Stephen Hemminger says:

====================
hv_netvsc: fix multicast flags and sync

This set of patches deals with the handling of multicast flags
and addresses in transparent VF mode. The recent set of patches
(in linux-net) had a couple of bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc driver can get repeated calls to netvsc_rx_mode during
network setup; each of these calls ends up scheduling the lower
layers to update tha packet filter. This update requires an
request/response to the host. So avoid doing this if we already
know that the correct packet filter value is set.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.

Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo:

====================
wireless-drivers fixes for 4.16

Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.

iwlwifi

* fix a bogus warning when freeing a TFD

* fix severe throughput problem with 9000 series

* fix for a bug that caused queue hangs in certain situations

* fix for an issue with IBSS

* fix an issue with rate-scaling in AP-mode

* fix Channel Switch Announcement (CSA) issues with count 0 and 1

* some firmware debugging fixes

* remov a wrong error message when removing keys

* fix a firmware sysassert most usually triggered in IBSS

* a couple of fixes on multicast queues

* a fix with CCMP 256

rtlwifi

* fix loss of signal for rtl8723be

brcmfmac

* add possibility to obtain firmware error

* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pretty minor: just SKB_GSO_TCP  -> SKB_GSO_TCPV4 and
                   SKB_GSO_TCP6 -> SKB_GSO_TCPV6.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The __send_and_alloc_skb() receives a skb ptr as a parameter but in
case it fails the skb is not valid:
- Send failed and released the skb internally.
- Allocation failed.

The current code tries to release the skb in case of failure which
causes redundant freeing.

Fixes: 9b00cf2d ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-03-08

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix various BPF helpers which adjust the skb and its GSO information
   with regards to SCTP GSO. The latter is a special case where gso_size
   is of value GSO_BY_FRAGS, so mangling that will end up corrupting
   the skb, thus bail out when seeing SCTP GSO packets, from Daniel(s).

2) Fix a compilation error in bpftool where BPF_FS_MAGIC is not defined
   due to too old kernel headers in the system, from Jiri.

3) Increase the number of x64 JIT passes in order to allow larger images
   to converge instead of punting them to interpreter or having them
   rejected when the interpreter is not built into the kernel, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).

One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with v4.16-rc1 we've been seeing a higher than usual number
of requests for the kernel to load networking modules, even on events
which shouldn't trigger a module load (e.g. ioctl(TCGETS)).  Stephen
Smalley suggested the problem may lie in commit 44c02a2c
("dev_ioctl(): move copyin/copyout to callers") which moves changes
the network dev_ioctl() function to always call dev_load(),
regardless of the requested ioctl.

This patch moves the dev_load() calls back into the individual ioctls
while preserving the rest of the original patch.
Reported-by: Dominick Grift <dac.override@gmail.com>
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.

Similar to a27fd7a8 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.

Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL,
therefore if DCCP socket is disconnected and dccp_sendmsg() is
called after it, it will cause a NULL pointer dereference in
dccp_write_xmit().

This crash and the reproducer was reported by syzbot. Looks like
it is reproduced if commit 69c64866 ("dccp: CVE-2017-8824:
use-after-free in DCCP code") is applied.

Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller found an issue caused by lack of sufficient checks
in l2tp_tunnel_create()

RAW sockets can not be considered as UDP ones for instance.

In another patch, we shall replace all pr_err() by less intrusive
pr_debug() so that syzkaller can find other bugs faster.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>

==================================================================
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
dst_release: dst:00000000d53d0d0f refcnt:-1
Write of size 1 at addr ffff8801d013b798 by task syz-executor3/6242

CPU: 1 PID: 6242 Comm: syz-executor3 Not tainted 4.16.0-rc2+ #253
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x24d lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report+0x23b/0x360 mm/kasan/report.c:412
 __asan_report_store1_noabort+0x17/0x20 mm/kasan/report.c:435
 setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
 l2tp_tunnel_create+0x1354/0x17f0 net/l2tp/l2tp_core.c:1596
 pppol2tp_connect+0x14b1/0x1dd0 net/l2tp/l2tp_ppp.c:707
 SYSC_connect+0x213/0x4a0 net/socket.c:1640
 SyS_connect+0x24/0x30 net/socket.c:1621
 do_syscall_64+0x280/0x940 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x42/0xb7

Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_evict_bucket() iterates global list, and
several tasks may call it in parallel. All of
them hash the same fq->list_evictor to different
lists, which leads to list corruption.

