Macvlan device in passthru mode sets its lower device promiscuous mode
according to its MACVLAN_FLAG_NOPROMISC flag instead of synchronizing it to
its own promiscuity setting. However, macvlan_change_rx_flags() function
doesn't check the mode before propagating such changes to the lower device
which can cause net_device->promiscuity counter overflow as illustrated by
reproduction example [0] and resulting dmesg log [1]. Fix the issue by
first verifying the mode in macvlan_change_rx_flags() function before
propagating promiscuous mode change to the lower device.

[0]:
ip link add macvlan1 link enp8s0f0 type macvlan mode passthru
ip link set macvlan1 promisc on
ip l set dev macvlan1 up
ip link set macvlan1 promisc off
ip l set dev macvlan1 down
ip l set dev macvlan1 up

[1]:
[ 5156.281724] macvlan1: entered promiscuous mode
[ 5156.285467] mlx5_core 0000:08:00.0 enp8s0f0: entered promiscuous mode
[ 5156.287639] macvlan1: left promiscuous mode
[ 5156.288339] mlx5_core 0000:08:00.0 enp8s0f0: left promiscuous mode
[ 5156.290907] mlx5_core 0000:08:00.0 enp8s0f0: entered promiscuous mode
[ 5156.317197] mlx5_core 0000:08:00.0 enp8s0f0: promiscuity touches roof, set promiscuity failed. promiscuity feature of device might be broken.

Fixes: efdbd2b3 ("macvlan: Propagate promiscuity setting to lower devices.")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20231114175915.1649154-1-vladbu@nvidia.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

There is no hardware supporting ct helper offload. However, prior to this
patch, a flower filter with a helper in the ct action can be successfully
set into the HW, for example (eth1 is a bnxt NIC):

  # tc qdisc add dev eth1 ingress_block 22 ingress
  # tc filter add block 22 proto ip flower skip_sw ip_proto tcp \
    dst_port 21 ct_state -trk action ct helper ipv4-tcp-ftp
  # tc filter show dev eth1 ingress

    filter block 22 protocol ip pref 49152 flower chain 0 handle 0x1
      eth_type ipv4
      ip_proto tcp
      dst_port 21
      ct_state -trk
      skip_sw
      in_hw in_hw_count 1   <----
        action order 1: ct zone 0 helper ipv4-tcp-ftp pipe
         index 2 ref 1 bind 1
        used_hw_stats delayed

This might cause the flower filter not to work as expected in the HW.

This patch avoids this problem by simply returning -EOPNOTSUPP in
tcf_ct_offload_act_setup() to not allow to offload flows with a helper
in act_ct.

Fixes: a21b06e7 ("net: sched: add helper support in act_ct")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/f8685ec7702c4a448a1371a8b34b43217b583b9d.1699898008.git.lucien.xin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Saeed Mahameed says:

====================
This series provides bug fixes to mlx5 driver.
====================

Link: https://lore.kernel.org/r/20231114215846.5902-1-saeed@kernel.org/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Treat the operation as an error case when the return value is equivalent to
the size of the name buffer. Failed to write null terminator to the name
buffer, making the string malformed and should not be used. Provide a
string with only the firmware version when forming the string with the
board id fails. This logic for representors is identical to normal flow
with ethtool.

Without check, will trigger -Wformat-truncation with W=1.

    drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_rep_get_drvinfo':
    drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:78:31: warning: '%.16s' directive output may be truncated writing up to 16 bytes into a region of size between 13 and 22 [-Wformat-truncation=]
      78 |                  "%d.%d.%04d (%.16s)",
         |                               ^~~~~
    drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:77:9: note: 'snprintf' output between 12 and 37 bytes into a destination of size 32
      77 |         snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
         |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      78 |                  "%d.%d.%04d (%.16s)",
         |                  ~~~~~~~~~~~~~~~~~~~~~
      79 |                  fw_rev_maj(mdev), fw_rev_min(mdev),
         |                  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      80 |                  fw_rev_sub(mdev), mdev->board_id);
         |                  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fixes: cf83c8fd ("net/mlx5e: Add missing ethtool driver info for representors")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732cSigned-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-16-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Treat the operation as an error case when the return value is equivalent to
the size of the name buffer. Failed to write null terminator to the name
buffer, making the string malformed and should not be used. Provide a
string with only the firmware version when forming the string with the
board id fails.

Without check, will trigger -Wformat-truncation with W=1.

    drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c: In function 'mlx5e_ethtool_get_drvinfo':
    drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:49:31: warning: '%.16s' directive output may be truncated writing up to 16 bytes into a region of size between 13 and 22 [-Wformat-truncation=]
      49 |                  "%d.%d.%04d (%.16s)",
         |                               ^~~~~
    drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:48:9: note: 'snprintf' output between 12 and 37 bytes into a destination of size 32
      48 |         snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
         |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      49 |                  "%d.%d.%04d (%.16s)",
         |                  ~~~~~~~~~~~~~~~~~~~~~
      50 |                  fw_rev_maj(mdev), fw_rev_min(mdev), fw_rev_sub(mdev),
         |                  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      51 |                  mdev->board_id);
         |                  ~~~~~~~~~~~~~~~

Fixes: 84e11edb ("net/mlx5e: Show board id in ethtool driver information")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732cSigned-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

icosq_str size is unnecessarily too long, and it causes a build warning
-Wformat-truncation with W=1. Looking closely, It doesn't need to be 255B,
hence this patch reduces the size to 32B which should be more than enough
to host the string: "ICOSQ: 0x%x, ".

While here, add a missing space in the formatted string.

