kvm_x86_ops->test_posted_interrupt() returns true/false depending
whether 'vector' is set.

Next patch makes use of this interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In most cases calling hwapic_isr_update(), we always check if
kvm_apic_vid_enabled() == 1, but actually,
kvm_apic_vid_enabled()
    -> kvm_x86_ops->vm_has_apicv()
        -> vmx_vm_has_apicv() or '0' in svm case
            -> return enable_apicv && irqchip_in_kernel(kvm)

So its a little cost to recall vmx_vm_has_apicv() inside
hwapic_isr_update(), here just NULL out hwapic_isr_update() in
case of !enable_apicv inside hardware_setup() then make all
related stuffs follow this. Note we don't check this under that
condition of irqchip_in_kernel() since we should make sure
definitely any caller don't work  without in-kernel irqchip.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Remove FIXME comments about needing fault addresses to be returned.  These
are propaagated from walk_addr_generic to gva_to_gpa and from there to
ops->read_std and ops->write_std.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

When generating #PF VM-exit, check equality:
(PFEC & PFEC_MASK) == PFEC_MATCH
If there is equality, the 14 bit of exception bitmap is used to take decision
about generating #PF VM-exit. If there is inequality, inverted 14 bit is used.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This patch improve checks required by Intel Software Developer Manual.
 - SMM MSRs are not allowed.
 - microcode MSRs are not allowed.
 - check x2apic MSRs only when LAPIC is in x2apic mode.
 - MSR switch areas must be aligned to 16 bytes.
 - address of first and last byte in MSR switch areas should not set any bits
   beyond the processor's physical-address width.

Also it adds warning messages on failures during MSR switch. These messages
are useful for people who debug their VMMs in nVMX.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull powerpc fixes from Michael Ellerman:

 - Wire up sys_execveat(). Tested on 32 & 64 bit.

 - Fix for kdump on LE systems with cpus hot unplugged.

 - Revert Anton's fix for "kernel BUG at kernel/smpboot.c:134!", this
   broke other platforms, we'll do a proper fix for 3.20.

* tag 'powerpc-3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  Revert "powerpc: Secondary CPUs must set cpu_callin_map after setting active and online"
  powerpc/kdump: Ignore failure in enabling big endian exception during crash
  powerpc: Wire up sys_execveat() syscall

Pull ia64 fixlet from Tony Luck:
 "Add execveat syscall"

* tag 'please-pull-syscall' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Enable execveat syscall for ia64

See commit 51f39a1f
    syscalls: implement execveat() system call
Signed-off-by: Tony Luck <tony.luck@intel.com>

Pull UML fixes from Richard Weinberger:
 "Two fixes for UML regressions. Nothing exciting"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  x86, um: actually mark system call tables readonly
  um: Skip futex_atomic_cmpxchg_inatomic() test

Commit 9fc2105a ("ARM: 7830/1: delay: don't bother reporting
bogomips in /proc/cpuinfo") breaks audio in python, and probably
elsewhere, with message

  FATAL: cannot locate cpu MHz in /proc/cpuinfo

I'm not the first one to hit it, see for example

  https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/
  https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1

Reading original changelog, I have to say "Stop breaking working setups.
You know who you are!".
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit a074335a ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.

Before:

$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
                 U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size

After:

$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
                 U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size

Fixes: a074335a ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>

Pull SCSI fixes from James Bottomley:
 "This is a set of three fixes: one to correct an abort path thinko
  causing failures (and a panic) in USB on device misbehaviour, One to
  fix an out of order issue in the fnic driver and one to match discard
  expectations to qemu which otherwise cause Linux to behave badly as a
  guest"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  SCSI: fix regression in scsi_send_eh_cmnd()
  fnic: IOMMU Fault occurs when IO and abort IO is out of order
  sd: tweak discard heuristics to work around QEMU SCSI issue

Pull sound fixes from Takashi Iwai:
 "Nothing too exciting as a new year's start here: most of fixes are for
  ASoC, a boot crash fix on OMAP for deferred probe, a few driver
  specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
  fixes in kerneldoc comments for PCM"

* tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pcm: Fix kerneldoc for params_*() functions
  ASoC: rockchip: i2s: fix maxburst of dma data to 4
  ASoC: rockchip: i2s: fix error defination of transmit data level
  ASoC: Intel: correct the fixed free block allocation
  ASoC: rt5677: fixed rt5677_dsp_vad_put rt5677_dsp_vad_get panic
  ASoC: Intel: Fix BYTCR machine driver MODULE_ALIAS
  ASoC: Intel: Fix BYTCR firmware name
  ASoC: dwc: Iterate over all channels
  ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
  ASoC: Intel: Add I2C dependency to two new machines
  ASoC: dapm: Remove snd_soc_of_parse_audio_routing() due to deferred probe

Pull vhost cleanup and virtio bugfix
 "There's a single change here, fixing a vhost bug where vhost
  initialization fails due to used ring alignment check being too
  strict"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost: relax used address alignment
  virtio_ring: document alignment requirements

Pull audit fix from Paul Moore:
 "One audit patch to resolve a panic/oops when recording filenames in
  the audit log, see the mail archive link below.

  The fix isn't as nice as I would like, as it involves an allocate/copy
  of the filename, but it solves the problem and the overhead should
  only affect users who have configured audit rules involving file
  names.

  We'll revisit this issue with future kernels in an attempt to make
  this suck less, but in the meantime I think this fix should go into
  the next release of v3.19-rcX.

  [ https://marc.info/?t=141986927600001&r=1&w=2 ]"

* 'upstream' of git://git.infradead.org/users/pcmoore/audit:
  audit: create private file name copies when auditing inodes

This reverts commit 9d469d03.

It breaks the Chromebook Pixel touchpad (and touchscreen).
Reported-by: Dirk Hohndel <dirk@hohndel.org>
Bisected-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nick Dyer <nick.dyer@itdev.co.uk>
Cc: Benson Leung <bleung@chromium.org>
Cc: Yufeng Shen <miletus@chromium.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable@vger.kernel.org  # v3.16+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arch/nios2 fixes from Ley Foon Tan:

 - fix compilation error when enable CONFIG_PREEMPT

 - initialize cpuinfo.mmu variable supplied by the device tree

* tag 'nios2-fixes-v3.19-rc3' of git://git.rocketboards.org/linux-socfpga-next:
  nios2: Use preempt_schedule_irq
  nios2: Initialize cpuinfo.mmu

Pull crypto fix from Herbert Xu:
 "Fix a use-after-free crash in the user-space crypto API"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: af_alg - fix backlog handling

Follow aa0d5326 ("ia64: Use preempt_schedule_irq") and use
preempt_schedule_irq instead of enabling/disabling interrupts and
messing around with PREEMPT_ACTIVE in the nios2 low-level preemption
code ourselves. Also get rid of the now needless re-check for
TIF_NEED_RESCHED, preempt_schedule_irq will already take care of
rescheduling.

This also fixes the following build error when building with
CONFIG_PREEMPT:

arch/nios2/kernel/built-in.o: In function `need_resched':
arch/nios2/kernel/entry.S:374: undefined reference to `PREEMPT_ACTIVE'

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>

This patch initializes the mmu field of the cpuinfo structure to the
value supplied by the devicetree.
Signed-off-by: Walter Goossens <waltergoossens@home.nl>
Acked-by: Ley Foon Tan <lftan@altera.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "A very small set of fixes for 3.19, as everyone was out.

  The clocksource patch was something I missed for the merge window
  after the change that broke arm64 was merged through arm-soc.  The
  other two patches are a fix for an undetected merge problem in mvebu
  and a defconfig change to make some exynos boards work with the normal
  multi_v7_defconfig"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  Add USB_EHCI_EXYNOS to multi_v7_defconfig
  ARM: mvebu: Fix pinctrl configuration for Armada 370 DB
  clocksource: arch_timer: Only use the virtual counter (CNTVCT) on arm64

Pull fbdev fixes from Tomi Valkeinen:

 - Fix regression with Nokia N900 display

 - Fix crash on fbdev using freed __initdata logos

 - Fix fb_deferred_io_fsync() return value.

