[ Upstream commit 1ca0fafd ]

This essentially reverts commit 72123032 ("tcp: md5: reject TCP_MD5SIG
or TCP_MD5SIG_EXT on established sockets")

Mathieu reported that many vendors BGP implementations can
actually switch TCP MD5 on established flows.

Quoting Mathieu :
   Here is a list of a few network vendors along with their behavior
   with respect to TCP MD5:

   - Cisco: Allows for password to be changed, but within the hold-down
     timer (~180 seconds).
   - Juniper: When password is initially set on active connection it will
     reset, but after that any subsequent password changes no network
     resets.
   - Nokia: No notes on if they flap the tcp connection or not.
   - Ericsson/RedBack: Allows for 2 password (old/new) to co-exist until
     both sides are ok with new passwords.
   - Meta-Switch: Expects the password to be set before a connection is
     attempted, but no further info on whether they reset the TCP
     connection on a change.
   - Avaya: Disable the neighbor, then set password, then re-enable.
   - Zebos: Would normally allow the change when socket connected.

We can revert my prior change because commit 9424e2e7 ("tcp: md5: fix potential
overestimation of TCP option space") removed the leak of 4 kernel bytes to
the wire that was the main reason for my patch.

While doing my investigations, I found a bug when a MD5 key is changed, leading
to these commits that stable teams want to consider before backporting this revert :

 Commit 6a2febec ("tcp: md5: add missing memory barriers in tcp_md5_do_add()/tcp_md5_hash_key()")
 Commit e6ced831 ("tcp: md5: refine tcp_md5_do_add()/tcp_md5_hash_key() barriers")

Fixes: 72123032 "tcp: md5: reject TCP_MD5SIG or TCP_MD5SIG_EXT on established sockets"
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e6ced831 ]

My prior fix went a bit too far, according to Herbert and Mathieu.

Since we accept that concurrent TCP MD5 lookups might see inconsistent
keys, we can use READ_ONCE()/WRITE_ONCE() instead of smp_rmb()/smp_wmb()

Clearing all key->key[] is needed to avoid possible KMSAN reports,
if key->keylen is increased. Since tcp_md5_do_add() is not fast path,
using __GFP_ZERO to clear all struct tcp_md5sig_key is simpler.

data_race() was added in linux-5.8 and will prevent KCSAN reports,
this can safely be removed in stable backports, if data_race() is
not yet backported.

v2: use data_race() both in tcp_md5_hash_key() and tcp_md5_do_add()

Fixes: 6a2febec ("tcp: md5: add missing memory barriers in tcp_md5_do_add()/tcp_md5_hash_key()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Marco Elver <elver@google.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e114e1e8 ]

Whenever cookie_init_timestamp() has been used to encode
ECN,SACK,WSCALE options, we can not remove the TS option in the SYNACK.

Otherwise, tcp_synack_options() will still advertize options like WSCALE
that we can not deduce later when receiving the packet from the client
to complete 3WHS.

Note that modern linux TCP stacks wont use MD5+TS+SACK in a SYN packet,
but we can not know for sure that all TCP stacks have the same logic.

Before the fix a tcpdump would exhibit this wrong exchange :

10:12:15.464591 IP C > S: Flags [S], seq 4202415601, win 65535, options [nop,nop,md5 valid,mss 1400,sackOK,TS val 456965269 ecr 0,nop,wscale 8], length 0
10:12:15.464602 IP S > C: Flags [S.], seq 253516766, ack 4202415602, win 65535, options [nop,nop,md5 valid,mss 1400,nop,nop,sackOK,nop,wscale 8], length 0
10:12:15.464611 IP C > S: Flags [.], ack 1, win 256, options [nop,nop,md5 valid], length 0
10:12:15.464678 IP C > S: Flags [P.], seq 1:13, ack 1, win 256, options [nop,nop,md5 valid], length 12
10:12:15.464685 IP S > C: Flags [.], ack 13, win 65535, options [nop,nop,md5 valid], length 0

After this patch the exchange looks saner :

11:59:59.882990 IP C > S: Flags [S], seq 517075944, win 65535, options [nop,nop,md5 valid,mss 1400,sackOK,TS val 1751508483 ecr 0,nop,wscale 8], length 0
11:59:59.883002 IP S > C: Flags [S.], seq 1902939253, ack 517075945, win 65535, options [nop,nop,md5 valid,mss 1400,sackOK,TS val 1751508479 ecr 1751508483,nop,wscale 8], length 0
11:59:59.883012 IP C > S: Flags [.], ack 1, win 256, options [nop,nop,md5 valid,nop,nop,TS val 1751508483 ecr 1751508479], length 0
11:59:59.883114 IP C > S: Flags [P.], seq 1:13, ack 1, win 256, options [nop,nop,md5 valid,nop,nop,TS val 1751508483 ecr 1751508479], length 12
11:59:59.883122 IP S > C: Flags [.], ack 13, win 256, options [nop,nop,md5 valid,nop,nop,TS val 1751508483 ecr 1751508483], length 0
11:59:59.883152 IP S > C: Flags [P.], seq 1:13, ack 13, win 256, options [nop,nop,md5 valid,nop,nop,TS val 1751508484 ecr 1751508483], length 12
11:59:59.883170 IP C > S: Flags [.], ack 13, win 256, options [nop,nop,md5 valid,nop,nop,TS val 1751508484 ecr 1751508484], length 0

Of course, no SACK block will ever be added later, but nothing should break.
Technically, we could remove the 4 nops included in MD5+TS options,
but again some stacks could break seeing not conventional alignment.

Fixes: 4957faad ("TCPCT part 1g: Responder Cookie => Initiator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6a2febec ]

MD5 keys are read with RCU protection, and tcp_md5_do_add()
might update in-place a prior key.

Normally, typical RCU updates would allocate a new piece
of memory. In this case only key->key and key->keylen might
be updated, and we do not care if an incoming packet could
see the old key, the new one, or some intermediate value,
since changing the key on a live flow is known to be problematic
anyway.