This fixes the following build warning:

$ KCFLAGS='-Wall -Werror'
$ make O=/tmp/kbuild/linux W=1 -s -j12 drivers/net/ethernet/mellanox/mlx5/core/

drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c: In function 'mlx5e_reporter_rx_timeout':
drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c:718:56:
error: ', CQ: 0x' directive output may be truncated writing 8 bytes into a region of size between 0 and 255 [-Werror=format-truncation=]
  718 |                  "RX timeout on channel: %d, %sRQ: 0x%x, CQ: 0x%x",
      |                                                        ^~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c:717:9: note: 'snprintf' output between 43 and 322 bytes into a destination of size 288
  717 |         snprintf(err_str, sizeof(err_str),
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  718 |                  "RX timeout on channel: %d, %sRQ: 0x%x, CQ: 0x%x",
      |                  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  719 |                  rq->ix, icosq_str, rq->rqn, rq->cq.mcq.cqn);
      |                  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fixes: 521f31af ("net/mlx5e: Allow RQ outside of channel context")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732cSigned-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-14-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Without increased buffer size, will trigger -Wformat-truncation with W=1
for the snprintf operation writing to the buffer.

    drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c: In function 'mlx5_irq_alloc':
    drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c:296:7: error: '@pci:' directive output may be truncated writing 5 bytes into a region of size between 1 and 32 [-Werror=format-truncation=]
      296 |    "%s@pci:%s", name, pci_name(dev->pdev));
          |       ^~~~~
    drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c:295:2: note: 'snprintf' output 6 or more bytes (assuming 37) into a destination of size 32
      295 |  snprintf(irq->name, MLX5_MAX_IRQ_NAME,
          |  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      296 |    "%s@pci:%s", name, pci_name(dev->pdev));
          |    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fixes: ada9f5d0 ("IB/mlx5: Fix eq names to display nicely in /proc/interrupts")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732cSigned-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-13-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Previously, mlx5e_ptp_poll_ts_cq would update the device doorbell with the
incremented consumer index after the relevant software counters in the
kernel were updated. In the mlx5e_sq_xmit_wqe context, this would lead to
either overrunning the device CQ or exceeding the expected software buffer
size in the device CQ if the device CQ size was greater than the software
buffer size. Update the relevant software counter only after updating the
device CQ consumer index in the port timestamping napi_poll context.

Log:
    mlx5_core 0000:08:00.0: cq_err_event_notifier:517:(pid 0): CQ error on CQN 0x487, syndrome 0x1
    mlx5_core 0000:08:00.0 eth2: mlx5e_cq_error_event: cqn=0x000487 event=0x04

Fixes: 1880bc4e ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-12-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ensure the skb is available in metadata mapping to skbs before tracking the
metadata index for detecting undelivered CQEs. If the metadata index is put
in the tracking list before putting the skb in the map, the metadata index
might be used for detecting undelivered CQEs before the relevant skb is
available in the map, which can lead to a null-ptr-deref.

Log:
    general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] SMP KASAN
    KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
    CPU: 0 PID: 1243 Comm: kworker/0:2 Not tainted 6.6.0-rc4+ #108
    Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
    Workqueue: events mlx5e_rx_dim_work [mlx5_core]
    RIP: 0010:mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core]
    Code: 8c 24 38 cc ff ff 4c 8d 3c c1 4c 89 f9 48 c1 e9 03 42 80 3c 31 00 0f 85 97 0f 00 00 4d 8b 3f 49 8d 7f 28 48 89 f9 48 c1 e9 03 <42> 80 3c 31 00 0f 85 8b 0f 00 00 49 8b 47 28 48 85 c0 0f 84 05 07
    RSP: 0018:ffff8884d3c09c88 EFLAGS: 00010206
    RAX: 0000000000000069 RBX: ffff8881160349d8 RCX: 0000000000000005
    RDX: ffffed10218f48cf RSI: 0000000000000004 RDI: 0000000000000028
    RBP: ffff888122707700 R08: 0000000000000001 R09: ffffed109a781383
    R10: 0000000000000003 R11: 0000000000000003 R12: ffff88810c7a7a40
    R13: ffff888122707700 R14: dffffc0000000000 R15: 0000000000000000
    FS:  0000000000000000(0000) GS:ffff8884d3c00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00007f4f878dd6e0 CR3: 000000014d108002 CR4: 0000000000370eb0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
    Call Trace:
    <IRQ>
    ? die_addr+0x3c/0xa0
    ? exc_general_protection+0x144/0x210
    ? asm_exc_general_protection+0x22/0x30
    ? mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core]
    ? mlx5e_ptp_napi_poll+0x8f6/0x2290 [mlx5_core]
    __napi_poll.constprop.0+0xa4/0x580
    net_rx_action+0x460/0xb80
    ? _raw_spin_unlock_irqrestore+0x32/0x60
    ? __napi_poll.constprop.0+0x580/0x580
    ? tasklet_action_common.isra.0+0x2ef/0x760
    __do_softirq+0x26c/0x827
    irq_exit_rcu+0xc2/0x100
    common_interrupt+0x7f/0xa0
    </IRQ>
    <TASK>
    asm_common_interrupt+0x22/0x40
    RIP: 0010:__kmem_cache_alloc_node+0xb/0x330
    Code: 41 5d 41 5e 41 5f c3 8b 44 24 14 8b 4c 24 10 09 c8 eb d5 e8 b7 43 ca 01 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 57 <41> 56 41 89 d6 41 55 41 89 f5 41 54 49 89 fc 53 48 83 e4 f0 48 83
    RSP: 0018:ffff88812c4079c0 EFLAGS: 00000246
    RAX: 1ffffffff083c7fe RBX: ffff888100042dc0 RCX: 0000000000000218
    RDX: 00000000ffffffff RSI: 0000000000000dc0 RDI: ffff888100042dc0
    RBP: ffff88812c4079c8 R08: ffffffffa0289f96 R09: ffffed1025880ea9
    R10: ffff888138839f80 R11: 0000000000000002 R12: 0000000000000dc0
    R13: 0000000000000100 R14: 000000000000008c R15: ffff8881271fc450
    ? cmd_exec+0x796/0x2200 [mlx5_core]
    kmalloc_trace+0x26/0xc0
    cmd_exec+0x796/0x2200 [mlx5_core]
    mlx5_cmd_do+0x22/0xc0 [mlx5_core]
    mlx5_cmd_exec+0x17/0x30 [mlx5_core]
    mlx5_core_modify_cq_moderation+0x139/0x1b0 [mlx5_core]
    ? mlx5_add_cq_to_tasklet+0x280/0x280 [mlx5_core]
    ? lockdep_set_lock_cmp_fn+0x190/0x190
    ? process_one_work+0x659/0x1220
    mlx5e_rx_dim_work+0x9d/0x100 [mlx5_core]
    process_one_work+0x730/0x1220
    ? lockdep_hardirqs_on_prepare+0x400/0x400
    ? max_active_store+0xf0/0xf0
    ? assign_work+0x168/0x240
    worker_thread+0x70f/0x12d0
    ? __kthread_parkme+0xd1/0x1d0
    ? process_one_work+0x1220/0x1220
    kthread+0x2d9/0x3b0
    ? kthread_complete_and_exit+0x20/0x20
    ret_from_fork+0x2d/0x70
    ? kthread_complete_and_exit+0x20/0x20
    ret_from_fork_asm+0x11/0x20
    </TASK>
    Modules linked in: xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_ib ib_uverbs ib_core zram zsmalloc mlx5_core fuse
    ---[ end trace 0000000000000000 ]---

