- 27 Apr, 2015 8 commits
-
-
Eric W. Biederman authored
commit 2bb77ab4 upstream. Replace kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Eric W. Biederman authored
commit 989c9ba1 upstream. Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by:
-
Eric W. Biederman authored
commit a2ccd2e4 upstream. Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by:
-
Eric W. Biederman authored
commit 508f81d5 upstream. Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit as it can be called in both hard irq and other contexts. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit b50edd78 ] I noticed tcpdump was giving funky timestamps for locally generated SYNACK messages on loopback interface. 11:42:46.938990 IP 127.0.0.1.48245 > 127.0.0.2.23850: S 945476042:945476042(0) win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7> 20:28:58.502209 IP 127.0.0.2.23850 > 127.0.0.1.48245: S 3160535375:3160535375(0) ack 945476043 win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7> This is because we need to clear skb->tstamp before entering lower stack, otherwise net_timestamp_check() does not set skb->tstamp. Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 666b8051 ] On processing cumulative ACKs, the FRTO code was not checking the SACKed bit, meaning that there could be a spurious FRTO undo on a cumulative ACK of a previously SACKed skb. The FRTO code should only consider a cumulative ACK to indicate that an original/unretransmitted skb is newly ACKed if the skb was not yet SACKed. The effect of the spurious FRTO undo would typically be to make the connection think that all previously-sent packets were in flight when they really weren't, leading to a stall and an RTO. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO") Signed-off-by:
-
D.S. Ljungmark authored
[ Upstream commit 6fd99094 ] A local route may have a lower hop_limit set than global routes do. RFC 3756, Section 4.2.7, "Parameter Spoofing" > 1. The attacker includes a Current Hop Limit of one or another small > number which the attacker knows will cause legitimate packets to > be dropped before they reach their destination. > As an example, one possible approach to mitigate this threat is to > ignore very small hop limits. The nodes could implement a > configurable minimum hop limit, and ignore attempts to set it below > said limit. Signed-off-by:
D.S. Ljungmark <ljungmark@modio.se> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Michal Kubeček authored
[ Upstream commit d0c294c5 ] On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux() struct dst_entry *dst = sk->sk_rx_dst; if (dst) dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie); to code reading sk->sk_rx_dst twice, once for the test and once for the argument of ip6_dst_check() (dst_check() is inline). This allows ip6_dst_check() to be called with null first argument, causing a crash. Protect sk->sk_rx_dst access by ACCESS_ONCE() both in IPv4 and IPv6 TCP early demux code. Fixes: 41063e9d ("ipv4: Early TCP socket demux.") Fixes: c7109986 ("ipv6: Early TCP socket demux") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
-
- 22 Apr, 2015 32 commits
-
-
Mark Brown authored
commit ee23794b upstream. arm64 is unlikely to have a VGA console and does not export screen_info causing build failures if the driver is build, for example in all*config. Add a dependency on !ARM64 to prevent this. This list is getting quite long, it may be easier to depend on a symbol which architectures that do support the driver can select. Signed-off-by:
Mark Brown <broonie@linaro.org> [tomi.valkeinen@ti.com: moved && to first modified line] Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Chen Gang authored
[media] drivers: media: usb: b2c2: use usb_*_coherent() instead of pci_*_consistent() in flexcop-usb.c commit 6c7e3469 upstream. Some architectures do not support PCI, but still support USB, so need let our usb driver try to use usb_* instead of pci_* to support these architectures, or can not pass compiling. The related error (with allmodconfig for arc): CC [M] drivers/media/usb/b2c2/flexcop-usb.o drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_exit’: drivers/media/usb/b2c2/flexcop-usb.c:393: error: implicit declaration of function ‘pci_free_consistent’ drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_init’: drivers/media/usb/b2c2/flexcop-usb.c:410: error: implicit declaration of function ‘pci_alloc_consistent’ Signed-off-by:
Chen Gang <gang.chen@asianux.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
-
Majd Dibbiny authored
commit 61a3855b upstream. For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of overflow, according to the IB spec, we have to saturate a counter to its max value, do that. Fixes: c3779134 ('IB/mlx4: Support PMA counters for IBoE') Signed-off-by:
Majd Dibbiny <majd@mellanox.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Sasha Levin authored