We only want to make sure that in the case key->keylen
is changed, cpus in tcp_md5_hash_key() wont try to use
uninitialized data, or crash because key->keylen was
read twice to feed sg_init_one() and ahash_request_set_crypt()

Fixes: 9ea88a15 ("tcp: md5: check md5 signature without socket lock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ce69e563 ]

syzkaller found its way into setsockopt with TCP_CONGESTION "cdg".
tcp_cdg_init() does a kcalloc to store the gradients. As sk_clone_lock
just copies all the memory, the allocated pointer will be copied as
well, if the app called setsockopt(..., TCP_CONGESTION) on the listener.
If now the socket will be destroyed before the congestion-control
has properly been initialized (through a call to tcp_init_transfer), we
will end up freeing memory that does not belong to that particular
socket, opening the door to a double-free:

[   11.413102] ==================================================================
[   11.414181] BUG: KASAN: double-free or invalid-free in tcp_cleanup_congestion_control+0x58/0xd0
[   11.415329]
[   11.415560] CPU: 3 PID: 4884 Comm: syz-executor.5 Not tainted 5.8.0-rc2 #80
[   11.416544] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[   11.418148] Call Trace:
[   11.418534]  <IRQ>
[   11.418834]  dump_stack+0x7d/0xb0
[   11.419297]  print_address_description.constprop.0+0x1a/0x210
[   11.422079]  kasan_report_invalid_free+0x51/0x80
[   11.423433]  __kasan_slab_free+0x15e/0x170
[   11.424761]  kfree+0x8c/0x230
[   11.425157]  tcp_cleanup_congestion_control+0x58/0xd0
[   11.425872]  tcp_v4_destroy_sock+0x57/0x5a0
[   11.426493]  inet_csk_destroy_sock+0x153/0x2c0
[   11.427093]  tcp_v4_syn_recv_sock+0xb29/0x1100
[   11.427731]  tcp_get_cookie_sock+0xc3/0x4a0
[   11.429457]  cookie_v4_check+0x13d0/0x2500
[   11.433189]  tcp_v4_do_rcv+0x60e/0x780
[   11.433727]  tcp_v4_rcv+0x2869/0x2e10
[   11.437143]  ip_protocol_deliver_rcu+0x23/0x190
[   11.437810]  ip_local_deliver+0x294/0x350
[   11.439566]  __netif_receive_skb_one_core+0x15d/0x1a0
[   11.441995]  process_backlog+0x1b1/0x6b0
[   11.443148]  net_rx_action+0x37e/0xc40
[   11.445361]  __do_softirq+0x18c/0x61a
[   11.445881]  asm_call_on_stack+0x12/0x20
[   11.446409]  </IRQ>
[   11.446716]  do_softirq_own_stack+0x34/0x40
[   11.447259]  do_softirq.part.0+0x26/0x30
[   11.447827]  __local_bh_enable_ip+0x46/0x50
[   11.448406]  ip_finish_output2+0x60f/0x1bc0
[   11.450109]  __ip_queue_xmit+0x71c/0x1b60
[   11.451861]  __tcp_transmit_skb+0x1727/0x3bb0
[   11.453789]  tcp_rcv_state_process+0x3070/0x4d3a
[   11.456810]  tcp_v4_do_rcv+0x2ad/0x780
[   11.457995]  __release_sock+0x14b/0x2c0
[   11.458529]  release_sock+0x4a/0x170
[   11.459005]  __inet_stream_connect+0x467/0xc80
[   11.461435]  inet_stream_connect+0x4e/0xa0
[   11.462043]  __sys_connect+0x204/0x270
[   11.465515]  __x64_sys_connect+0x6a/0xb0
[   11.466088]  do_syscall_64+0x3e/0x70
[   11.466617]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   11.467341] RIP: 0033:0x7f56046dc469
[   11.467844] Code: Bad RIP value.
[   11.468282] RSP: 002b:00007f5604dccdd8 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
[   11.469326] RAX: ffffffffffffffda RBX: 000000000068bf00 RCX: 00007f56046dc469
[   11.470379] RDX: 0000000000000010 RSI: 0000000020000000 RDI: 0000000000000004
[   11.471311] RBP: 00000000ffffffff R08: 0000000000000000 R09: 0000000000000000
[   11.472286] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[   11.473341] R13: 000000000041427c R14: 00007f5604dcd5c0 R15: 0000000000000003
[   11.474321]
[   11.474527] Allocated by task 4884:
[   11.475031]  save_stack+0x1b/0x40
[   11.475548]  __kasan_kmalloc.constprop.0+0xc2/0xd0
[   11.476182]  tcp_cdg_init+0xf0/0x150
[   11.476744]  tcp_init_congestion_control+0x9b/0x3a0
[   11.477435]  tcp_set_congestion_control+0x270/0x32f
[   11.478088]  do_tcp_setsockopt.isra.0+0x521/0x1a00
[   11.478744]  __sys_setsockopt+0xff/0x1e0
[   11.479259]  __x64_sys_setsockopt+0xb5/0x150
[   11.479895]  do_syscall_64+0x3e/0x70
[   11.480395]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   11.481097]
[   11.481321] Freed by task 4872:
[   11.481783]  save_stack+0x1b/0x40
[   11.482230]  __kasan_slab_free+0x12c/0x170
[   11.482839]  kfree+0x8c/0x230
[   11.483240]  tcp_cleanup_congestion_control+0x58/0xd0
[   11.483948]  tcp_v4_destroy_sock+0x57/0x5a0
[   11.484502]  inet_csk_destroy_sock+0x153/0x2c0
[   11.485144]  tcp_close+0x932/0xfe0
[   11.485642]  inet_release+0xc1/0x1c0
[   11.486131]  __sock_release+0xc0/0x270
[   11.486697]  sock_close+0xc/0x10
[   11.487145]  __fput+0x277/0x780
[   11.487632]  task_work_run+0xeb/0x180
[   11.488118]  __prepare_exit_to_usermode+0x15a/0x160
[   11.488834]  do_syscall_64+0x4a/0x70
[   11.489326]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Wei Wang fixed a part of these CDG-malloc issues with commit c1201444
("tcp: memset ca_priv data to 0 properly").

This patch here fixes the listener-scenario: We make sure that listeners
setting the congestion-control through setsockopt won't initialize it
(thus CDG never allocates on listeners). For those who use AF_UNSPEC to
reuse a socket, tcp_disconnect() is changed to cleanup afterwards.

(The issue can be reproduced at least down to v4.4.x.)

Cc: Wei Wang <weiwan@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2b0a8c9e ("tcp: add CDG congestion control")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ba3bb0e7 ]

Whenever tcp_try_rmem_schedule() returns an error, we are under
trouble and should make sure to wakeup readers so that they
can drain socket queues and eventually make room.

Fixes: 03f45c88 ("tcp: avoid extra wakeups for SO_RCVLOWAT users")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f815dd5c ]

Add support for Quectel Wireless Solutions Co., Ltd. EG95 LTE modem

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0195 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 306381ae ]

When tcf_block_get() fails inside atm_tc_init(),
atm_tc_put() is called to release the qdisc p->link.q.
But the flow->ref prevents it to do so, as the flow->ref
is still zero.

Fix this by moving the p->link.ref initialization before
tcf_block_get().

Fixes: 6529eaba ("net: sched: introduce tcf block infractructure")
Reported-and-tested-by: syzbot+d411cff6ab29cc2c311b@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 394de110 ]

The packets from tunnel devices (eg bareudp) may have only
metadata in the dst pointer of skb. Hence a pointer check of
neigh_lookup is needed in dst_neigh_lookup_skb

Kernel crashes when packets from bareudp device is processed in
the kernel neighbour subsytem.