Fixes: 3178308a ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-11-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When SQ is a port timestamping SQ for PTP, do not access tx flags of skb
after free-ing the skb. Free the skb only after all references that depend
on it have been handled in the dropped WQE path.

Fixes: 3178308a ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-10-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As IPSec packet offload in switchdev mode is not supported with LAG,
it's unnecessary to modify those sent-to-vport rules to the peer eswitch.

Fixes: c6c2bf5d ("net/mlx5e: Support IPsec packet offload for TX in switchdev mode")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-9-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Referenced commit addressed endianness issue in mlx5 pedit implementation
in ad hoc manner instead of systematically treating integer values
according to their types which left pedit fields of sizes not equal to 4
and where the bytes being modified are not least significant ones broken on
big endian machines since wrong bits will be consumed during parsing which
leads to following example error when applying pedit to source and
destination MAC addresses:

[Wed Oct 18 12:52:42 2023] mlx5_core 0001:00:00.1 p1v3_r: attempt to offload an unsupported field (cmd 0)
[Wed Oct 18 12:52:42 2023] mask: 00000000330c5b68: 00 00 00 00 ff ff 00 00 00 00 ff ff 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 0000000017d22fd9: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 000000008186d717: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 0000000029eb6149: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 000000007ed103e4: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 00000000db8101a6: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
[Wed Oct 18 12:52:42 2023] mask: 00000000ec3c08a9: 00 00 00 00 00 00 00 00 00 00 00 00              ............

Treat masks and values of pedit and filter match as network byte order,
refactor pointers to them to void pointers instead of confusing u32
pointers and only cast to pointer-to-integer when reading a value from
them. Treat pedit mlx5_fields->field_mask as host byte order according to
its type u32, change the constants in fields array accordingly.

Fixes: 82198d8b ("net/mlx5e: Fix endianness when calculating pedit mask first bit")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-8-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Follow up to the previous patch to fix the same issue for
mlx5e_tc_tun_update_header_ipv4{6} when mlx5_packet_reformat_alloc()
fails.

When mlx5_packet_reformat_alloc() fails, the encap_header allocated in
mlx5e_tc_tun_update_header_ipv4{6} will be released within it. However,
e->encap_header is already set to the previously freed encap_header
before mlx5_packet_reformat_alloc(). As a result, the later
mlx5e_encap_put() will free e->encap_header again, causing a double free
issue.

mlx5e_encap_put()
     --> mlx5e_encap_dealloc()
         --> kfree(e->encap_header)

This patch fix it by not setting e->encap_header until
mlx5_packet_reformat_alloc() success.

Fixes: a54e20b4 ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-7-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When mlx5_packet_reformat_alloc() fails, the encap_header allocated in
mlx5e_tc_tun_create_header_ipv4{6} will be released within it. However,
e->encap_header is already set to the previously freed encap_header
before mlx5_packet_reformat_alloc(). As a result, the later
mlx5e_encap_put() will free e->encap_header again, causing a double free
issue.

mlx5e_encap_put()
    --> mlx5e_encap_dealloc()
        --> kfree(e->encap_header)

This happens when cmd: MLX5_CMD_OP_ALLOC_PACKET_REFORMAT_CONTEXT fail.

This patch fix it by not setting e->encap_header until
mlx5_packet_reformat_alloc() success.

Fixes: d589e785 ("net/mlx5e: Allow concurrent creation of encap entries")
Reported-by: Cruz Zhao <cruzzhao@linux.alibaba.com>
Reported-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When running a phase adjustment operation, the free running clock should
not be modified at all. The phase control keyword is intended to trigger an
internal servo on the device that will converge to the provided delta. A
free running counter cannot implement phase adjustment.

Fixes: 8e11a68e ("net/mlx5: Add adjphase function to support hardware-only offset control")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-5-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current check isn't aware of old devices that don't have the
relevant FW capability. This patch allows multi destination FTE
in old cards, as it was before this check.