commit 6b8d9117 upstream. The timeout entries are sizeof(int) rather than sizeof(long), which means that when they were getting read we'd also leak kernel memory to userspace along with the timeout values. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Sasha Levin authored
commit db27ebb1 upstream. Max unacked packets/bytes is an int while sizeof(long) was used in the sysctl table. This means that when they were getting read we'd also leak kernel memory to userspace along with the timeout values. Signed-off-by:
-
Marek Szyprowski authored
commit 05b676ab upstream. TASK_SIZE is depends on the systems architecture (32 or 64 bits) and it should not be used for defining offset boundary for mmaping buffers for CAPTURE and OUTPUT queues. This patch fixes support for MMAP calls on the CAPTURE queue on 64bit architectures (like ARM64). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Hans Verkuil authored
commit ab312030 upstream. The v4l2_dev field of struct video_device must be set correctly. This was never done for this driver, so no video nodes were created anymore. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Mike Christie authored
commit b815fc12 upstream. This fixes a oops due to a double list add when adding a reject PDU for iscsit_allocate_iovecs allocation failures. The cmd has already been added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call iscsit_reject_cmd. Note that for ERL0 the reject PDU is not actually sent, so this patch is not completely tested. Just verified we do not oops. The problem is the add reject functions return -1 which is returned all the way up to iscsi_target_rx_thread which for ERL0 will drop the connection. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Al Viro authored
commit deeb8525 upstream. If we fail past the aio_setup_ring(), we need to destroy the mapping. We don't need to care about anybody having found ctx, or added requests to it, since the last failure exit is exactly the failure to make ctx visible to lookups. Reproducer (based on one by Joe Mario <jmario@redhat.com>): void count(char *p) { char s[80]; printf("%s: ", p); fflush(stdout); sprintf(s, "/bin/cat /proc/%d/maps|/bin/fgrep -c '/[aio] (deleted)'", getpid()); system(s); } int main() { io_context_t *ctx; int created, limit, i, destroyed; FILE *f; count("before"); if ((f = fopen("/proc/sys/fs/aio-max-nr", "r")) == NULL) perror("opening aio-max-nr"); else if (fscanf(f, "%d", &limit) != 1) fprintf(stderr, "can't parse aio-max-nr\n"); else if ((ctx = calloc(limit, sizeof(io_context_t))) == NULL) perror("allocating aio_context_t array"); else { for (i = 0, created = 0; i < limit; i++) { if (io_setup(1000, ctx + created) == 0) created++; } for (i = 0, destroyed = 0; i < created; i++) if (io_destroy(ctx[i]) == 0) destroyed++; printf("created %d, failed %d, destroyed %d\n", created, limit - created, destroyed); count("after"); } } Found-by:
Joe Mario <jmario@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 64b4e252 upstream. "ocfs2 syncs the wrong range" had been broken; prior to it the code was doing the wrong thing in case of O_APPEND, all right, but _after_ it we were syncing the wrong range in 100% cases. *ppos, aka iocb->ki_pos is incremented prior to that point, so we are always doing sync on the area _after_ the one we'd written to. Spotted by Joseph Qi <joseph.qi@huawei.com> back in January; unfortunately, I'd missed his mail back then ;-/ Signed-off-by:
-
John Soni Jose authored
commit 2e7cee02 upstream. Kernel panic was happening as iscsi_host_remove() was called on a host which was not yet added. Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Reviewed-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
David Disseldorp authored
commit e1e9bda2 upstream. Under intermittent network outages, find_writable_file() is susceptible to the following race condition, which results in a user-after-free in the cifs_writepages code-path: Thread 1 Thread 2 ======== ======== inv_file = NULL refind = 0 spin_lock(&cifs_file_list_lock) // invalidHandle found on openFileList inv_file = open_file // inv_file->count currently 1 cifsFileInfo_get(inv_file) // inv_file->count = 2 spin_unlock(&cifs_file_list_lock); cifs_reopen_file() cifs_close() // fails (rc != 0) ->cifsFileInfo_put() spin_lock(&cifs_file_list_lock) // inv_file->count = 1 spin_unlock(&cifs_file_list_lock) spin_lock(&cifs_file_list_lock); list_move_tail(&inv_file->flist, &cifs_inode->openFileList); spin_unlock(&cifs_file_list_lock); cifsFileInfo_put(inv_file); ->spin_lock(&cifs_file_list_lock) // inv_file->count = 0 list_del(&cifs_file->flist); // cleanup!! kfree(cifs_file); spin_unlock(&cifs_file_list_lock); spin_lock(&cifs_file_list_lock); ++refind; // refind = 1 goto refind_writable; At this point we loop back through with an invalid inv_file pointer and a refind value of 1. On second pass, inv_file is not overwritten on openFileList traversal, and is subsequently dereferenced. Signed-off-by:
David Disseldorp <ddiss@suse.de> Reviewed-by:
Jeff Layton <jlayton@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Peter Hurley authored
commit fb5ef9e7 upstream. In canon mode, the read buffer head will advance over the buffer tail if the input > 4095 bytes without receiving a line termination char. Discard additional input until a line termination is received. Before evaluating for overflow, the 'room' value is normalized for I_PARMRK and 1 byte is reserved for line termination (even in !icanon mode, in case the mode is switched). The following table shows the transform: actual buffer | 'room' value before overflow calc space avail | !I_PARMRK | I_PARMRK -------------------------------------------------- 0 | -1 | -1 1 | 0 | 0 2 | 1 | 0 3 | 2 | 0 4+ | 3 | 1 When !icanon or when icanon and the read buffer contains newlines, normalized 'room' values of -1 and 0 are clamped to 0, and 'overflow' is 0, so read_head is not adjusted and the input i/o loop exits (setting no_room if called from flush_to_ldisc()). No input is discarded since the reader does have input available to read which ensures forward progress. When icanon and the read buffer does not contain newlines and the normalized 'room' value is 0, then overflow and room are reset to 1, so that the i/o loop will process the next input char normally (except for parity errors which are ignored). Thus, erasures, signalling chars, 7-bit mode, etc. will continue to be handled properly. If the input char processed was not a line termination char, then the canon_head index will not have advanced, so the normalized 'room' value will now be -1 and 'overflow' will be set, which indicates the read_head can safely be reset, effectively erasing the last char processed. If the input char processed was a line termination, then the canon_head index will have advanced, so 'overflow' is cleared to 0, the read_head is not reset, and 'room' is cleared to 0, which exits the i/o loop (because the reader now have input available to read which ensures forward progress). Note that it is possible for a line termination to be received, and for the reader to copy the line to the user buffer before the input i/o loop is ready to process the next input char. This is why the i/o loop recomputes the room/overflow state with every input char while handling overflow. Finally, if the input data was processed without receiving a line termination (so that overflow is still set), the pty driver must receive a write wakeup. A pty writer may be waiting to write more data in n_tty_write() but without unthrottling here that wakeup will not arrive, and forward progress will halt. (Normally, the pty writer is woken when the reader reads data out of the buffer and more space become available). Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com>
-
Stefan Agner authored
commit 8e4934c6 upstream. When the receiver was enabled during startup, a character could have been in the FIFO when the UART get initially used. The driver configures the (receive) watermark level, and flushes the FIFO. However, the receive flag (RDRF) could still be set at that stage (as mentioned in the register description of UARTx_RWFIFO). This leads to an interrupt which won't be handled properly in interrupt mode: The receive interrupt function lpuart_rxint checks the FIFO count, which is 0 at that point (due to the flush during initialization). The problem does not manifest when using DMA to receive characters. Fix this situation by explicitly read the status register, which leads to clearing of the RDRF flag. Due to the flush just after the status flag read, a explicit data read is not to required. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Lu Baolu authored
commit 227a4fd8 upstream. When a device with an isochronous endpoint is plugged into the Intel xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under Intel xHCI host controllers, if the event ring is full of events from transfers with BEI set, an "Event Ring is Full" event will be posted to the last entry of the event ring, but no interrupt is generated. Host will cease all transfer and command executions and wait until software completes handling the pending events in the event ring. That means xHC stops, but event of "event ring is full" is not notified. As the result, the xHC looks like dead to user. This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And it should be backported to kernels as old as 3.0, that contains the commit 69e848c2 ("Intel xhci: Support EHCI/xHCI port switching."). Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Tested-by:
Alistair Grant <akgrant0710@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Lu Baolu authored