[  133.384484] BUG: kernel NULL pointer dereference, address: 0000000000000000
[  133.385240] #PF: supervisor instruction fetch in kernel mode
[  133.385828] #PF: error_code(0x0010) - not-present page
[  133.386603] PGD 0 P4D 0
[  133.386875] Oops: 0010 [#1] SMP PTI
[  133.387275] CPU: 0 PID: 5045 Comm: ping Tainted: G        W         5.8.0-rc2+ #15
[  133.388052] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[  133.391076] RIP: 0010:0x0
[  133.392401] Code: Bad RIP value.
[  133.394029] RSP: 0018:ffffb79980003d50 EFLAGS: 00010246
[  133.396656] RAX: 0000000080000102 RBX: ffff9de2fe0d6600 RCX: ffff9de2fe5e9d00
[  133.399018] RDX: 0000000000000000 RSI: ffff9de2fe5e9d00 RDI: ffff9de2fc21b400
[  133.399685] RBP: ffff9de2fe5e9d00 R08: 0000000000000000 R09: 0000000000000000
[  133.400350] R10: ffff9de2fbc6be22 R11: ffff9de2fe0d6600 R12: ffff9de2fc21b400
[  133.401010] R13: ffff9de2fe0d6628 R14: 0000000000000001 R15: 0000000000000003
[  133.401667] FS:  00007fe014918740(0000) GS:ffff9de2fec00000(0000) knlGS:0000000000000000
[  133.402412] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  133.402948] CR2: ffffffffffffffd6 CR3: 000000003bb72000 CR4: 00000000000006f0
[  133.403611] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  133.404270] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  133.404933] Call Trace:
[  133.405169]  <IRQ>
[  133.405367]  __neigh_update+0x5a4/0x8f0
[  133.405734]  arp_process+0x294/0x820
[  133.406076]  ? __netif_receive_skb_core+0x866/0xe70
[  133.406557]  arp_rcv+0x129/0x1c0
[  133.406882]  __netif_receive_skb_one_core+0x95/0xb0
[  133.407340]  process_backlog+0xa7/0x150
[  133.407705]  net_rx_action+0x2af/0x420
[  133.408457]  __do_softirq+0xda/0x2a8
[  133.408813]  asm_call_on_stack+0x12/0x20
[  133.409290]  </IRQ>
[  133.409519]  do_softirq_own_stack+0x39/0x50
[  133.410036]  do_softirq+0x50/0x60
[  133.410401]  __local_bh_enable_ip+0x50/0x60
[  133.410871]  ip_finish_output2+0x195/0x530
[  133.411288]  ip_output+0x72/0xf0
[  133.411673]  ? __ip_finish_output+0x1f0/0x1f0
[  133.412122]  ip_send_skb+0x15/0x40
[  133.412471]  raw_sendmsg+0x853/0xab0
[  133.412855]  ? insert_pfn+0xfe/0x270
[  133.413827]  ? vvar_fault+0xec/0x190
[  133.414772]  sock_sendmsg+0x57/0x80
[  133.415685]  __sys_sendto+0xdc/0x160
[  133.416605]  ? syscall_trace_enter+0x1d4/0x2b0
[  133.417679]  ? __audit_syscall_exit+0x1d9/0x280
[  133.418753]  ? __prepare_exit_to_usermode+0x5d/0x1a0
[  133.419819]  __x64_sys_sendto+0x24/0x30
[  133.420848]  do_syscall_64+0x4d/0x90
[  133.421768]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  133.422833] RIP: 0033:0x7fe013689c03
[  133.423749] Code: Bad RIP value.
[  133.424624] RSP: 002b:00007ffc7288f418 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[  133.425940] RAX: ffffffffffffffda RBX: 000056151fc63720 RCX: 00007fe013689c03
[  133.427225] RDX: 0000000000000040 RSI: 000056151fc63720 RDI: 0000000000000003
[  133.428481] RBP: 00007ffc72890b30 R08: 000056151fc60500 R09: 0000000000000010
[  133.429757] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[  133.431041] R13: 000056151fc636e0 R14: 000056151fc616bc R15: 0000000000000080
[  133.432481] Modules linked in: mpls_iptunnel act_mirred act_tunnel_key cls_flower sch_ingress veth mpls_router ip_tunnel bareudp ip6_udp_tunnel udp_tunnel macsec udp_diag inet_diag unix_diag af_packet_diag netlink_diag binfmt_misc xt_MASQUERADE iptable_nat xt_addrtype xt_conntrack nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc ebtable_filter ebtables overlay ip6table_filter ip6_tables iptable_filter sunrpc ext4 mbcache jbd2 pcspkr i2c_piix4 virtio_balloon joydev ip_tables xfs libcrc32c ata_generic qxl pata_acpi drm_ttm_helper ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm ata_piix libata virtio_net net_failover virtio_console failover virtio_blk i2c_core virtio_pci virtio_ring serio_raw floppy virtio dm_mirror dm_region_hash dm_log dm_mod
[  133.444045] CR2: 0000000000000000
[  133.445082] ---[ end trace f4aeee1958fd1638 ]---
[  133.446236] RIP: 0010:0x0
[  133.447180] Code: Bad RIP value.
[  133.448152] RSP: 0018:ffffb79980003d50 EFLAGS: 00010246
[  133.449363] RAX: 0000000080000102 RBX: ffff9de2fe0d6600 RCX: ffff9de2fe5e9d00
[  133.450835] RDX: 0000000000000000 RSI: ffff9de2fe5e9d00 RDI: ffff9de2fc21b400
[  133.452237] RBP: ffff9de2fe5e9d00 R08: 0000000000000000 R09: 0000000000000000
[  133.453722] R10: ffff9de2fbc6be22 R11: ffff9de2fe0d6600 R12: ffff9de2fc21b400
[  133.455149] R13: ffff9de2fe0d6628 R14: 0000000000000001 R15: 0000000000000003
[  133.456520] FS:  00007fe014918740(0000) GS:ffff9de2fec00000(0000) knlGS:0000000000000000
[  133.458046] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  133.459342] CR2: ffffffffffffffd6 CR3: 000000003bb72000 CR4: 00000000000006f0
[  133.460782] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  133.462240] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  133.463697] Kernel panic - not syncing: Fatal exception in interrupt
[  133.465226] Kernel Offset: 0xfa00000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[  133.467025] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Fixes: aaa0c23c ("Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a9b11101 ]

syzbot was to trigger a bug by tricking AF_LLC with
non sensible addr->sllc_arphrd

It seems clear LLC requires an Ethernet device.

Back in commit abf9d537 ("llc: add support for SO_BINDTODEVICE")
Octavian Purdila added possibility for application to use a zero
value for sllc_arphrd, convert it to ARPHRD_ETHER to not cause
regressions on existing applications.