Fixes: f6f46e71 ("net/mlx5: DR, Add check for multi destination FTE")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-4-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Each EQ table maintains a cpumask of the already used CPUs that are mapped
to IRQs to ensure that each IRQ gets mapped to a unique CPU.

However, on IRQ release, the said cpumask is not updated by clearing the
CPU from the mask to allow future IRQ request, causing the following
error when a SF is reloaded after it has utilized all CPUs for its IRQs:

mlx5_irq_affinity_request:135:(pid 306010): Didn't find a matching IRQ.
err = -28

Thus, when releasing an IRQ, clear its mapped CPU from the used CPUs
mask, to prevent the case described above.

While at it, move the used cpumask update to the EQ layer as it is more
fitting and preserves symmetricity of the IRQ request/release API.

Fixes: a1772de7 ("net/mlx5: Refactor completion IRQ request/release API")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-3-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 95c337cc.
The revert is required due to the suspicion it cause some tests
fail and will be moved to further investigation.

Fixes: 95c337cc ("net/mlx5: DR, Supporting inline WQE when possible")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-2-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Alexei Starovoitov says:

====================
pull-request: bpf 2023-11-15

We've added 7 non-merge commits during the last 6 day(s) which contain
a total of 9 files changed, 200 insertions(+), 49 deletions(-).

The main changes are:

1) Do not allocate bpf specific percpu memory unconditionally, from Yonghong.

2) Fix precision backtracking instruction iteration, from Andrii.

3) Fix control flow graph checking, from Andrii.

4) Fix xskxceiver selftest build, from Anders.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Do not allocate percpu memory at init stage
  selftests/bpf: add more test cases for check_cfg()
  bpf: fix control-flow graph checking in privileged mode
  selftests/bpf: add edge case backtracking logic test
  bpf: fix precision backtracking instruction iteration
  bpf: handle ldimm64 properly in check_cfg()
  selftests: bpf: xskxceiver: ksft_print_msg: fix format type error
====================

Link: https://lore.kernel.org/r/20231115214949.48854-1-alexei.starovoitov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kirill Shutemov reported significant percpu memory consumption increase after
booting in 288-cpu VM ([1]) due to commit 41a5db8d ("bpf: Add support for
non-fix-size percpu mem allocation"). The percpu memory consumption is
increased from 111MB to 969MB. The number is from /proc/meminfo.

I tried to reproduce the issue with my local VM which at most supports upto
255 cpus. With 252 cpus, without the above commit, the percpu memory
consumption immediately after boot is 57MB while with the above commit the
percpu memory consumption is 231MB.

This is not good since so far percpu memory from bpf memory allocator is not
widely used yet. Let us change pre-allocation in init stage to on-demand
allocation when verifier detects there is a need of percpu memory for bpf
program. With this change, percpu memory consumption after boot can be reduced
signicantly.

  [1] https://lore.kernel.org/lkml/20231109154934.4saimljtqx625l3v@box.shutemov.name/

Fixes: 41a5db8d ("bpf: Add support for non-fix-size percpu mem allocation")
Reported-and-tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231111013928.948838-1-yonghong.song@linux.devSigned-off-by: Alexei Starovoitov <ast@kernel.org>

Cited commit removed the strscpy() call and kept the snprintf() only.

It is common to use 'dev->name' as the format string before a netdev is
registered, this results in 'res' and 'name' pointers being equal.
According to POSIX, if copying takes place between objects that overlap
as a result of a call to sprintf() or snprintf(), the results are
undefined.

Add back the strscpy() and use 'buf' as an intermediate buffer.

Fixes: 7ad17b04 ("net: trust the bitmap in __dev_alloc_name()")
Cc: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When moving the *-internal-delay-ps properties to only apply for RGMII
interface modes there where a typo in the text formatting.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 3780bb29.

The cited commit introduced unwanted behavior.

The intent for the commit was to be able to detect carrier loss/gain
for just the NIC connected to the BMC. The unwanted effect is a
carrier loss for auxiliary paths also causes the BMC to lose
carrier. The BMC never regains carrier despite the secondary NIC
regaining a link.

This change, when merged, needs to be backported to stable kernels.
5.4-stable, 5.10-stable, 5.15-stable, 6.1-stable, 6.5-stable

Fixes: 3780bb29 ("ncsi: Propagate carrier gain/loss events to the NCSI controller")
CC: stable@vger.kernel.org
Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matthieu Baerts says:

====================
mptcp: misc. fixes for v6.7

Here are a few fixes related to MPTCP:

- Patch 1 limits GSO max size to ~64K when MPTCP is being used due to a
  spec limit. 'gso_max_size' can exceed the max value supported by MPTCP
  since v5.19.

- Patch 2 fixes a possible NULL pointer dereference on close that can
  happen since v6.7-rc1.

- Patch 3 avoids sending a RM_ADDR when the corresponding address is no
  longer tracked locally. A regression for a fix backported to v5.19.

- Patch 4 adds a missing lock when changing the IP TOS with setsockopt().
  A fix for v5.17.

- Patch 5 fixes an expectation when running MPTCP Join selftest with the
  checksum option (-C). An issue present since v6.1.
====================

Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-0-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Running the mp_join selftest manually with the following command line:

  ./mptcp_join.sh -z -C

leads to some failures:

  002 fastclose server test
  # ...
  rtx                                 [fail] got 1 MP_RST[s] TX expected 0
  # ...
  rstrx                               [fail] got 1 MP_RST[s] RX expected 0

The problem is really in the wrong expectations for the RST checks
implied by the csum validation. Note that the same check is repeated
explicitly in the same test-case, with the correct expectation and
pass successfully.