commit 9425183d upstream. Linux xHCI driver doesn't report and handle port cofig error change. If Port Configure Error for root hub port occurs, CEC bit in PORTSC would be set by xHC and remains 1. This happends when the root port fails to configure its link partner, e.g. the port fails to exchange port capabilities information using Port Capability LMPs. Then the Port Status Change Events will be blocked until all status change bits(CEC is one of the change bits) are cleared('0') (refer to xHCI spec 4.19.2). Otherwise, the port status change event for this root port will not be generated anymore, then root port would look like dead for user and can't be recovered until a Host Controller Reset(HCRST). This patch is to check CEC bit in PORTSC in xhci_get_port_status() and set a Config Error in the return status if CEC is set. This will cause a ClearPortFeature request, where CEC bit is cleared in xhci_clear_port_change_bit(). [The commit log is based on initial Marvell patch posted at http://marc.info/?l=linux-kernel&m=142323612321434&w=2] Reported-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Andreas Werner authored
commit 555828ef upstream. Return EPROBE_DEFER if Regulator returns EPROBE_DEFER If the Flexcan driver is built into kernel and a regulator is used to enable the CAN transceiver, the Flexcan driver may not use the regulator. When initializing the Flexcan device with a regulator defined in the device tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence the Flexcan init fails. The solution for this is to return EPROBE_DEFER if regulator is not initialized and wait until the regulator is initialized. Signed-off-by:
Andreas Werner <kernel@andy89.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Stefan Lippers-Hollmann authored
commit 80313b30 upstream. The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in both BIOS and UEFI mode while rebooting unless reboot=pci is used. Add a quirk to reboot via the pci method. The problem is very intermittent and hard to debug, it might succeed rebooting just fine 40 times in a row - but fails half a dozen times the next day. It seems to be slightly less common in BIOS CSM mode than native UEFI (with the CSM disabled), but it does happen in either mode. Since I've started testing this patch in late january, rebooting has been 100% reliable. Most of the time it already hangs during POST, but occasionally it might even make it through the bootloader and the kernel might even start booting, but then hangs before the mode switch. The same symptoms occur with grub-efi, gummiboot and grub-pc, just as well as (at least) kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16). Upgrading to the most current mainboard firmware of the ASRock Q1900DC-ITX, version 1.20, does not improve the situation. ( Searching the web seems to suggest that other Bay Trail-D mainboards might be affected as well. ) -- Signed-off-by:
Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Matt Fleming <matt.fleming@intel.com> Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mirSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Ujfalusi authored
commit 02d88b73 upstream. In omap_dma_start_desc the vdesc->node is removed from the virt-dma framework managed lists (to be precise from the desc_issued list). If a terminate_all comes before the transfer finishes the omap_desc will not be freed up because it is not in any of the lists and we stopped the DMA channel so the transfer will not going to complete. There is no special sequence for leaking memory when using cyclic (audio) transfer: with every start and stop of a cyclic transfer the driver leaks struct omap_desc worth of memory. Free up the allocated memory directly in omap_dma_terminate_all() since the framework will not going to do that for us. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> CC: <linux-omap@vger.kernel.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Darshana Padmadas authored
commit 4ce7ca89 upstream. This patch uses iio_trigger_get to increment the reference count of trigger device, to avoid incorrect assignment. Can result in a null pointer dereference during removal if the trigger has been changed before removal. This patch refers to a similar situation encountered through the following discussion: http://www.spinics.net/lists/linux-iio/msg13669.htmlSigned-off-by:
Darshana Padmadas <darshanapadmadas@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Viorel Suman authored
commit 4dac0a8e upstream. A hardware fifo reset always imply an invalidation of the existing timestamps, so we'll clear timestamps fifo on successfull hardware fifo reset. Signed-off-by:
Viorel Suman <viorel.suman@gmail.com> Signed-off-by:
-
Bart Van Assche authored