BUG: KASAN: use-after-free in __read_once_size include/linux/compiler.h:199 [inline]
BUG: KASAN: use-after-free in list_empty include/linux/list.h:268 [inline]
BUG: KASAN: use-after-free in waitqueue_active include/linux/wait.h:126 [inline]
BUG: KASAN: use-after-free in wq_has_sleeper include/linux/wait.h:160 [inline]
BUG: KASAN: use-after-free in skwq_has_sleeper include/net/sock.h:2092 [inline]
BUG: KASAN: use-after-free in sock_def_write_space+0x642/0x670 net/core/sock.c:2813
Read of size 8 at addr ffff88801e0b4078 by task ksoftirqd/3/27

CPU: 3 PID: 27 Comm: ksoftirqd/3 Not tainted 5.5.0-rc1-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x197/0x210 lib/dump_stack.c:118
 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
 kasan_report+0x12/0x20 mm/kasan/common.c:639
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135
 __read_once_size include/linux/compiler.h:199 [inline]
 list_empty include/linux/list.h:268 [inline]
 waitqueue_active include/linux/wait.h:126 [inline]
 wq_has_sleeper include/linux/wait.h:160 [inline]
 skwq_has_sleeper include/net/sock.h:2092 [inline]
 sock_def_write_space+0x642/0x670 net/core/sock.c:2813
 sock_wfree+0x1e1/0x260 net/core/sock.c:1958
 skb_release_head_state+0xeb/0x260 net/core/skbuff.c:652
 skb_release_all+0x16/0x60 net/core/skbuff.c:663
 __kfree_skb net/core/skbuff.c:679 [inline]
 consume_skb net/core/skbuff.c:838 [inline]
 consume_skb+0xfb/0x410 net/core/skbuff.c:832
 __dev_kfree_skb_any+0xa4/0xd0 net/core/dev.c:2967
 dev_kfree_skb_any include/linux/netdevice.h:3650 [inline]
 e1000_unmap_and_free_tx_resource.isra.0+0x21b/0x3a0 drivers/net/ethernet/intel/e1000/e1000_main.c:1963
 e1000_clean_tx_irq drivers/net/ethernet/intel/e1000/e1000_main.c:3854 [inline]
 e1000_clean+0x4cc/0x1d10 drivers/net/ethernet/intel/e1000/e1000_main.c:3796
 napi_poll net/core/dev.c:6532 [inline]
 net_rx_action+0x508/0x1120 net/core/dev.c:6600
 __do_softirq+0x262/0x98c kernel/softirq.c:292
 run_ksoftirqd kernel/softirq.c:603 [inline]
 run_ksoftirqd+0x8e/0x110 kernel/softirq.c:595
 smpboot_thread_fn+0x6a3/0xa40 kernel/smpboot.c:165
 kthread+0x361/0x430 kernel/kthread.c:255
 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

Allocated by task 8247:
 save_stack+0x23/0x90 mm/kasan/common.c:72
 set_track mm/kasan/common.c:80 [inline]
 __kasan_kmalloc mm/kasan/common.c:513 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:486
 kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:521
 slab_post_alloc_hook mm/slab.h:584 [inline]
 slab_alloc mm/slab.c:3320 [inline]
 kmem_cache_alloc+0x121/0x710 mm/slab.c:3484
 sock_alloc_inode+0x1c/0x1d0 net/socket.c:240
 alloc_inode+0x68/0x1e0 fs/inode.c:230
 new_inode_pseudo+0x19/0xf0 fs/inode.c:919
 sock_alloc+0x41/0x270 net/socket.c:560
 __sock_create+0xc2/0x730 net/socket.c:1384
 sock_create net/socket.c:1471 [inline]
 __sys_socket+0x103/0x220 net/socket.c:1513
 __do_sys_socket net/socket.c:1522 [inline]
 __se_sys_socket net/socket.c:1520 [inline]
 __ia32_sys_socket+0x73/0xb0 net/socket.c:1520
 do_syscall_32_irqs_on arch/x86/entry/common.c:337 [inline]
 do_fast_syscall_32+0x27b/0xe16 arch/x86/entry/common.c:408
 entry_SYSENTER_compat+0x70/0x7f arch/x86/entry/entry_64_compat.S:139

Freed by task 17:
 save_stack+0x23/0x90 mm/kasan/common.c:72
 set_track mm/kasan/common.c:80 [inline]
 kasan_set_free_info mm/kasan/common.c:335 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:474
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:483
 __cache_free mm/slab.c:3426 [inline]
 kmem_cache_free+0x86/0x320 mm/slab.c:3694
 sock_free_inode+0x20/0x30 net/socket.c:261
 i_callback+0x44/0x80 fs/inode.c:219
 __rcu_reclaim kernel/rcu/rcu.h:222 [inline]
 rcu_do_batch kernel/rcu/tree.c:2183 [inline]
 rcu_core+0x570/0x1540 kernel/rcu/tree.c:2408
 rcu_core_si+0x9/0x10 kernel/rcu/tree.c:2417
 __do_softirq+0x262/0x98c kernel/softirq.c:292

The buggy address belongs to the object at ffff88801e0b4000
 which belongs to the cache sock_inode_cache of size 1152
The buggy address is located 120 bytes inside of
 1152-byte region [ffff88801e0b4000, ffff88801e0b4480)
The buggy address belongs to the page:
page:ffffea0000782d00 refcount:1 mapcount:0 mapping:ffff88807aa59c40 index:0xffff88801e0b4ffd
raw: 00fffe0000000200 ffffea00008e6c88 ffffea0000782d48 ffff88807aa59c40
raw: ffff88801e0b4ffd ffff88801e0b4000 0000000100000003 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff88801e0b3f00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
 ffff88801e0b3f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88801e0b4000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                                ^
 ffff88801e0b4080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff88801e0b4100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: abf9d537 ("llc: add support for SO_BINDTODEVICE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 27d53323 ]

In the tx path of l2tp, l2tp_xmit_skb() calls skb_dst_set() to set
skb's dst. However, it will eventually call inet6_csk_xmit() or
ip_queue_xmit() where skb's dst will be overwritten by:

   skb_dst_set_noref(skb, dst);

without releasing the old dst in skb. Then it causes dst/dev refcnt leak:

  unregister_netdevice: waiting for eth0 to become free. Usage count = 1

This can be reproduced by simply running:

  # modprobe l2tp_eth && modprobe l2tp_ip
  # sh ./tools/testing/selftests/net/l2tp.sh

So before going to inet6_csk_xmit() or ip_queue_xmit(), skb's dst
should be dropped. This patch is to fix it by removing skb_dst_set()
from l2tp_xmit_skb() and moving skb_dst_drop() into l2tp_xmit_core().

