit 7eb41885.

This commit is poorly justified, I can find not discusison in email,
and it clearly causes a problem.

If a device which is being recovered fails and is subsequently
re-added to an array, there could easily have been changes to the
array *before* the point where the recovery was up to.  So the
recovery must start again from the beginning.

If a spare is being recovered and fails, then when it is re-added we
really should do a bitmap-based recovery up to the recovery-offset,
and then a full recovery from there.  Before this reversion, we only
did the "full recovery from there" which is not corect.  After this
reversion with will do a full recovery from the start, which is safer
but not ideal.

It will be left to a future patch to arrange the two different styles
of recovery.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: stable@vger.kernel.org (3.14+)
Fixes: 7eb41885 ("md: allow a partially recovered device to be hot-added to an array.")

The size here comes from the user via the ioctl, it is a number between
1-u32max so the addition here could overflow on 32 bit systems.

Fixes: f453ba04 ('DRM: add mode setting support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Cc: stable@kernel.org # v4.2
Signed-off-by: Dave Airlie <airlied@gmail.com>

Pull arm64 fixes from Will Deacon:
 "Apologies for this being so late, but we've uncovered a few nasty
  issues on arm64 which didn't settle down until yesterday and the fixes
  all look suitable for 4.3.  Of the four patches, three of them are
  Cc'd to stable, with the remaining patch fixing an issue that only
  took effect during the merge window.

  Summary:

   - Fix corruption in SWP emulation when STXR fails due to contention
   - Fix MMU re-initialisation when resuming from a low-power state
   - Fix stack unwinding code to match what ftrace expects
   - Fix relocation code in the EFI stub when DRAM base is not 2MB aligned"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64/efi: do not assume DRAM base is aligned to 2 MB
  Revert "ARM64: unwind: Fix PC calculation"
  arm64: kernel: fix tcr_el1.t0sz restore on systems with extended idmap
  arm64: compat: fix stxr failure case in SWP emulation

Pull ia64 kcmp syscall from Tony Luck:
 "Missed adding the kcmp() syscall a long time ago.  Now it seems that
  it is essential to build systemd"

* tag 'please-pull-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Wire up kcmp syscall

After commit 566c09c5 ("raid5: relieve lock contention in get_active_stripe()")
__find_stripe() is called under conf->hash_locks + hash.
But handle_stripe_clean_event() calls remove_hash() under
conf->device_lock.

Under some cirscumstances the hash chain can be circuited,
and we get an infinite loop with disabled interrupts and locked hash
lock in __find_stripe(). This leads to hard lockup on multiple CPUs
and following system crash.

I was able to reproduce this behavior on raid6 over 6 ssd disks.
The devices_handle_discard_safely option should be set to enable trim
support. The following script was used:

for i in `seq 1 32`; do
    dd if=/dev/zero of=large$i bs=10M count=100 &
done

neilb: original was against a 3.x kernel.  I forward-ported
  to 4.3-rc.  This verison is suitable for any kernel since
  Commit: 59fc630b ("RAID5: batch adjacent full stripe write")
  (v4.1+).  I'll post a version for earlier kernels to stable.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Fixes: 566c09c5 ("raid5: relieve lock contention in get_active_stripe()")
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org> # 3.13 - 4.2

rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.

But since kernel 3.9 (patch 1d1d1a76
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.

This patch sets the necessary flag to get stable pages back for rbd.

In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).

Cc: stable@vger.kernel.org # 3.9+, needs backporting
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

regression fix for backlight on old laptops.

* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dpms when driver backlight control is disabled
  drm/radeon: move bl encoder assignment into bl init

The current arm64 Image relocation code in the UEFI stub assumes that
the dram_base argument it receives is always a multiple of 2 MB. In
reality, it is simply the lowest start address of all RAM entries in
the UEFI memory map, which means it could be any multiple of 4 KB.

Since the arm64 kernel Image needs to reside TEXT_OFFSET bytes beyond
a 2 MB aligned base, or it will fail to boot, make sure we round dram_base
to 2 MB before using it to calculate the relocation address.

Fixes: e38457c3 ("arm64: efi: prefer AllocatePages() over efi_low_alloc() for vmlinux")
Reported-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

If driver backlight control is disabled, either by driver
parameter or default per-asic setting, revert to the old behavior.

Fixes a regression in commit:
4281f46eReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org