This patch makes fq be hashed to expired list
only if this has not been made yet by another
task. Since inet_frag_alloc() allocates fq
using kmem_cache_zalloc(), we may rely on
list_evictor is initially unhashed.

The problem seems to exist before async
pernet_operations, as there was possible to have
exit method to be executed in parallel with
inet_frags::frags_work, so I add two Fixes tags.
This also may go to stable.

Fixes: d1fe1944 "inet: frag: don't re-use chainlist for evictor"
Fixes: f84c6821 "net: Convert pernet_subsys, registered from inet_init()"
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:

Call trace:
  phy_detach+0x94/0x150
  phy_disconnect+0x40/0x50
  smsc911x_stop+0x104/0x128 [smsc911x]
  __dev_close_many+0xb4/0x138
  dev_close_many+0xbc/0x190
  rollback_registered_many+0x140/0x460
  rollback_registered+0x68/0xb0
  unregister_netdevice_queue+0x100/0x118
  unregister_netdev+0x28/0x38
  smsc911x_drv_remove+0x58/0x130 [smsc911x]
  platform_drv_remove+0x30/0x50
  device_release_driver_internal+0x15c/0x1f8
  driver_detach+0x54/0x98
  bus_remove_driver+0x64/0xe8
  driver_unregister+0x34/0x60
  platform_driver_unregister+0x20/0x30
  smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
  SyS_delete_module+0x1e8/0x238
  __sys_trace_return+0x0/0x4

This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()

To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.
Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, administrative MTU changes on a given netdevice are
not reflected on route exceptions for MTU-less routes, with a
set PMTU value, for that device:

 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a proto kernel src 2001:db8::a metric 256 pref medium
 # ping6 -c 1 -q -s10000 2001:db8::b > /dev/null
 # ip netns exec a ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium
 # ip link set dev vti_a mtu 3000
 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium
 # ip link set dev vti_a mtu 9000
 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium

The first issue is that since commit fb56be83 ("net-ipv6: on
device mtu change do not add mtu to mtu-less routes") we don't
call rt6_exceptions_update_pmtu() from rt6_mtu_change_route(),
which handles administrative MTU changes, if the regular route
is MTU-less.

However, PMTU exceptions should be always updated, as long as
RTAX_MTU is not locked. Keep the check for MTU-less main route,
as introduced by that commit, but, for exceptions,
call rt6_exceptions_update_pmtu() regardless of that check.

Once that is fixed, one problem remains: MTU changes are not
reflected if the new MTU is higher than the previous one,
because rt6_exceptions_update_pmtu() doesn't allow that. We
should instead allow PMTU increase if the old PMTU matches the
local MTU, as that implies that the old MTU was the lowest in the
path, and PMTU discovery might lead to different results.

The existing check in rt6_mtu_change_route() correctly took that
case into account (for regular routes only), so factor it out
and re-use it also in rt6_exceptions_update_pmtu().

While at it, fix comments style and grammar, and try to be a bit
more descriptive.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: fb56be83 ("net-ipv6: on device mtu change do not add mtu to mtu-less routes")
Fixes: f5bbe7ee ("ipv6: prepare rt6_mtu_change() for exception table")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).

An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.

The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.

In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.

Fixes: dbb799c3 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-03-05

This series contains fixes to e1000e only.

Benjamin Poirier provides all but one fix in this series, starting with
workaround for a VMWare e1000e emulation issue where ICR reads 0x0 on
the emulated device.  Partially reverted a previous commit dealing with
the "Other" interrupt throttling to avoid unforeseen fallout from these
changes that are not strictly necessary.  Restored the ICS write for
receive and transmit queue interrupts in the case that txq or rxq bits
were set in ICR and the Other interrupt handler read and cleared ICR
before the queue interrupt was raised.  Fixed an bug where interrupts
may be missed if ICR is read while INT_ASSERTED is not set, so avoid the
problem by setting all bits related to events that can trigger the Other
interrupt in IMS.  Fixed the return value for check_for_link() when
auto-negotiation is off.