* tag 'fbdev-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  OMAPDSS: SDI: fix output port_num
  video/fbdev: fix defio's fsync
  video/logo: prevent use of logos after they have been freed
  OMAPDSS: pll: NULL dereference in error handling
  OMAPDSS: HDMI: remove double initializer entries

Pull input layer fixes from Dmitry Torokhov:
 "Fixes for v7 protocol for ALPS devices and few other driver fixes.

  Also users can request input events to be stamped with boot time
  timestamps, in addition to real and monotonic timestamps"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: hil_kbd - fix incorrect use of init_completion
  Input: alps - v7: document the v7 touchpad packet protocol
  Input: alps - v7: fix finger counting for > 2 fingers on clickpads
  Input: alps - v7: sometimes a single touch is reported in mt[1]
  Input: alps - v7: ignore new packets
  Input: evdev - add CLOCK_BOOTTIME support
  Input: psmouse - expose drift duration for IBM trackpoints
  Input: stmpe - bias keypad columns properly
  Input: stmpe - enforce device tree only mode
  mfd: stmpe: add pull up/down register offsets for STMPE
  Input: optimize events_per_packet count calculation
  Input: edt-ft5x06 - fixed a macro coding style issue
  Input: gpio_keys - replace timer and workqueue with delayed workqueue
  Input: gpio_keys - allow separating gpio and irq in device tree

This reverts commit 24a0aa21.

It's causing severe userspace breakage.  Namely, all the utilities from
wireless-utils which are relying on CONFIG_WEXT (which means tools like
'iwconfig', 'iwlist', etc) are not working anymore.  There is a 'iw'
utility in newer wireless-tools, which is supposed to be a replacement
for all the "deprecated" binaries, but it's far away from being
massively adopted.

Please see [1] for example of the userspace breakage this is causing.

In addition to that, Larry Finger reports [2] that this patch is also
causing ipw2200 driver being impossible to build.

To me this clearly shows that CONFIG_WEXT is far, far away from being
"deprecated enough" to be removed.

[1] http://thread.gmane.org/gmane.linux.kernel/1857010
[2] http://thread.gmane.org/gmane.linux.network/343688Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Fix double SKB free in bluetooth 6lowpan layer, from Jukka Rissanen.

 2) Fix receive checksum handling in enic driver, from Govindarajulu
    Varadarajan.

 3) Fix NAPI poll list corruption in virtio_net and caif_virtio, from
    Herbert Xu.  Also, add code to detect drivers that have this mistake
    in the future.

 4) Fix doorbell endianness handling in mlx4 driver, from Amir Vadai.

 5) Don't clobber IP6CB() before xfrm6_policy_check() is called in TCP
    input path,f rom Nicolas Dichtel.

 6) Fix MPLS action validation in openvswitch, from Pravin B Shelar.

 7) Fix double SKB free in vxlan driver, also from Pravin.

 8) When we scrub a packet, which happens when we are switching the
    context of the packet (namespace, etc.), we should reset the
    secmark.  From Thomas Graf.

 9) ->ndo_gso_check() needs to do more than return true/false, it also
    has to allow the driver to clear netdev feature bits in order for
    the caller to be able to proceed properly.  From Jesse Gross.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  genetlink: A genl_bind() to an out-of-range multicast group should not WARN().
  netlink/genetlink: pass network namespace to bind/unbind
  ne2k-pci: Add pci_disable_device in error handling
  bonding: change error message to debug message in __bond_release_one()
  genetlink: pass multicast bind/unbind to families
  netlink: call unbind when releasing socket
  netlink: update listeners directly when removing socket
  genetlink: pass only network namespace to genl_has_listeners()
  netlink: rename netlink_unbind() to netlink_undo_bind()
  net: Generalize ndo_gso_check to ndo_features_check
  net: incorrect use of init_completion fixup
  neigh: remove next ptr from struct neigh_table
  net: xilinx: Remove unnecessary temac_property in the driver
  net: phy: micrel: use generic config_init for KSZ8021/KSZ8031
  net/core: Handle csum for CHECKSUM_COMPLETE VXLAN forwarding
  openvswitch: fix odd_ptr_err.cocci warnings
  Bluetooth: Fix accepting connections when not using mgmt
  Bluetooth: Fix controller configuration with HCI_QUIRK_INVALID_BDADDR
  brcmfmac: Do not crash if platform data is not populated
  ipw2200: select CFG80211_WEXT
  ...