Fixes: 3557baab ("[L2TP]: PPP over L2TP driver core")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Tested-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5eff0690 ]

IPv4 ping sockets don't set fl4.fl4_icmp_{type,code}, which leads to
incomplete IPsec ACQUIRE messages being sent to userspace. Currently,
both raw sockets and IPv6 ping sockets set those fields.

Expected output of "ip xfrm monitor":
    acquire proto esp
      sel src 10.0.2.15/32 dst 8.8.8.8/32 proto icmp type 8 code 0 dev ens4
      policy src 10.0.2.15/32 dst 8.8.8.8/32
        <snip>

Currently with ping sockets:
    acquire proto esp
      sel src 10.0.2.15/32 dst 8.8.8.8/32 proto icmp type 0 code 0 dev ens4
      policy src 10.0.2.15/32 dst 8.8.8.8/32
        <snip>

The Libreswan test suite found this problem after Fedora changed the
value for the sysctl net.ipv4.ping_group_range.

Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Paul Wouters <pwouters@redhat.com>
Tested-by: Paul Wouters <pwouters@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1e82a62f ]

A potential deadlock can occur during registering or unregistering a
new generic netlink family between the main nl_table_lock and the
cb_lock where each thread wants the lock held by the other, as
demonstrated below.

1) Thread 1 is performing a netlink_bind() operation on a socket. As part
   of this call, it will call netlink_lock_table(), incrementing the
   nl_table_users count to 1.
2) Thread 2 is registering (or unregistering) a genl_family via the
   genl_(un)register_family() API. The cb_lock semaphore will be taken for
   writing.
3) Thread 1 will call genl_bind() as part of the bind operation to handle
   subscribing to GENL multicast groups at the request of the user. It will
   attempt to take the cb_lock semaphore for reading, but it will fail and
   be scheduled away, waiting for Thread 2 to finish the write.
4) Thread 2 will call netlink_table_grab() during the (un)registration
   call. However, as Thread 1 has incremented nl_table_users, it will not
   be able to proceed, and both threads will be stuck waiting for the
   other.

genl_bind() is a noop, unless a genl_family implements the mcast_bind()
function to handle setting up family-specific multicast operations. Since
no one in-tree uses this functionality as Cong pointed out, simply removing
the genl_bind() function will remove the possibility for deadlock, as there
is no attempt by Thread 1 above to take the cb_lock semaphore.

Fixes: c380d9a7 ("genetlink: pass multicast bind/unbind to families")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2a762e9e upstream.

There are two types of the lower interface of rmnet that are VND
and BRIDGE.
Each lower interface can have only one type either VND or BRIDGE.
But, there is a case, which uses both lower interface types.
Due to this unexpected behavior, lower interface leak occurs.

Test commands:
    ip link add dummy0 type dummy
    ip link add dummy1 type dummy
    ip link add rmnet0 link dummy0 type rmnet mux_id 1
    ip link set dummy1 master rmnet0
    ip link add rmnet1 link dummy1 type rmnet mux_id 2
    ip link del rmnet0

The dummy1 was attached as BRIDGE interface of rmnet0.
Then, it also was attached as VND interface of rmnet1.
This is unexpected behavior and there is no code for handling this case.
So that below splat occurs when the rmnet0 interface is deleted.

Splat looks like:
[   53.254112][    C1] WARNING: CPU: 1 PID: 1192 at net/core/dev.c:8992 rollback_registered_many+0x986/0xcf0
[   53.254117][    C1] Modules linked in: rmnet dummy openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nfx
[   53.254182][    C1] CPU: 1 PID: 1192 Comm: ip Not tainted 5.8.0-rc1+ #620
[   53.254188][    C1] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   53.254192][    C1] RIP: 0010:rollback_registered_many+0x986/0xcf0
[   53.254200][    C1] Code: 41 8b 4e cc 45 31 c0 31 d2 4c 89 ee 48 89 df e8 e0 47 ff ff 85 c0 0f 84 cd fc ff ff 0f 0b e5
[   53.254205][    C1] RSP: 0018:ffff888050a5f2e0 EFLAGS: 00010287
[   53.254214][    C1] RAX: ffff88805756d658 RBX: ffff88804d99c000 RCX: ffffffff8329d323
[   53.254219][    C1] RDX: 1ffffffff0be6410 RSI: 0000000000000008 RDI: ffffffff85f32080
[   53.254223][    C1] RBP: dffffc0000000000 R08: fffffbfff0be6411 R09: fffffbfff0be6411
[   53.254228][    C1] R10: ffffffff85f32087 R11: 0000000000000001 R12: ffff888050a5f480
[   53.254233][    C1] R13: ffff88804d99c0b8 R14: ffff888050a5f400 R15: ffff8880548ebe40
[   53.254238][    C1] FS:  00007f6b86b370c0(0000) GS:ffff88806c200000(0000) knlGS:0000000000000000
[   53.254243][    C1] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   53.254248][    C1] CR2: 0000562c62438758 CR3: 000000003f600005 CR4: 00000000000606e0
[   53.254253][    C1] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   53.254257][    C1] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   53.254261][    C1] Call Trace:
[   53.254266][    C1]  ? lockdep_hardirqs_on_prepare+0x379/0x540
[   53.254270][    C1]  ? netif_set_real_num_tx_queues+0x780/0x780
[   53.254275][    C1]  ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[   53.254279][    C1]  ? __kasan_slab_free+0x126/0x150
[   53.254283][    C1]  ? kfree+0xdc/0x320
[   53.254288][    C1]  ? rmnet_unregister_real_device+0x56/0x90 [rmnet]
[   53.254293][    C1]  unregister_netdevice_many.part.135+0x13/0x1b0
[   53.254297][    C1]  rtnl_delete_link+0xbc/0x100
[   53.254301][    C1]  ? rtnl_af_register+0xc0/0xc0
[   53.254305][    C1]  rtnl_dellink+0x2dc/0x840
[   53.254309][    C1]  ? find_held_lock+0x39/0x1d0
[   53.254314][    C1]  ? valid_fdb_dump_strict+0x620/0x620
[   53.254318][    C1]  ? rtnetlink_rcv_msg+0x457/0x890
[   53.254322][    C1]  ? lock_contended+0xd20/0xd20
[   53.254326][    C1]  rtnetlink_rcv_msg+0x4a8/0x890
[ ... ]
[   73.813696][ T1192] unregister_netdevice: waiting for rmnet0 to become free. Usage count = 1

Fixes: 037f9cdf ("net: rmnet: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0ada120c upstream.

libbfd has changed the bfd_section_* macros to inline functions
bfd_section_<field> since 2019-09-18. See below two commits:
  o http://www.sourceware.org/ml/gdb-cvs/2019-09/msg00064.html
  o https://www.sourceware.org/ml/gdb-cvs/2019-09/msg00072.html

This fix make perf able to build with both old and new libbfd.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200128152938.31413-1-changbin.du@gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jianmin Wang <jianmin@iscas.ac.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 528a9539 upstream.

