The menz127 driver tries to support open drain by detecting it
at request time. However: without the new callbacks from the
gpiolib it is not really working: the core will still just emulate
the open drain mode by switching the line to an input.

By adding a hook into the new .set_single_ended() call rather than
trying to autodetect at request() time, proper open drain can be
supported.

Cc: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The F7188x chips supports setting the pins in open drain mode.
Activate the new .set_single_ended() callback.

Cc: Peter Hung <hpeter@gmail.com>
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Align to how we handle bitmasks in most drivers in the
subsystem: using the BIT(n) macro over (1 << n).

Cc: Peter Hung <hpeter@gmail.com>
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

One variant of the SX150X GPIO chip supports setting the pins in
open drain mode. This is currently available to set from platform
data, but completely unused in the kernel.

Activate the new .set_single_ended() callback so users can set
this up from e.g. device tree or board files using the new
GPIO descriptors.

As part of this, delete the platform data open drain setting
method.

Cc: Wei Chen <Wei.Chen@csr.com>
Cc: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The sx150x has some platform data definition in <linux/i2c/sx150x.h>
but this file is only included from the driver in the whole kernel
so move its contents into the driver.

Cc: Wei Chen <Wei.Chen@csr.com>
Cc: Peter Rosin <peda@axentia.se>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The TPS65218 supports open drain mode on its three pins,
with one of them configurable also as push-pull. Use the
new .set_single_ended() callback to set this up properly
from the core, so the core actually see it can drive the
pin(s) as open drain, and does not attempt to emulate
open drain by switching the pin to an input.
Acked-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If GPIO hog configuration failed while adding OF based
gpiochip() then return the error instead of ignoring it.

This helps of properly handling the gpio driver dependency.

When adding the gpio hog nodes for NVIDIA's Tegra210 platforms,
the gpio_hogd() fails with EPROBE_DEFER because pinctrl is not
ready at this time and gpio_request() for Tegra GPIO driver
returns error. The error was not causing the Tegra GPIO driver
to fail as the error was getting ignored.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Benoit Parrot <bparrot@ti.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Helps get_maintainer.pl to find the right people.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
it is different from PCA9535 and includes interrupt mask/status registers,
The current driver does not support the interrupt registers configuration,
it causes some gpio pins cannot trigger interrupt events,
this patch fix this issue.

The original patch was submitted by
Josef Ahmad <josef.ahmad@linux.intel.com>
http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patchSigned-off-by: Yong Li <yong.b.li@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pm_runtime_disable is called only in remove it is missed
out in the error path.
Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds GPIO driver for Loongson1B.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This has been a totally undocumented feature for years so add some
generic concepts and documentation about open drain/source, include
some facts on how we now support for hardware.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_TPS6586X
drivers/gpio/Kconfig:   bool "TPS6586X GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_TPS65910
drivers/gpio/Kconfig:   bool "TPS65910 GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_PALMAS
drivers/gpio/Kconfig:   bool "TI PALMAS series PMICs GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_SX150X
drivers/gpio/Kconfig:   bool "Semtech SX150x I2C GPIO expander"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Gregory Bean <gbean@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_TC3589X
drivers/gpio/Kconfig:   bool "TC3589X GPIOs"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_RC5T583
drivers/gpio/Kconfig:   bool "RICOH RC5T583 GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes use of the new .set_single_ended() callback to
set the GPIO line as open drain/open source using hardware.
The TC3589x can do this by either disabling the N-MOS
transistor (open drain) or the P-MOS transistor (open source)
of the output driver stage, in the first case making the signal
drive actively low and high impedance as "high" and in the second
case actively high and high impedance, which is as close to native
open drain support as we come.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This switch to use BIT(n) instead of (1 << n) which is less
to the point. Most GPIO drivers do this to avoid mistakes.
Also switch from using <linux/gpio.h> to the apropriate
<linux/gpio/driver.h> include.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.

We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

i2c_smbus_write_byte_data() can fail. To ensure the
cached buffer has consistent status with h/w status, don't
update the cached gpio->buffer if write fails.

Also refactor the code a bit by adding a tpic2810_set_mask_bits()
helper and use it to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

config GPIO_ZX
        bool "ZTE ZX GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_XGENE
drivers/gpio/Kconfig:   bool "APM X-Gene GPIO controller support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Feng Kan <fkan@apm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_STA2X11
drivers/gpio/Kconfig:   bool "STA2x11/ConneXt GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity, so that when reading
the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this driver is currently:

config GPIO_PL061
        bool "PrimeCell PL061 GPIO support"

...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MVEBU
drivers/gpio/Kconfig:   def_bool y

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MOXART
drivers/gpio/Kconfig:   bool "MOXART GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular references so that when reading
the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MC9S08DZ60
drivers/gpio/Kconfig:   bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Wu Guoxing <b39297@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this driver is currently:

config GPIO_MB86S7X
        bool "GPIO support for Fujitsu MB86S7x Platforms"

...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

config GPIO_BCM_KONA
        bool "Broadcom Kona GPIO"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Ray Jui <rjui@broadcom.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.

I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

lsgpio.c: In function ‘main’:
lsgpio.c:166:7: warning: ‘device_name’ may be used uninitialized in this functio
n [-Wmaybe-uninitialized]
   ret = list_device(device_name);
       ^
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Cc: devicetree@vger.kernel.org
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

- Add GPIO support for Broadcom Vulcan ARM64.
- Add depends on ARCH_VULCAN to Kconfig to enable gpio controller
  driver for Broadcom Vulcan ARM64 SoCs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Update the NXP GPIO node dt-binding file for QorIQ and
Layerscape platforms, and add one more example with
ls2080a GPIO node.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The chip is also an 8 bit shift register which works out of the box as a GPO
expander with this patch
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>