Pierre-Yves Kerbrat fixes e1000e to use dma_zalloc_coherent() to make
sure the ring is memset to 0 to prevent the area from containing
garbage.

v2: added an additional e1000e fix to the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek reported a LOCKDEP issue occurring on 32bit host,
that we tracked down to the fact that usbnet could either
run from soft or hard irqs.

This patch adds u64_stats_update_begin_irqsave() and
u64_stats_update_end_irqrestore() helpers to solve this case.

[   17.768040] ================================
[   17.772239] WARNING: inconsistent lock state
[   17.776511] 4.16.0-rc3-next-20180227-00007-g876c53a7493c #453 Not tainted
[   17.783329] --------------------------------
[   17.787580] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[   17.793607] swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[   17.798751]  (&syncp->seq#5){?.-.}, at: [<9b22e5f0>]
asix_rx_fixup_internal+0x188/0x288
[   17.806790] {IN-HARDIRQ-W} state was registered at:
[   17.811677]   tx_complete+0x100/0x208
[   17.815319]   __usb_hcd_giveback_urb+0x60/0xf0
[   17.819770]   xhci_giveback_urb_in_irq+0xa8/0x240
[   17.824469]   xhci_td_cleanup+0xf4/0x16c
[   17.828367]   xhci_irq+0xe74/0x2240
[   17.831827]   usb_hcd_irq+0x24/0x38
[   17.835343]   __handle_irq_event_percpu+0x98/0x510
[   17.840111]   handle_irq_event_percpu+0x1c/0x58
[   17.844623]   handle_irq_event+0x38/0x5c
[   17.848519]   handle_fasteoi_irq+0xa4/0x138
[   17.852681]   generic_handle_irq+0x18/0x28
[   17.856760]   __handle_domain_irq+0x6c/0xe4
[   17.860941]   gic_handle_irq+0x54/0xa0
[   17.864666]   __irq_svc+0x70/0xb0
[   17.867964]   arch_cpu_idle+0x20/0x3c
[   17.871578]   arch_cpu_idle+0x20/0x3c
[   17.875190]   do_idle+0x144/0x218
[   17.878468]   cpu_startup_entry+0x18/0x1c
[   17.882454]   start_kernel+0x394/0x400
[   17.886177] irq event stamp: 161912
[   17.889616] hardirqs last  enabled at (161912): [<7bedfacf>]
__netdev_alloc_skb+0xcc/0x140
[   17.897893] hardirqs last disabled at (161911): [<d58261d0>]
__netdev_alloc_skb+0x94/0x140
[   17.904903] exynos5-hsi2c 12ca0000.i2c: tx timeout
[   17.906116] softirqs last  enabled at (161904): [<387102ff>]
irq_enter+0x78/0x80
[   17.906123] softirqs last disabled at (161905): [<cf4c628e>]
irq_exit+0x134/0x158
[   17.925722].
[   17.925722] other info that might help us debug this:
[   17.933435]  Possible unsafe locking scenario:
[   17.933435].
[   17.940331]        CPU0
[   17.942488]        ----
[   17.944894]   lock(&syncp->seq#5);
[   17.948274]   <Interrupt>
[   17.950847]     lock(&syncp->seq#5);
[   17.954386].
[   17.954386]  *** DEADLOCK ***
[   17.954386].
[   17.962422] no locks held by swapper/0/0.

