Based on the values from twl6040 codec (HSOTRIM L/R) we can configure
the McPDM offset cancellation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The offset cancellation values can be different from board to board, even
on the same HW platform.
Provide a way for the machine drivers to configure the McPDM offset
cancellation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Provide API to fetch the TRIM values (for machine drivers)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Update the reg_cache with values from chip regarding to TRIM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ad1980_dai is not used outside this driver,
thus drop exporting it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

sn95031_get_mic_bias() is not used outside this driver
and it is a static function now.
Thus drop exporting sn95031_get_mic_bias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fixes the following compile time warning:
omap-mcbsp.c:519: warning: suggest explicit braces to avoid ambiguous ‘else’
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM1250 EV1 is functionally digital in a system (the analogue I/O
is either ground referenced or always powered) so flag it as idle_bias_off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM1250 EV1 has some GPIOs which can be used to control the behaviour
at runtime. Request them all if supplied and add a set_bias_level()
function to start and stop the clocks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently we force all devices in the system to be at the same bias level.
This is due to concerns about power or pop/click impacts from either
ramping VMID or mismatching VMID on the analogue I/O lines between
connected devices but does mean we power devices up more often than we
really need to.

If a device flags idle_bias_off this will usually mean that it's either
all digital or ground referenced (in which case the idle and powered bias
levels are identical) so this concern does not apply and we can save some
power by leaving it off when not needed itself.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

A supply widget is generally clearer than a MICBIAS widget and a mic bias
is just a type of supply so use a supply widget for the MICBIAS. This also
avoids confusion with the routing when connected to multiple inputs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Matches the register name and avoids confusion with board widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

As we've only got one audio interface and it is symmetric we can just set
SYSCLK based on the sample rate requested by the application layer. Provide
a default so bypass paths work before audio playback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since f0fba2ad "ASoC: multi-component - ASoC Multi-Component Support",
snd_soc_register_codec() now does all the codec list and mutex init.
Thus don't need to call mutex_init(&codec->mutex) in wl1273_probe() any more.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since our irq handler has been called, it is granted, that
the reason was either PLUGINT, or UNPLUGINT.
The INTID register has been checked in the MFD part of
twl6040 driver (twl6040-irq.c).
We have no reason to read from chip again here.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

OMAP4 McPDM supports 5 downlink (playback), and
3 uplink (capture) channels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Attempt to change McBSP CLKS source while another stream is active is not
safe after commit d135865 ("OMAP: McBSP: implement functional clock
switching via clock framework") in 2.6.37.

CLKS parent clock switching using clock framework have to idle the McBSP
before switching and then activate it again. This short break can cause a
DMA transaction error to already running stream which halts and recovers
only by closing and restarting the stream.

This goes more fatal after commit e2fa61d4 ("OMAP3: l3: Introduce
l3-interconnect error handling driver") in 2.6.39 where l3 driver detects a
severe timeout error and does BUG_ON().

Fix this by not changing any configuration in omap_mcbsp_dai_set_dai_sysclk
if the McBSP is already active. This test should have been here just from
the beginning anyway.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The number of times we look at a potentially connected neighbour is just
as important as the number of times we actually recurse into looking at
that neighbour so also collect that statistic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allow the DBVDD2 and DBVDD3 rails to be powered down when idle, helping
fully power down connected devices when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use one set of defines for the HS bits, since they are identical in both
control register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Change the legacy DAI name from "twl6040-hifi" to "twl6040-legacy" to
be more intuitive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

AUX L/R outputs can be driver from the Handsfree PGA output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use "Headset XYZ" for user visible controls, while the internal DAPM
widgets can use "HS XYZ".
In this way we can group the Headset related controls in UI
(alsamixer for example).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use "Handsfree XYZ" for user visible controls, while the internal DAPM
widgets can use "HF XYZ".
In this way we can group the Handsfree related controls in UI
(alsamixer for example).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix the DAPM routing for the earphone path.
Convert the DAPM_SWITCH_E to DAPM_OUT_DRV_E, so we can have correct
power up, and down sequence for EP.
Introduce mute control (Earphone Playback Switch) for users to
enable/disable the EP path.
Note: the EP does not have it's own dedicated DAC. EP is connected to
HSL DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Software only shadow register to be used by the driver.
For example Earpiece path will need this shadow register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Replace the string with plain NULL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Change the register name strings in the comments for the
twl6040_reg table, so it is easier to search for specific
register.

This is cosmetic change.

Before we had for example:
TWL6040_REG_HSLCTL as register definition.

At the register table we had:
TWL6040_HSLCTL

Searching for TWL6040_HSLCTL resulted no hits.

While if we look for REG_HSLCTL, we can find the places
the register has been used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The default gains on outputs/inputs are set to 0dB.
This is fixing the pop noise issue at the first playback, which
caused by the wrong starting point of the ramp code.
The ramp code for the outputs expects the gains to be in
their lowest configuration in order to be effective.
After the playback stops, the ramp code takes care of
ramping down the gains to their minimum.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'peter/topic/for-mark/mcpdm_for-3.2' of git://gitorious.org/omap-audio/linux-audio into for-3.2

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Reasons for the replacement:
The current driver for McPDM was developed to support the legacy mode only.
In preparation for the ABE support the current driver stack need the be
replaced.
The new driver is much simpler, easier to extend, and it also fixes some of the
issues with the old stack.

Main changes:
- single file for omap-mcpdm (mcpdm.c/h removed)
- Define names for registers, bits cleaned up, prefixed
- Full-duplex audio operation (arecord | aplay) has been fixed
- Less code

McPDM need to be turned off after all streams has been stopped.
This might cause pop noise on the output, if the codec's DAC is
still powered at this time.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>