Address the issue explicitly setting the correct expectation for
the failing checks.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 6bf41020 ("selftests: mptcp: update and extend fastclose test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-5-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The MPTCP implementation of the IP_TOS socket option uses the lockless
variant of the TOS manipulation helper and does not hold such lock at
the helper invocation time.

Add the required locking.

Fixes: ffcacff8 ("mptcp: Support for IP_TOS for MPTCP setsockopt()")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/457Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-4-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds the validity check for sending RM_ADDRs for userspace PM
in mptcp_pm_remove_addrs(), only send a RM_ADDR when the address is in the
anno_list or conn_list.

Fixes: 8b1c94da ("mptcp: only send RM_ADDR in nl_cmd_remove")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-3-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After the blamed commit below, the MPTCP release callback can
dereference the first subflow pointer via __mptcp_set_connected()
and send buffer auto-tuning. Such pointer is always expected to be
valid, except at socket destruction time, when the first subflow is
deleted and the pointer zeroed.

If the connect event is handled by the release callback while the
msk socket is finally released, MPTCP hits the following splat:

  general protection fault, probably for non-canonical address 0xdffffc00000000f2: 0000 [#1] PREEMPT SMP KASAN
  KASAN: null-ptr-deref in range [0x0000000000000790-0x0000000000000797]
  CPU: 1 PID: 26719 Comm: syz-executor.2 Not tainted 6.6.0-syzkaller-10102-gff269e2c #0
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/09/2023
  RIP: 0010:mptcp_subflow_ctx net/mptcp/protocol.h:542 [inline]
  RIP: 0010:__mptcp_propagate_sndbuf net/mptcp/protocol.h:813 [inline]
  RIP: 0010:__mptcp_set_connected+0x57/0x3e0 net/mptcp/subflow.c:424
  RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff8a62323c
  RDX: 00000000000000f2 RSI: ffffffff8a630116 RDI: 0000000000000790
  RBP: ffff88803334b100 R08: 0000000000000001 R09: 0000000000000000
  R10: 0000000000000001 R11: 0000000000000034 R12: ffff88803334b198
  R13: ffff888054f0b018 R14: 0000000000000000 R15: ffff88803334b100
  FS:  0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007fbcb4f75198 CR3: 000000006afb5000 CR4: 00000000003506f0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   <TASK>
   mptcp_release_cb+0xa2c/0xc40 net/mptcp/protocol.c:3405
   release_sock+0xba/0x1f0 net/core/sock.c:3537
   mptcp_close+0x32/0xf0 net/mptcp/protocol.c:3084
   inet_release+0x132/0x270 net/ipv4/af_inet.c:433
   inet6_release+0x4f/0x70 net/ipv6/af_inet6.c:485
   __sock_release+0xae/0x260 net/socket.c:659
   sock_close+0x1c/0x20 net/socket.c:1419
   __fput+0x270/0xbb0 fs/file_table.c:394
   task_work_run+0x14d/0x240 kernel/task_work.c:180
   exit_task_work include/linux/task_work.h:38 [inline]
   do_exit+0xa92/0x2a20 kernel/exit.c:876
   do_group_exit+0xd4/0x2a0 kernel/exit.c:1026
   get_signal+0x23ba/0x2790 kernel/signal.c:2900
   arch_do_signal_or_restart+0x90/0x7f0 arch/x86/kernel/signal.c:309
   exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
   exit_to_user_mode_prepare+0x11f/0x240 kernel/entry/common.c:204
   __syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
   syscall_exit_to_user_mode+0x1d/0x60 kernel/entry/common.c:296
   do_syscall_64+0x4b/0x110 arch/x86/entry/common.c:88
   entry_SYSCALL_64_after_hwframe+0x63/0x6b
  RIP: 0033:0x7fb515e7cae9
  Code: Unable to access opcode bytes at 0x7fb515e7cabf.
  RSP: 002b:00007fb516c560c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
  RAX: 000000000000003c RBX: 00007fb515f9c120 RCX: 00007fb515e7cae9
  RDX: 0000000000000000 RSI: 0000000020000140 RDI: 0000000000000006
  RBP: 00007fb515ec847a R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
  R13: 000000000000006e R14: 00007fb515f9c120 R15: 00007ffc631eb968
   </TASK>

To avoid sparkling unneeded conditionals, address the issue explicitly
checking msk->first only in the critical place.

Fixes: 8005184f ("mptcp: refactor sndbuf auto-tuning")
Cc: stable@vger.kernel.org
Reported-by: <syzbot+9dfbaedb6e6baca57a32@syzkaller.appspotmail.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/454Reported-by: Eric Dumazet <edumazet@google.com>
Closes: https://lore.kernel.org/netdev/CANn89iLZUA6S2a=K8GObnS62KK6Jt4B7PsAs7meMFooM8xaTgw@mail.gmail.com/Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-2-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After the blamed commit below, the TCP sockets (and the MPTCP subflows)
can build egress packets larger than 64K. That exceeds the maximum DSS
data size, the length being misrepresent on the wire and the stream being
corrupted, as later observed on the receiver:

  WARNING: CPU: 0 PID: 9696 at net/mptcp/protocol.c:705 __mptcp_move_skbs_from_subflow+0x2604/0x26e0
  CPU: 0 PID: 9696 Comm: syz-executor.7 Not tainted 6.6.0-rc5-gcd8bdf563d46 #45
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
  netlink: 8 bytes leftover after parsing attributes in process `syz-executor.4'.
  RIP: 0010:__mptcp_move_skbs_from_subflow+0x2604/0x26e0 net/mptcp/protocol.c:705
  RSP: 0018:ffffc90000006e80 EFLAGS: 00010246
  RAX: ffffffff83e9f674 RBX: ffff88802f45d870 RCX: ffff888102ad0000
  netlink: 8 bytes leftover after parsing attributes in process `syz-executor.4'.
  RDX: 0000000080000303 RSI: 0000000000013908 RDI: 0000000000003908
  RBP: ffffc90000007110 R08: ffffffff83e9e078 R09: 1ffff1100e548c8a
  R10: dffffc0000000000 R11: ffffed100e548c8b R12: 0000000000013908
  R13: dffffc0000000000 R14: 0000000000003908 R15: 000000000031cf29
  FS:  00007f239c47e700(0000) GS:ffff88811b200000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f239c45cd78 CR3: 000000006a66c006 CR4: 0000000000770ef0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600
  PKRU: 55555554
  Call Trace:
   <IRQ>
   mptcp_data_ready+0x263/0xac0 net/mptcp/protocol.c:819
   subflow_data_ready+0x268/0x6d0 net/mptcp/subflow.c:1409
   tcp_data_queue+0x21a1/0x7a60 net/ipv4/tcp_input.c:5151
   tcp_rcv_established+0x950/0x1d90 net/ipv4/tcp_input.c:6098
   tcp_v6_do_rcv+0x554/0x12f0 net/ipv6/tcp_ipv6.c:1483
   tcp_v6_rcv+0x2e26/0x3810 net/ipv6/tcp_ipv6.c:1749
   ip6_protocol_deliver_rcu+0xd6b/0x1ae0 net/ipv6/ip6_input.c:438
   ip6_input+0x1c5/0x470 net/ipv6/ip6_input.c:483
   ipv6_rcv+0xef/0x2c0 include/linux/netfilter.h:304
   __netif_receive_skb+0x1ea/0x6a0 net/core/dev.c:5532
   process_backlog+0x353/0x660 net/core/dev.c:5974
   __napi_poll+0xc6/0x5a0 net/core/dev.c:6536
   net_rx_action+0x6a0/0xfd0 net/core/dev.c:6603
   __do_softirq+0x184/0x524 kernel/softirq.c:553
   do_softirq+0xdd/0x130 kernel/softirq.c:454

Address the issue explicitly bounding the maximum GSO size to what MPTCP
actually allows.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/450
Fixes: 7c4e983c ("net: allow gso_max_size to exceed 65536")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-1-7b9cd6a7b7f4@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Netpoll will explicilty pass the polling call with a budget of 0 to
indicate it's clearing the Tx path only. For the gve_rx_poll and
gve_xdp_poll, they were mistakenly taking the 0 budget as the indication
to do all the work. Add check to avoid the rx path and xdp path being
called when budget is 0. And also avoid napi_complete_done being called
when budget is 0 for netpoll.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Link: https://lore.kernel.org/r/20231114004144.2022268-1-ziweixiao@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-11-13 (ice)

This series contains updates to ice driver only.

Arkadiusz ensures the device is initialized with valid lock status
value. He also removes range checking of dpll priority to allow firmware
to process the request; supported values are firmware dependent.
Finally, he removes setting of can change capability for pins that
cannot be changed.

Dan restores ability to load a package which doesn't contain a signature
segment.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: fix DDP package download for packages without signature segment
  ice: dpll: fix output pin capabilities
  ice: dpll: fix check for dpll input priority range
  ice: dpll: fix initial lock status of dpll
====================

Link: https://lore.kernel.org/r/20231113230551.548489-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Shannon Nelson says:

====================
pds_core: fix irq index bug and compiler warnings

The first patch fixes a bug in our interrupt masking where we used the
wrong index.  The second patch addresses a couple of kernel test robot
string truncation warnings.
====================

Link: https://lore.kernel.org/r/20231113183257.71110-1-shannon.nelson@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Our friendly kernel test robot pointed out a couple of potential
string truncation issues.  None of which were we worried about,
but can be relatively easily fixed to quiet the complaints.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310211736.66syyDpp-lkp@intel.com/
Fixes: 45d76f49 ("pds_core: set up device and adminq")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20231113183257.71110-3-shannon.nelson@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the qcq's interrupt index, not the irq number, to mask
the interrupt.  Since the irq number can be out of range from
the number of possible interrupts, we can end up accessing
and potentially scribbling on out-of-range and/or unmapped
memory, making the kernel angry.

    [ 3116.039364] BUG: unable to handle page fault for address: ffffbeea1c3edf84
    [ 3116.047059] #PF: supervisor write access in kernel mode
    [ 3116.052895] #PF: error_code(0x0002) - not-present page
    [ 3116.058636] PGD 100000067 P4D 100000067 PUD 1001f2067 PMD 10f82e067 PTE 0
    [ 3116.066221] Oops: 0002 [#1] SMP NOPTI
    [ 3116.092948] RIP: 0010:iowrite32+0x9/0x76
    [ 3116.190452] Call Trace:
    [ 3116.193185]  <IRQ>
    [ 3116.195430]  ? show_trace_log_lvl+0x1d6/0x2f9
    [ 3116.200298]  ? show_trace_log_lvl+0x1d6/0x2f9
    [ 3116.205166]  ? pdsc_adminq_isr+0x43/0x55 [pds_core]
    [ 3116.210618]  ? __die_body.cold+0x8/0xa
    [ 3116.214806]  ? page_fault_oops+0x16d/0x1ac
    [ 3116.219382]  ? exc_page_fault+0xbe/0x13b
    [ 3116.223764]  ? asm_exc_page_fault+0x22/0x27
    [ 3116.228440]  ? iowrite32+0x9/0x76
    [ 3116.232143]  pdsc_adminq_isr+0x43/0x55 [pds_core]
    [ 3116.237627]  __handle_irq_event_percpu+0x3a/0x184
    [ 3116.243088]  handle_irq_event+0x57/0xb0
    [ 3116.247575]  handle_edge_irq+0x87/0x225
    [ 3116.252062]  __common_interrupt+0x3e/0xbc
    [ 3116.256740]  common_interrupt+0x7b/0x98
    [ 3116.261216]  </IRQ>
    [ 3116.263745]  <TASK>
    [ 3116.266268]  asm_common_interrupt+0x22/0x27
Reported-by: Joao Martins <joao.m.martins@oracle.com>
Fixes: 01ba61b5 ("pds_core: Add adminq processing and commands")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20231113183257.71110-2-shannon.nelson@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tg3_tso_bug() drops a packet if it cannot be segmented for any reason.
The number of discarded frames should be incremented accordingly.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-2-alexey.pakhunov@spacex.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This change moves [rt]x_dropped counters to tg3_napi so that they can be
updated by a single writer, race-free.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-1-alexey.pakhunov@spacex.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