If the pmd is soft dirty we must mark the pte as soft dirty (and not dirty).
This fixes some cases for guest migration with huge page backings.

Cc: <stable@vger.kernel.org> # 4.8
Fixes: bc29b7ac ("s390/mm: clean up pte/pmd encoding")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7faf971 upstream.

Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 00fdec98 upstream.

Trap handler for syscall tracing reads EFA (Exception Fault Address),
in case strace wants PC of trap instruction (EFA is not part of pt_regs
as of current code).

However this EFA read is racy as it happens after dropping to pure
kernel mode (re-enabling interrupts). A taken interrupt could
context-switch, trigger a different task's trap, clobbering EFA for this
execution context.

Fix this by reading EFA early, before re-enabling interrupts. A slight
side benefit is de-duplication of FAKE_RET_FROM_EXCPN in trap handler.
The trap handler is common to both ARCompact and ARCv2 builds too.

This just came out of code rework/review and no real problem was reported
but is clearly a potential problem specially for strace.

Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6958c1c6 upstream.

kobject_uevent may allocate memory and it may be called while there are dm
devices suspended. The allocation may recurse into a suspended device,
causing a deadlock. We must set the noio flag when sending a uevent.

The observed deadlock was reported here:
https://www.redhat.com/archives/dm-devel/2020-March/msg00025.htmlReported-by: Khazhismel Kumykov <khazhy@google.com>
Reported-by: Tahsin Erdogan <tahsin@google.com>
Reported-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 41855a89 upstream.

clang static analysis flags this error

drivers/gpu/drm/radeon/ci_dpm.c:5652:9: warning: Use of memory after it is freed [unix.Malloc]
                kfree(rdev->pm.dpm.ps[i].ps_priv);
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/radeon/ci_dpm.c:5654:2: warning: Attempt to free released memory [unix.Malloc]
        kfree(rdev->pm.dpm.ps);
        ^~~~~~~~~~~~~~~~~~~~~~

problem is reported in ci_dpm_fini, with these code blocks.

	for (i = 0; i < rdev->pm.dpm.num_ps; i++) {
		kfree(rdev->pm.dpm.ps[i].ps_priv);
	}
	kfree(rdev->pm.dpm.ps);

The first free happens in ci_parse_power_table where it cleans up locally
on a failure.  ci_dpm_fini also does a cleanup.

	ret = ci_parse_power_table(rdev);
	if (ret) {
		ci_dpm_fini(rdev);
		return ret;
	}

So remove the cleanup in ci_parse_power_table and
move the num_ps calculation to inside the loop so ci_dpm_fini
will know how many array elements to free.

Fixes: cc8dbbb4 ("drm/radeon: add dpm support for CI dGPUs (v2)")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6bf9cd2e upstream.

Under somewhat convoluted conditions, it is possible to attempt to
release an extent_buffer that is under io, which triggers a BUG_ON in
btrfs_release_extent_buffer_pages.

This relies on a few different factors. First, extent_buffer reads done
as readahead for searching use WAIT_NONE, so they free the local extent
buffer reference while the io is outstanding. However, they should still
be protected by TREE_REF. However, if the system is doing signficant
reclaim, and simultaneously heavily accessing the extent_buffers, it is
possible for releasepage to race with two concurrent readahead attempts
in a way that leaves TREE_REF unset when the readahead extent buffer is
released.

Essentially, if two tasks race to allocate a new extent_buffer, but the
winner who attempts the first io is rebuffed by a page being locked
(likely by the reclaim itself) then the loser will still go ahead with
issuing the readahead. The loser's call to find_extent_buffer must also
race with the reclaim task reading the extent_buffer's refcount as 1 in
a way that allows the reclaim to re-clear the TREE_REF checked by
find_extent_buffer.

The following represents an example execution demonstrating the race:

            CPU0                                                         CPU1                                           CPU2
reada_for_search                                            reada_for_search
  readahead_tree_block                                        readahead_tree_block
    find_create_tree_block                                      find_create_tree_block
      alloc_extent_buffer                                         alloc_extent_buffer
                                                                  find_extent_buffer // not found
                                                                  allocates eb
                                                                  lock pages
                                                                  associate pages to eb
                                                                  insert eb into radix tree
                                                                  set TREE_REF, refs == 2
                                                                  unlock pages
                                                              read_extent_buffer_pages // WAIT_NONE
                                                                not uptodate (brand new eb)
                                                                                                            lock_page
                                                                if !trylock_page
                                                                  goto unlock_exit // not an error
                                                              free_extent_buffer
                                                                release_extent_buffer
                                                                  atomic_dec_and_test refs to 1
        find_extent_buffer // found
                                                                                                            try_release_extent_buffer
                                                                                                              take refs_lock
                                                                                                              reads refs == 1; no io
          atomic_inc_not_zero refs to 2
          mark_buffer_accessed
            check_buffer_tree_ref
              // not STALE, won't take refs_lock
              refs == 2; TREE_REF set // no action
    read_extent_buffer_pages // WAIT_NONE
                                                                                                              clear TREE_REF
                                                                                                              release_extent_buffer
                                                                                                                atomic_dec_and_test refs to 1
                                                                                                                unlock_page
      still not uptodate (CPU1 read failed on trylock_page)
      locks pages
      set io_pages > 0
      submit io
      return
    free_extent_buffer
      release_extent_buffer
        dec refs to 0
        delete from radix tree
        btrfs_release_extent_buffer_pages
          BUG_ON(io_pages > 0)!!!

We observe this at a very low rate in production and were also able to
reproduce it in a test environment by introducing some spurious delays
and by introducing probabilistic trylock_page failures.

To fix it, we apply check_tree_ref at a point where it could not
possibly be unset by a competing task: after io_pages has been
incremented. All the codepaths that clear TREE_REF check for io, so they
would not be able to clear it after this point until the io is done.