commit bba0bdd7 upstream. SCSI transport drivers and SCSI LLDs block a SCSI device if the transport layer is not operational. This means that in this state no requests should be processed, even if the REQ_PREEMPT flag has been set. This patch avoids that a rescan shortly after a cable pull sporadically triggers the following kernel oops: BUG: unable to handle kernel paging request at ffffc9001a6bc084 IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib] Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100) Call Trace: [<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp] [<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp] [<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod] [<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod] [<ffffffff81223b37>] __blk_run_queue+0x27/0x30 [<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110 [<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0 [<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod] [<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod] [<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod] [<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod] [<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod] [<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod] [<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod] [<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod] [<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160 [<ffffffff811589de>] vfs_write+0xce/0x140 [<ffffffff81158b53>] sys_write+0x53/0xa0 [<ffffffff81464592>] system_call_fastpath+0x16/0x1b [<00007f611c9d9300>] 0x7f611c9d92ff Reported-by:
Max Gurtuvoy <maxg@mellanox.com> Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
-
Doug Goldstein authored
commit b229a0f8 upstream. This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order to avoid attaching a TTY to the JTAG port as this board is based on the CALAO Systems reference design and needs the same fix up. Signed-off-by:
Doug Goldstein <cardoe@cardoe.com> [johan: clean up probe logic ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Doug Goldstein authored
commit 4899c054 upstream. Synapse Wireless uses the FTDI VID with a custom PID of 0x9090 for their SNAP Stick 200 product. Signed-off-by:
-
David Miller authored
commit f2c9e560 upstream. Use readb() and memcpy_fromio() accessors instead. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Tejun Heo authored
commit c72efb65 upstream. From 1ebf33901ecc75d9496862dceb1ef0377980587c Mon Sep 17 00:00:00 2001 From: Tejun Heo <tj@kernel.org> Date: Mon, 23 Mar 2015 00:08:19 -0400 2f800fbd ("writeback: fix dirtied pages accounting on redirty") introduced account_page_redirty() which reverts stat updates for a redirtied page, making BDI_DIRTIED no longer monotonically increasing. bdi_update_write_bandwidth() uses the delta in BDI_DIRTIED as the basis for bandwidth calculation. While unlikely, since the above patch, the newer value may be lower than the recorded past value and underflow the bandwidth calculation leading to a wild result. Fix it by subtracing min of the old and new values when calculating delta. AFAIK, there hasn't been any report of it happening but the resulting erratic behavior would be non-critical and temporary, so it's possible that the issue is happening without being reported. The risk of the fix is very low, so tagged for -stable. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Greg Thelen <gthelen@google.com> Fixes: 2f800fbd ("writeback: fix dirtied pages accounting on redirty") Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Tejun Heo authored
commit 7d70e154 upstream. global_update_bandwidth() uses static variable update_time as the timestamp for the last update but forgets to initialize it to INITIALIZE_JIFFIES. This means that global_dirty_limit will be 5 mins into the future on 32bit and some large amount jiffies into the past on 64bit. This isn't critical as the only effect is that global_dirty_limit won't be updated for the first 5 mins after booting on 32bit machines, especially given the auxiliary nature of global_dirty_limit's role - protecting against global dirty threshold's sudden dips; however, it does lead to unintended suboptimal behavior. Fix it. Fixes: c42843f2 ("writeback: introduce smoothed global dirty limit") Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Brian Silverman authored
commit 746db944 upstream. When non-realtime tasks get priority-inheritance boosted to a realtime scheduling class, RLIMIT_RTTIME starts to apply to them. However, the counter used for checking this (the same one used for SCHED_RR timeslices) was not getting reset. This meant that tasks running with a non-realtime scheduling class which are repeatedly boosted to a realtime one, but never block while they are running realtime, eventually hit the timeout without ever running for a time over the limit. This patch resets the realtime timeslice counter when un-PI-boosting from an RT to a non-RT scheduling class. I have some test code with two threads and a shared PTHREAD_PRIO_INHERIT mutex which induces priority boosting and spins while boosted that gets killed by a SIGXCPU on non-fixed kernels but doesn't with this patch applied. It happens much faster with a CONFIG_PREEMPT_RT kernel, and does happen eventually with PREEMPT_VOLUNTARY kernels. Signed-off-by:
Brian Silverman <brian@peloton-tech.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: austin@peloton-tech.com Link: http://lkml.kernel.org/r/1424305436-6716-1-git-send-email-brian@peloton-tech.comSigned-off-by:
-
Gu Zheng authored
commit b0dc3a34 upstream. Qiu Xishi reported the following BUG when testing hot-add/hot-remove node under stress condition: BUG: unable to handle kernel paging request at 0000000000025f60 IP: next_online_pgdat+0x1/0x50 PGD 0 Oops: 0000 [#1] SMP ACPI: Device does not support D3cold Modules linked in: fuse nls_iso8859_1 nls_cp437 vfat fat loop dm_mod coretemp mperf crc32c_intel ghash_clmulni_intel aesni_intel ablk_helper cryptd lrw gf128mul glue_helper aes_x86_64 pcspkr microcode igb dca i2c_algo_bit ipv6 megaraid_sas iTCO_wdt i2c_i801 i2c_core iTCO_vendor_support tg3 sg hwmon ptp lpc_ich pps_core mfd_core acpi_pad rtc_cmos button ext3 jbd mbcache sd_mod crc_t10dif scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc scsi_dh ahci libahci libata scsi_mod [last unloaded: rasf] CPU: 23 PID: 238 Comm: kworker/23:1 Tainted: G O 3.10.15-5885-euler0302 #1 Hardware name: HUAWEI TECHNOLOGIES CO.,LTD. Huawei N1/Huawei N1, BIOS V100R001 03/02/2015 Workqueue: events vmstat_update task: ffffa800d32c0000 ti: ffffa800d32ae000 task.ti: ffffa800d32ae000 RIP: 0010: next_online_pgdat+0x1/0x50 RSP: 0018:ffffa800d32afce8 EFLAGS: 00010286 RAX: 0000000000001440 RBX: ffffffff81da53b8 RCX: 0000000000000082 RDX: 0000000000000000 RSI: 0000000000000082 RDI: 0000000000000000 RBP: ffffa800d32afd28 R08: ffffffff81c93bfc R09: ffffffff81cbdc96 R10: 00000000000040ec R11: 00000000000000a0 R12: ffffa800fffb3440 R13: ffffa800d32afd38 R14: 0000000000000017 R15: ffffa800e6616800 FS: 0000000000000000(0000) GS:ffffa800e6600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000025f60 CR3: 0000000001a0b000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: refresh_cpu_vm_stats+0xd0/0x140 vmstat_update+0x11/0x50 process_one_work+0x194/0x3d0 worker_thread+0x12b/0x410 kthread+0xc6/0xd0 ret_from_fork+0x7c/0xb0 The cause is the "memset(pgdat, 0, sizeof(*pgdat))" at the end of try_offline_node, which will reset all the content of pgdat to 0, as the pgdat is accessed lock-free, so that the users still using the pgdat will panic, such as the vmstat_update routine. process A: offline node XX: vmstat_updat() refresh_cpu_vm_stats() for_each_populated_zone() find online node XX cond_resched() offline cpu and memory, then try_offline_node() node_set_offline(nid), and memset(pgdat, 0, sizeof(*pgdat)) zone = next_zone(zone) pg_data_t *pgdat = zone->zone_pgdat; // here pgdat is NULL now next_online_pgdat(pgdat) next_online_node(pgdat->node_id); // NULL pointer access So the solution here is postponing the reset of obsolete pgdat from try_offline_node() to hotadd_new_pgdat(), and just resetting pgdat->nr_zones and pgdat->classzone_idx to be 0 rather than the memset 0 to avoid breaking pointer information in pgdat. Signed-off-by:
Gu Zheng <guz.fnst@cn.fujitsu.com> Reported-by:
Xishi Qiu <qiuxishi@huawei.com> Suggested-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Taku Izumi <izumi.taku@jp.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Sudip Mukherjee authored
commit ff6b8090 upstream. we have already allocated memory for nbd_dev, but we were not releasing that memory and just returning the error value. Signed-off-by:
Sudip Mukherjee <sudip@vectorindia.org> Acked-by:
Paul Clements <Paul.Clements@SteelEye.com> Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Signed-off-by:
-
Emmanuel Grumbach authored
commit 9c8928f5 upstream. The assumption before this patch was that we don't need to run again the INIT firmware after the system booted. The INIT firmware runs calibrations which impact the physical layer's behavior. Users reported that it may be helpful to run these calibrations again every time the interface is brought up. The penatly is minimal, since the calibrations run fast. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=94341Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Shachar Raindel authored
commit 8494057a upstream. Properly verify that the resulting page aligned end address is larger than both the start address and the length of the memory area requested. Both the start and length arguments for ib_umem_get are controlled by the user. A misbehaving user can provide values which will cause an integer overflow when calculating the page aligned end address. This overflow can cause also miscalculation of the number of pages mapped, and additional logic issues. Addresses: CVE-2014-8159 Signed-off-by:
Shachar Raindel <raindel@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@mellanox.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