dma_rx_size can be set as low as 64. Rx budget might be higher than
that. Make sure to not overrun allocated rx buffers when budget is
larger.

Leave one descriptor unused to avoid wrap around of 'dirty_rx' vs
'cur_rx'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 47dd7a54 ("net: add support for STMicroelectronics Ethernet controllers.")
Link: https://lore.kernel.org/r/d95413e44c97d4692e72cec13a75f894abeb6998.1699897370.git.baruch@tkos.co.ilSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The while loop condition verifies 'count < limit'. Neither value change
before the 'count >= limit' check. As is this check is dead code. But
code inspection reveals a code path that modifies 'count' and then goto
'drain_data' and back to 'read_again'. So there is a need to verify
count value sanity after 'read_again'.

Move 'read_again' up to fix the count limit check.

Fixes: ec222003 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/d9486296c3b6b12ab3a0515fcd47d56447a07bfc.1699897370.git.baruch@tkos.co.ilSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported the following crash [1]

After releasing unix socket lock, u->oob_skb can be changed
by another thread. We must temporarily increase skb refcount
to make sure this other thread will not free the skb under us.

[1]

BUG: KASAN: slab-use-after-free in unix_stream_read_actor+0xa7/0xc0 net/unix/af_unix.c:2866
Read of size 4 at addr ffff88801f3b9cc4 by task syz-executor107/5297

CPU: 1 PID: 5297 Comm: syz-executor107 Not tainted 6.6.0-syzkaller-15910-gb8e3a87a #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/09/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x1b0 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:364 [inline]
print_report+0xc4/0x620 mm/kasan/report.c:475
kasan_report+0xda/0x110 mm/kasan/report.c:588
unix_stream_read_actor+0xa7/0xc0 net/unix/af_unix.c:2866
unix_stream_recv_urg net/unix/af_unix.c:2587 [inline]
unix_stream_read_generic+0x19a5/0x2480 net/unix/af_unix.c:2666
unix_stream_recvmsg+0x189/0x1b0 net/unix/af_unix.c:2903
sock_recvmsg_nosec net/socket.c:1044 [inline]
sock_recvmsg+0xe2/0x170 net/socket.c:1066
____sys_recvmsg+0x21f/0x5c0 net/socket.c:2803
___sys_recvmsg+0x115/0x1a0 net/socket.c:2845
__sys_recvmsg+0x114/0x1e0 net/socket.c:2875
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
RIP: 0033:0x7fc67492c559
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fc6748ab228 EFLAGS: 00000246 ORIG_RAX: 000000000000002f
RAX: ffffffffffffffda RBX: 000000000000001c RCX: 00007fc67492c559
RDX: 0000000040010083 RSI: 0000000020000140 RDI: 0000000000000004
RBP: 00007fc6749b6348 R08: 00007fc6748ab6c0 R09: 00007fc6748ab6c0
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc6749b6340
R13: 00007fc6749b634c R14: 00007ffe9fac52a0 R15: 00007ffe9fac5388
</TASK>

Allocated by task 5295:
kasan_save_stack+0x33/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
__kasan_slab_alloc+0x81/0x90 mm/kasan/common.c:328
kasan_slab_alloc include/linux/kasan.h:188 [inline]
slab_post_alloc_hook mm/slab.h:763 [inline]
slab_alloc_node mm/slub.c:3478 [inline]
kmem_cache_alloc_node+0x180/0x3c0 mm/slub.c:3523
__alloc_skb+0x287/0x330 net/core/skbuff.c:641
alloc_skb include/linux/skbuff.h:1286 [inline]
alloc_skb_with_frags+0xe4/0x710 net/core/skbuff.c:6331
sock_alloc_send_pskb+0x7e4/0x970 net/core/sock.c:2780
sock_alloc_send_skb include/net/sock.h:1884 [inline]
queue_oob net/unix/af_unix.c:2147 [inline]
unix_stream_sendmsg+0xb5f/0x10a0 net/unix/af_unix.c:2301
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
____sys_sendmsg+0x6ac/0x940 net/socket.c:2584
___sys_sendmsg+0x135/0x1d0 net/socket.c:2638
__sys_sendmsg+0x117/0x1e0 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Freed by task 5295:
kasan_save_stack+0x33/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2b/0x40 mm/kasan/generic.c:522
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free+0x15b/0x1b0 mm/kasan/common.c:200
kasan_slab_free include/linux/kasan.h:164 [inline]
slab_free_hook mm/slub.c:1800 [inline]
slab_free_freelist_hook+0x114/0x1e0 mm/slub.c:1826
slab_free mm/slub.c:3809 [inline]
kmem_cache_free+0xf8/0x340 mm/slub.c:3831
kfree_skbmem+0xef/0x1b0 net/core/skbuff.c:1015
__kfree_skb net/core/skbuff.c:1073 [inline]
consume_skb net/core/skbuff.c:1288 [inline]
consume_skb+0xdf/0x170 net/core/skbuff.c:1282
queue_oob net/unix/af_unix.c:2178 [inline]
unix_stream_sendmsg+0xd49/0x10a0 net/unix/af_unix.c:2301
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
____sys_sendmsg+0x6ac/0x940 net/socket.c:2584
___sys_sendmsg+0x135/0x1d0 net/socket.c:2638
__sys_sendmsg+0x117/0x1e0 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