Stack trace, for reference:
[1417839.424739] ------------[ cut here ]------------
[1417839.435328] kernel BUG at fs/btrfs/extent_io.c:4841!
[1417839.447024] invalid opcode: 0000 [#1] SMP
[1417839.502972] RIP: 0010:btrfs_release_extent_buffer_pages+0x20/0x1f0
[1417839.517008] Code: ed e9 ...
[1417839.558895] RSP: 0018:ffffc90020bcf798 EFLAGS: 00010202
[1417839.570816] RAX: 0000000000000002 RBX: ffff888102d6def0 RCX: 0000000000000028
[1417839.586962] RDX: 0000000000000002 RSI: ffff8887f0296482 RDI: ffff888102d6def0
[1417839.603108] RBP: ffff88885664a000 R08: 0000000000000046 R09: 0000000000000238
[1417839.619255] R10: 0000000000000028 R11: ffff88885664af68 R12: 0000000000000000
[1417839.635402] R13: 0000000000000000 R14: ffff88875f573ad0 R15: ffff888797aafd90
[1417839.651549] FS:  00007f5a844fa700(0000) GS:ffff88885f680000(0000) knlGS:0000000000000000
[1417839.669810] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1417839.682887] CR2: 00007f7884541fe0 CR3: 000000049f609002 CR4: 00000000003606e0
[1417839.699037] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1417839.715187] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1417839.731320] Call Trace:
[1417839.737103]  release_extent_buffer+0x39/0x90
[1417839.746913]  read_block_for_search.isra.38+0x2a3/0x370
[1417839.758645]  btrfs_search_slot+0x260/0x9b0
[1417839.768054]  btrfs_lookup_file_extent+0x4a/0x70
[1417839.778427]  btrfs_get_extent+0x15f/0x830
[1417839.787665]  ? submit_extent_page+0xc4/0x1c0
[1417839.797474]  ? __do_readpage+0x299/0x7a0
[1417839.806515]  __do_readpage+0x33b/0x7a0
[1417839.815171]  ? btrfs_releasepage+0x70/0x70
[1417839.824597]  extent_readpages+0x28f/0x400
[1417839.833836]  read_pages+0x6a/0x1c0
[1417839.841729]  ? startup_64+0x2/0x30
[1417839.849624]  __do_page_cache_readahead+0x13c/0x1a0
[1417839.860590]  filemap_fault+0x6c7/0x990
[1417839.869252]  ? xas_load+0x8/0x80
[1417839.876756]  ? xas_find+0x150/0x190
[1417839.884839]  ? filemap_map_pages+0x295/0x3b0
[1417839.894652]  __do_fault+0x32/0x110
[1417839.902540]  __handle_mm_fault+0xacd/0x1000
[1417839.912156]  handle_mm_fault+0xaa/0x1c0
[1417839.921004]  __do_page_fault+0x242/0x4b0
[1417839.930044]  ? page_fault+0x8/0x30
[1417839.937933]  page_fault+0x1e/0x30
[1417839.945631] RIP: 0033:0x33c4bae
[1417839.952927] Code: Bad RIP value.
[1417839.960411] RSP: 002b:00007f5a844f7350 EFLAGS: 00010206
[1417839.972331] RAX: 000000000000006e RBX: 1614b3ff6a50398a RCX: 0000000000000000
[1417839.988477] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000002
[1417840.004626] RBP: 00007f5a844f7420 R08: 000000000000006e R09: 00007f5a94aeccb8
[1417840.020784] R10: 00007f5a844f7350 R11: 0000000000000000 R12: 00007f5a94aecc79
[1417840.036932] R13: 00007f5a94aecc78 R14: 00007f5a94aecc90 R15: 00007f5a94aecc40

CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit bdf4d37b which is
commit 2bbcaaee upstream.

It is being reverted upstream, just hasn't made it there yet and is
causing lots of problems.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Cc: Qiujun Huang <hqjagain@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 63960260 upstream.

When evaluating access control over kallsyms visibility, credentials at
open() time need to be used, not the "current" creds (though in BPF's
case, this has likely always been the same). Plumb access to associated
file->f_cred down through bpf_dump_raw_ok() and its callers now that
kallsysm_show_value() has been refactored to take struct cred.

Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: bpf@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 7105e828 ("bpf: allow for correlation of maps and helpers in dump")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 60f7bb66 upstream.

The kprobe show() functions were using "current"'s creds instead
of the file opener's creds for kallsyms visibility. Fix to use
seq_file->file->f_cred.

Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 81365a94 ("kprobes: Show address of kprobes if kallsyms does")
Fixes: ffb9bd68 ("kprobes: Show blacklist addresses as same as kallsyms does")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b25a7c5a upstream.

The printing of section addresses in /sys/module/*/sections/* was not
using the correct credentials to evaluate visibility.

Before:

 # cat /sys/module/*/sections/.*text
 0xffffffffc0458000
 ...
 # capsh --drop=CAP_SYSLOG -- -c "cat /sys/module/*/sections/.*text"
 0xffffffffc0458000
 ...

After:

 # cat /sys/module/*/sections/*.text
 0xffffffffc0458000
 ...
 # capsh --drop=CAP_SYSLOG -- -c "cat /sys/module/*/sections/.*text"
 0x0000000000000000
 ...

Additionally replaces the existing (safe) /proc/modules check with
file->f_cred for consistency.
Reported-by: Dominik Czarnota <dominik.czarnota@trailofbits.com>
Fixes: be71eda5 ("module: Fix display of wrong module .text address")
Cc: stable@vger.kernel.org
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ed66f991 upstream.

In order to gain access to the open file's f_cred for kallsym visibility
permission checks, refactor the module section attributes to use the
bin_attribute instead of attribute interface. Additionally removes the
redundant "name" struct member.

Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8d1b73dd upstream.

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct module_sect_attrs {
	...
        struct module_sect_attr attrs[0];
};

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(*sect_attrs) + nloaded * sizeof(sect_attrs->attrs[0]

with:

struct_size(sect_attrs, attrs, nloaded)

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 16025184 upstream.

In order to perform future tests against the cred saved during open(),
switch kallsyms_show_value() to operate on a cred, and have all current
callers pass current_cred(). This makes it very obvious where callers
are checking the wrong credential in their "read" contexts. These will
be fixed in the coming patches.

Additionally switch return value to bool, since it is always used as a
direct permission check, not a 0-on-success, negative-on-error style
function return.

Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7c83d096 upstream.

Mark CR4.TSD as being possibly owned by the guest as that is indeed the
case on VMX.  Without TSD being tagged as possibly owned by the guest, a
targeted read of CR4 to get TSD could observe a stale value.  This bug
is benign in the current code base as the sole consumer of TSD is the
emulator (for RDTSC) and the emulator always "reads" the entirety of CR4
when grabbing bits.

Add a build-time assertion in to ensure VMX doesn't hand over more CR4
bits without also updating x86.

Fixes: 52ce3c21 ("x86,kvm,vmx: Don't trap writes to CR4.TSD")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703040422.31536-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d74fcfc1 upstream.

Inject a #GP on MOV CR4 if CR4.LA57 is toggled in 64-bit mode, which is
illegal per Intel's SDM:

  CR4.LA57
    57-bit linear addresses (bit 12 of CR4) ... blah blah blah ...
    This bit cannot be modified in IA-32e mode.

Note, the pseudocode for MOV CR doesn't call out the fault condition,
which is likely why the check was missed during initial development.
This is arguably an SDM bug and will hopefully be fixed in future
release of the SDM.

Fixes: fd8cb433 ("KVM: MMU: Expose the LA57 feature to VM.")
Cc: stable@vger.kernel.org
Reported-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703021714.5549-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5ecad245 upstream.

Bit 8 would be the "global" bit, which does not quite make sense for non-leaf
page table entries.  Intel ignores it; AMD ignores it in PDEs and PDPEs, but
reserves it in PML4Es.

