Currently if a rollback ends with error, the vregion is in a zombie
state until end of the existence. Instead of that, rather try to
continue where rollback ended later on (after rehash interval).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the call of rehash_dis trace and the error message to
vregion_migrate() next to the failed_rollback flag set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flag is set by the caller mlxsw_sp_acl_tcam_vregion_migrate() anyway,
so don't set it here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the br_port_exists() macro with its twin from netdevice.h

CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the team_port_exists() macro with its twin from netdevice.h

CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch advertises Forward Error Correction in ethtool
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change t4fw_version.h to update latest firmware version
number to 1.23.3.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently no support for the multicast/broadcast aspects
of VXLAN in ovs. In the datapath flow the tun_dst must specific.
But in the IP_TUNNEL_INFO_BRIDGE mode the tun_dst can not be specific.
And the packet can forward through the fdb table of vxlan devcice. In
this mode the broadcast/multicast packet can be sent through the
following ways in ovs.

ovs-vsctl add-port br0 vxlan -- set in vxlan type=vxlan \
        options:key=1000 options:remote_ip=flow
ovs-ofctl add-flow br0 in_port=LOCAL,dl_dst=ff:ff:ff:ff:ff:ff, \
        action=output:vxlan

bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.1 \
        src_vni 1000 vni 1000 self
bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.2 \
        src_vni 1000 vni 1000 self
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP stack relies on the fact that a freshly allocated skb
has skb->cb[] and skb_shinfo(skb)->tx_flags cleared.

When recycling tx skb, we must ensure these fields are cleared.

Fixes: 472c2e07 ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Innova IPsec driver is part of all Innova drivers, and its
maintainenece is covered by an existing entry in this file.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 36 pedit action tests to check pedit options described in tc-pedit(8)
man page. Test cases can be specified by categories: actions, pedit,
raw_op, layered_op. RAW_OP cases check offset option for u8, u16 and u32
offset size. LAYERED_OP cases check fields option for eth, ip, ip6,
tcp and udp headers.

Include following tests:
377e - Add pedit action with RAW_OP offset u32
a0ca - Add pedit action with RAW_OP offset u32 (INVALID)
dd8a - Add pedit action with RAW_OP offset u16 u16
53db - Add pedit action with RAW_OP offset u16 (INVALID)
5c7e - Add pedit action with RAW_OP offset u8 add value
2893 - Add pedit action with RAW_OP offset u8 quad
3a07 - Add pedit action with RAW_OP offset u8-u16-u8
ab0f - Add pedit action with RAW_OP offset u16-u8-u8
9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert
ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID)
f512 - Add pedit action with RAW_OP offset u16 at offmask shift set
c2cb - Add pedit action with RAW_OP offset u32 retain value
86d4 - Add pedit action with LAYERED_OP eth set src & dst
c715 - Add pedit action with LAYERED_OP eth set src (INVALID)
ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence
5810 - Add pedit action with LAYERED_OP ip set src & dst
1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield
02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol
3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID)
31ae - Add pedit action with LAYERED_OP ip ttl clear/set
486f - Add pedit action with LAYERED_OP ip set duplicate fields
e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag,
nofrag fields
6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport
afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type &
icmp_code
3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID)
fc1f - Add pedit action with LAYERED_OP ip6 set src & dst
6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID)
6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl
6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr,
hoplimit
1442 - Add pedit action with LAYERED_OP tcp set dport & sport
b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID)
cfcc - Add pedit action with LAYERED_OP tcp flags set
3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags
fields
f1c8 - Add pedit action with LAYERED_OP udp set dport & sport
d784 - Add pedit action with mixed RAW/LAYERED_OP #1
70ca - Add pedit action with mixed RAW/LAYERED_OP #2
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.

Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: Move fib_nh and fib6_nh to a common struct

First set of three with the end goal of enabling IPv6 gateways with IPv4
routes.

This set refactors ipv4 and ipv6 code to create init and release
helpers for each protocol and moving common elements to a fib_nh_common
struct.

v3
- split the reject setting into 2 with helper to the checks. This
  avoids changing cfg->fc_flags in fib6_nh_init

v2
- addressed Ido's comments: cleanup on failure path in nh_init helpers,
  ordering in fib6_nh_release, and removal of RTF_GATEWAY from fib6_info
  uses in mlxsw
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With fib_nh_common in place, move common initialization and release
code into helpers used by both ipv4 and ipv6. For the moment, the init
is just the lwt encap and the release is both the netdev reference and
the the lwt state reference. More will be added later.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add fib_nh_common struct with common nexthop attributes. Convert
fib_nh and fib6_nh to use it. Use macros to move existing
fib_nh_* references to the new nh_common.nhc_*.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.

Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename fib_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, oif, gateway, flags, scope, lwtstate,
nh_weight and nh_upper_bound are common with all nexthop definitions.
In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really
long lines.

Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rt6_add_nexthop and rt6_nexthop_info only need the fib6_info for the
gateway flag and the nexthop weight, and the presence of a gateway is now
per-nexthop. Update the signatures to take a fib6_nh and nexthop weight
and better align with the ipv4 versions.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib6_ignore_linkdown takes a fib6_info but only looks at the net_device
and its IPv6 config. Change it to take a net_device over a fib6_info as
its input argument.