The buggy address belongs to the object at ffff88801f3b9c80
which belongs to the cache skbuff_head_cache of size 240
The buggy address is located 68 bytes inside of
freed 240-byte region [ffff88801f3b9c80, ffff88801f3b9d70)

The buggy address belongs to the physical page:
page:ffffea00007cee40 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1f3b9
flags: 0xfff00000000800(slab|node=0|zone=1|lastcpupid=0x7ff)
page_type: 0xffffffff()
raw: 00fff00000000800 ffff888142a60640 dead000000000122 0000000000000000
raw: 0000000000000000 00000000000c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x12cc0(GFP_KERNEL|__GFP_NOWARN|__GFP_NORETRY), pid 5299, tgid 5283 (syz-executor107), ts 103803840339, free_ts 103600093431
set_page_owner include/linux/page_owner.h:31 [inline]
post_alloc_hook+0x2cf/0x340 mm/page_alloc.c:1537
prep_new_page mm/page_alloc.c:1544 [inline]
get_page_from_freelist+0xa25/0x36c0 mm/page_alloc.c:3312
__alloc_pages+0x1d0/0x4a0 mm/page_alloc.c:4568
alloc_pages_mpol+0x258/0x5f0 mm/mempolicy.c:2133
alloc_slab_page mm/slub.c:1870 [inline]
allocate_slab+0x251/0x380 mm/slub.c:2017
new_slab mm/slub.c:2070 [inline]
___slab_alloc+0x8c7/0x1580 mm/slub.c:3223
__slab_alloc.constprop.0+0x56/0xa0 mm/slub.c:3322
__slab_alloc_node mm/slub.c:3375 [inline]
slab_alloc_node mm/slub.c:3468 [inline]
kmem_cache_alloc_node+0x132/0x3c0 mm/slub.c:3523
__alloc_skb+0x287/0x330 net/core/skbuff.c:641
alloc_skb include/linux/skbuff.h:1286 [inline]
alloc_skb_with_frags+0xe4/0x710 net/core/skbuff.c:6331
sock_alloc_send_pskb+0x7e4/0x970 net/core/sock.c:2780
sock_alloc_send_skb include/net/sock.h:1884 [inline]
queue_oob net/unix/af_unix.c:2147 [inline]
unix_stream_sendmsg+0xb5f/0x10a0 net/unix/af_unix.c:2301
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
____sys_sendmsg+0x6ac/0x940 net/socket.c:2584
___sys_sendmsg+0x135/0x1d0 net/socket.c:2638
__sys_sendmsg+0x117/0x1e0 net/socket.c:2667
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1137 [inline]
free_unref_page_prepare+0x4f8/0xa90 mm/page_alloc.c:2347
free_unref_page+0x33/0x3b0 mm/page_alloc.c:2487
__unfreeze_partials+0x21d/0x240 mm/slub.c:2655
qlink_free mm/kasan/quarantine.c:168 [inline]
qlist_free_all+0x6a/0x170 mm/kasan/quarantine.c:187
kasan_quarantine_reduce+0x18e/0x1d0 mm/kasan/quarantine.c:294
__kasan_slab_alloc+0x65/0x90 mm/kasan/common.c:305
kasan_slab_alloc include/linux/kasan.h:188 [inline]
slab_post_alloc_hook mm/slab.h:763 [inline]
slab_alloc_node mm/slub.c:3478 [inline]
slab_alloc mm/slub.c:3486 [inline]
__kmem_cache_alloc_lru mm/slub.c:3493 [inline]
kmem_cache_alloc+0x15d/0x380 mm/slub.c:3502
vm_area_dup+0x21/0x2f0 kernel/fork.c:500
__split_vma+0x17d/0x1070 mm/mmap.c:2365
split_vma mm/mmap.c:2437 [inline]
vma_modify+0x25d/0x450 mm/mmap.c:2472
vma_modify_flags include/linux/mm.h:3271 [inline]
mprotect_fixup+0x228/0xc80 mm/mprotect.c:635
do_mprotect_pkey+0x852/0xd60 mm/mprotect.c:809
__do_sys_mprotect mm/mprotect.c:830 [inline]
__se_sys_mprotect mm/mprotect.c:827 [inline]
__x64_sys_mprotect+0x78/0xb0 mm/mprotect.c:827
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Memory state around the buggy address:
ffff88801f3b9b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88801f3b9c00: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc
>ffff88801f3b9c80: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88801f3b9d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc
ffff88801f3b9d80: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb

Fixes: 876c14ad ("af_unix: fix holding spinlock in oob handling")
Reported-and-tested-by: syzbot+7a2d546fa43e49315ed3@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rao Shoaib <rao.shoaib@oracle.com>
Reviewed-by: Rao shoaib <rao.shoaib@oracle.com>
Link: https://lore.kernel.org/r/20231113134938.168151-1-edumazet@google.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

ChunHao Lin says:

====================
r8169: fix DASH devices network lost issue

This series are used to fix network lost issue on systems that support
DASH. It has been tested on rtl8168ep and rtl8168fp.
====================

Link: https://lore.kernel.org/r/20231109173400.4573-1-hau@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>