Probably, earlier versions of the AMD manual documented it as reserved in PDPEs
as well, and that behavior made it into KVM as well as kvm-unit-tests; fix it.

Cc: stable@vger.kernel.org
Reported-by: Nadav Amit <namit@vmware.com>
Fixes: a0c0feb5 ("KVM: x86: reserve bit 8 of non-leaf PDPEs and PML4Es in 64-bit mode on AMD", 2014-09-03)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b9e10d4a upstream.

HVC_SOFT_RESTART is given values for x0-2 that it should installed
before exiting to the new address so should not set x0 to stub HVC
success or failure code.

Fixes: af42f204 ("arm64: hyp-stub: Zero x0 on successful stub handling")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Scull <ascull@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200706095259.1338221-1-ascull@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 68cf6173 upstream.

PAGE_HYP_DEVICE is intended to encode attribute bits for an EL2 stage-1
pte mapping a device. Unfortunately, it includes PROT_DEVICE_nGnRE which
encodes attributes for EL1 stage-1 mappings such as UXN and nG, which are
RES0 for EL2, and DBM which is meaningless as TCR_EL2.HD is not set.

Fix the definition of PAGE_HYP_DEVICE so that it doesn't set RES0 bits
at EL2.
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200708162546.26176-1-will@kernel.orgSigned-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e337bf19 upstream.

These devices claim to be 96kHz mono, but actually are 48kHz stereo with
swapped channels and unaligned transfers.

Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20200702071433.237843-1-marcan@marcan.stSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6a6ca788 upstream.

We have a Dell AIO, there is neither internal speaker nor internal
mic, only a multi-function audio jack on it.

Users reported that after freshly installing the OS and plug
a headset to the audio jack, the headset can't output sound. I
reproduced this bug, at that moment, the Input Source is as below:
Simple mixer control 'Input Source',0
  Capabilities: cenum
  Items: 'Headphone Mic' 'Headset Mic'
  Item0: 'Headphone Mic'

That is because the patch_realtek will set this audio jack as mic_in
mode if Input Source's value is hp_mic.

If it is not fresh installing, this issue will not happen since the
systemd will run alsactl restore -f /var/lib/alsa/asound.state, this
will set the 'Input Source' according to history value.

If there is internal speaker or internal mic, this issue will not
happen since there is valid sink/source in the pulseaudio, the PA will
set the 'Input Source' according to active_port.

To fix this issue, change the parser function to let the hs_mic be
stored ahead of hp_mic.

Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200625083833.11264-1-hui.wang@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ad155712 upstream.

The stack object “info” in snd_opl3_ioctl() has a leaking problem.
It has 2 padding bytes which are not initialized and leaked via
“copy_to_user”.
Signed-off-by: xidongwang <wangxidong_97@163.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1594006058-30362-1-git-send-email-wangxidong_97@163.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d9d54202 ]

We should not trigger a warning when a memory allocation fails. Remove
the WARN_ON().

The warning is constantly triggered by syzkaller when it is injecting
faults:

[ 2230.758664] FAULT_INJECTION: forcing a failure.
[ 2230.758664] name failslab, interval 1, probability 0, space 0, times 0
[ 2230.762329] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28
...
[ 2230.898175] WARNING: CPU: 3 PID: 1407 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:6265 mlxsw_sp_router_fib_event+0xfad/0x13e0
[ 2230.898179] Kernel panic - not syncing: panic_on_warn set ...
[ 2230.898183] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28
[ 2230.898190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014

Fixes: 3057224e ("mlxsw: spectrum_router: Implement FIB offload in deferred work")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ced4799d ]

Change the way the "magic-packet" DT property is handled in the
macb_probe() function, matching DT binding documentation.
Now we mark the device as "wakeup capable" instead of calling the
device_init_wakeup() function that would enable the wakeup source.

For Ethernet WoL, enabling the wakeup_source is done by
using ethtool and associated macb_set_wol() function that
already calls device_set_wakeup_enable() for this purpose.

That would reduce power consumption by cutting more clocks if
"magic-packet" property is set but WoL is not configured by ethtool.

Fixes: 3e2a5e15 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c8b1d743 ]

we need to set 'active_vfs' back to 0, if something goes wrong during the
allocation of SR-IOV resources: otherwise, further VF configurations will
wrongly assume that bp->pf.vf[x] are valid memory locations, and commands
like the ones in the following sequence:

 # echo 2 >/sys/bus/pci/devices/${ADDR}/sriov_numvfs
 # ip link set dev ens1f0np0 up
 # ip link set dev ens1f0np0 vf 0 trust on

will cause a kernel crash similar to this:

 bnxt_en 0000:3b:00.0: not enough MMIO resources for SR-IOV
 BUG: kernel NULL pointer dereference, address: 0000000000000014
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 0 P4D 0
 Oops: 0000 [#1] SMP PTI
 CPU: 43 PID: 2059 Comm: ip Tainted: G          I       5.8.0-rc2.upstream+ #871
 Hardware name: Dell Inc. PowerEdge R740/08D89F, BIOS 2.2.11 06/13/2019
 RIP: 0010:bnxt_set_vf_trust+0x5b/0x110 [bnxt_en]
 Code: 44 24 58 31 c0 e8 f5 fb ff ff 85 c0 0f 85 b6 00 00 00 48 8d 1c 5b 41 89 c6 b9 0b 00 00 00 48 c1 e3 04 49 03 9c 24 f0 0e 00 00 <8b> 43 14 89 c2 83 c8 10 83 e2 ef 45 84 ed 49 89 e5 0f 44 c2 4c 89
 RSP: 0018:ffffac6246a1f570 EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000000000000b
 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff98b28f538900
 RBP: ffff98b28f538900 R08: 0000000000000000 R09: 0000000000000008
 R10: ffffffffb9515be0 R11: ffffac6246a1f678 R12: ffff98b28f538000
 R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffc05451e0
 FS:  00007fde0f688800(0000) GS:ffff98baffd40000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000014 CR3: 000000104bb0a003 CR4: 00000000007606e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 PKRU: 55555554
 Call Trace:
  do_setlink+0x994/0xfe0
  __rtnl_newlink+0x544/0x8d0
  rtnl_newlink+0x47/0x70
  rtnetlink_rcv_msg+0x29f/0x350
  netlink_rcv_skb+0x4a/0x110
  netlink_unicast+0x21d/0x300
  netlink_sendmsg+0x329/0x450
  sock_sendmsg+0x5b/0x60
  ____sys_sendmsg+0x204/0x280
  ___sys_sendmsg+0x88/0xd0
  __sys_sendmsg+0x5e/0xa0
  do_syscall_64+0x47/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Fei Liu <feliu@redhat.com>
CC: Jonathan Toppins <jtoppins@redhat.com>
CC: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>