In addition, move it to a header file to make the check inline and usable
later with IPv4 code without going through the ipv6 stub, and rename to
ip6_ignore_linkdown since it is only checking the setting based on the
ipv6 struct on a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new
fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to
the new flag. For IPv6 address the flag is cheaper than checking that
nh_gw is non-0 like IPv4 does.

While this increases fib6_nh by 8-bytes, the effective allocation size of
a fib6_info is unchanged. The 8 bytes is recovered later with a
fib_nh_common change.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the fib6_nh cleanup code to a new helper, fib6_nh_release.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to IPv4, consolidate the fib6_nh initialization into a helper.
As a new standalone function, add a cleanup path to put lwtstate on
error.

To avoid modifying fib6_config flags, move the reject check to a helper
that is invoked once by fib6_nh_init to reset the device and then
again in ip6_route_info_create to set the fib6_flags.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the fib_nh cleanup code from free_fib_info_rcu into a new helper,
fib_nh_release. Move classid accounting into fib_nh_release which is
called per fib_nh to make accounting symmetrical with fib_nh_init.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consolidate the fib_nh initialization which is duplicated between
fib_create_info for single path and fib_get_nhs for multipath.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in_dev lookup followed by IN_DEV_IGNORE_ROUTES_WITH_LINKDOWN check
is called in several places, some with the rcu lock and others with the
rtnl held.

Move the check to a helper similar to what IPv6 has. Since the helper
can be invoked from either context use rcu_dereference_rtnl to
dereference ip_ptr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define fib_get_nhs to return EINVAL when CONFIG_IP_ROUTE_MULTIPATH is
not enabled and remove the ifdef check for CONFIG_IP_ROUTE_MULTIPATH
in fib_create_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: forwarding: Add new test cases

This patchset mainly adds new forwarding test cases and performs small
changes in existing infrastructure.

Patches #1-#3 add new test cases for multicast RPF check, PCP and VLAN
matching using flower and tc VLAN modify action.

The rest of the patches are from Petr who says:

In patches #4 and #5, devlink_lib.sh is fixed to first not cause double
inclusion of lib.sh, and then to deduce the device name in a simpler way.

In patch #6, helpers for dealing with shared buffer configuration are
added to devlink_lib.sh.

In patch #7, MC-awareness test is fixed to configure shared buffers
explicitly.

In patch #8, several helpers are extracted from the MC-awareness test
and put into a new mlxsw-specific library, qos_lib.sh.

In patch #9, a new test is added which checks configuration of
strictly-prioritized streams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when strict priority is configured on a system, the
higher-priority traffic does actually win all the available bandwidth.
The test uses a similar approach to qos_mc_aware.sh to run and account
the traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract reusable code from qos_mc_aware.sh and put into a new library.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test runs two streams of traffic from two independent ports to
create congestion on one egress port. It is necessary to configure the
shared buffer thresholds correctly, to make sure that there is traffic
from both streams in the shared buffer. Only then can the test actually
test prioritization among these streams.

Without this configuration, it is possible, that one of the streams
takes all of port-pool quota, and the other stream is not even admitted,
thus invalidating the result.

On Spectrum-1, this is not a problem, because MC traffic uses a separate
pool. But for Spectrum-2, MC and UC share the same pool, and the correct
configuration is important.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Construct a basic topology consisting of two hosts connected using a
VLAN-aware bridge. Put each port in a different VLAN and test that ping
fails.

Add ingress and egress filters with a VLAN modify action and test that
ping passes.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send packets with VLAN and PCP set and check that TC flower filters can
match on these keys.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case a packet is routed using a multicast route whose specified
ingress interface does not match the interface from which the packet was
received, the packet is dropped.

Add IPv4 and IPv6 test cases for above mentioned scenario.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some PHYs will use the 2500BaseX PHY_INTERFACE_MODE when being linked
with a partner using 2.5GBaseT.

Since we can't autonegotiate this speed between the MAC and the PHY, we
need to have the proper comphy support enabled, to make sure we can
safely advertise 2.5G and 1G in BaseT and be able to switch between both
corresponding PHY interface modes. This is now possible since comphy
support was added to this driver.

This commit adds the 2500BaseT mode to the list of supported modes when
using 2500BaseX, and was tested on a setup with an Armada385 and a
88E2010 PHY, both with and without the comphy node in the DT.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for fine-grain timeout support to conntrack action.
The new OVS_CT_ATTR_TIMEOUT attribute of the conntrack action
specifies a timeout to be associated with this connection.
If no timeout is specified, it acts as is, that is the default
timeout for the connection will be automatically applied.

Example usage:
$ nfct timeout add timeout_1 inet tcp syn_sent 100 established 200
$ ovs-ofctl add-flow br0 in_port=1,ip,tcp,action=ct(commit,timeout=timeout_1)

CC: Pravin Shelar <pshelar@ovn.org>
CC: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch exports nf_ct_set_timeout() and nf_ct_destroy_timeout().
The two functions are derived from xt_ct_destroy_timeout() and
xt_ct_set_timeout() in xt_CT.c, and moved to nf_conntrack_timeout.c
without any functional change.
It would be useful for other users (i.e. OVS) that utilizes the
finer-grain conntrack timeout feature.

CC: Pablo Neira Ayuso <pablo@netfilter.org>
CC: Pravin Shelar <pshelar@ovn.org>
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2019-03-28

please apply the following patchset to net-next. This reworks the control
IO code in qeth so that we no longer need to poll for cmd completion,
and refactors the IDX setup code to also use this improved IO path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>