Merge tag 'linux-kselftest-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fix from Shuah Khan:
 "Fix exec test compile warnings"

* tag 'linux-kselftest-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/exec: Use %zu to format size_t

Commit ac61d195 (scsi: set correct completion code in
scsi_send_eh_cmnd()) introduced a bug.  It changed the stored return
value from a queuecommand call, but it didn't take into account that
the return value was used again later on.  This patch fixes the bug by
changing the later usage.

There is a big comment in the middle of scsi_send_eh_cmnd() which
does a good job of explaining how the routine works.  But it mentions
a "rtn = FAILURE" value that doesn't exist in the code.  This patch
adjusts the code to match the comment (I assume the comment is right
and the code is wrong).

This fixes Bugzilla #88341.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Tested-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Fixes: ac61d195Acked-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fix a copy and paste error in the kernel doc description for the params_*()
functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.19

A few fixes for v3.19, a few driver specifics and one core fix which
fixes a boot crash on OMAP if deferred probing kicks in due to
attempting to modify static data.

Currently we enable Exynos devices in the multi v7 defconfig, however, when
testing on my ODROID-U3, I noticed that USB was not working.  Enabling this
option causes USB to work, which enables networking support as well since the
ODROID-U3 has networking on the USB bus.

[arnd] Support for odroid-u3 was added in 3.10, so it would be nice to
backport this fix at least that far.
Signed-off-by: Steev Klimaszewski <steev@gentoo.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull "Fixes for 3.19" from Andrew Lunn:

Jason is taking a back seat this cycle and i'm doing all the patch
wrangling for mvebu.

* tag 'mvebu-fixes-3.19' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Fix pinctrl configuration for Armada 370 DB

Also update to Linux 3.19-rc1, which this was based on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Unfortunately, while commit 4a928436 ("audit: correctly record file
names with different path name types") fixed a problem where we were
not recording filenames, it created a new problem by attempting to use
these file names after they had been freed.  This patch resolves the
issue by creating a copy of the filename which the audit subsystem
frees after it is done with the string.

At some point it would be nice to resolve this issue with refcounts,
or something similar, instead of having to allocate/copy strings, but
that is almost surely beyond the scope of a -rcX patch so we'll defer
that for later.  On the plus side, only audit users should be impacted
by the string copying.
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Paul Moore <pmoore@redhat.com>

When I/O is aborted by mid-layer, fnic FW will complete the I/O before
completing the abort task. In some cases abort request is completed before
the I/O, which could lead to inconsistent driver and firmware states.
In this case firmware reset would clear the inconsistent state.
Signed-off-by: Anil Chintalapati <achintal@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Shah <hishah@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

7985090a changed the discard heuristics to give preference to the
WRITE SAME commands that (unlike UNMAP) guarantee deterministic results.

Ming Lei discovered that QEMU SCSI's WRITE SAME implementation
internally relied on limits that were only communicated for the UNMAP
case. And therefore discard commands backed by WRITE SAME would fail.

Tweak the heuristics so we still pick UNMAP in the LBPRZ=0 case and only
prefer the WRITE SAME variants if the device has the LBPRZ flag set.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

After the commit ef691ff4 (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.

Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

fb_deferred_io_fsync() returns the value of schedule_delayed_work() as
an error code, but schedule_delayed_work() does not return an error. It
returns true/false depending on whether the work was already queued.

Fix this by ignoring the return value of schedule_delayed_work().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org

Pull CIFS fixes from Steve French:
 "A set of three minor cifs fixes"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: make new inode cache when file type is different
  Fix signed/unsigned pointer warning
  Convert MessageID in smb2_hdr to LE