- 22 Mar, 2023 23 commits
-
-
Gergo Koteles authored
Enable the Hall effect sensor (flip cover) for OnePlus 6/6T. The GPIO is mapped to SW_LID events as in msm8916, msm8994, msm8998 devices. Signed-off-by:
Gergo Koteles <soyer@irl.hu> Reviewed-by:
Caleb Connolly <caleb@connolly.tech> Reviewed-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230306174147.185239-1-soyer@irl.hu
-
Krzysztof Kozlowski authored
Remove trailing, redundant line breaks. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Drop empty override of pm8998_gpios. Signed-off-by:
-
Krzysztof Kozlowski authored
Bindings expect thermal node names to end with '-thermal', so fix pm660 and pm660l: sda660-inforce-ifc6560.dtb: thermal-zones: 'pm660', 'pm660l' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+' Signed-off-by: -
Krzysztof Kozlowski authored
The "dr_mode" is a property of USB DWC3 node, not the Qualcomm wrapper one: sm8350-microsoft-surface-duo2.dtb: usb@a6f8800: 'dr_mode' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+' Fixes: c16160cf ("arm64: dts: qcom: add minimal DTS for Microsoft Surface Duo 2") Signed-off-by:
-
Krzysztof Kozlowski authored
Fix typo in USB DWC3 node maximum speed property. Fixes: a41b6175 ("arm64: dts: qcom: sm8250: Add device tree for Xiaomi Mi Pad 5 Pro") Signed-off-by:
-
Bartosz Golaszewski authored
Enable the high-speed UART port connected to the Bluetooth controller on the sa8775p-adp development board. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by:
-
Bartosz Golaszewski authored
Enable the high-speed UART port connected to the GNSS controller on the sa8775p-adp development board. Signed-off-by:
-
Bartosz Golaszewski authored
Add two UART nodes that are known to be used by existing development boards with this SoC. Signed-off-by:
-
Bartosz Golaszewski authored
Enable the SPI interface exposed on the sa8775p-ride development board. Signed-off-by:
-
Bartosz Golaszewski authored
Add the SPI controller node for the interface exposed on the sa8775p-ride development board. Signed-off-by:
-
Bartosz Golaszewski authored
This enables the I2C interface on the sa8775p-ride development board. Signed-off-by:
-
Bartosz Golaszewski authored
Add a disabled node for the I2C interface that's exposed on the sa8775p-ride development board. Signed-off-by:
-
Bartosz Golaszewski authored
Enable the second instance of the QUPv3 engine on the sa8775p-ride board. Signed-off-by:
-
Bartosz Golaszewski authored
Add the second instance of the QUPv3 engine to the sa8775p.dtsi. Signed-off-by:
-
Danila Tikhonov authored
Add a node describing the flash block found on pm8150l. Signed-off-by:
Danila Tikhonov <danila@jiaxyga.com> Signed-off-by:
-
Bhupesh Sharma authored
As per documentation, Qualcomm SDM845 SoC supports BAM DMA engine v1.7.4, so use the correct compatible strings. Signed-off-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by:
-
Neil Armstrong authored
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Neil Armstrong authored
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Reviewed-by:
-
Neil Armstrong authored
Add the pmic glink node linked with the DWC3 USB controller switched to OTG mode and tagged with usb-role-switch. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
-
Neil Armstrong authored
Add ports subnodes in dwc3 node to avoid repeating the same description in each board DT. Reviewed-by:
-
Neil Armstrong authored
Add ports subnodes in dwc3 node to avoid repeating the same description in each board DT. Reviewed-by:
-
Neil Armstrong authored
Add ports subnodes in dwc3 node to avoid repeating the same description in each board DT. Reviewed-by:
-
- 20 Mar, 2023 3 commits
-
-
Bhupesh Sharma authored
Normally the 'pinctrl' properties of a SDHC controller and the chip detect pin settings are dependent on the type of the slots (for e.g uSD card slot), regulators and GPIO(s) available on the board(s). So, move the same from the sm6115 dtsi file to the respective board file(s). Reviewed-by:
Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
-
Bhupesh Sharma authored
Normally the 'maximum-speed' and 'dr_mode' properties of a USB controller + port is dependent on the type of the ports, regulators and mode change interrupt routing available on the board(s). So, move the same from the sm6115 dtsi file to respective board file(s). Reviewed-by:
-
Bhupesh Sharma authored
There is only one USB controller present on SM6115 / SM4250 Qualcomm SoC, so drop the numbering used with USB node's label names in the dtsi and the related sm4250-oneplus-billie2.dts. Reviewed-by:
-
- 16 Mar, 2023 14 commits
-
-
Johan Hovold authored
Fix the external display controller nodes which erroneously described the controllers as belonging to CX rather than MMCX. Fixes: 19d3bb90 ("arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks") Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Signed-off-by:
-
Stephan Gerhold authored
The reg address of the tsens_mode nvmem cell is correct but the unit address does not match (0xec vs 0xef). Fix it. No functional change. Fixes: 24aafd04 ("arm64: dts: qcom: msm8916: specify per-sensor calibration cells") Signed-off-by:
Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by:
-
Neil Armstrong authored
Miscellaneous DT fixes to remove spurious blank line and enhance readability. Fixes: ffc50b2d ("arm64: dts: qcom: Add base SM8550 dtsi") Fixes: d7da51db ("arm64: dts: qcom: sm8550: add display hardware devices") Signed-off-by:
-
Neil Armstrong authored
The node is incomplete and doesn't need a subnode, add the missing properties and move everything to the root of qup-spi0-cs-state node. Fixes: ffc50b2d ("arm64: dts: qcom: Add base SM8550 dtsi") Signed-off-by:
-
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sm8250-xiaomi-elish.dtb: gpio-keys: key-vol-up: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sm8250-sony-xperia-edo-pdx206.dtb: gpio-keys: key-vol-down: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sm6115p-lenovo-j606f.dtb: gpio-keys: key-volume-up: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sdm630-sony-xperia-nile-voyager.dtb: gpio-keys: key-vol-down: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sc7280-idp.dtb: gpio-keys: key-volume-up: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: msm8998-sony-xperia-yoshino-lilac.dtb: gpio-keys: button-vol-down: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: msm8998-fxtec-pro1.dtb: gpio-hall-sensors: event-hall-sensor1: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Krzysztof Kozlowski authored
gpio-keys,wakeup is a deprecated property: sm8150-sony-xperia-kumano-bahamut.dtb: gpio-keys: key-camera-focus: Unevaluated properties are not allowed ('gpio-key,wakeup' was unexpected) Signed-off-by: -
Douglas Anderson authored
The mrbland board was never actually produced and there has been no activity around the board for quite some time. It seems highly unlikely to magically get revived. There should be nobody in need of these device trees, so let's delete them. If somehow the project resurrects itself then we can re-add support, perhaps just for -rev1+. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
-
Douglas Anderson authored
lazor-rev0 was a pile of parts. While I kept the pile of parts for lazor running on my desk for longer than I usually do, those days are still long past. Let's finally delete support for lazor-rev0. Signed-off-by:
-