Fixes: c8b5d129 ("net: usbnet: support 64bit stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we exceed current packets limit and we have more than one
segment in the list returned by skb_gso_segment(), netem drops
only the first one, skipping the rest, hence kmemleak reports:

unreferenced object 0xffff880b5d23b600 (size 1024):
  comm "softirq", pid 0, jiffies 4384527763 (age 2770.629s)
  hex dump (first 32 bytes):
    00 80 23 5d 0b 88 ff ff 00 00 00 00 00 00 00 00  ..#]............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000d8a19b9d>] __alloc_skb+0xc9/0x520
    [<000000001709b32f>] skb_segment+0x8c8/0x3710
    [<00000000c7b9bb88>] tcp_gso_segment+0x331/0x1830
    [<00000000c921cba1>] inet_gso_segment+0x476/0x1370
    [<000000008b762dd4>] skb_mac_gso_segment+0x1f9/0x510
    [<000000002182660a>] __skb_gso_segment+0x1dd/0x620
    [<00000000412651b9>] netem_enqueue+0x1536/0x2590 [sch_netem]
    [<0000000005d3b2a9>] __dev_queue_xmit+0x1167/0x2120
    [<00000000fc5f7327>] ip_finish_output2+0x998/0xf00
    [<00000000d309e9d3>] ip_output+0x1aa/0x2c0
    [<000000007ecbd3a4>] tcp_transmit_skb+0x18db/0x3670
    [<0000000042d2a45f>] tcp_write_xmit+0x4d4/0x58c0
    [<0000000056a44199>] tcp_tasklet_func+0x3d9/0x540
    [<0000000013d06d02>] tasklet_action+0x1ca/0x250
    [<00000000fcde0b8b>] __do_softirq+0x1b4/0x5a3
    [<00000000e7ed027c>] irq_exit+0x1e2/0x210

Fix it by adding the rest of the segments, if any, to skb 'to_free'
list. Add new __qdisc_drop_all() and qdisc_drop_all() functions
because they can be useful in the future if we need to drop segmented
GSO packets in other places.

Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2018-03-05

Here are a few more Bluetooth fixes for the 4.16 kernel:

 - btusb: reset/resume fixes for Yoga 920 and Dell OptiPlex 3060
 - Fix for missing encryption refresh with the Security Manager protocol
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

__dev_mc_add grabs an adress spinlock so use
atomic context in kmalloc.

/ # ifconfig eth0 inet 192.168.0.111
[   89.331622] BUG: sleeping function called from invalid context at mm/slab.h:420
[   89.339002] in_atomic(): 1, irqs_disabled(): 0, pid: 1035, name: ifconfig
[   89.345799] 2 locks held by ifconfig/1035:
[   89.349908]  #0:  (rtnl_mutex){+.+.}, at: [<(ptrval)>] devinet_ioctl+0xc0/0x8a0
[   89.357258]  #1:  (_xmit_ETHER){+...}, at: [<(ptrval)>] __dev_mc_add+0x28/0x80
[   89.364520] CPU: 1 PID: 1035 Comm: ifconfig Not tainted 4.16.0-rc3-dirty #8
[   89.371464] Call Trace:
[   89.373908] [e959db60] [c066f948] dump_stack+0xa4/0xfc (unreliable)
[   89.380177] [e959db80] [c00671d8] ___might_sleep+0x248/0x280
[   89.385833] [e959dba0] [c01aec34] kmem_cache_alloc_trace+0x174/0x320
[   89.392179] [e959dbd0] [c04ab920] dtsec_add_hash_mac_address+0x130/0x240
[   89.398874] [e959dc00] [c04a9d74] set_multi+0x174/0x1b0
[   89.404093] [e959dc30] [c04afb68] dpaa_set_rx_mode+0x68/0xe0
[   89.409745] [e959dc40] [c057baf8] __dev_mc_add+0x58/0x80
[   89.415052] [e959dc60] [c060fd64] igmp_group_added+0x164/0x190
[   89.420878] [e959dca0] [c060ffa8] ip_mc_inc_group+0x218/0x460
[   89.426617] [e959dce0] [c06120fc] ip_mc_up+0x3c/0x190
[   89.431662] [e959dd10] [c0607270] inetdev_event+0x250/0x620
[   89.437227] [e959dd50] [c005f190] notifier_call_chain+0x80/0xf0
[   89.443138] [e959dd80] [c0573a74] __dev_notify_flags+0x54/0xf0
[   89.448964] [e959dda0] [c05743f8] dev_change_flags+0x48/0x60
[   89.454615] [e959ddc0] [c0606744] devinet_ioctl+0x544/0x8a0
[   89.460180] [e959de10] [c060987c] inet_ioctl+0x9c/0x1f0
[   89.465400] [e959de80] [c05479a8] sock_ioctl+0x168/0x460
[   89.470708] [e959ded0] [c01cf3ec] do_vfs_ioctl+0xac/0x8c0
[   89.476099] [e959df20] [c01cfc40] SyS_ioctl+0x40/0xc0
[   89.481147] [e959df40] [c0011318] ret_from_syscall+0x0/0x3c
[   89.486715] --- interrupt: c01 at 0x1006943c
[   89.486715]     LR = 0x100c45ec
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paul Blakey says:

====================
rhashtable: Fix rhltable duplicates insertion

On our mlx5 driver fs_core.c, we use the rhltable interface to store
flow groups. We noticed that sometimes we get a warning that flow group isn't
found at removal. This rare case was caused when a specific scenario happened,
insertion of a flow group with a similar match criteria (a duplicate),
but only where the flow group rhash_head was second (or not first)
on the relevant rhashtable bucket list.

The first patch fixes it, and the second one adds a test that show
it is now working.

Paul.

v3 --> v2 changes:
    * added missing fix in rhashtable_lookup_one code path as well.

v1 --> v2 changes:
    * Changed commit messages to better reflect the change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tries to insert duplicates in the middle of bucket's chain:
bucket 1:  [[val 21 (tid=1)]] -> [[ val 1 (tid=2),  val 1 (tid=0) ]]

Reuses tid to distinguish the elements insertion order.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When inserting duplicate objects (those with the same key),
current rhlist implementation messes up the chain pointers by
updating the bucket pointer instead of prev next pointer to the
newly inserted node. This causes missing elements on removal and
travesal.

Fix that by properly updating pprev pointer to point to
the correct rhash_head next pointer.

Issue: 1241076
Change-Id: I86b2c140bcb4aeb10b70a72a267ff590bb2b17e7
Fixes: ca26893f ('rhashtable: Add rhlist interface')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Stream Buffer for EtherAVB-IF (STBE) is an optional component, and
is not present on all SoCs.

Document this in the DT bindings, including a list of SoCs that do have
it.

Fixes: 785ec874 ("ravb: document R8A77970 bindings")
Fixes: f231c417 ("dt-bindings: net: renesas-ravb: Add support for R8A77995 RAVB")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.

Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The feature module needs to evaluate the actual firmware error return
upon a control command. This adds a flag to struct brcmf_if that the
caller can set. This flag is checked to determine the error code that
needs to be returned.

Fixes: b69c1df4 ("brcmfmac: separate firmware errors from i/o errors")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Compilation of bpftool on a distro that lacks eBPF support in the installed
kernel headers fails with:

common.c: In function ‘is_bpffs’:
common.c:96:40: error: ‘BPF_FS_MAGIC’ undeclared (first use in this function)
  return (unsigned long)st_fs.f_type == BPF_FS_MAGIC;
                                        ^
Fix this the same way it is already in tools/lib/bpf/libbpf.c and
tools/lib/api/fs/fs.c.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Only allow ifindex from IP_PKTINFO to override SO_BINDTODEVICE settings
if the index is actually set in the message.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling of National Semi-conductor (no hyphen)
in drivers/net/ethernet/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Use strlcpy() for ethtool::get_strings

After turning on KASAN on one of my systems, I started getting lots of out of
bounds errors while fetching a given port's statistics, and indeed using
memcpy() is unsafe for copying strings which have not been declared as an array
of ETH_GSTRING_LEN bytes, so let's use strlcpy() instead. This allows the best
of both worlds: we still keep the efficient memory usage of variably sized
strings, but we don't copy more than we need to.

Changes in v2:
- dropped the 3 other patches that were not necessary
- use strlcpy() instead of strncpy()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: 820ee17b ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: 2b2427d0 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: d2fa47d9 ("phy: marvell: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: 967dd82f ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>